HDC-Z10000P-VQT3U98_mst.book 1 ページ ２０１１年１０月４日 火曜日 午後３時２分 Owner’s Manual High Definition Video Camera Model No. HDC-Z10000P Before connecting, operating or adjusting this product, please read the instructions completely. For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.
HDC-Z10000P-VQT3U98_mst.book 2 ページ ２０１１年１０月４日 火曜日 Dear customer, Date of Purchase Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. The serial number is on the tag located on the underside of your camera. Be sure to retain this manual as your convenient camera information source.
HDC-Z10000P-VQT3U98_mst.book 3 ページ ２０１１年１０月４日 火曜日 午後３時２分 THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
HDC-Z10000P-VQT3U98_mst.book 4 ページ ２０１１年１０月４日 火曜日 午後３時２分 AC adaptor This AC adaptor operates on AC between 110 V and 240 V. But ≥ In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power supply only. ≥ When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to suit the AC outlet configuration. ≥ When connecting to a supply of greater than AC 125 V, ensure the cord you use is suited to the voltage of the AC supply and the rated current of the AC adaptor.
HDC-Z10000P-VQT3U98_mst.book 5 ページ ２０１１年１０月４日 火曜日 午後３時２分 Warning Risk of fire, explosion and burns. Do not disassemble. Do not heat the batteries above the following temperatures or incinerate. Button-type battery 60 oC (140 oF) Battery pack 60 oC (140 oF) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
HDC-Z10000P-VQT3U98_mst.book 6 ページ ２０１１年１０月４日 火曜日 午後３時２分 IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
HDC-Z10000P-VQT3U98_mst.book 7 ページ ２０１１年１０月４日 火曜日 午後３時２分 Precautions USE & LOCATION WARNING ≥ TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee.
HDC-Z10000P-VQT3U98_mst.book 8 ページ ２０１１年１０月４日 ∫ Features This unit is a single body twin lens type 3D high-definition video camera. With the adoption of twin lens format, the convergence point can be adjusted within this unit, allowing to record natural and deep 3D video. (l 39) ∫ About the recording format for recording motion pictures You can record motion pictures with AVCHD recording formats using this unit. (l 36, 115) ≥ AVCHD 3D and AVCHD Progressive supported.
Parts identification and handling .......... 12 Power supply........................................... 17 Charging the battery ......................... 18 Inserting/removing the battery........... 19 Charging and recording time............. 20 Connecting to the AC outlet .............. 21 Preparation of SD cards .........................22 Cards that you can use with this unit .................................................... 22 Inserting/removing an SD card.......... 23 Turning the unit on/off........
HDC-Z10000P-VQT3U98_mst.book 10 ページ ２０１１年１０月４日 火曜日 午後３時２分 Editing Others With a PC ................................................. 93 What you can do with a PC............... 93 End User License Agreement ........... 95 Operating environment ..................... 97 Installation ....................................... 100 Connecting to a PC ......................... 102 About the PC display ...................... 103 Starting HD Writer XE 1.0 ...............
HDC-Z10000P-VQT3U98_mst.book 11 ページ ２０１１年１０月４日 火曜日 午後３時２分 Accessories Check the accessories before using this unit. Keep the accessories out of reach of children to prevent swallowing. Product numbers correct as of Oct. 2011. These may be subject to change.
HDC-Z10000P-VQT3U98_mst.book 12 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Parts identification and handling 1 23 4 5 13 6 14 7 8 9 10 11 12 15 16 17 1 Shoulder strap fixture 2 Sub zoom lever (l 48,126) ≥ This lever functions in the same manner as the zoom lever. 3 Sub recording start/stop button (l 33, 126) ≥ This button functions in the same manner as the recording start/stop button.
HDC-Z10000P-VQT3U98_mst.
HDC-Z10000P-VQT3U98_mst.book 14 ページ 44 45 ２０１１年１０月４日 火曜日 午後３時２分 46 47 48 49 50 51 52 53 54 55 56 60 61 62 57 58 59 44 LCD monitor extract part [PULL] (l 25) 45 LCD monitor (Touch screen) (l 26) 46 Shoulder strap fixture 47 Eye cup attachment part (l 15) 48 Eye cup (l 15) 49 Viewfinder (l 28) 50 Battery release button [PUSH] (l 19) 51 Battery holder (l 19) 52 DC input terminal [DC IN] (l 21) ≥ Do not use any other AC adaptors except the supplied one.
HDC-Z10000P-VQT3U98_mst.book 15 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ Adjust the length of the grip belt so that it fits your hand. 1, 2 Flip the belt cover and the belt. 3 Adjust the length. 4, 5 Replace the belt. ∫ Attaching the eye cup Attach by aligning the notch of the eye cup attachment part with the protrusion at the inside of the eye cup.
HDC-Z10000P-VQT3U98_mst.book 16 ページ ２０１１年１０月４日 火曜日 午後３時２分 ≥ When attaching the microphone holder and the microphone holder adaptor, be sure to tighten the screws firmly even though you might hear a squeaking sound. ∫ Attaching the tripod ≥ There are tripod mounting holes that are compatible with 1/4-20UNC and 3/8-16UNC screws. Use the size that matches the diameter of the tripod’s fixing screw. ≥ If you attach a tripod which has 5.5 mm (0.22 q) screw or larger, it may damage this unit.
HDC-Z10000P-VQT3U98_mst.book 17 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Power supply ∫ About batteries that you can use with this unit The battery that can be used with this unit is CGA-D54. It has been found that counterfeit battery packs which look very similar to the genuine product are made available to purchase in some markets. Some of these battery packs are not adequately protected with internal protection to meet the requirements of appropriate safety standards.
HDC-Z10000P-VQT3U98_mst.book 18 ページ ２０１１年１０月４日 火曜日 午後３時２分 Charging the battery When this unit is purchased, the battery is not charged. Charge the battery fully before using this unit for the first time. Important: ≥ Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do not use the AC cable from other equipment with this unit. ≥ It is recommended to charge the battery in a temperature between 10 oC to 30 oC (50 °F to 86 °F).
HDC-Z10000P-VQT3U98_mst.book 19 ページ ２０１１年１０月４日 火曜日 午後３時２分 Inserting/removing the battery Install the battery by inserting it in the direction shown in the figure. Removing the battery Make sure that the power switch is set to OFF and the status indicator is turned off, and then remove by holding onto it taking care not to drop. (l 24) While pushing the PUSH button, remove the battery. A Insert the battery until it clicks and locks.
HDC-Z10000P-VQT3U98_mst.book 20 ページ ２０１１年１０月４日 火曜日 午後３時２分 Charging and recording time ∫ Charging/Recording time ≥ Temperature: 25 oC (77 oF)/humidity: 60%RH ≥ When using the viewfinder (times in parentheses are when using the LCD monitor) Battery model number [Voltage/Capacity (minimum)] Charging time Maximum 3D/2D Recording continuously Recording format recordable Mode time 3D Recording Mode Supplied battery/ CGA-D54 (optional) [7.
HDC-Z10000P-VQT3U98_mst.book 21 ページ ２０１１年１０月４日 火曜日 午後３時２分 Connecting to the AC outlet Important: ≥ Use the supplied AC adaptor. Do not use the AC adaptor of another device. ≥ Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do not use the AC cable from other equipment with this unit. 1 Connect the AC cable to the AC adaptor and the AC outlet. ≥ Use the AC cable (K2CB2CB00022; supplied) dedicated for the AC adaptor.
HDC-Z10000P-VQT3U98_mst.book 22 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Preparation of SD cards The unit can record motion pictures or still pictures to an SD card. This unit (an SDXC compatible device) is compatible with SD Memory Cards, SDHC Memory Cards and SDXC Memory Cards. When using an SDHC Memory Card/SDXC Memory Card with other equipment, check the equipment is compatible with these Memory Cards.
HDC-Z10000P-VQT3U98_mst.book 23 ページ ２０１１年１０月４日 火曜日 午後３時２分 Inserting/removing an SD card When using an SD card not from Panasonic, or one previously used on other equipment, for the first time on this unit, format the SD card. (l 34) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored. Caution: Check that the access lamp has gone off. Access lamp A ≥ When this unit is accessing the SD card, the access lamp lights up.
HDC-Z10000P-VQT3U98_mst.book 24 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Turning the unit on/off Set the power switch to ON while pressing the lock release button B to turn on the unit. To turn off the unit Set the power switch to OFF while pressing the lock release button. The status indicator goes off. A The status indicator lights on. ≥ To turn on the unit again after the [ECONOMY (BATT)] or [ECONOMY (AC)] is activated, set the power switch to OFF once, and then to ON again.
HDC-Z10000P-VQT3U98_mst.book 25 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Using the LCD monitor/Viewfinder The viewfinder is turned off and the LCD monitor is turned on when the LCD monitor is extracted. The viewfinder is turned on when the LCD monitor is retracted. It is possible to check the images recorded during 3D recording or scenes recorded in 3D as 3D when LCD monitor is used.
