Camcorder User Manual

ManualsBrandsPanasonic ManualsCamcorderHDC-SD800P

until

2010/12/27

For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or,

Owner’s Manual

High Definition Video Camera

Model No. HDC-SD800P

Before connecting, operating or adjusting this product, please read the instructions completely.

VQT3K35

HDCSD800P-VQT3K35_mst.book 1 ページ２０１０年１２月２０日　月曜日　午前９時４分

Summary of content (168 pages)

PAGE 1
HDCSD800P-VQT3K35_mst.book 1 ページ２０１０年１２月２０日月曜日午前９時４分 Owner’s Manual High Definition Video Camera Model No. HDC-SD800P Before connecting, operating or adjusting this product, please read the instructions completely. For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.
PAGE 2
HDCSD800P-VQT3K35_mst.book 2 ページ２０１０年１２月２０日 Things You Should Know Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. The serial number is on the tag located on the back of your camera. Be sure to retain this manual as your convenient camera information source.
PAGE 3
HDCSD800P-VQT3K35_mst.book 3 ページ２０１０年１２月２０日月曜日午前９時４分 FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
HDCSD800P-VQT3K35_mst.book 4 ページ２０１０年１２月２０日月曜日午前９時４分 AC adaptor This AC adaptor operates on AC between 110 V and 240 V. But ≥ In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power supply only. ≥ When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to suit the AC outlet configuration. ≥ When connecting to a supply of greater than AC 125 V, ensure the cord you use is suited to the voltage of the AC supply and the rated current of the AC adaptor.
PAGE 5
HDCSD800P-VQT3K35_mst.book 5 ページ２０１０年１２月２０日月曜日午前９時４分 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. ∫ Product Identification Marking Product Location High Definition Video Camera Battery holder AC adaptor Bottom U.S.A. CONSUMERS: ATTENTION: A lithium ion/polymer battery that is recyclable powers the product you have purchased.
PAGE 6
HDCSD800P-VQT3K35_mst.book 6 ページ２０１０年１２月２０日月曜日午前９時４分 IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
PAGE 7
HDCSD800P-VQT3K35_mst.book 7 ページ２０１０年１２月２０日月曜日午前９時４分 Precautions USE & LOCATION WARNING ≥ TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee.
PAGE 8
HDCSD800P-VQT3K35_mst.book 8 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ About the recording format for recording motion pictures ∫ Cards that you can use with this unit You can select from AVCHD, 1080/60p or iFrame recording formats to record motion pictures using this unit. (l 51, 61) AVCHD: You can record high definition quality images with this format. It is suitable for viewing on a large format TV or for saving to disc.
PAGE 9
午前９時４分 Parts identification and handling .......... 16 Power supply........................................... 19 Inserting/removing the battery........... 19 Charging the battery ......................... 20 Charging and recording time............. 21 Preparation of SD cards .........................22 Cards that you can use with this unit ...................................... 22 Inserting/removing an SD card.......... 23 Turning the unit on/off............................
PAGE 10
HDCSD800P-VQT3K35_mst.book 10 ページ２０１０年１２月２０日 Deleting scenes/still pictures ................ 91 Dividing a scene (AVCHD, 1080/60p) .......................... 92 Dividing a scene to partially delete (iFrame) ............................................ 93 Deleting personal information ........... 94 Protecting scenes/still pictures.......... 95 DPOF setting ........................................... 96 Watching Video/Pictures on your TV ...............................................
PAGE 11
HDCSD800P-VQT3K35_mst.book 11 ページ２０１０年１２月２０日月曜日午前９時４分 Accessories Check the accessories before using this unit. Keep the accessories out of reach of children to prevent swallowing. Product numbers correct as of Dec. 2010. These may be subject to change.
PAGE 12
HDCSD800P-VQT3K35_mst.book 12 ページ２０１０年１２月２０日月曜日午前９時４分 Quick Guide ∫ Inserting the battery Install the battery by inserting it in the direction shown in the figure. ∫ Inserting/removing an SD card   A Insert the battery until it clicks and locks.  ∫ Charging the battery Access lamp [ACCESS] A ≥ When this unit is accessing the SD card, the access lamp lights up.  A DC input terminal 1 Connect the AC adaptor to the DC input terminal.
