User's Guide Telephone K10059

ManualsBrandsPanasonic ManualsTelephoneK10059

SecurityLink

Plus

User’s Guide

K10059 6/04 Rev. A

SecurityPhone.book 1 ページ２００４年７月２１日　水曜日　午後６時５８分

Summary of content (56 pages)

PAGE 1
SecurityPhone.book 1 ページ２００４年７月２１日水曜日午後６時５８分 SecurityLink® PlusTM User’s Guide K10059 6/04 Rev.
PAGE 2
SecurityPhone.book 2 ページ２００４年７月２１日水曜日午後６時５８分 This phone can be connected to an ADT Security System and used as an additional keypad interface. You can program/control system functions using the buttons on the telephone front panel. The security system will provide the telephone line and power supply, and has priority over the telephone functions. Overview N Communication with the Security System The phone functions as a user interface (keypad/display) for the security system.
PAGE 3
SecurityPhone.book 3 ページ２００４年７月２１日水曜日午後６時５８分 Contents Location of Controls . . . . . . . . . 4 Pager . . . . . . . . . . . . . . . . . . 34 Security System Displays . . . . 5 Schedules . . . . . . . . . . . . . . . . . 35 Entry/Exit Delays . . . . . . . . . . . Entry Delay . . . . . . . . . . . . . . . Exit Delay . . . . . . . . . . . . . . . . Exit Alarms . . . . . . . . . . . . . . . Viewing the Event Log . . . . . . 38 6 6 6 6 Arming the System . . . . . . . . . . 7 Setting the Away mode .
PAGE 4
SecurityPhone.book 4 ページ２００４年７月２１日水曜日午後６時５８分 Location of Controls Base Unit Display [ADT] Press to enter the function menu for the security system. PANIC keys Press and hold for two seconds in event of emergency (panic). [STOP] Press to exit programming or terminate the function menu. [FUNCTION/EDIT] Press to enter the function menu for the telephone and Answering systems. [ERASE] Press to erase the entered code or number. Navigator Key Press the arrow to scroll through menu or select items.
PAGE 5
SecurityPhone.book 5 ページ２００４年７月２１日水曜日午後６時５８分 Security System Displays Base unit 1 Cordless handset 1 12:00AM DEC.31 Received calls READY IN USE IN USE SP 2 READY Received calls [1] 2 01 MESSAGE ADT PANIC P L AY 3 4 1 The base unit and cordless handset display status icons below: Icon Meaning READY The phone is ready to arm the security system. ARMED The security system is armed. NOT RDY The phone is not ready to arm the security system.
PAGE 6
SecurityPhone.book 6 ページ２００４年７月２１日水曜日午後６時５８分 Entry/Exit Delays Entry Delay You can have time to re-enter your house from pre-selected door by programming entry delay times. You must disarm the system before entry delay time expires. The phone beeps until you disarm the system. Confirm with your installer for your delay time. Exit Delay You can have time to go out through the exit door without cancelling an alarm. The exit delay time starts immediately after you arm the system.
PAGE 7
SecurityPhone.book 7 ページ２００４年７月２１日水曜日午後６時５８分 Arming the System You can set the security mode through the function menu using the base unit or handset. There are 4 modes, AWAY, STAY, Night-Stay and INSTANT. If you want to change the security mode after you arm the system, disarm the system, then set your required mode through the function menu.
PAGE 8
SecurityPhone.book 8 ページ２００４年７月２１日水曜日午後６時５８分 Arming the System Setting the Away mode When nobody (including pets) remains at home, select this mode. When you set the Away mode, — the entire system (interior and perimeter) is armed, and — exit delay begins so that you can leave through the entry/exit door. Base Unit 1 Press [ADT]. 2 Press [g] at “ARM”. 3 Scroll to “AWAY” by pressing [d] or [B]. g ARM g AWAY 4 Press [g], then go out through the entry/exit door during the exit delay time.
PAGE 9
SecurityPhone.book 9 ページ２００４年７月２１日水曜日午後６時５８分 Arming the System Setting the Stay mode When you want to arm the system while persons stay inside, select this mode. When you set the Stay mode, — the perimeter zones, such as protected windows and doors, are armed — interior sensors are left disarmed — exit delay begins so that you can leave through the exit/entry door, and — if the protected perimeter windows and doors are opened, an alarm sounds immediately. Base Unit 1 Press [ADT].