HDC-Z10000P-VQT3U98_mst.book 26 ページ ２０１１年１０月４日 火曜日 午後３時２分 How to use the touch screen You can operate by directly touching the LCD monitor (touch screen) with your finger. It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate with your fingers. ∫ Touch Touch and release the touch screen to select icon or picture. ≥ Touch the center of the icon. ≥ Touching the touch screen will not operate while you are touching another part of the touch screen.
HDC-Z10000P-VQT3U98_mst.book 27 ページ ２０１１年１０月４日 火曜日 午後３時２分 LCD monitor adjustment ≥ These settings will not affect the images actually recorded. [POWER LCD] This makes it easier to view the LCD monitor in bright places including outdoors. Select the menu. (l 30) MENU : [SW & DISP SETUP] # [POWER LCD]# [ON] ≥ It cannot be set while in 3D is displayed. ≥ When the AC adaptor is in use, [POWER LCD] is set to [ON] automatically. ≥ Recordable time with the battery is shortened when the LCD is made brighter.
HDC-Z10000P-VQT3U98_mst.book 28 ページ ２０１１年１０月４日 火曜日 午後３時２分 Viewfinder adjustment ≥ These settings will not affect the images actually recorded. Adjusting the field of view It adjusts the field of view to show the image on the viewfinder clearly. 1 Adjust the viewfinder according to the position that is easy to view. ≥ Be careful not to trap your fingers when moving the finder. ≥ The viewfinder can be lifted vertically up to approximately 90o. ≥ Retract the LCD monitor and turn on the viewfinder.
HDC-Z10000P-VQT3U98_mst.book 29 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Setting date and time When the unit is turned on for the first time, a message asking you to set the date and time will appear. Select [YES] and perform steps 2 to 3 below to set the date and time. 1 Select the menu. (l 30) MENU 2 : [OTHER FUNCTION] # [CLOCK SET] # [YES] Touch the date or time to be set, then set the desired value using / . ≥ The year can be set between 2000 and 2039.
HDC-Z10000P-VQT3U98_mst.book 30 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Using the menu screen MENU 1 2 Press the MENU button 3 Touch the submenu B. MENU . Touch the desired item to enter the setting. 5 Touch [EXIT] to exit the menu setting. Touch the top menu A. ≥ Next (Previous) page can be displayed by touching / .
HDC-Z10000P-VQT3U98_mst.book 31 ページ ２０１１年１０月４日 火曜日 午後３時２分 Preparation Using with the wireless remote control Select the menu. MENU : [OTHER FUNCTION] # [REMOTE CONTROL] # [ON] 1 2 3 4 START/ STOP /VOL DATE/TIME EXT DISPLAY SEARCH PLAY SEARCH STILL ADV PAUSE STILL ADV SKIP STOP 5 6 7 8 9 9 Date/time button [DATE/TIME] (l 124) 10 Menu button [MENU]* 11 OK button [OK] * means that these buttons function in the same manner as the corresponding buttons on the unit.
HDC-Z10000P-VQT3U98_mst.book 32 ページ CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. ２０１１年１０月４日 火曜日 午後３時２分 Replace battery with Panasonic PART NO. CR2025 only. Use of another battery may present a risk of fire or explosion. Caution: Battery may explode if mistreated. Dispose of used battery promptly. Keep away from children.
HDC-Z10000P-VQT3U98_mst.book 33 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Before recording ∫ Basic camera positioning Normal recording Low-angle recording ≥ For easier low-angle recording, the sub recording start/stop button and the sub zoom lever can be used. ≥ Put your hand through the grip belt and hold the unit with both hands.
HDC-Z10000P-VQT3U98_mst.book 34 ページ ２０１１年１０月４日 火曜日 午後３時２分 ≥ When recording, make sure your footing is stable and there is no danger of colliding with another person or object. ≥ Hold the eye cup of the viewfinder as close as possible to your right eye. ≥ Adjust the angle of the LCD monitor according to the position in which the unit is held. ≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it will become dark in the recording.
HDC-Z10000P-VQT3U98_mst.book 35 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Selecting a media to record [SD CARD 1] and [SD CARD 2] can be selected separately to record motion pictures or still pictures. 1 Select the menu. MENU 2 : [SW & DISP SETUP] # [MEDIA SELECT] # [YES] Touch the media to record motion pictures or still pictures. ≥ The media is selected separately to motion pictures or still pictures is highlighted in yellow. 3 Touch [ENTER].
HDC-Z10000P-VQT3U98_mst.book 36 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Recording motion pictures You can record life-like and powerful 3D full high definition quality video. 3D video * The image is an illustration. ≥ This unit can record a 3D full high definition quality video in AVCHD 3D recording format. ≥ Refer to page 91 if the 3D full high definition quality video is viewed with 3D compatible TV. ≥ It is possible to record while checking the 3D video when the LCD monitor is used.
HDC-Z10000P-VQT3U98_mst.book 37 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ Screen indications in the Recording Mode (When in 3D Recording Mode) (When in 2D Recording Mode) TC 00:00:00:00 R 1h20m TC 00:00:00:00 R 1h20m 60 i 60 i 2.9 TC 00:00:00:00 (White) Counter display (l 63) Media where the motion picture is recorded (l 35) R 1h20m Approximate remaining recordable time ≥ When the remaining time is less than 1 minute, R 0h00m flashes red. 3D recording icon *1 *2 60i C10*1 3D 2.
HDC-Z10000P-VQT3U98_mst.book 38 ページ ２０１１年１０月４日 火曜日 午後３時２分 To ensure that the 3D video can be safely viewed, pay attention to the following points when recording. ≥ Do not get too close to the subject. (Use the 3D guide display as guidance. (l 41))* * It is possible to get close to approximately 45 cm (1.5 feet) when the 3D macro is used. (l 73) ≥ When moving the unit as you record, move it slowly. ≥ Try to hold the unit as steady as possible when recording while riding in a vehicle or walking.
HDC-Z10000P-VQT3U98_mst.book 39 ページ ２０１１年１０月４日 火曜日 午後３時２分 Convergence point adjustment ∫ About the convergence point Convergence point is a position that becomes the reference plane of the 3D image. When viewing the 3D image, a subject located closer than the convergence point is displayed in front of the screen, and a subject located farther than the convergence point is displayed behind the screen.
HDC-Z10000P-VQT3U98_mst.book 40 ページ 2 ２０１１年１０月４日 火曜日 午後３時２分 Rotate the CONV. dial to adjust the convergence point. ≥ This can be set between C00 and C99. Position of the convergence point will be set further when the number is larger. ≥ The subject at the position of the convergence point will not shoot out or recess from the screen. (It is seen as CONV. same as the 2D image) ≥ Adjust by checking on the 3D image or 3D guide display on the LCD monitor.
HDC-Z10000P-VQT3U98_mst.book 41 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ 3D guide display The 3D guide display is a guideline of distance between the subject and this unit to effectively reproduce the subject as a 3D image. ≥ The values of the 3D guide display will change according to the zoom magnification and convergence point settings. 3D GUIDE 3D GUIDE button 3D 0.9 - ∞ ft Press the button to switch on/off of the 3D guide display. A 3D guide display 2.
HDC-Z10000P-VQT3U98_mst.book 42 ページ ２０１１年１０月４日 火曜日 午後３時２分 To record in such a way that 3D image of the subject can be effectively reproduced We recommend that you record with the subject positioned within the range of the 3D guide display. 3D guide display A Minimum distance on 3D guide display B Maximum distance on 3D guide display ≥ When the subject is out of the range of the 3D guide display, the 3D guide display is displayed in red.
HDC-Z10000P-VQT3U98_mst.book 43 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ 3D Fine The position, focus, and iris of the left and right lenses can be finely adjusted. ≥ Set [3D/2D REC MODE] to [3D]. (l 36) ≥ Connect this unit to the 3D compatible television using a HDMI cable (optional). (l 88) 1 Select the menu. MENU 2 : [OTHER FUNCTION] # [3D FINE] # [YES] Touch the desired setting item to adjust.
HDC-Z10000P-VQT3U98_mst.book 44 ページ ２０１１年１０月４日 火曜日 午後３時２分 Focus adjustment 1 Touch r/s to adjust the focus. r: To focus on a close subject s: To focus on a faraway subject ≥ It will return to default setting when [Reset] is touched. ≥ Focus Assist will operate when [FA] is touched, and the part that is focused will be displayed in red. Touch [FA] again to cancel the operation. ≥ Image of the left and right lenses will switch every time the lens switch icon is touched.
HDC-Z10000P-VQT3U98_mst.book 45 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Recording still pictures 3D still pictures and 2D still pictures in [ 2.1 M (1920k1080)] (16:9) are recorded for 3D Recording Mode, and 2D still pictures in [ 3 M (2304k1296)] (16:9) are recorded for 2D Recording Mode. 1 Change the mode to . ≥ Extract the LCD monitor. 2 Press the button. ≥ Remaining number of recordable pictures is displayed while still pictures are being recorded.
HDC-Z10000P-VQT3U98_mst.book 46 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Intelligent Auto Mode/Manual Mode MANU iA/MANU switch Slide the switch to change the Intelligent Auto Mode/Manual Mode. ≥ MNL is displayed in the Manual Mode. ≥ The following modes appropriate for the condition are set just by pointing the unit to what you want to record in the Intelligent Auto Mode. Mode Effect Portrait Faces are detected and focused automatically, and the brightness is adjusted so it is recorded clearly.