PAGE 13
HDCSD800P-VQT3K35_mst.book 13 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ Turning the unit on/off ∫ Selecting a mode Turning the unit on and off with the power button Press the power button to turn on the unit. Operate the mode switch to change the mode to , or . Motion Picture Recording Mode (l 30) A The status indicator lights on. ≥ To turn off the unit, hold down the power button until the status indicator goes off. Turning the unit on and off with the LCD monitor Opening the LCD monitor turns on the unit.
PAGE 14
HDCSD800P-VQT3K35_mst.book 14 ページ２０１０年１２月２０日 Touch Menu Touch to display the Touch Menu. Touch (left side)/ (right side) of on the Touch Menu to switch the operation icons. 月曜日午前９時４分 ∫ Recording motion pictures 1) 2) 3) Change the mode to . Open the LCD monitor. Press the recording start/stop button to start recording. T W A When you begin recording, ; changes to ¥. A Touch Menu ∫ Recording still pictures ∫ Language selection 1) 2) 3) 1) 2) Touch [MENU], then touch [SETUP] # [LANGUAGE].
PAGE 15
HDCSD800P-VQT3K35_mst.book 15 ページ２０１０年１２月２０日 ∫ Motion picture/Still picture playback 1) 2) Change the mode to . Touch the play mode select icon A. ALL 3) Touch the [VIDEO/PICTURE] you wish to play back. ≥ Touch [ENTER]. 4) Touch the scene or the still picture to be played back. 月曜日午前９時４分 for a specific period of time. To display them again, touch the screen. (Motion picture playback) 1/;: Playback/Pause 6: Rewind playback 5: Fast forward playback ∫: Stops the playback and shows the thumbnails.
PAGE 16
HDCSD800P-VQT3K35_mst.book 16 ページ２０１０年１２月２０日月曜日午前９時４分 Preparation Parts identification and handling 1 2 3 4 1 2 34 5 6 7 8 9 10 11 13 12 14 15 16 17 18 19 20 16 VQT3K35 Speaker Power button [ ] (l 24) Inlet (cooling fan) (l 28) Intelligent auto/Manual button [iA/MANUAL] (l 34, 75) 5 Optical image stabilizer button [ O.I.S.
PAGE 17
HDCSD800P-VQT3K35_mst.book 17 ページ２０１０年１２月２０日月曜日午前９時４分 21 LCD monitor (Touch screen) (l 25) 21 ≥ It can open up to 90o. ≥ It can rotate up to 180o A towards the lens or 90o B towards the opposite direction. Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture. 22 Tripod receptacle ≥ If you attach a tripod which has 5.5 mm (0.
PAGE 18
HDCSD800P-VQT3K35_mst.book 18 ページ 23 24 25 27 28 月曜日午前９時４分 23 Status indicator (l 24) 24 Photoshot button [ ] (l 32) 25 Zoom lever [W/T] (In Motion Picture Recording Mode or Still Picture Recording Mode) (l 49) Thumbnail display switch [ / ]/ Volume lever [sVOLr] (In Playback Mode) (l 37) 26 Internal microphones 27 Mode switch (l 25) 28 Recording start/stop button (l 30) 29 Shoulder strap fixture 30 Grip belt Adjust the length of the grip belt so that it fits your hand.
PAGE 19
HDCSD800P-VQT3K35_mst.book 19 ページ２０１０年１２月２０日月曜日午前９時４分 Preparation Power supply ∫ About batteries that you can use with this unit The battery that can be used with this unit is VW-VBN130/VW-VBN260. ≥ The unit has a function for distinguishing batteries which can be used safely. The dedicated battery (VW-VBN130/VW-VBN260) supports this function. The only batteries suitable for use with this unit are genuine Panasonic products and batteries manufactured by other companies and certified by Panasonic.
PAGE 20
HDCSD800P-VQT3K35_mst.book 20 ページ２０１０年１２月２０日月曜日午前９時４分 Charging the battery When this unit is purchased, the battery is not charged. Charge the battery fully before using this unit for the first time. Important: ≥ Use the supplied AC adaptor. Do not use the AC adaptor of another device. ≥ Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do not use the AC cable from other equipment with this unit.