PAGE 10
SecurityPhone.book 10 ページ２００４年７月２１日水曜日午後６時５８分 Arming the System Setting the Night-Stay mode When you want to get more increased security than the Stay mode, select this mode. When you set the Night-Stay mode, — the perimeter zones and pre-selected interior sensors (programmed by your installer) are armed, and — if the protected perimeter windows and doors are opened or interior zones are violated, an alarm sounds immediately. Base Unit 1 Press [ADT]. 2 Press [g] at “ARM”.
PAGE 11
SecurityPhone.book 11 ページ２００４年７月２１日水曜日午後６時５８分 Arming the System Setting the Instant mode When you stay at home and no one intends to use an entry/exit door, select this mode. When you set the Instant mode, — the system is armed same as the Stay mode, and — if the protected perimeter windows and doors are opened, an alarm sounds immediately. Base Unit 1 Press [ADT]. 2 Press [g] at “ARM”. g ARM then press [g]. g INSTANT • The armed INSTANT message is displayed.
PAGE 12
SecurityPhone.book 12 ページ２００４年７月２１日水曜日午後６時５８分 Disarming the security system To disarm the security system through the function menu You can disarm the system by turning the security mode off through the function menu. Base Unit 1 Press [ADT]. 2 Press [g] at “DISARM”. 3 Enter your security code. • If you entered the wrong security code, the phone will go back to the previous display. Try again from step 2. g DISARM ENTER CODE ---- 4 Press [STOP] to go to the standby mode.
PAGE 13
SecurityPhone.book 13 ページ２００４年７月２１日水曜日午後６時５８分 Disarming the security system When alarm sounds while the system is armed: 1 Enter your security code. • The alarm stops, the security system is disarmed. • Check the alarm display. If the protected doors or windows remain open, close them. 2 Press [ADT] to go to the standby mode. 3 Enter your security code, then press [1] to go to the ready status. • A memory of alarm is cleared. ALARM SIGNAL IS NOT SENT TO THE CUSTOMER MONITORING CENTER.
PAGE 14
SecurityPhone.book 14 ページ２００４年７月２１日水曜日午後６時５８分 Bypassing Protection Zones Using this mode, you can set the selected zones to be unprotected. After setting this mode, set the security mode as desired. While the security system is armed, you can not set the Bypass. To bypass zones, disarm the security system (p. 12). • WHEN CERTAIN ZONES ARE BYPASSED, THE SYSTEM DOES NOT PROTECT THE BYPASSED ZONE, THE ALARM DOES NOT SOUND, AND AN ALARM SIGNAL IS NOT SENT TO THE CUSTOMER MONITORING CENTER.
PAGE 15
SecurityPhone.book 15 ページ２００４年７月２１日水曜日午後６時５８分 Bypassing Protection Zones 6 Press [g] (ENTER). • The “Bypass” message for bypassed zone number is displayed momentarily. • A confirmation tone (one beep) is heard for each bypassed zone. • If a confirmation tone (one beep) is not heard, you entered the wrong security code in step 4 or wrong zone number in step 5, or the security mode is armed. The setting is not saved. Try again from step 3. 7 Press [STOP] to go to the standby mode.
PAGE 16
SecurityPhone.book 16 ページ２００４年７月２１日水曜日午後６時５８分 Bypassing Protection Zones Quick Bypass If the Quick Bypass is programmed by the security system installer, you can set all faulted (open) zones unprotected at once. Confirm with your installer if the Quick Bypass is active for your system. When Quick Bypass is used, all faulted (open) zones are unprotected, the alarm does not sound, and an alarm signal is not sent to the Customer Monitoring Center.
PAGE 17
SecurityPhone.book 17 ページ２００４年７月２１日水曜日午後６時５８分 Chime Mode Even if the security system is not armed, the Chime mode can alert you by three beeps and announcement to the opening of a perimeter door or window. Refer to “Chime Mode” on page 22 in the 3000EN Security Systems User’s Guide. While the security system is armed, you can not turn the Chime on or off. To turn on, disarm the security system (p. 12). Make sure all perimeter doors and windows are closed and READY is displayed.
