Datasheet

HE-V
2
ds_61C06_0001_en_hev: 270213J
RATING
1. Coil data
2. Specifications
Notes:
*1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load.
*2. Wave is standard shock voltage of 1.250s according to JEC-212-1981
*3. Coil holding voltage is the coil voltage after 100 ms following application of the nominal coil voltage.
*4. The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. Refer to usage, transport and storage
conditions in “NOTES” on page 5
Nominal coil
voltage
Pick-up voltage
(at 20C 68F)
(Initial)
Drop-out voltage
(at 20C 68F)
(Initial)
Nominal operating
current
[10%] (at 20C 68F)
Coil resistance
[10%] (at 20C 68F)
Nominal operating
power
Max. applied voltage
(at 55C 131F)
6V DC
70%V or less of
nominal voltage
5%V or more of
nominal voltage
320mA 18.8
1,920mW
110%V of
nominal voltage
9V DC 213mA 42.2
12V DC 160mA 75.0
15V DC 128mA 117.0
24V DC 80mA 300.0
Characteristics Item Specifications
Contact
Arrangement 2 Form A
Contact material AgNi type
Contact resistance (Initial)
Max. 100 m (By voltage drop 6 V DC 1 A),
Max. 3 m (By voltage drop 6 V DC 20 A, Reference value)
Rating
Contact rating (Resistive load)
20 A 800 VDC (at each 1 Form A contact connected in series),
20 A 400 VDC (at 1 Form A contact only)
Max. switching voltage 1,000 V DC
Max. switching current 20 A
Min. switching capacity (Reference value)*
1
100 mA 5 V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 1,000M (at 1,000V DC) Measurement at same location as “Breakdown voltage” section.
Short current (Initial) Max. 300 A 1 ms (Reference value)
Breakdown
voltage (Initial)
Between open contacts 2,000 Vrms for 1 min. (Detection current: 10 mA)
Between contact sets 4,000 Vrms for 1 min. (Detection current: 10 mA)
Between contact and coil 5,000 Vrms for 1 min. (Detection current: 10 mA)
Surge breakdown voltage*
2
(Between contact and coil) (Initial)
Min. 10,000 V
Coil temperature rise value
Max. 75C 135F (By resistive method, contact carrying current: 20A,
100%V of nominal coil voltage at 55C 131F.)
Max. 45C 113F (By resistive method, contact carrying current: 20A,
60%V of nominal coil voltage at 85C 185F.)
Coil holding voltage*
3
33 to 110%V (Contact carrying current: 20A, at 55C 131F),
33 to 60%V (Contact carrying current: 20A, at 85C 185F)
Operate time (at 20C 68F) Max. 30 ms (nominal coil voltage, without bounce)
Release time (at 20C 68F) Max. 10 ms (nominal coil voltage) (without diode)
Mechanical
characteristics
Shock
resistance
Functional Min. 98 m/s
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10 s)
Destructive Min. 980 m/s
2
(Half-wave pulse of sine wave: 6 ms)
Vibration
resistance
Functional 10 to 55 Hz at double amplitude of 1.0 mm (Detection time: 10 s)
Destructive 10 to 55 Hz at double amplitude of 1.5 mm
Expected life Mechanical life Min. 10
6
(at 180 times/min.)
Conditions
Conditions for operation, transport and
storage*
4
Ambient temperature:
–40 to +55C –40 to +131F (When coil holding voltage is 33% to 110% of nominal coil voltage)
–40 to +85C –40 to +185F (When applied coil hold voltage is 33% to 60% of nominal coil voltage)
Humidity: 5 to 85% R.H. (Not freezing and condensing)
Max. operating speed 6 times/min. (at nominal switching capacity ON : OFF = 1s : 9s)
Unit weight Approx. 120 g 4.23 oz