HDC-Z10000P-VQT3U98_mst.book 47 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ Intelligent Auto Mode When switching to Intelligent Auto Mode, the Auto White Balance and Auto Focus operate and automatically adjust the color balance and focusing. Depending on the brightness of the subject etc., the aperture and shutter speed are automatically adjusted for an optimum brightness. ≥ Color balance and focus may not be adjusted automatically depending on light sources or scenes. If so, manually adjust these settings.
HDC-Z10000P-VQT3U98_mst.book 48 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Zoom in/out function It can be zoomed up to 10k for the 3D Recording Mode, and up to 12k for the 2D Recording Mode. ≥ It can zoom up to 23k when the [i.Zoom] is set to [ON] during the 2D Recording Mode. (l 118) ≥ Zoom magnification can be checked in the screen display of Z00 to Z99. The value gets larger when zoomed in, and the value gets smaller when zoomed out. 99 is displayed during the i.Zoom.
HDC-Z10000P-VQT3U98_mst.book 49 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ About the zoom speed ≥ The zoom speed will vary depending on how far the zoom lever is pressed or how fast the zoom ring is rotated. ≥ Zoom speed of the sub zoom lever will vary depending on the setting of [SUB ZOOM]. (l 126) ≥ The zoom speed does not vary when operating with the wireless remote control. ≥ If you take your finger off the zoom lever during zoom operation, the operation sound may be recorded.
HDC-Z10000P-VQT3U98_mst.book 50 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Image Stabilizer Function Use the image stabilizer to reduce the effects of shake during recording. This unit is equipped with Optical Image Stabilizer in the 3D Recording Mode. This unit is equipped with Hybrid Optical Image Stabilizer in the 2D Recording Mode. Hybrid Optical Image Stabilizer is a hybrid of optical and electrical image stabilizer. O.I.S.
HDC-Z10000P-VQT3U98_mst.book 51 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Focus Perform focus adjustments using the focus ring. If auto focusing is difficult due to the conditions, then use Manual Focus. ≥ Switch to Manual Mode. (l 46) A FOCUS A/M/¶ button B Focus ring FOCUS A/M/∞ 1 Press the FOCUS A/M/¶ button to switch to Manual Focus. ≥ It will switch to MF from AF. 2 Adjust the focus by rotating the focus ring. ≥ The focus value can be set from MF00 (focus distance: approximately 30 cm (0.
HDC-Z10000P-VQT3U98_mst.book 52 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording White Balance Automatic White Balance function may not reproduce natural colors depending on the scenes or lighting conditions. If so, you can adjust the White Balance manually. Switch the modes of White Balance by pressing the W.B. button. A W.B. button W.B. ≥ Select the optimal mode by confirming the color on the screen. Icon Mode ATW Settings It will automatically adjust in accordance with the recording condition.
HDC-Z10000P-VQT3U98_mst.book 53 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ To set the White Balance in accordance to the recording scene 1 Fill the screen with a white subject 2 Press the W.B. button to display Ach. ≥ When the operation icon is displayed and Ach is touched, it will switch to Bch . (l 78) 3 Keep on pressing the W.B. button to start the White Balance adjustment ≥ The screen goes dark momentarily, “WB SET OK” is displayed, and the adjustment ends.
HDC-Z10000P-VQT3U98_mst.book 54 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Iris adjustment Perform Iris/Gain adjustments using the iris ring. Adjust it when the screen is too bright or too dark. MNL F4.0 IRIS A/M A Gain value B Iris value C Auto iris icon* * It is displayed in Auto Iris Mode. 1 IRIS A/M button 2 Iris ring ≥ Switch to Manual Mode. (l 46) 1 Press the IRIS A/M button to switch to Manual Iris Mode. ≥ disappears. ≥ The gain is displayed in dB.
HDC-Z10000P-VQT3U98_mst.book 55 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ Adjusting brightness during the Auto Iris Mode ≥ Switch to Manual Mode. (l 46) 1 Select the menu. MENU 2 3 : [CAMERA SETUP] # [AUTO IRIS LEVEL] Touch / to adjust settings. Touch [EXIT] to complete the setting. Utilizing the USER button It is convenient to use following functions of the USER button when it is set to Manual Iris. ≥ Please refer to page 67 for details about setting the USER button.
HDC-Z10000P-VQT3U98_mst.book 56 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Manual shutter speed Adjust the shutter speed when recording fast-moving subjects. ≥ Switch to Manual Mode. (l 46) 1 Touch the LCD monitor to display the operation icons and touch the SHTR . (l 78) 2 Touch / to adjust settings. ≥ When [AUTO] is touched, the shutter speed is set automatically. ≥ Touch SHTR to complete the adjustment. Shutter speed: 1/60 to 1/2000 ≥ It will be 1/30 to 1/2000 when [AUTO SLOW SHTR] is set to [ON].
HDC-Z10000P-VQT3U98_mst.book 57 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Audio Input This unit can record audio in 5.1 ch or 2 ch. When recording in 2 ch, it is possible to switch between built-in microphone, external microphone, or connected audio equipment for each channel. Microphone setup Recording setting of the built-in microphone can be adjusted. Select the menu. MENU : [RECORD SETUP] # [MIC SETUP] # desired setting [SURROUND]: Sound is recorded with 5.1 ch surround microphone.
HDC-Z10000P-VQT3U98_mst.book 58 ページ ２０１１年１０月４日 火曜日 午後３時２分 Audio recording Switches the sound quality for the audio recording. Select the menu. MENU : [RECORD SETUP] # [AUDIO REC] # desired setting : Records in Dolby Digital. [LPCM]: Records in uncompressed LPCM. ≥ It may not be able to play back on other devices when set to [LPCM]. ≥ [AUDIO REC] will be set to when the [REC FORMAT] is set to [HA] or [HE], and the setting cannot be changed.
HDC-Z10000P-VQT3U98_mst.book 59 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ Using an external microphone or audio equipment ≥ Set [MIC SETUP] to [2ch]. (l 57) 1 Connect an external microphone or audio equipment to AUDIO INPUT1,2 terminals (XLR 3-pin). (l 15) 2 Use INPUT1,2 (LINE/MIC) switches to switch the connected audio input signal. LINE: audio equipment is connected Input level is 0 dBu. MIC: an external microphone is connected Input level is -50 dBu. ≥ When [EXT. MIC GAIN1] or [EXT.
HDC-Z10000P-VQT3U98_mst.book 60 ページ ２０１１年１０月４日 火曜日 午後３時２分 To remove the external microphone, etc., from the audio input terminals 1, 2 (XLR 3 pin) Remove while pushing on the PUSH section of the audio input terminals 1, 2 (XLR 3 pin). ≥ Set the input signal to built-in microphone by switching the CH1, CH2 switches to INT (L) or INT (R) after removing the external microphone. Audio will not be recorded when motion picture is recorded without switching.
HDC-Z10000P-VQT3U98_mst.book 61 ページ ２０１１年１０月４日 火曜日 午後３時２分 Adjusting the audio input level ∫ Adjusting the input level of the built-in microphone (5.1 ch) ≥ Set the [MIC SETUP] to anything other than [2ch]. (l 57) 1 Select the menu. MENU : [RECORD SETUP] # [5.1ch MIC LEVEL] # desired setting [AUTO]: [SET]/[SETr 2 ALC is activated, and the recording level is adjusted automatically. ]: (When [SET]/[SETr Touch / input level. The desired recording level can be set.
HDC-Z10000P-VQT3U98_mst.book 62 ページ ２０１１年１０月４日 火曜日 午後３時２分 Adjusting the input level of the built-in microphone (5.1 ch) using the operation icons ≥ Set the [MIC SETUP] to anything other than [2ch]. (l 57) ≥ Set [5.1ch MIC LEVEL] to [SET]/[SETr ]. (l 61) 1 2 3 Display the operation icons and touch the Touch / to adjust settings. Touch to complete the setting. icon (l 78) ∫ Adjusting the input level of the built-in microphone (2 ch), external microphone or audio device ≥ Set [MIC SETUP] to [2ch].
HDC-Z10000P-VQT3U98_mst.book 63 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Counter display You can change a counter display that indicates how much time has elapsed during recording or playback. COUNTER COUNTER button Each time you press the button, the counter display changes. Time Code # User Information # Recording Counter # Setting canceled Counter display Indications Time Code TC 00:00:00:00 or TC 00:00:00.00 ≥ Display will change depending on the setting of the [TC MODE].
HDC-Z10000P-VQT3U98_mst.book 64 ページ ２０１１年１０月４日 火曜日 午後３時２分 Setting the Time Code Time code will display the recording time in hours, minutes, seconds, and frames. TC 00:00:00:00 (hour : minute : second : frame [NDF]) TC 00:00:00.00 (hour : minute : second . frame [DF]) ≥ The frame (Number of frames counted every second) will vary depending on the [REC FORMAT] setting.