PAGE 18
SecurityPhone.book 18 ページ２００４年７月２１日水曜日午後６時５８分 Setting the Date and Time You can set the date and time of the security system by following the operation below. The date and time setting for the telephone should be programmed through the “Telephone” menu. While the security system is armed, you can not set the Date and Time. To set, disarm the security system (p. 12). Base Unit 1 Press [ADT]. 2 Scroll to “OTHER FUNCTIONS” by pressing [d] or [B], then press [g].
PAGE 19
SecurityPhone.book 19 ページ２００４年７月２１日水曜日午後６時５８分 Setting the Date and Time To view the current date and time 1 Press [ADT]. 2 Scroll to “OTHER FUNCTIONS” by pressing [d] or [B], then press [g]. 3 Scroll to “DATE/TIME” by pressing [d] or [B], then press [g]. 4 Enter your security code. • The current date and time are displayed. • When finished, press [0] to [9] or [#], or wait for 30 seconds. Then press [OFF] or [STOP] to exit the menu.
PAGE 20
SecurityPhone.book 20 ページ２００４年７月２１日水曜日午後６時５８分 PANIC Keys The PANIC keys can manually activate emergency (panic) functions, and send signals to the Customer Monitoring Center, if the system is being monitored. Using the PANIC Keys If the PANIC key is pressed while a phone is in use, the operation of a phone is cancelled. Base Unit Press and hold the required PANIC keys for two seconds. PANIC keys (FIRE, POLICE, MED.) Handset 1 Press the soft key ( PANIC ).
PAGE 21
SecurityPhone.book 21 ページ２００４年７月２１日水曜日午後６時５８分 PANIC Keys To stop and clear a burglary alarm 1 Enter the security code. • If the system is armed, the system is disarmed. • Alarm stops. 2 Press [ADT]. 3 Enter your security code, then press [1]. • Alarm display will be cleared. • “ READY ” will be displayed. 4 Press [STOP] to go to the standby mode. IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location.
PAGE 22
SecurityPhone.book 22 ページ２００４年７月２１日水曜日午後６時５８分 Remote Phone Control You can access the security system from a touch tone phone located off the premises. You can regain system status information over the telephone by voice guidance, control your security system by entering function commands remotely with the telephone dialing buttons. To use this feature, you must program your own remote code*1. The factory preset remote code is “11”.
PAGE 23
SecurityPhone.book 23 ページ２００４年７月２１日水曜日午後６時５８分 Selecting the Function (Macro) If a series of commands (up to 16 keystrokes) are programmed in the system’s memory by your installer and the commands are assigned to the “A”, “B”, “C” and “D” keys on a touchpad, you can operate the desired function by selecting “FUNCTION A”, “FUNCTION B”, “FUNCTION C” or “FUNCTION D” through the function menu. Refer to “Macro Key Programming & Usage” on pages 25 to 26 in the 3000EN Security Systems User’s Guide.
PAGE 24
SecurityPhone.book 24 ページ２００４年７月２１日水曜日午後６時５８分 Device Commands If some devices are set up for your system, you can activate or deactivate certain lights or other devices using the Device Commands menu. Confirm with your installer for devices set up for your system. Refer to “Using Device Commands” on page 27 in the 3000EN Security Systems User’s Guide. To activate/deactivate devices Base Unit 1 Press [ADT]. 2 Scroll to “OTHER FUNCTIONS” by pressing [d] or [B], then press [g].
PAGE 25
SecurityPhone.book 25 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels Adding User Code Refer to “Security Codes & Authority Levels” on pages 30 to 31 in the 3000EN Security Systems User’s Guide. While the security system is armed, you can not turn on this function. To turn on, disarm the security system (p. 12). Make sure all perimeter doors and windows are closed and READY is displayed. Ex. To add a user number “08” and its security code “1234” in the system Base Unit 1 Press [ADT].
PAGE 26
SecurityPhone.book 26 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels 8 Press [g] (ENTER). • If a confirmation tone (one beep) is not heard, you entered the wrong security code in step 5 or wrong user number in step 6. The setting is not saved. Try again from step 4. 9 Press [STOP] to go to the standby mode. Handset : Press the soft key ( ADT ), follow steps 2 to 5 on the previous page, and enter the user number of 2 digits (03 to 49), using the cordless handset.
PAGE 27
SecurityPhone.book 27 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels Deleting User Code You can delete the user code and programmed attributes except assigned partition. Refer to “Delete User Code” on page 31 in the 3000EN Security Systems User’s Guide. While the security system is armed, you can not turn on this function. To turn on, disarm the security system (p. 12). Make sure all perimeter doors and windows are closed and READY is displayed. Base Unit 1 Press [ADT].
