Panasonic Telephone Systems Panasonic KX-TD208E, KXTD208E, TD208E, KX-TD208, KX TD208, TD208 Digital Super Hybrid System www.voicesonic.com Phone: 877-289-2829 KX-TD208E g Star n i t ted et G This booklet tells you how to install your KX-TD208 quickly and easily and gives you initial operating instructions. For further information, see the enclosed "Operating lnstructions.
Contents Preparation Describes the included accessories and required tools for installation. Page 3 Connection Shows you how to install your system from set-up to initial use. Page 4 Basic Programming Describes the programs necessary depending on your contract and requirements. Basic Operations Page 6 Describes how to make and receive calls in order to confirm the connections. Programming Using A Personal Computer Page 8 Shows you a personal comput er connection and how to program by using it.
Preparation Before installing your system ¢ Check the package contents. The included materials are: DIGITAL SUPER HYBRID SYSTEM POWER Main Unit ... one Floppy Disk for PC Programming ... one Screws and Washers ... three AC Cord ... one *Do not close the transparent part into the black part before inserting the wires. 4-pin Plugs* ... eleven ISDN Line Cord ...
Connections 1. Open the front cove Reset Switch 2. Connect the include ISDN Port 2 ISDN Port 1 ISDN Modular Jack 3. Connect the user A B EXTN.1 D I G I T A L S U P E R H Y B R I D S Y S TEM POWER Preparation 1. Extension Jack To the "Extension Jack" RS-232C Port (Serial Interface) User-supplied Telephone Socket Strip the wire cover with pliers. 4. socke cover scre Remove the socket cover with flathead screwdriver. 4. Connect the PC to You can program the syste The required operating syste 5.
1. Loosen the screw. 2. Slide the cover toward the right DIGITAL SUPER HYBRID SYSTEM while pressing the " " mark. POWER screw ISDN line cord to "ISDN Port 1" and the Telephone socket to the exchange line. To the Exchange Line supplied extension line cord to the "Extension Jack" and telephone equipment. A 2. 3. A B B Insert the user-supplied telephone wires completely into the holes of the included plugs. 5. Press the transparent part into the black part firmly.
Basic Programming Some programming is required for basic operation. Check your contract with the telephone company and program as needed. The following flow chart will tell you which programming is required for your system. Please program your system accordingly. Before programming Connect a tone-type single line telephone to jack number 1 for programming. Check: • Your telephone is on-hook. • No calls are on hold at your telephone.
Basic Programming Step 3. Follow the chart according to your programming type . A B C D [406] ISDN Configuration 4 0 6 ISDN port no. (1,2, 1 ) [407] Multiple Subscriber Number (MSN) Set 4 0 7 ISDN location MSN port no. no. 16 digits max. (1,2, ) (01···10) (0···9) [408]–[409] Extension Ringing Assignment —Day / Night for ISDN Consecutive entries 4 ISDN location extension no. port no. no. (21 ... 28, 31...34) Y - Day...8 (1,2, ) (01···10) Night...
Basic Operations Let’s try to make and receive a call in order to confirm the connections. Making a call to another extension and receiving it ¢ Making a call from extension 21 to extension 22 At extension 21 1. Off-hook. 2. Dial 2 2 . At extension 22 1. Off-hook. Did it work??? Making a call to an outside party ¢ Calling a Speaking Clock 1. Off-hook. 2. Enter 9 . 3. Dial 1 2 3 .
Programming Using A Personal Computer Connection EXTN. 8 EXTN. 7 EXTN. 6 EXTN. 5 EXTN. 4 HING SYSTEM EXTN. 3 EXTN. 2 EXTN. 1 Connect your personal computer to the RS232C port with the usersupplied serial printer cable. The Cable must be shielded and the maximum length is 2 m. ¢ Refer to the following chart for the pin configuration; Port on your system 9-pin port on a PC Pin No. Pin No.
Programming Using A Personal Computer Programming You can program the system data using the application software in the included floppy disk on the IBM-PC/AT or a compatible personal computer. The system programming data can be stored either on the floppy disk or on your hard disk. To use the floppy disk for PC programming, you must have MS-DOS (or equivalent) version 5.0 or later. A minimum of 450K of free conventional memory is required. ¢ File Configuration The file name: TD208.
Assistance Information If you have any trouble, see the Trouble Shooting Section in the Operating Instructions or consult your dealer. Panasonic Telephone Systems See More Panasonic Manuals www.voicesonic.