HDC-Z10000P-VQT3U98_mst.book 65 ページ ２０１１年１０月４日 火曜日 午後３時２分 [TC PRESET] You can set the initial time code. 1 Select the menu. MENU 2 : [RECORD SETUP] # [TC PRESET] # [YES] Touch the item to set and change with / . ≥ It will be set to 00h00m00s00f when the RESET button is pressed. ≥ “h” is an abbreviation for hour, “m” for minute, “s” for second and “f” for frame. 3 Touch [ENTER]. ≥ Touch [EXIT] to complete the setting.
HDC-Z10000P-VQT3U98_mst.book 66 ページ ２０１１年１０月４日 火曜日 午後３時２分 Setting the Recording Counter Recording Counter will display the recording time in seconds. 00:00:00 (hour : minute : second (When [REC COUNTER] is set to [TOTAL])) SCN 00:00:00 (hour : minute : second (When [REC COUNTER] is set to [SCENE])) [REC COUNTER] Select the counting method during the recording. MENU : [SW & DISP SETUP] # [REC COUNTER] # desired setting [TOTAL]: The count continues to increase until the Recording Counter is resetted.
HDC-Z10000P-VQT3U98_mst.book 67 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording USER button Each of the USER button can register one function from the 18 available functions. ≥ There are three USER buttons (USER1 to USER3) on the main body and four USER button icons USER4 to USER7 displayed on the LCD monitor. Setting the USER button 1 Select the menu. MENU 2 : [SW & DISP SETUP] # [USER BUTTON SETUP] Touch the USER button you wish to set.
HDC-Z10000P-VQT3U98_mst.book 68 ページ ２０１１年１０月４日 火曜日 午後３時２分 Using the USER button To use the set USER button, press USER1 to USER3 button or touch the USER4 to USER7 button icon displayed when you touch the LCD monitor. (When you use the USER1 to USER3) (When you use the [USER4] to [USER7]) (In Recording Mode) SCN1 SCN2 SCN3 SCN4 SCN5 SCN6 USER1 USER2 USER3 USER4 ATW USER5 Conv.R USER6 3D USER7 REC.C (In Playback Mode) USER4 ATW USER5 Conv.R USER6 3D USER7 REC.
HDC-Z10000P-VQT3U98_mst.book 69 ページ ２０１１年１０月４日 火曜日 午後３時２分 Functions of the USER button ∫ List of USER button function Icon Item Function [P.AF]*1 [PUSH AF] [B.Light]*1 [BACKLIGHT] Backlight Compensation [S.Light]*1 [SPOTLIGHT] Spotlight [B.FD]*1 [BLACK FADE] Black Fade [W.FD]*1 [WHITE FADE] White Fade [ATW]*1 [ATW] ATW [ATW.L]*1 [ATW LOCK] ATW Lock [FA]*1 [FA] Focus Assist [D.ZM]*1 [D.
HDC-Z10000P-VQT3U98_mst.book 70 ページ ２０１１年１０月４日 火曜日 午後３時２分 Spotlight Switches to automatic iris control for spotlight. Very bright object is recorded clearly. ≥ appears when it is set. ≥ It will return to standard Auto Iris Mode ( ) when it is canceled. (l 54) Black Fade Fade in/fade out effect (black) can be added to the video and audio that is being recorded. Press USER button or touch USER button icon in the recording screen.
HDC-Z10000P-VQT3U98_mst.book 71 ページ ２０１１年１０月４日 火曜日 午後３時２分 ATW Lock The White Balance can be changed to ATW Lock. (l 52) ≥ It will return to ATW when canceled. ≥ This cannot be set when the White Balance is set to anything other than ATW. Focus Assist The in-focus area is displayed in red. ≥ The red display does not appear on the images actually recorded. ≥ The red display does not appear on TV. Digital Zoom Press USER button or touch USER button icon in the recording screen.
HDC-Z10000P-VQT3U98_mst.book 72 ページ ２０１１年１０月４日 火曜日 午後３時２分 Histogram A graph with brightness as horizontal axis and number of pixels at that brightness as vertical axis is displayed. It is possible to determine the exposure of the whole image by looking at the distribution in the graph. ≥ To adjust the brightness, refer to page 54. 3D Display Switches the display method of the 3D video. ≥ These settings will not affect the images actually recorded. ≥ Set [3D/2D REC MODE] to [3D].
HDC-Z10000P-VQT3U98_mst.book 73 ページ ２０１１年１０月４日 火曜日 午後３時２分 3D Macro It will go back to ALL display when the recording is started by switching to the recording mode. ≥ Set [3D/2D REC MODE] to [3D]. (l 36) ≥ is displayed. ≥ Canceling returns the convergence point to the original position. ≥ The setting is canceled in following cases: j If you adjust the CONV. dial (l 39) j If you reset the Convergence point ≥ Stop the recording when you feel fatigue, discomfort, or otherwise strange while recording.
HDC-Z10000P-VQT3U98_mst.book 74 ページ ２０１１年１０月４日 火曜日 午後３時２分 Last Scene Delete The motion picture recorded last can be deleted. Deleted scenes cannot be restored. 1 2 Press USER button or touch USER button icon in the recording screen. Touch [YES]. ≥ It will return to recording screen without deleting by touching [NO].
HDC-Z10000P-VQT3U98_mst.book 75 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Useful functions DISP/MODE CHK A B C D DISP/MODE CHK button ZEBRA button QUICK START button BARS button ZEBRA BARS QUICK START Quick Start 1 Press and hold down the QUICK START button until the display on the LCD monitor/ viewfinder disappears. The quick start lamp E flashes green and the unit goes into Quick Start Standby Mode. 2 Press the QUICK START button.
HDC-Z10000P-VQT3U98_mst.book 76 ページ ２０１１年１０月４日 火曜日 午後３時２分 Zebra ZEBRA button It will switch between the zebra display and the marker display every time the button is pressed. Zebra 1 # Zebra 2* # Marker* # setting canceled * It is not displayed when the [ZEBRA DETECT 2]/[MARKER] is set to [OFF]. (l 123) Zebra display: Parts where white saturation (color saturation) is likely to occur (extremely brightly lit or shiny parts) are displayed with diagonal lines (zebra pattern).
HDC-Z10000P-VQT3U98_mst.book 77 ページ ２０１１年１０月４日 火曜日 午後３時２分 Switching the screen indications/mode information display DISP/MODE CHK button All the screen display other than the Counter display, Marker, and Safety Zone will disappear when this button is pressed. (l 132) ≥ To cancel, press the DISP/MODE CHK button again.
HDC-Z10000P-VQT3U98_mst.book 78 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Using of Operation Icons You can use convenient functions just by the easy operation of touching the screen. 1 Touch the LCD monitor in the recording screen or playback screen. SCN1 SCN2 SCN3 SCN4 SCN5 SCN6 ATW ≥ The operation icons are displayed. Conv.R 2 REC.C 3D Touch an operation icon. ≥ The following function is available. Refer to the respective pages for the operation. SCN1 , SCN2 etc.
HDC-Z10000P-VQT3U98_mst.book 79 ページ ２０１１年１０月４日 火曜日 午後３時２分 Playback Motion picture/Still picture playback 1 2 3 Change the mode to . Touch the play mode select icon A. 1 2 3 4 5 6 7 8 9 Select the [MEDIA] and [VIDEO/ PICTURE] you wish to play back. ≥ Touch [ENTER]. ≥ An icon is displayed in the thumbnail display when video item is touched. ( , 2D ) 4 Touch the scene or the still picture to be played back.
HDC-Z10000P-VQT3U98_mst.book 80 ページ ２０１１年１０月４日 Motion picture playback Playback/Pause Rewind playback Fast forward playback Stops the playback and shows the thumbnails. Display the direct playback bar (l 83) 1/;: 6: 5: ∫: : 火曜日 午後３時２分 Still picture playback 1/;: 2;: ;1: ∫: Slide show (playback of the still pictures in numerical order) start/ pause. Plays back the previous picture. Plays back the next picture. Stops the playback and shows the thumbnails.
HDC-Z10000P-VQT3U98_mst.book 81 ページ ２０１１年１０月４日 火曜日 午後３時２分 Motion picture compatibility ≥ This unit is based on AVCHD 3D/AVCHD Progressive/AVCHD. AVCHD 3D video ≥ Video signals for the AVCHD 3D that can be played back with this unit are 1920k1080/ 60i and 1920k1080/24p. ≥ Do not delete or edit the 3D video recorded on the SD card with this unit using anything other than AVCHD 3D compatible equipment (such as conventional AVCHD compatible equipment). 3D video in the SD card will be converted to 2D video.
HDC-Z10000P-VQT3U98_mst.book 82 ページ ２０１１年１０月４日 火曜日 午後３時２分 Motion picture playback using operation icon For details on the basic playback operations, refer to page 79. Playback operation Playback display Fast forward/ rewind playback During Playback Press the : or 9 button during playback. (Operation is possible with the remote control only.) Skip playback (to the start of a scene) Slow-motion Playback During Pause Frame-by-frame playback The motion picture is advanced one frame at a time.