PAGE 21
HDCSD800P-VQT3K35_mst.book 21 ページ２０１０年１２月２０日月曜日午前９時４分 Charging and recording time ∫ Charging/Recording time ≥ Temperature: 25 oC (77 oF)/humidity: 60%RH Battery model number [Voltage/Capacity (minimum)] Charging time Recording mode Maximum continuous recordable time [1080/60p] 1 h 35 min [HA] 1 h 40 min [HG], [HX], [HE] 1 h 45 min [iFrame] 1 h 50 min [1080/60p] 3 h 5 min Actual recordable time 1h Supplied battery/ VW-VBN130 (optional) [7.
PAGE 22
HDCSD800P-VQT3K35_mst.book 22 ページ２０１０年１２月２０日月曜日午前９時４分 Preparation Preparation of SD cards This unit (an SDXC compatible device) is compatible with SD Memory Cards, SDHC Memory Cards and SDXC Memory Cards. When using an SDHC memory card/SDXC memory card with other equipment, check the equipment is compatible with these memory cards. Cards that you can use with this unit Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for motion picture recording.
PAGE 23
HDCSD800P-VQT3K35_mst.book 23 ページ２０１０年１２月２０日月曜日午前９時４分 Inserting/removing an SD card When using an SD card not from Panasonic, or one previously used on other equipment, for the first time on this unit, format the SD card. (l 45) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored. Caution: Check that the access lamp has gone off. Access lamp [ACCESS] A ≥ When this unit is accessing the SD card, the access lamp lights up.
PAGE 24
HDCSD800P-VQT3K35_mst.book 24 ページ２０１０年１２月２０日月曜日午前９時４分 Preparation Turning the unit on/off You can turn the unit on and off using the power button or by opening and closing the LCD monitor. A clicking sound is heard when the unit is shaken. ≥ This is the sound of the lens moving and is not a defect. This sound will no longer be heard when the unit is turned on and change the mode to or . Turning the unit on and off with the power button Press the power button to turn on the unit.
PAGE 25
HDCSD800P-VQT3K35_mst.book 25 ページ２０１０年１２月２０日月曜日午前９時４分 Preparation Selecting a mode Change the mode to recording or playback. Operate the mode switch to change the mode to , or . Motion Picture Recording Mode (l 30) Still Picture Recording Mode (l 32) Playback Mode (l 36, 82) Preparation How to use the touch screen You can operate by directly touching the LCD monitor (touch screen) with your finger.
PAGE 26
HDCSD800P-VQT3K35_mst.book 26 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ About the operation icons / / / : These icons are used to switch the menu and thumbnail display page, for item selection and setting etc. : Touch to return to the previous screen such as when setting menus. About the Touch Menu Touch Touch (left side)/ (right side) of (left side)/ on the Touch Menu to switch the operation icons. (right side) of on the Touch Menu.
PAGE 27
HDCSD800P-VQT3K35_mst.book 27 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ To display the Touch Menu The Touch Menu will disappear when no function is performed for a specific period of time during Recording mode. To display it again, touch . ≥ Do not touch on the LCD monitor with hard pointed tips, such as ball point pens. ≥ Perform the touch screen calibration when the touch is not recognized or wrong location is recognized.
PAGE 28
HDCSD800P-VQT3K35_mst.book 28 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Before recording ∫ Basic camera positioning 1 Hold the unit with both hands. 2 Put your hand through the grip belt. 3 It is convenient to use the recording button icon A when holding the unit at waist level. ≥ When recording, make sure your footing is stable and there is no danger of colliding with another person or object. ≥ When you are outdoors, record pictures with the sunlight behind you.
PAGE 29
HDCSD800P-VQT3K35_mst.book 29 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ To recording yourself Rotate the LCD monitor towards the lens side. ≥ The image is horizontally flipped as if you see a mirror image. (However the image recorded is the same as a normal recording.) ≥ Only some indications will appear on the screen. When appears, return the direction of the LCD monitor to normal position and check the warning/alarm indication.
PAGE 30
HDCSD800P-VQT3K35_mst.book 30 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Recording motion pictures 1 2 3 Change the mode to Open the LCD monitor. Press the recording start/stop button to start recording. A When you begin recording, ; changes to ¥. 4  . T W  Press the recording start/stop button again to pause recording. B You can also start or pause recording by touching the recording start/stop button icon. This icon functions in the same manner as the recording start/stop button.
