Operating Instructions
Table Of Contents
- Important Information
- Table of Contents
- Introduction and Installation
- Preparation
- Connections and Setup
- Document Requirements
- Help
- Volume
- Initial Programming
- Printer
- Scanner
- Scanner
- 4.1 Scanning from the unit (Push Scan)
- 4.1.1 Scan to Multi-Function Viewer
- 4.1.2 Scan to save as a file
- 4.1.3 Scan to Email
- 4.1.4 Scan to OCR
- 4.1.5 Scan to email address (KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only)
- 4.1.6 Scan to FTP server (KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only)
- 4.1.7 Scan to SMB folder (KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only)
- 4.2 Scanning from a computer (Pull Scan)
- 4.1 Scanning from the unit (Push Scan)
- Scanner
- Copier
- Fax (KX-MB2025/KX-MB2030 only)
- Sending Faxes
- Receiving Faxes
- 6.6 Selecting the way to use your unit
- 6.7 Receiving a fax automatically – Auto answer ON
- 6.8 Receiving a fax manually – Auto answer OFF
- 6.9 Using the unit with an answering machine
- 6.10 Receive polling (retrieving a fax placed on another fax machine)
- 6.11 Junk fax prohibitor (preventing fax reception from undesired callers)
- 6.12 Receiving a fax on your computer
- 6.13 Web fax preview (KX-MB2030, LAN connection only)
- Caller ID (KX-MB2025/KX-MB2030 only)
- Programmable Features
- Useful Information
- Help
- Reports and Displays
- Troubleshooting
- 10.3 When a function does not work
- 10.3.1 General
- 10.3.2 Printing problems
- 10.3.3 Scanner
- 10.3.4 Copier
- 10.3.5 Fax (KX-MB2025/KX-MB2030 only)
- 10.3.6 Network (KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only)
- 10.3.7 Using an answering machine (KX-MB2025/KX-MB2030 only)
- 10.3.8 If a power failure occurs
- 10.3.9 Firewall setting tool for Microsoft Windows XP Service Pack 2 or later/Windows Vista users (KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only)
- 10.3.10 Notice for KX-MB200/KX-MB700/KX-FLB880 series users
- 10.3 When a function does not work
- Paper Jams
- Cleaning
- General Information
- Index
5. Close the top cover by holding the indentations on
both sides of the unit, until locked.
11.1.2 When the recording paper is not fed
into the unit properly
The display will show the following:
– “CHECK PAPER #1 PRESS START”
1 Pull the paper input tray until it clicks into place, then
pull it completely out, lifting the front part of the tray.
Remove the recording paper and straighten.
2 Re-load the recording paper.
3 Insert the paper input tray into the unit, lifting the front
part of the tray. Then push it completely into the unit.
Note:
R If the message is still displayed, check the recording
paper specifications and load the recording paper
again. See page 14 for details.
11.1.3 When the recording paper in the
manual input tray is not fed into the unit
properly
The display will show the following.
– “CHECK PICK UP INPUT TRAY #2”
1 Remove the recording paper.
2 Re-insert the recording paper.
92
11. Paper Jams