HDC-Z10000P-VQT3U98_mst.book 83 ページ Playback operation ２０１１年１０月４日 Playback display 火曜日 午後３時２分 Operating steps 1) During Playback Direct playback Touch 1 to display the direct playback bar A. 2) Touch the direct playback bar or slide it while touching. ≥ The playback pauses temporarily and skips to the position touched or slid to while touching. ≥ Playback will start by releasing your touching or sliding finger. ≥ Touch 2 to display the operation icon.
HDC-Z10000P-VQT3U98_mst.book 84 ページ ２０１１年１０月４日 火曜日 午後３時２分 Playback Useful functions Creating still picture from motion picture A single frame from the recorded motion picture can be saved as a still picture. 3D still picture and 2D still picture will be saved for the scenes recorded in 3D, and 2D still picture will be saved for the scenes recorded in 2D. (It will be saved in 2.1 M (1920k1080).) Press the button at the location to be saved as a still picture during the playback.
HDC-Z10000P-VQT3U98_mst.book 85 ページ ２０１１年１０月４日 火曜日 午後３時２分 Playback scenes by the selected format Scenes recorded with same recording format are played back continuously. ≥ Change the mode to and touch the play mode select icon. Then, set [VIDEO/PICTURE] to [3D] or [2D]. (l 79) 1 2 Touch the format select icon. Touch [SAME FORMAT]. All the scenes are displayed by touching [ALL]. 3 Touch the playback recording format. The scenes recorded on the recording format selected are displayed as thumbnails.
HDC-Z10000P-VQT3U98_mst.book 86 ページ ２０１１年１０月４日 火曜日 午後３時２分 Playback Deleting scenes/still pictures Deleted scenes/still pictures cannot be restored, so perform appropriate confirmation of the contents before proceeding with deletion. ≥ Change the mode to and touch the play mode select icon. Then, switch to the thumbnail display of the scenes or still pictures to delete. (l 79) 1 Select the menu. MENU : [VIDEO SETUP] or [PICT.
HDC-Z10000P-VQT3U98_mst.book 87 ページ ２０１１年１０月４日 火曜日 午後３時２分 ≥ Scenes/still pictures that cannot be played back (the thumbnails are displayed as ) cannot be deleted. ≥ In case of [ALL SCENES], the deletion may take time if there are many scenes or still pictures. ≥ If you delete scenes recorded on other products or still pictures conforming to DCF standard with this unit, all the data related to the scenes/still pictures may be deleted.
HDC-Z10000P-VQT3U98_mst.book 88 ページ ２０１１年１０月４日 火曜日 午後３時２分 Playback Watching Video/Pictures on your TV Confirm the terminals on your TV and use a cable compatible with the terminals. Image quality may vary with the connected terminals. A High quality 1 HDMI terminal 2 Component terminal 3 Video terminal ≥ Use the AV multi cable (supplied) or HDMI cable (optional) and check the output settings. (l 90) ≥ HDMI is the interface for digital devices.
HDC-Z10000P-VQT3U98_mst.book 89 ページ ２０１１年１０月４日 火曜日 午後３時２分 ≥ Check that the plugs are inserted as far as they go. ≥ Please use "High Speed HDMI Cables" that have the HDMI logo (as shown on the cover). Cables not conforming to the HDMI standard will not work.Panasonic HDMI cable is recommended. Part No.: RP-CHES15 (1.5 m) ≥ Do not use any other AV multi cables except the supplied one. ≥ When connecting to the component terminal of the TV, the yellow plug of the AV multi cable is not required.
HDC-Z10000P-VQT3U98_mst.book 90 ページ ２０１１年１０月４日 火曜日 午後３時２分 Connecting with a HDMI cable Select the desired method of HDMI output. MENU : [OTHER FUNCTION] # [HDMI RESOLUTION] # [AUTO]/[1080p]/[1080i]/[480p] ≥ [AUTO] determines the output resolution automatically based on information from the connected TV. If the images are not output on the TV when the setting is [AUTO], switch to the method [1080p], [1080i] or [480p] which enables the images to be displayed on your TV.
HDC-Z10000P-VQT3U98_mst.book 91 ページ ２０１１年１０月４日 火曜日 午後３時２分 Playback Viewing with 3D compatible TV Connect the unit to a 3D compatible television compatible to the frame sequential format using a HDMI cable (optional) and play back scenes recorded in 3D to enjoy life-like and powerful 3D full high definition images.
HDC-Z10000P-VQT3U98_mst.book 92 ページ ２０１１年１０月４日 火曜日 午後３時２分 ≥ When [3D PLAYBACK] is set to [AUTO] or [3D] but the connected TV does not compatible 3D, two screens are played back.
HDC-Z10000P-VQT3U98_mst.book 93 ページ ２０１１年１０月４日 火曜日 午後３時２分 Editing With a PC What you can do with a PC HD Writer XE 1.0 You can copy the motion/still picture data to the HDD of PCs or write to media like Blu-ray discs, DVD discs or SD cards using HD Writer XE 1.0, the software installed in the supplied CD-ROM. Refer to the operating instructions of HD Writer XE 1.0 (PDF file) for details on how to use it.
HDC-Z10000P-VQT3U98_mst.book 94 ページ ２０１１年１０月４日 火曜日 午後３時２分 What can be done with the HD Writer XE 1.0 Editing: Editing motion/still picture data copied on an HDD of a PC ≥ (Scenes recorded in 3D) Delete partially, Dividing, Trimming, BGM ≥ (Scenes recorded in 2D) Dividing, Trimming, Still picture, Title, Effect, Transition, BGM, Delete partially ≥ Converting the motion picture data to MPEG2 Playing back on a PC: Play back the motion picture data in high definition picture quality on a PC.
HDC-Z10000P-VQT3U98_mst.book 95 ページ ２０１１年１０月４日 火曜日 午後３時２分 End User License Agreement Before opening the CD-ROM package, please read the following. You (“Licensee”) are granted a license for the Software defined in this End User License Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement.
HDC-Z10000P-VQT3U98_mst.book 96 ページ ２０１１年１０月４日 Article 9 With regard to MICROSOFT SQL SERVER COMPACT 3.5 produced by Microsoft Corporation (1) Licensee shall use the MICROSOFT SQL SERVER COMPACT 3.5 only when included in the Software, and shall not use the MICROSOFT SQL SERVER COMPACT 3.5 in any other configuration or method. Licensee shall not publish the MICROSOFT SQL SERVER COMPACT 3.5 or work around any technical limitations in the MICROSOFT SQL SERVER COMPACT 3.5.
HDC-Z10000P-VQT3U98_mst.book 97 ページ ２０１１年１０月４日 火曜日 午後３時２分 Operating environment ≥ Even if the system requirements mentioned in this owner’s manual are fulfilled, some PCs cannot be used. ≥ A CD-ROM drive is necessary to install the supplied software applications. (A compatible Blu-ray disc/DVD writer drive and media are necessary for writing to a Blu-ray disc/DVD.) ≥ Operation is not guaranteed in the following cases.
HDC-Z10000P-VQT3U98_mst.book 98 ページ ２０１１年１０月４日 火曜日 午後３時２分 ≥ Supplied CD-ROM is available for Windows only. ≥ Input is not supported in languages other than English, German, French, Simplified Chinese and Russian. ≥ Operation cannot be guaranteed on all Blu-ray disc/DVD drives. ≥ Operation is not guaranteed on Microsoft Windows Vista Enterprise, Windows XP Media Center Edition, Tablet PC Edition and Windows 7 Enterprise. ≥ This software is not compatible with a multi-boot environment.
HDC-Z10000P-VQT3U98_mst.book 99 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ Operating environment for the card reader function (mass storage) PC IBM PC/AT compatible PC OS Windows 7 (32 bit/64 bit) or SP1 Windows Vista (32 bit) (SP2) Windows XP (32 bit) (SP3) CPU Windows 7/Windows Vista: 1.
HDC-Z10000P-VQT3U98_mst.book 100 ページ ２０１１年１０月４日 火曜日 午後３時２分 Installation When installing the software, log on to your computer as the Administrator or with a user name with equivalent authorization. (If you do not have authorization to do this, consult your manager.) ≥ Before starting the installation, close all applications that are running. ≥ Do not perform any other operations on your PC while the software is being installed. ≥ Explanation of operations and screens is based on Windows 7.
HDC-Z10000P-VQT3U98_mst.book 101 ページ ２０１１年１０月４日 8 9 火曜日 午後３時２分 When installation is complete, some notes will appear. Check the contents, then close the window. Select [Yes, I want to restart my computer now.], then click [Finish]. The PC must be rebooted for the application to work. ∫ Uninstalling HD Writer XE 1.0 Follow the steps below to uninstall any software applications that you no longer require. 1 Select [Start] # [Control Panel] # [Uninstall a program]. 2 Select [HD Writer XE 1.
HDC-Z10000P-VQT3U98_mst.book 102 ページ ２０１１年１０月４日 火曜日 午後３時２分 Connecting to a PC ≥ Connect this unit to the PC after the software applications are installed. ≥ Remove the supplied CD-ROM from your PC. A USB cable (supplied) ≥ Insert the plugs as far as they will go. ≥ Insert the SD card. 1 Connect this unit to the AC adaptor. ≥ Use the AC adaptor to free you from worrying about the battery running down. 2 Turn on the unit. ≥ This function is available in all modes. 3 Connect this unit to a PC.