PAGE 31
HDCSD800P-VQT3K35_mst.book 31 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ There are 3 recording formats that can be used with this unit: AVCHD that records high-definition motion pictures, 1080/60p that records motion pictures in maximum quality for this unit and iFrame that records motion pictures suitable for playback and editing on Mac (iMovie’11). To change the recording format, change the Recording Mode (l 61) or press and hold the 1080/60p button.
PAGE 32
HDCSD800P-VQT3K35_mst.book 32 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Recording still pictures 1 2 3 Change the mode to 4 Press the . Open the LCD monitor. Press the button halfway. (For Auto focus only) button fully. Focus indication:   A Focus indication ± (The white lamp flashes.): Focusing ¥ (The green lamp lights up.): When in focus No mark: When focusing is unsuccessful.
PAGE 33
HDCSD800P-VQT3K35_mst.book 33 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ About the screen indications in Still Picture Recording : R3000: : 14.2M : MEGA : : : ß: ßj: : Still picture operation indicator (l 131) Remaining number of still pictures (Flashes in red when [0] appears.) Quality of still pictures (l 72) Size of still pictures (l 71) MEGA optical image stabilizer (l 32) Optical image stabilizer (l 50) AF assist lamp (l 74) Flash (l 57) Flash level (l 57) Red-eye reduction (l 58) R3000 14.
PAGE 34
HDCSD800P-VQT3K35_mst.book 34 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Intelligent Auto Mode The following modes (appropriate for the condition) are set just by pointing the unit to what you want to record. /MANUAL Intelligent auto/Manual button Press this button to switch Intelligent Auto Mode/Manual Mode. ≥ Please refer to page 75 for details about Manual Mode.
PAGE 35
HDCSD800P-VQT3K35_mst.book 35 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ Faces cannot be detected depending on the recording conditions, such as when faces are of certain sizes or at certain tilts or when digital zoom is used. ≥ [ZOOM MIC] is set to [OFF] in the Intelligent Auto Mode. (l 68) ∫ Intelligent Auto Mode When switching to Intelligent Auto Mode, the Auto White Balance and Auto Focus operate and automatically adjust the color balance and focusing. Depending on the brightness of the subject etc.
PAGE 36
HDCSD800P-VQT3K35_mst.book 36 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Motion picture/Still picture playback 1 2 Change the mode to 3 Select the [VIDEO/PICTURE] you wish to play back. . Touch the play mode select icon A. (l 26) ALL ≥ Touch [ENTER]. 4 Touch the scene or the still picture to be played back.  B is displayed when [1080/60p] is touched, is ALL displayed when [AVCHD] is touched or is displayed when [iFrame] is touched in step 3.
PAGE 37
HDCSD800P-VQT3K35_mst.book 37 ページ２０１０年１２月２０日 Motion picture playback 1/;: 6: 5: ∫: Playback/Pause Rewind playback Fast forward playback Stops the playback and shows the thumbnails. 月曜日午前９時４分 Still picture playback 1/;: 2;: ;1: ∫: Slide show (playback of the still pictures in numerical order) start/pause. Plays back the previous picture. Plays back the next picture. Stops the playback and shows the thumbnails.
PAGE 38
HDCSD800P-VQT3K35_mst.book 38 ページ Motion picture compatibility ２０１０年１２月２０日月曜日午前９時４分 Please refer to page 51 about 1080/60p. ≥ This unit is based on AVCHD format/MPEG-4 AVC file format. ≥ Video signals for the AVCHD that can be played back with this unit are 1920k1080/60i, 1920k1080/24p and 1440k1080/60i. ≥ Video signals for the iFrame that can be played back with this unit are 960k540/30p.
PAGE 39
HDCSD800P-VQT3K35_mst.book 39 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Using the menu screen ≥ Touch 1 (left side)/ (right side) of Touch [MENU]. on the Touch Menu to display MENU . (l 26) 4 Touch the desired item to enter the setting. 5 Touch [EXIT] to exit the menu setting. Q. MENU MENU 2 Touch the top menu A. ∫ About 3 Touch the submenu B. guide display After touching , touching the submenus and items will cause function descriptions and settings confirmation messages to appear.