PAGE 28
SecurityPhone.book 28 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels Authority Level You can set the authority level to the selected user. You can select four authority levels, “Standard User”, “Arm only”, “Guest” and “Duress” through the AUTHORITY LEVEL menu. Refer to “Authority Level Definitions” on page 30 in the 3000EN Security Systems User’s Guide. While the security system is armed, you can not turn on this function. To turn on, disarm the security system (p. 12).
PAGE 29
SecurityPhone.book 29 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels 8 Press [g] (ENTER). • If a confirmation tone (one beep) is not heard, you entered the wrong security code in step 5 or wrong user number in step 6. The setting is not saved. Try again from step 4. 9 Press [STOP] to go to the standby mode. Handset : Press the soft key ( ADT ), and follow steps 2 to 5 on the previous page, and enter the user number of 2 digits, using the cordless handset. Press the soft key ( OK ).
PAGE 30
SecurityPhone.book 30 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels Access Group You can assign users to a group (1 to 8) and select the access group for “Schedule” mode. Refer to “Access group” on page 31 in the 3000EN Security Systems User’s Guide. While the security system is armed, you can not turn on this function. To turn on, disarm the security system (p. 12). Make sure all perimeter doors and windows are closed and READY is displayed. Base Unit 1 Press [ADT].
PAGE 31
SecurityPhone.book 31 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels 9 Press [STOP] to go to the standby mode. Handset : Press the soft key ( ADT ), follow steps 2 to 5 on the previous page, and enter the user number of 2 digits, using the cordless handset. Press the soft key ( OK ). Follow step 7 on the previous page. Press the soft key ( OK ), then press [OFF] to go to the standby mode. • Enter a correct security code and user number in steps 5 and 6.
PAGE 32
SecurityPhone.book 32 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels RF User Number If you enroll a wireless button device (keyfob) in system, you need to set the zone number for the device. Refer to “RF User Number” on page 31 in the 3000EN Security Systems User’s Guide. While the security system is armed, you can not turn on this function. To turn on, disarm the security system (p. 12). Make sure all perimeter doors and windows are closed and READY is displayed.
PAGE 33
SecurityPhone.book 33 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels Handset : Press the soft key ( ADT ), follow steps 2 to 5 on the previous page, and enter the user number of 2 digits, using the cordless handset. Press the soft key ( OK ). Follow step 7 on the previous page. Press the soft key ( OK ), then press [OFF] to go to the standby mode.
PAGE 34
SecurityPhone.book 34 ページ２００４年７月２１日水曜日午後６時５８分 Security Codes & Authority Levels Pager If the Pager setting is turned on, the phone can automatically send a message to a pager, when the system is armed or disarmed by the programmed user code. The factory preset is ON. Refer to “Pager On/Off” on page 31 in the 3000EN Security Systems User’s Guide. Make sure all perimeter doors and windows are closed and READY is displayed. While the security system is armed, you can not turn on this function.
PAGE 35
SecurityPhone.book 35 ページ２００４年７月２１日水曜日午後６時５８分 Schedules Handset : Press the soft key ( ADT ), follow steps 2 to 5 on the previous page, and enter the user number of 2 digits, using the cordless handset. Press the soft key ( OK ). Follow step 7 on the previous page. Press the soft key ( OK ), then press [OFF] to go to the standby mode. Schedules Refer to “Scheduling” on pages 35 to 36 in the 3000EN Security Systems User’s Guide. Base Unit 1 Press [ADT].
PAGE 36
SecurityPhone.book 36 ページ２００４年７月２１日水曜日午後６時５８分 Schedules 6 Enter the event number (00 to 07), then press [*]. Refer to the Event Table on page 37 for available events. When selecting event number “01”, enter the output number, then press [*]. When selecting event number “02”, enter the access group number, then press [*]. When selecting event number “03” to “07”, enter the partition number, then press [*].
PAGE 37
SecurityPhone.book 37 ページ２００４年７月２１日水曜日午後６時５８分 Schedules 7 To continue with creating schedules, repeat from step 5. To finish creating schedules, wait for 30 seconds, then press [STOP] to go to the standby mode. Handset : Press the soft key ( ADT ), and follow steps 2 to 6 on the previous page, using the cordless handset. Press [OFF] to go to the standby mode. • To exit the menu, wait for 30 seconds, then press [STOP] or [OFF]. Event Table Event No.