HDC-Z10000P-VQT3U98_mst.book 103 ページ ２０１１年１０月４日 火曜日 午後３時２分 About the screen indication of the unit ≥ Do not disconnect the USB cable, battery, or AC adaptor while the access lamp is on or card access icon ( ) appears on the unit screen. ≥ If the screen does not change when the unit is operated while connected to a PC, disconnect the battery and/or AC adaptor, wait approximately 1 minute, reconnect the battery and/or AC adaptor, wait approximately 1 minute again, and then turn the unit back on.
HDC-Z10000P-VQT3U98_mst.book 104 ページ ２０１１年１０月４日 火曜日 午後３時２分 Starting HD Writer XE 1.0 ≥ To use the software, log on as an Administrator or as user name for standard user account (only for Windows 7/Windows Vista). The software cannot be used with the user name for a guest account. (On the PC) Select [Start] # [All Programs] # [Panasonic] # [HD Writer XE 1.0] # [HD Writer XE]. ≥ For details on how to use the software applications, read the PDF operating instructions of the software.
HDC-Z10000P-VQT3U98_mst.book 105 ページ ２０１１年１０月４日 火曜日 午後３時２分 If using Mac ≥ HD Writer XE 1.0 is not available for Mac. ∫ Operating environment for the card reader function (mass storage) PC OS CPU RAM Interface Other requirements Mac Mac OS X 10.7.1 Intel Core 2 Duo or better 2 GB or more USB port Mouse or equivalent pointing device ≥ Even if the system requirements mentioned in this owner’s manual are fulfilled, some PCs cannot be used.
HDC-Z10000P-VQT3U98_mst.book 106 ページ ２０１１年１０月４日 火曜日 午後３時２分 Editing Dubbing Dubbing with a Blu-ray disc recorder, video device, etc. ∫ Check before dubbing Check the equipment used for dubbing.
HDC-Z10000P-VQT3U98_mst.book 107 ページ ２０１１年１０月４日 火曜日 午後３時２分 Dubbing in high-definition picture quality 3D full high definition quality video can be saved by dubbing the scenes recorded in 3D to the AVCHD 3D compatible products with high definition (AVCHD) picture quality. You can dub using a Panasonic Blu-ray disc recorder or high-definition (AVCHD) compatible DVD recorder. ≥ Depending on the recorders or the media to be copied to, you may not be able to copy in high-definition (AVCHD) picture quality.
HDC-Z10000P-VQT3U98_mst.book 108 ページ ２０１１年１０月４日 1 火曜日 午後３時２分 Connect the unit to the Blu-ray disc recorder or high-definition (AVCHD) compatible DVD recorder. ≥ The USB function selection screen will appear on the screen of the unit. 2 Touch [RECORDER] on the screen of this unit. ≥ When you select an option other than [RECORDER], reconnect the USB cable. 3 Touch the media you wish to dub. ≥ When using the battery, the LCD monitor turns off after about 5 seconds.
HDC-Z10000P-VQT3U98_mst.book 109 ページ ２０１１年１０月４日 火曜日 午後３時２分 Dubbing in standard picture quality ∫ Dubbing using equipment without an SD card slot or a USB terminal, or using a video device You can dub by connecting an AV multi cable. ≥ The scenes recorded in 3D will be dubbed as 2D video. ≥ Images are dubbed in standard quality. ≥ Use the AC adaptor to free you from worrying about the battery running down. Change the video input on the video device and TV that this unit is connected to.
HDC-Z10000P-VQT3U98_mst.book 110 ページ ２０１１年１０月４日 火曜日 午後３時２分 Menu Using the Menu Refer to page 30 for how to set up the Menu. Camera Setup ≥ Switch to manual mode. (l 46) MENU : [CAMERA SETUP] # desired setting [CUSTOMIZE SCENE] [SCENE1]/[SCENE2]/[SCENE3]/[SCENE4]/[SCENE5]/[SCENE6] Preferred camera setting information can be saved to each scene file. Switch the scene file in accordance with the recording conditions. 1 2 Touch [CUSTOMIZE SCENE]. Touch the scene file.
HDC-Z10000P-VQT3U98_mst.book 111 ページ ２０１１年１０月４日 火曜日 午後３時２分 [DETAIL LEVEL] Adjusts the level of the image outline correction. 1 2 3 Touch [DETAIL LEVEL]. Touch / to adjust settings. Touch [EXIT] to exit the menu screen. [V DETAIL LEVEL] Adjusts the degree of vertical outline correction in images. 1 2 3 Touch [V DETAIL LEVEL]. Touch / to adjust settings. Touch [EXIT] to exit the menu screen. [DETAIL CORING] Adjusts the level to eliminate the noise of the detail. 1 2 Touch [DETAIL CORING].
HDC-Z10000P-VQT3U98_mst.book 112 ページ ２０１１年１０月４日 火曜日 午後３時２分 [MASTER PED] Adjustment of black level based on the image is performed. 1 2 3 Touch [MASTER PED]. Touch / to adjust the black level. Touch [EXIT] to exit the menu screen. [AUTO IRIS LEVEL] Adjusting brightness during the Auto Iris Mode. (l 54) [DRS] Selects the DRS (Dynamic Range Stretcher) function.
HDC-Z10000P-VQT3U98_mst.book 113 ページ ２０１１年１０月４日 火曜日 午後３時２分 [GAMMA] Tone or contrast of the image is set in accordance with the recorded scenes. 1 2 Touch [GAMMA]. Touch the desired setting item. [HD NORM]: This gamma setting is suitable for high defenition picture quality recording. [LOW]: This is a gamma setting with gradual slope at the low illuminated area. It will produce tranquil image with sharper contrast. [SD NORM]: This is the standard picture quality images setting.
HDC-Z10000P-VQT3U98_mst.book 114 ページ ２０１１年１０月４日 火曜日 午後３時２分 [MATRIX] Represents the color during the recording. 1 2 3 Touch [MATRIX]. Touch the desired setting item. [NORM1]: Suitable for recording in the open air or under a halogen lamp. [NORM2]: Suitable for brighter colors than the [NORM1] mode. [FLUO]: Suitable for recording indoors under fluorescent lamp. [CINE-LIKE]: Suitable for cinema-like image. Touch [EXIT] to exit the menu screen.
HDC-Z10000P-VQT3U98_mst.book 115 ページ ２０１１年１０月４日 火曜日 午後３時２分 Recording Setup MENU : [RECORD SETUP] # desired setting [3D/2D REC MODE] [3D]/[2D] Switch the Recording Mode to 3D or 2D. (l 36) [REC FORMAT] Switch the picture quality of the motion pictures to record. The selectable recording format differ depending on the setting of [3D/2D REC MODE]. (l 36) The frame rate and the recording method will vary depending on the recording format.
HDC-Z10000P-VQT3U98_mst.book 116 ページ ２０１１年１０月４日 火曜日 午後３時２分 ≥ Recordable time using the battery (l 20) ≥ This function’s default setting is [1080/60i] (3D recording mode)/[HA] (2D recording mode). ≥ Please refer to page 147 about approximate recordable time. ≥ When the unit is moved a lot or moved quickly, or when a fast-moving subject is recorded (particularly when recording in [HE] mode), mosaic-type noise may appear at playback. [RELAY/BACKUP] You can set the relay recording and backup recording.
HDC-Z10000P-VQT3U98_mst.book 117 ページ ２０１１年１０月４日 火曜日 午後３時２分 [TIME LAPSE REC] A scene that moves slowly for long period of time is recorded frame by frame with an interval, and is recorded as a short time motion picture. One frame is recorded every recording interval that is set. The scene of one second is made up by 30 frames. ≥ Switch to manual mode. (l 46) ≥ Set [3D/2D REC MODE] to [2D]. (l 36) [OFF]: Cancel the setting.
HDC-Z10000P-VQT3U98_mst.book 118 ページ ２０１１年１０月４日 火曜日 午後３時２分 [TCG] [FREE RUN]/[REC RUN] Sets the way the time code will move. (l 64) [TC PRESET] Initial value of the time code can be set. (l 65) [UB PRESET] User Information can be set. (l 65) [PRE-REC] It will switch to the recording screen and record the image and audio from approximately 3 seconds prior to pressing the recording start/stop button when [PREREC] is touched. ≥ PRE-REC appears on the screen. ≥ Aim the unit at the subject beforehand.
HDC-Z10000P-VQT3U98_mst.book 119 ページ ２０１１年１０月４日 火曜日 午後３時２分 [HYBRID O.I.S.] [ON]/[OFF] You can set the Hybrid Optical Image Stabilizer. (l 50) ≥ This can only be selected when the [3D/2D REC MODE] is [2D]. [AUTO SLOW SHTR] [ON]/[OFF] You can record bright pictures even in dark places by slowing the shutter speed. ≥ The shutter speed is 1/30 or more depending on the ambient brightness.