PAGE 40
HDCSD800P-VQT3K35_mst.book 40 ページ２０１０年１２月２０日月曜日午前９時４分 Using the quick menu This allows quick setting of some of the menus. ≥ Touch (left side)/ (right side) of on the Touch Menu to display 1 Q. MENU . (l 26) Touch [Q.MENU]. The following menus can be set. Touch the desired menu. ≥ The items displayed differ depending on the position of the mode switch or settings. Icon 14.2M / 13.
PAGE 41
HDCSD800P-VQT3K35_mst.book 41 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Using the Setup Menu ≥ The items displayed differ depending on the position or settings of the mode switch. Select the menu. MENU : [SETUP] # desired setting [CLOCK SET] Please refer to page 27. [SET WORLD TIME] It is possible to display and record the time at the travel destination by selecting your home region and the travel destination. 1 Touch [SET WORLD TIME]. ≥ If the clock is not set, adjust the clock to the current time.
PAGE 42
HDCSD800P-VQT3K35_mst.book 42 ページ 5 ２０１０年１２月２０日月曜日午前９時４分 (Only when setting the region of your travel destination)  Touch / to select your travel destination and touch [ENTER]. ≥ Touch [SUMMER TIME SET] to set daylight saving time. appears and the summer time setting is turned on. The travel destination time and time difference from the home region time are set forward by one hour. Touch [SUMMER TIME SET] again to return to the normal time setting. ≥ Close the setting by touching [EXIT].
PAGE 43
HDCSD800P-VQT3K35_mst.book 43 ページ [QUICK POWER ON] ２０１０年１２月２０日月曜日午前９時４分 [OFF]/[ON] The unit is put into recording pause approx. 1 second when the unit is turned on with the mode set to or . ≥ Depending on the recording conditions, start time may be longer than 1 second. ≥ In the Quick power on mode, the zoom magnification becomes 1k. [QUICK START] [OFF]/[ON] This unit is put into recording pause approx. 0.6 seconds after the LCD monitor is reopened.
PAGE 44
HDCSD800P-VQT3K35_mst.book 44 ページ [REC LAMP] ２０１０年１２月２０日月曜日午前９時４分 [OFF]/[ON] The recording lamp lights up during recording and flashes when the unit receives a signal from the remote control or when the Self-timer is counting down. When this is set to [OFF], it does not light during recording. [ALERT SOUND] [OFF]/ / Touch screen operation, starting and stopping of recording and unit on/off can be confirmed with this sound. (Volume low)/ (Volume high) 2 Beeps for 4 times When an error occurs.
PAGE 45
HDCSD800P-VQT3K35_mst.book 45 ページ [AV MULTI] ２０１０年１２月２０日月曜日午前９時４分 [COMPONENT]/[AV OUT] Please refer to page 100. [COMPONENT OUT] [480i]/[1080i] Please refer to page 100. [HDMI RESOLUTION] [AUTO]/[1080p]/[1080i]/[480p] Please refer to page 100. [VIERA Link] [OFF]/[ON] Please refer to page 101. [TV ASPECT] [16:9]/[4:3] Please refer to page 99. [3D PLAYBACK] [3D]/[2D] Please refer to page 103. [INITIAL SET] Set to [YES] for changing the menu settings back to the default condition.
PAGE 46
HDCSD800P-VQT3K35_mst.book 46 ページ２０１０年１２月２０日月曜日午前９時４分 [CARD STATUS] The used space and remaining recordable time of the SD card can be checked. ≥ When the mode switch is set to , remaining recordable time for the selected recording mode is displayed. ≥ Touch [EXIT] to close the indication. ≥ The SD card requires some space to store information and manage system files, so the actual usable space is slightly less than the indicated value.
PAGE 47
HDCSD800P-VQT3K35_mst.book 47 ページ２０１０年１２月２０日月曜日午前９時４分 Basic Using with the remote control Select the menu. MENU : [SETUP] # [REMOTE CONTROL] # [ON] 1 2 3 4 START/ STOP /VOL DATE/TIME EXT DISPLAY SEARCH PLAY SEARCH STILL ADV PAUSE STILL ADV SKIP STOP 5 6 7 8 9 10 Menu button [MENU] 11 OK button [OK] * means that these buttons function in the same manner as the corresponding buttons on the unit. Remove the insulation sheet A before using.