PAGE 38
SecurityPhone.book 38 ページ２００４年７月２１日水曜日午後６時５８分 Viewing the Event Log The phone can record up to 100 events in a log. Event log is sorted by the most recent to the oldest. When the 101st event is recorded, the oldest one is deleted. Refer to “Event Logging Procedures” on pages 37 to 38 in the 3000EN Security Systems User’s Guide. Base Unit 1 Press [ADT]. 2 Scroll to “OTHER FUNCTIONS” by pressing [d] or [B], then press [g]. 3 Scroll to “VIEW EVENT LOG” by pressing [d] or [B], then press [g].
PAGE 39
SecurityPhone.book 39 ページ２００４年７月２１日水曜日午後６時５８分 Testing the System You can check the system for proper operation. Before testing the system, you must disarm the security mode and close all protected windows, doors, etc. Refer to “Testing the System (To Be Conducted Weekly)” on pages 39 to 40 in the 3000EN Security Systems User’s Guide. Make sure all perimeter doors and windows are closed and READY is displayed. Base Unit 1 Press [ADT]. 2 Scroll to “TEST” by pressing [d] or [B], then press [g].
PAGE 40
SecurityPhone.book 40 ページ２００４年７月２１日水曜日午後６時５８分 Checking the Current Status Display Status You can display faulted zones and a current system status, using this feature. Refer to “Checking For Open Zones” on page 14 in the 3000EN Security Systems User’s Guide. Make sure all perimeter doors and windows are closed and READY is displayed. Base Unit 1 Press [ADT]. 2 Scroll to “STATUS REQUEST” by pressing [d] or [B], then press [g].
PAGE 41
SecurityPhone.book 41 ページ２００４年７月２１日水曜日午後６時５８分 Checking the Current Status Voice Status The phone announces faulted zones and a current security status when this feature is turned on. Refer to “Checking For Open Zones” on page 14 in the 3000EN Security Systems User’s Guide. Make sure all perimeter doors and windows are closed and READY is displayed. Base Unit 1 Press [ADT]. 2 Scroll to “VOICE STATUS” by pressing [d] or [B], then press [g].
PAGE 42
SecurityPhone.book 42 ページ２００４年７月２１日水曜日午後６時５８分 Direct Commands You can set the security mode using a security code and direct command. Confirm with your installer or refer to the 3000EN Security Systems User’s Guide for available direct commands. While the security system is armed, you can not use this function. To turn on, disarm the security system (p. 12). Base Unit 1 Press [ADT]. 2 Enter your security code. Example g ARM 3 Enter the number of the desired commands.
PAGE 43
SecurityPhone.book 43 ページ２００４年７月２１日水曜日午後６時５８分 Mute Security You can mute beep and announcement by selecting “Mute all sounds” through the function menu. Even if “Mute all sounds” is selected, alarm sound and emergency message are not muted. Base Unit 1 Press [FUNCTION/EDIT]. 2 Scroll to “Mute Security” by pressing [d] or [B], then press [g]. 3 Select “Mute all sounds” or “Sound all” by pressing [d] or [B]. Mute Security :Sound all g=Save 4 Press [g] (Save).
PAGE 44
SecurityPhone.book 44 ページ２００４年７月２１日水曜日午後６時５８分 Two Way Voice Feature The phone provides you with the Two Way Voice feature. This feature can be used only by an operator in a Customer Monitoring Center. This feature can help an operator to check a false alarm and respond in an event of emergency (panic). You can arm/disarm the security mode, if a Customer Monitoring Center operator is using the feature.
PAGE 45
SecurityPhone.book 45 ページ２００４年７月２１日水曜日午後６時５８分 Function Menu Table The phone provides you with the following Security menus (“Security” and “Mute Security”), which can be accessed by pressing [FUNCTION/EDIT] or [CONF/FUNCTION]. By pressing [ADT] in the standby mode, you can directly enter the Security submenu. Main menu Sub-menu I Sub-menu II Sub-menu III Telephone* *This menu is for the telephone and answering systems. Security (To be continued to the next page) ARM STAY p. 9 AWAY p.