HDC-Z10000P-VQT3U98_mst.book 120 ページ ２０１１年１０月４日 火曜日 午後３時２分 [WIND NOISE CANCELER] [ON]/[OFF] This will reduce the wind noise coming into the built-in microphones while maintaining the realism. ≥ Set the [MIC SETUP] to anything other than [2ch]. (l 57) ≥ You may not see the full effect depending on the recording conditions. [AUDIO REC] [ ]/[LPCM] Switches the sound quality for the audio recording.
HDC-Z10000P-VQT3U98_mst.book 121 ページ ２０１１年１０月４日 火曜日 午後３時２分 [BASS SETTING] Change the lower setting of the built-in microphone (5.1 ch) according to your choice. ≥ Set the [MIC SETUP] to [SURROUND] or [ZOOM MIC]. (l 57) [0dB]/[+3dB]/[+6dB]/[LOWCUT] ≥ Normally set to [0dB]. ≥ Select [+3dB] or [+6dB] to get strong power feeling at bass level. [2ch MIC ALC] [ON]/[OFF] ≥ Set [MIC SETUP] to [2ch].
HDC-Z10000P-VQT3U98_mst.book 122 ページ ２０１１年１０月４日 火曜日 午後３時２分 Switch and display setting Menu items displayed are different depending on the position or setting of the mode switch. MENU : [SW & DISP SETUP] # desired setting [MEDIA SELECT] [SD CARD 1] and [SD CARD 2] can be selected separately to record motion pictures or still pictures. (l 35) [IRIS RING] Sets the rotation direction and iris control of the iris ring. ≥ Switch to manual mode.
HDC-Z10000P-VQT3U98_mst.book 123 ページ ２０１１年１０月４日 火曜日 午後３時２分 [ZEBRA DETECT 2] [SET]/[OFF] Selects the brightness level of the right-leaning zebra patterns on the screen. 1 Touch [ZEBRA DETECT 2]. ≥ Touch [SET]. 2 3 Touch / to adjust settings. Touch [ENTER]. ≥ Touch [EXIT] to exit the menu screen. ≥ Zebra 2 can be displayed by pressing the ZEBRA button after setting. (l 76) [MARKER] [ON]/[OFF] Displaying of the luminance level display marker can be switched.
HDC-Z10000P-VQT3U98_mst.book 124 ページ ２０１１年１０月４日 火曜日 午後３時２分 [REC COUNTER] [TOTAL]/[SCENE] Selects the operation of the Recording Counter during recording. (l 66) [VIDEO OUT OSD] [ON]/[OFF] The information displayed on the screen (operation icon and counter display etc.) can be displayed/not displayed on the TV. (l 89) [DATE/TIME] [OFF]/[TIME]/[DATE]/[DATE&TIME] It is possible to change the date and time display mode.
HDC-Z10000P-VQT3U98_mst.book 125 ページ ２０１１年１０月４日 火曜日 午後３時２分 [LENS STATUS] [ON]/[OFF] Display relating to lens can be switched. (Zoom Display, Optical Image Stabilizer, Focus Display, White Balance, Iris, Gain, Auto Iris, Shutter Speed, 3D Macro) [CARD&BATTERY] [ON]/[OFF] Display can be switched between the remaining recordable time of the SD card and the remaining battery capacity indication.
HDC-Z10000P-VQT3U98_mst.book 126 ページ ２０１１年１０月４日 火曜日 午後３時２分 [POWER LCD] [ON]/[OFF] This makes it easier to view the LCD monitor in bright places including outdoors. (l 27) [LCD SET] It adjusts brightness and color density on the LCD monitor. (l 27) [EVF SET] [BRIGHT]/[NORMAL]/[DARK] Brightness of the viewfinder can be switched. (l 28) [SELF SHOOT] [MIRROR]/[NORMAL] Switches the mirror function of the LCD monitor when recording yourself.
HDC-Z10000P-VQT3U98_mst.book 127 ページ ２０１１年１０月４日 火曜日 午後３時２分 Other Functions Menu items displayed are different depending on the position or setting of the mode switch. MENU : [OTHER FUNCTION] # desired setting [FORMAT CARD] The SD card can be formatted. (l 34) ≥ Please be aware that if a medium is formatted, then all the data recorded on the medium will be erased and cannot be restored. Back up important data on a PC, disc etc.
HDC-Z10000P-VQT3U98_mst.book 128 ページ ２０１１年１０月４日 火曜日 午後３時２分 [CLOCK SET] Set date and time. (l 29) [TIME ZONE] Set the time difference from Greenwich Mean Time. (l 29) [ALERT SOUND] [OFF]/ (Volume low)/ (Volume high) Touch screen operation, start and stop of recording can be confirmed with this sound. 2 Beeps for 4 times When an error occurs. Check the sentence displayed on the screen.
HDC-Z10000P-VQT3U98_mst.book 129 ページ ２０１１年１０月４日 火曜日 午後３時２分 [QUICK POWER ON] [ON]/[OFF] The unit is put into recording pause approx. 2 second when the unit is turned on with the mode set to . ≥ Depending on the recording conditions, start time may be longer than 2 second. ≥ In the quick power on mode, the zoom magnification becomes 1k. [HDMI RESOLUTION] [AUTO]/[1080p]/[1080i]/[480p] Select the desired method of HDMI output.
HDC-Z10000P-VQT3U98_mst.book 130 ページ ２０１１年１０月４日 火曜日 午後３時２分 [INITIAL SET] The menu settings or [CUSTOMIZE SCENE] back to the default setting. (l 110) [ALL]: This is for initializing all menus. [SCENE]: This is for initializing the setting of customise scene. ≥ Settings for [3D/2D REC MODE], [REC FORMAT], [MEDIA SELECT], [CLOCK SET] and [LANGUAGE] will not be changed. [CALIBRATION] Perform the touch screen calibration if a different object to the one touched is selected.
HDC-Z10000P-VQT3U98_mst.book 131 ページ ２０１１年１０月４日 火曜日 午後３時２分 Video Setup ≥ Change the mode to and touch the play mode select icon. Then, set [VIDEO/PICTURE] to [3D] or [2D]. (l 79) MENU : [VIDEO SETUP] # desired setting [REPEAT PLAY] [ON]/[OFF] Playback of the first scene starts after playback of the last scene finishes when set to [ON]. (l 84) [RESUME PLAY] [ON]/[OFF] If playback of a scene was stopped halfway, the playback can be resumed from where it was stopped when set to [ON].
HDC-Z10000P-VQT3U98_mst.book 132 ページ ２０１１年１０月４日 火曜日 午後３時２分 Display Indications ∫ Recording indications TC 00:00:00:00 R 1h20m R 1h20m 60 i 1/100 PRE-REC 3D 0dB D 5X NOV 15 2011 3:30:00PM MF50 C10 3D 2.
HDC-Z10000P-VQT3U98_mst.book 133 ページ ２０１１年１０月４日 5.1 ch Microphone Level (ALC) (l 61)/ 2 ch Microphone ALC (l 121) Wind Noise Canceler (l 120) 10 Counter Display (l 63) No.0010 Scene Number (In Playback Mode) NOV 15 2011 Date indication 3:30PM Time indication (l 29) Repeat Playback (l 84) Convergence point (l 39) Resume Playback (l 84) 3D 2.
HDC-Z10000P-VQT3U98_mst.book 134 ページ ２０１１年１０月４日 火曜日 午後３時２分 Display Messages Major confirmation/error messages to be indicated on the screen in text. CHECK CARD. This card is not compatible or it cannot be recognized by the unit. If this message appears even though motion pictures and still pictures are recorded on an SD card, the card may be unstable. Reinsert the SD card, then turn the unit off and then on again. INVALID/CANNOT SET.
HDC-Z10000P-VQT3U98_mst.book 135 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Troubleshooting ∫ It is not a malfunction in following cases A clicking sound is heard when the unit is shaken. ≥ This is the sound of the lens moving and is not a defect. This sound will no longer be heard when the unit is turned on and change the mode to . Object seems to be warped. ≥ Object seems to be warped slightly when the object moves across the image very fast, but this is because the unit is using MOS for the image sensor.
HDC-Z10000P-VQT3U98_mst.book 136 ページ ２０１１年１０月４日 火曜日 午後３時２分 Indication Problem Function display (Remaining Display, Counter Display, etc.) is not displayed Check points ≥ [CARD&BATTERY] or [OTHER DISPLAY] of the [SW & DISP SETUP] is [OFF]. (l 125) Recording Problem Check points The unit arbitrarily stops recording. ≥ Use an SD card that can be used for motion picture recording.
HDC-Z10000P-VQT3U98_mst.book 137 ページ ２０１１年１０月４日 火曜日 午後３時２分 Playback Problem Check points Scenes/still pictures cannot be played back. ≥ Any scenes/still pictures where the thumbnails are displayed as cannot be played back. Scenes/still pictures cannot be deleted. ≥ Release the protect setting. (l 87) ≥ Any scenes/still pictures where the thumbnails are displayed as cannot be deleted. If the scenes/still pictures are unnecessary, format the media to erase the data.