PAGE 48
HDCSD800P-VQT3K35_mst.book 48 ページ２０１０年１２月２０日 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. 月曜日午前９時４分 Operation of direction buttons/OK button 1 Press a direction button. STILL ADV PAUSE SKIP STOP STILL ADV SKIP MENU Replace battery with Panasonic PART NO. CR2025 only.
PAGE 49
HDCSD800P-VQT3K35_mst.book 49 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) Zoom in/out function VOL Zoom lever/Zoom button icons T side: Close-up recording (zoom in) W side: Wide-angle recording (zoom out) T W 6 W T T W ≥ Maximum zoom magnification for recording motion pictures can be set with [ZOOM MODE]. (l 61) ≥ You can also zoom by simply touching the LCD monitor.
PAGE 50
HDCSD800P-VQT3K35_mst.book 50 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) Image Stabilizer Function Use the image stabilizer to reduce the effects of shake during recording. This unit is equipped with Hybrid Optical Image Stabilizer. Hybrid Optical Image Stabilizer is a hybrid of optical and electrical image stabilizer. ≥ Please refer to page 54 for details about the Optical Image Stabilizer Lock. O.I.S. Optical image stabilizer button Press the button to turn optical image stabilizer on/ off.
PAGE 51
HDCSD800P-VQT3K35_mst.book 51 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) 1080/60p recording This is a 1080/60p (1920k1080/60 progressive) recording mode that can record in maximum quality*. * This means the highest quality for this unit. 1080/60p button To set to 1080/60p recording mode, press and hold the button until is displayed. ≥ To return to normal recording mode, press and hold the button until disappears. ≥ Please refer to page 149 for details about approximate recordable time.
PAGE 52
HDCSD800P-VQT3K35_mst.book 52 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) Recording with the Touch function You can record using convenient functions just by the easy operation of touching the screen. 1 2 Touch (left side)/ (right side) of on the Touch Menu to display Touch function icons. (l 26) (e.g. AF/AE tracking) Touch the Touch function icon. ≥ To cancel, touch the Touch function icon again. (Optical Image Stabilizer Lock is canceled by releasing the finger touching .
PAGE 53
HDCSD800P-VQT3K35_mst.book 53 ページ２０１０年１２月２０日月曜日午前９時４分 AF/AE tracking It is possible to set the focus and exposure to the subject specified on the touch screen. The focus and exposure will keep following the subject automatically even if it moves. (Dynamic tracking) 1 Touch . ≥ When [FACE RECOG.] (l 63) is [ON] and a registered face is detected, the target is automatically locked. 2 Touch the object and lock the target.
PAGE 54
HDCSD800P-VQT3K35_mst.book 54 ページ２０１０年１２月２０日月曜日午前９時４分 Optical Image Stabilizer Lock In Motion Picture Recording Mode, you can further improve optical image stabilization by touching and holding Optical Image Stabilizer Lock icon. With this function, you can further reduce the effects of the shake that tends to occur when using zoom. A Optical Image Stabilizer Lock icon 1 2 Press the Optical Image Stabilizer button to turn the image stabilizer on. Touch and hold .
PAGE 55
HDCSD800P-VQT3K35_mst.book 55 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) Recording functions of operation icons Select the operation icons to add different effects to the images to be recorded. 1 Touch (left side)/ (right side) of on the Touch Menu to display the operation icons. (l 26) ≥ Touch / downward. 2 on Touch Menu to switch pages upward or (e.g. Backlight compensation) Touch an operation icon. ≥ Select the operation icon again to cancel the function.
PAGE 56
HDCSD800P-VQT3K35_mst.book 56 ページ２０１０年１２月２０日月曜日午前９時４分 Fade When you start recording, the image/audio gradually appears. (Fade in) When you pause recording, the image/audio gradually disappears. (Fade out) ≥ The Fade setting is canceled when the recording stops. (Fade in) ∫ To select the color for Fade in/out MENU : [RECORD SETUP] # [FADE COLOR] # [WHITE] or [BLACK] (Fade out) ≥ The thumbnails of scenes recorded using fade in become black (or white).