PAGE 46
SecurityPhone.book 46 ページ２００４年７月２１日水曜日午後６時５８分 Function Menu Table Main menu Security (Continued from the previous page) Sub-menu I OTHER FUNCTIONS Sub-menu II FUNCTIONS A-D DEVICE COMMANDS USER CODES Sub-menu III FUNCTION A p. 23 FUNCTION B p. 23 FUNCTION C p. 23 FUNCTION D p. 23 ACTIVATE DEVICE p. 24 DEACTIV. DEVICE p. 24 ADD USER CODE p. 25 DEL. USER CODE p. 27 AUTHORITY LEVEL p. 28 ACCESS GROUP p. 30 RF USER NUMBER p. 32 PAGER ON/OFF p. 34 DATE/TIME p.
PAGE 47
SecurityPhone.book 47 ページ２００４年７月２１日水曜日午後６時５８分 If the Following Appear on Your Display... The following will be displayed when the phone needs your attention. Display message Cause & Remedy Telco Fault • A problem occurs on the telephone line. Call for service. SECURITYinactive Call ADT • A contract is not made or the phone has lost communication with the ADT security system. Call for a service. • [ADT] may have been pressed while the phone is in use. When the phone is not in use, try again.
PAGE 48
SecurityPhone.book 48 ページ２００４年７月２１日水曜日午後６時５８分 Troubleshooting If the handset display shows error messages, see “If the Following Appear on Your Display...” (p. 47) for the Cause & Remedy. Problem Cause & Remedy You cannot enter the function menu by pressing [ADT]. • [ADT] may have been pressed while the phone is in use. When the phone is not in use, try again. The phone does not sound alarm, when the system is armed. • Check the settings.
PAGE 49
SecurityPhone.book 49 ページ２００４年７月２１日水曜日午後６時５８分 TELEPHONE/MODEM INTERFACE FCC Part 68 This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested. This equipment uses the following USOC jack: RJ31X This equipment may not be used on telephone-company-provided coin service.
PAGE 50
SecurityPhone.book 50 ページ２００４年７月２１日水曜日午後６時５８分 Industrie Canada AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
PAGE 51
SecurityPhone.book 51 ページ２００４年７月２１日水曜日午後６時５８分 LIMITATIONS OF THIS SYSTEM WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons.
PAGE 52
SecurityPhone.book • • • • 52 ページ２００４年７月２１日水曜日午後６時５８分 Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection performance can decrease.
PAGE 53
SecurityPhone.book 53 ページ２００４年７月２１日水曜日午後６時５８分 The Parties’ obligations under this limited warranty shall be limited to the repair or replacement of any warranted parts found by the Parties to be defective in the Product, or, in the Parties’ sole discretion, the replacement of the Product found by the Parties to be defective.
PAGE 54
SecurityPhone.book 54 ページ２００４年７月２１日水曜日午後６時５８分 THE PARTIES DO NOT MAKE ANY CLAIMS OR WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE PRODUCT’S POTENTIAL, ABILITY OR EFFECTIVENESS TO DETECT, MINIMIZE, OR IN ANYWAY PREVENT DEATH, PERSONAL INJURY, PROPERTY DAMAGE OR LOSS OF ANY KIND WHATSOEVER. THE PARTIES ARE NOT RESPONSIBLE FOR ANY DEATH, PERSONAL INJURY, DAMAGE OR LOSS OR THEFT RELATED TO THE PRODUCT OR ITS USE OR FOR ANY HARM, WHETHER PHYSICAL OR MENTAL RELATED THERETO.
PAGE 55
SecurityPhone.book 55 ページ２００４年７月２１日水曜日午後６時５８分 RIGHTS UNDER STATE, PROVINCIAL, OR FEDERAL LAWS AND WHERE THE WHOLE OR ANY PART OF ANY ITEM OF THｓIS LIMITED WARRANTY IS PROHIBITED BY SUCH LAWS, IT SHALL BE DEEMED NULL AND VOID, BUT THE REMAINDER OF THE LIMITED WARRANTY SHALL REMAIN IN EFFECT.
PAGE 56
SecurityPhone.book 56 ページ２００４年７月２１日水曜日午後６時５８分 ADT Security Services Warning Statement “Neither Panasonic Communications Co., Ltd. (PCC) nor Matsushita Electric Corporation of America (MECA) is in any way affiliated with, or responsible for the acts or omissions of, ADT Security Services, Inc. (ADT).