HDC-Z10000P-VQT3U98_mst.book 138 ページ ２０１１年１０月４日 火曜日 午後３時２分 With a PC Problem Check points When connected by the USB cable, this unit is not detected by the PC. ≥ After re-inserting the SD card into the unit, reconnect the supplied USB cable. ≥ Select another USB terminal on the PC. ≥ Check the operating environment. (l 97, 105) ≥ Connect the supplied USB cable again after restarting the PC and turning on this unit again. When the USB cable is disconnected, an error message will appear on the PC.
HDC-Z10000P-VQT3U98_mst.book 139 ページ ２０１１年１０月４日 火曜日 午後３時２分 ∫ If scenes do not change smoothly when played back on another device The images may be still for several seconds at the joins between the scenes if the following operations are performed when multiple scenes have been continuously played back using another unit. ≥ Just how smoothly the scenes will be played back depends on the playback unit.
HDC-Z10000P-VQT3U98_mst.book 140 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Cautions for use About this unit The unit and the SD card become warm during use. This is not a malfunction. Keep this unit as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). ≥ If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be disrupted by electromagnetic wave radiation.
HDC-Z10000P-VQT3U98_mst.book 141 ページ ２０１１年１０月４日 ≥ When using a chemical dust cloth, follow the instructions that came with the cloth. Do not use the unit for surveillance purposes or other business uses. ≥ This unit was designed for consumer intermittent use. It was not intended for continuous use, or for any industrial or commercial application resulting in prolonged use. ≥ In certain situations, continuous use could cause the unit to overheat and cause a malfunction. Such use is strongly discouraged.
HDC-Z10000P-VQT3U98_mst.book 142 ページ ２０１１年１０月４日 deformed state, this unit or battery charger may be damaged. Do not throw old battery into fire. ≥ Heating a battery or throwing it into a fire may result in an explosion. If the operating time is very short even after the battery has been recharged, the battery has worn out. Please purchase a new battery.
HDC-Z10000P-VQT3U98_mst.book 143 ページ ２０１１年１０月４日 About 3D About 3D recording After adjusting the convergence dial, check that you can view images in 3D ≥ It may not be possible to correctly record 3D image in following cases: j When operating the zoom after adjustment or changing the subject j When recording with the convergence point in an extreme forward or rearward position ≥ Use the 3D guide display as guidance. (l 41) Do not record a subject at less than the minimum focus distance.
HDC-Z10000P-VQT3U98_mst.book 144 ページ ２０１１年１０月４日 About the SD card When disposing of or giving away the SD card, note that: ≥ Formatting and deletion of this unit or computer only changes the file management information and does not completely delete the data in the SD card. ≥ It is recommended that the main SD card is either physically destroyed or the SD card is physically formatted using this unit when disposing of or giving away the SD card.
HDC-Z10000P-VQT3U98_mst.book 145 ページ ２０１１年１０月４日 火曜日 午後３時２分 About condensation When condensation forms on the unit, the lens will cloud up and the unit may not work properly. Make every effort to ensure that condensation does not form. If it does form, take the actions described below. Causes of condensation Condensation takes place when the ambient temperature or humidity is changed as follows. ≥ When this unit is brought inside from the cold (e.g. a ski slope) to a warm room.
HDC-Z10000P-VQT3U98_mst.book 146 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others About copyright ∫ Carefully observe copyright laws Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights. ∫ Licenses ≥ SDXC Logo is a trademark of SD-3C, LLC.
HDC-Z10000P-VQT3U98_mst.book 147 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Recording modes/approximate recordable time ≥ SD cards are only mentioned with their main memory size. The stated times are the approximate recordable times for continuous recording.
HDC-Z10000P-VQT3U98_mst.book 148 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Approximate number of recordable pictures ≥ SD cards are only mentioned with their main memory size. The stated number is the approximate number of recordable pictures. When [3D/2D REC MODE] is set to [3D] Picture size Recording format of the still picture 4 GB SD card 16 GB 64 GB 2.
HDC-Z10000P-VQT3U98_mst.book 149 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Specifications High Definition Video Camera Information for your safety Power source: DC 12 V (When using AC adaptor) DC 7.2 V (When using battery) Power consumption: 16.7 W Recording format: AVCHD format version 2 compliant (AVCHD 3D/AVCHD Progressive) Motion picture compression: 3D Recording Mode; MPEG-4 MVC/H.264 2D Recording Mode; MPEG-4 AVC/H.264 Audio compression: Dolby Digital (5.
HDC-Z10000P-VQT3U98_mst.book 150 ページ ２０１１年１０月４日 火曜日 午後３時２分 Image sensor: 1/4.1z 3MOS image sensor k2 Total; 9150 K (3050 Kk3) k2 Effective pixels; 3D Recording Mode Motion picture/Still picture; 6210 K (2070 Kk3) (16:9) k2 2D Recording Mode Motion picture/Still picture; 6570 K (2190 Kk3) (16:9) Lens: Auto Iris optical zoom (Full range AF) F value (focal length) 3D Recording Mode; F1.5 to F2.7 (Focal length; 2.84 mm to 28.4 mm) 2D Recording Mode; F1.5 to F2.8 (Focal length; 2.84 mm to 34.
HDC-Z10000P-VQT3U98_mst.book 151 ページ ２０１１年１０月４日 火曜日 午後３時２分 AV multi connector video output level: Component video output level; Y; 1.0 Vp-p, 75 h Pb; 0.7 Vp-p, 75 h Pr; 0.7 Vp-p, 75 h AV video output level; 1.0 Vp-p, 75 h HDMI connector video output level: HDMI™ (x.v.Colour™) 1080p/1080i/480p AV multi connector audio output level (Line): 2 ch HDMI connector audio output level: Dolby Digital/Linear PCM Headphone output: 3.5 mm (0.
HDC-Z10000P-VQT3U98_mst.book 152 ページ ２０１１年１０月４日 火曜日 AC adaptor Information for your safety Power source: Power consumption: DC output: AC 110 V to 240 V, 50/60 Hz 42 W DC 12 V, 2.5 A Dimensions: 115 mm (W)k37 mm (H)k57 mm (D) [4.53 q (W)k1.46 q (H)k2.24 q (D)] Mass: Approx. 210 g (Approx. 0.46 lbs.) Battery charger Information for your safety Power source: Power consumption: DC output: AC 100 V to 240 V, 50/60 Hz 0.4 A DC 8.4 V, 1.2 A Dimensions: 70 mm (W)k44.5 mm (H)k116 mm (D) [2.76 q (W)k1.
HDC-Z10000P-VQT3U98_mst.book 153 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Optional accessories Accessory No.
HDC-Z10000P-VQT3U98_mst.book 154 ページ ２０１１年１０月４日 火曜日 午後３時２分 Accessory Order Form (For USA and Puerto Rico Customers) Please photocopy this form when placing an order. 1. Model # 2. Items Ordered Accessory # Description Price Each Quantity Total Price Subtotal Your State & Local Sales Tax Shipping & Handling 6.95 Total Enclosed 3. Method of payment (check one) Check of Money Order enclosed (NO C.O.D.
HDC-Z10000P-VQT3U98_mst.book 155 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Limited Warranty (ONLY FOR U.S.A.
HDC-Z10000P-VQT3U98_mst.book 156 ページ ２０１１年１０月４日 火曜日 午後３時２分 THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content.
HDC-Z10000P-VQT3U98_mst.book 157 ページ ２０１１年１０月４日 火曜日 午後３時２分 Others Useful Information (Only For Latin American Countries) Customer Service Customer Service Directory Obtain product information and operative assistant; localize the closer distributor or Service Center; buy spare parts and accessories by our web site to Latin American: http://www.lar.panasonic.
HDC-Z10000P-VQT3U98_mst.book 158 ページ ２０１１年１０月４日 火曜日 午後３時２分 Index ∫ Numerics 2ch MIC ALC . . . . . . . . . . . . . . . . . . . . 121 2ch stereo microphone . . . . . . . . . . . . . 57 3D Display . . . . . . . . . . . . . . . . . . . . . . . 72 3D FINE . . . . . . . . . . . . . . . . . . . . . . . . 43 3D guide . . . . . . . . . . . . . . . . . . . . . . . 123 3D guide display . . . . . . . . . . . . . . . . . . 41 3D macro . . . . . . . . . . . . . . . . . . . . . . . . 73 3D output . . . . . . . . . . .
HDC-Z10000P-VQT3U98_mst.book 159 ページ ２０１１年１０月４日 ∫K Knee point . . . . . . . . . . . . . . . . . . . . . 113 ∫L Language . . . . . . . . . . . . . . . . . . . . . . 130 Last scene delete . . . . . . . . . . . . . . . . 74 LCD monitor . . . . . . . . . . . . . 14, 25, 144 LCD set . . . . . . . . . . . . . . . . . . . . 27, 126 Lens cap . . . . . . . . . . . . . . . . . . . . . . . 16 Lens status . . . . . . . . . . . . . . . . . . . . 125 Level meter . . . . . . . . . . . . . . . . . . . .
HDC-Z10000P-VQT3U98_mst.