PAGE 57
HDCSD800P-VQT3K35_mst.book 57 ページ２０１０年１２月２０日月曜日午前９時４分 Smile shot When a smiling face is detected during motion picture recording, the unit automatically records a still picture. The icon changes each time it is touched. ([ON]) # ([FACE RECOG.]) # [OFF] : : The unit records a still picture on detecting a smiling face. Still pictures are only recorded when the face of a person registered using Face Recognition (l 63) is detected. [OFF]: Cancel the setting.
PAGE 58
HDCSD800P-VQT3K35_mst.book 58 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ The available range of the flash is approx. 1 m to 2.5 m (3.3 feet to 8.2 feet) in dark places. ≥ Using the flash fixes a shutter speed to 1/500 or slower. Red-Eye Reduction Reduces the phenomena where human eyes become red from flashes. ≥ The flash is activated 2 times. ≥ The red-eye phenomenon tends to appear in certain recording conditions and more with some people than with others.
PAGE 59
HDCSD800P-VQT3K35_mst.book 59 ページ２０１０年１２月２０日月曜日午前９時４分 Tele macro A more impressive image can be obtained by focusing on the object only in close-up and shading off the background. ≥ The unit can focus on the subject at a distance of approx. 70 cm (28q). ≥ When the Tele macro is set with the zoom magnification less than 12k, it will automatically be set to 12k. ≥ Tele Macro function is canceled when the zoom magnification becomes lower than 12k.
PAGE 60
HDCSD800P-VQT3K35_mst.book 60 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) Recording functions of menus [SCENE MODE] When you record images in different situations, this mode automatically sets optimum shutter speeds and apertures.
PAGE 61
HDCSD800P-VQT3K35_mst.book 61 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ (Night scenery/Night portrait) j The shutter speed is 1/2 or more in Still Picture Recording Mode. j Using a tripod is recommended. ≥ (Night portrait) j The flash is set to [ON]. [ZOOM MODE] Set the maximum zoom ratio for the Motion Picture Recording Mode. MENU : [RECORD SETUP] # [ZOOM MODE] # desired setting [Opt.Zoom 12k]: Optical zoom only (Up to 12k) [i.
PAGE 62
HDCSD800P-VQT3K35_mst.book 62 ページ２０１０年１２月２０日月曜日午前９時４分 [TIME LAPSE REC] A scene that moves slowly for long period of time is recorded frame by frame with an interval, and is recorded as a short time motion picture. A frame is recorded with a set recording interval. 30 frames will make up motion picture of 1 second. ≥ Set [ZOOM MODE] to [Opt.Zoom 12k]. (l 61) ≥ Set [REC MODE] to [HA], [HG], [HX] or [HE].
PAGE 63
HDCSD800P-VQT3K35_mst.book 63 ページ２０１０年１２月２０日月曜日午前９時４分 [FACE RECOG.] Face Recognition is a function for finding faces that resemble faces which have already been registered and automatically prioritizing focus and exposure for those faces. This function makes it possible to keep the face of your loved ones in focus even when they are at the back or on the end of a line in a group picture. MENU : [RECORD SETUP] # [FACE RECOG.
PAGE 64
HDCSD800P-VQT3K35_mst.book 64 ページ２０１０年１２月２０日月曜日午前９時４分 Entering text Icon [A] etc. Description of operation Enters a character. Moves cursor left. Moves cursor right. [A/a] Switches between [A]/[a] (alphabet) and [&/1] (symbols/numbers). Enter a space. [Delete] Deletes a character. Deletes the previous character if the cursor is in an empty space. [Enter] Ends text entry. ≥ A maximum of 9 characters can be entered. 4 Touch [ENTER] to end registration. ≥ Touch [EXIT].
PAGE 65
HDCSD800P-VQT3K35_mst.book 65 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ Canceling a registered person 1 Select the menu. MENU : [RECORD SETUP] # [FACE RECOG.] # [SET] # [DELETE] or [DELETE ALL] ≥ Touching [DELETE ALL] cancels all the registered people. 2 (When [DELETE] is selected) Touch the person to cancel. ≥ When touched, the person is selected and touch again. ≥ Touch [ENTER]. is displayed.
