Quick Start Guide

Fault Cause Solution
SIM card error
The SIM card is damaged
Contact your network service
provider
The SIM card is not in position Check the SIM card
The metal face of the SIM card
is polluted
Clean the SIM card
with a clean cloth
Poor received
signal quality
Signals are obstructed, For in-
stance, radio waves cannot be
eff ectively transmitted nearby a
high building or in a basement
Move to a place where signals
can be eff ectively transmitted
Line congestions occur when
you use the mobile phone in
high-traffi c hours
Avoid use the mobile phone in
hightraffi c hours
The mobile
phone cannot be
powered on
The battery energy
is exhausted
Charge the battery
Calls cannot be
dialled
Call barring is activated Cancel call barring
The mobile
phone cannot
connect the
network
The SIM card is invalid
Contact your network service
provider
The mobile phone is not in
a service area of the GSM
network
Move to the network operator´s
service area
The signal is weak
Move to a place where the
signal quality is high
The battery
cannot be
charged
The charging voltage does
not match the voltage range
indicated on the charger
Ensure the charging voltage
matches the voltage range
indicated on the charger
An improper charger is used
Use the charger specially
designed for the mobile phone
Poor contact
Ensure the charger plug is in
good contact with the mobile
phone.
1
Side key
9
Right Key
2
Centre Key
10
End/Power Key
3
Left Key
11
Keypad
4
Dial Key
12
USB Jack
5
Headset Jack
13
Torch Key
6
Earpiece
14
Camera
7
Display
15
Speaker
8
Navigation Key
16
Torch
Icon
Description
Indicates the network signal strength.
Indicates the current battery capacity.
Indicates that there is an unread message.
Indicates that there is missed call.
Indicates that the current Sound Status is the Ring only.
Indicates that the current Sound Status is the Vibrate only.
Indicates that the current Sound Status is the Silent only.
Indicates that the current profi le mode is the Headset mode.
Indicates that the current alarm clock is set as activated.
Indicates the current keypad-locked state.
Indicates that the Bluetooth is turn on.
Accessory item Model number
Rechargeable battery 523450AR-E
Lithium Ion (Li-Ion) battery.
Headset JYK-E112
Attach your purchase receipt here.
Serial No. (found on the carton box or in the battery compartment) Date of purchase
Name and address of dealer
Controls
Status icons
The table below lists various icons that might appear on the status bar while using the phone.
Apart from the icons for signal strength level and power, other icons are displayed as per the
current mode and priority of the phone.
Function of Keys
The mobile phone provides the following keys:
•
Left and right key
The bottom line on the screen displays the functions of the Left and Right soft key.
•
Dial key
Press it to originate a call by entering the called number or selecting a contact from
the phonebook; or press it to receive an incoming call; or press it in standby state to show
the latest call records.
•
End/Power key
Press it to end a call being dialled or end an ongoing call; or press it to exit the menu and return
to the standby state. You can hold it for a while to can power on/off the mobile phone.
•
Navigation key
Press them to scroll the options when browsing a function list. In edit state, press direction
keys to navigate.
•
OK key (Left soft key)
Press it to confi rm a selection.
•
Number keys, * key and # key
Press number keys 0 through 9 to input or edit state to input numbers and characters;
Hold the # key up to 2s in standby state to activate or deactivate the silent mode. Press the #
key in edit state to switch between input methods. Pressing the * key in edit status to select
a symbol. In idle screen, you can press left soft key then * key to lock keypad. When the keypad
is locked, you can press left soft key then * key to unlock it.
Press and hold the 0 key up to 2s to input “+ˮ in standby interface. When the symbol “+ˮ
appears, press the 0 key quickly to input “Pˮ or “Wˮ are used for calling the extension; “+ˮ
are used for dialling an international call.
How to handling the SIM card and microSD card
•
1 ( ) key
Long press it to dial the voicemail number, if you have set voicemail number.
•
2-9 key
Long press it to dial the speed dial number, if you have set speed dial number.
Important safety instructions
Hold the End key for a while to power on the mobile phone. A power-on animation appears on
the display screen and the phone sounds.
*1
Input the phone lock code and press the OK key if the mobile phone prompts you to input the
phone lock code. The original code is 1122.
Input the PIN and press the OK key if the mobile phone prompts you to input the PIN. The PIN
is provided by the network operator for new opening SIM card.
Enter the standby interface.
To power off mobile phone, hold End key for a while.
*1 The preset melodies in this product are used with permission of ©2014 Copyrights Vision Inc.
Charging the Battery
The lithium battery delivered with the mobile phone can be put into use immediately after being
unpacked.
Battery level indication:
Your mobile phone can monitor and display the battery state.
Normally the remaining energy of the battery is indicated by the battery level icon at the upper
right corner of the display screen.
When the battery energy is insuffi cient, the mobile phone prompts “Battery lowˮ.
A charging animation appears when the battery is being charged. When the charging is complete,
the animation disappears.
Using a travel adaptor:
Install the battery into the mobile phone before charging the battery.
Connect the adaptor of the travel charger with the charging slot in the mobile phone. Ensure that
the adaptor is fully inserted.
Insert the plug of the travel charger to an appropriate power outlet.
During the charging, the battery level grids in the battery icon keep flickering till the battery is fully
charged.
It is normal when the battery is become hot during the charging period.
The battery icon does no longer flicker when the charging process ends.
Note:
Ensure that the mobile phone, the plug of the earphone, and the plug of the USB cable are inserted
in the right direction. Inserting them in a wrong direction may cause charging failure
or other problems.
Before the charging, ensure that the standard voltage and frequency of the local mains supply
match the rated voltage and power of the travel charger.
Appendix 1: For your future reference
We recommend keeping a record of the following information to assist with any repair under
warranty:
Appendix 2: Troubleshooting
If you fi nd exceptions when operating the mobile phone, restore the factory setting and then
refer to the following table to solve the problem. If the problem persists, contact the distributor
of service provider.
•
This phone is designed to operate on GSM network - GSM 900/1800MHz.
•
This equipment is designed for use in European Union.
•
In the event of problems, you should contact your equipmnet supplier in the fi rst instance.
•
For use in other countries, please contact your equipment supplier.
General information
microSD
SIM
Additional/replacement accessories
Declaration of Conformity
Hereby, Panasonic Marketing Europe GmbH declares that the radio equipment type Mobile Phone KX-
TF200 is in compliance with Directive 2014/53/EU (for EU) and The Radio Equipment
Regulations 2017 (for UK). The full text of the EU and UK declaration of conformity is available at the
following internet address: https://www.ptc.panasonic.eu/compliance-documents
Confi rmation of Compliance with UK Regulations
This product complies with UK relevant Regulations and Standards (being those relevant for England,
Wales and Scotland).
Important information Important information Important information Important informationImportant informationImportant informationImportant information
13 1412111098
2023_05_26 Panasonic KX TF200 GQ_EN_v06.indd 2
2023_05_26 Panasonic KX TF200 GQ_EN_v06.indd 2
24.07.2023 10:48:47
24.07.2023 10:48:47