PAGE 66
HDCSD800P-VQT3K35_mst.book 66 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ Prioritized face framing Prioritized face framing is displayed as orange frames. Focus and adjustment of brightness will be performed against the prioritized face framing. ≥ Prioritized face framing is only displayed with Portrait Mode in the Intelligent Auto Mode. ≥ The white frame is for face detection only.
PAGE 67
HDCSD800P-VQT3K35_mst.book 67 ページ２０１０年１２月２０日月曜日午前９時４分 [Digital Cinema Color] Recording motion pictures with more vivid colors, using x.v.Color™ technology. ≥ Switch to Manual Mode. (l 75) ≥ Set [REC MODE] to [HA], [HG], [HX] or [HE] (l 61), or set to 1080/60p recording mode. (l 51) MENU : [RECORD SETUP] # [Digital Cinema Color] # [ON] ≥ For more realistic colors, use an HDMI mini cable with a TV that supports the x.v.Color™.
PAGE 68
HDCSD800P-VQT3K35_mst.book 68 ページ２０１０年１２月２０日月曜日午前９時４分 [ZOOM MIC] Directivity of the microphone is synchronized with the zoom operation. Sounds near the front of the unit are recorded more clearly if you zoom in (close-up) and surrounding sounds are recorded more realistically if you zoom out (wide angle). ≥ Switch to Manual Mode. (l 75) MENU : [RECORD SETUP] # [ZOOM MIC] # [ON] [MIC LEVEL] When recording, the input level from the built-in microphones can be adjusted. ≥ Switch to Manual Mode.
PAGE 69
HDCSD800P-VQT3K35_mst.book 69 ページ２０１０年１２月２０日月曜日午前９時４分 [PICTURE ADJUST] Adjust the quality of the image while recording. Adjust by outputting to a TV while adjusting the quality of the image. ≥ This setting is retained when you change between Motion Picture Recording Mode and Still Picture Recording Mode. ≥ Switch to Manual Mode. (l 75) 1 Select the menu. MENU 2 3 4 : [RECORD SETUP] # [PICTURE ADJUST] Touch the desired setting items.
PAGE 70
HDCSD800P-VQT3K35_mst.book 70 ページ２０１０年１２月２０日月曜日午前９時４分 [LUMINANCE] Displays the luminance level of the center of the screen (luminance display frame) in %. It makes the adjustment of the brightness of the object easier, by checking the luminance level of the object, when recording same object in different surroundings. Adjust the brightness using [IRIS]. (l 77) ≥ Switch to Manual Mode.
PAGE 71
HDCSD800P-VQT3K35_mst.book 71 ページ２０１０年１２月２０日月曜日午前９時４分 [PICTURE SIZE] The higher the number of pixels, the higher the clarity of the picture when printing. MENU : [PICTURE] # [PICTURE SIZE] # desired setting ≥ It is possible to set from the quick menu. (l 40) ≥ The number of recording pixels that can be set changes depending on selected screen aspect ratio. (l 72) ∫ Picture size and Maximum zoom ratio Picture size 12.2M 4032k3024 7.7M 3200k2400 Aspect ratio Extra optical zoom (l 49) –* 13.
PAGE 72
HDCSD800P-VQT3K35_mst.book 72 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ This function’s default settings are 14.2M in Still Picture Recording Mode and 13.3M in Motion Picture Recording Mode. ≥ The recording will become longer depending on the recording pixels. ≥ Please refer to page 150 for details about the number of recordable pictures. [QUALITY] Selecting the picture quality. : [PICTURE] # [QUALITY] # desired setting MENU : Still pictures with a high picture quality are recorded.
PAGE 73
HDCSD800P-VQT3K35_mst.book 73 ページ２０１０年１２月２０日月曜日午前９時４分 [HI-SPEED BURST] Recording is done continuously at the rate of 60 still pictures per second. Use this function to record an object with fast movement. 1 Select the menu. MENU : [PICTURE] # [HI-SPEED BURST] # desired setting [OFF]: Cancel the setting. [60 frames/sec]: 180 still pictures are recorded continuously at the rate of 60 per second. The picture size is 2.1 M (1920k1080). 2 Press the button. ≥ flashes in red during recording.
PAGE 74
HDCSD800P-VQT3K35_mst.book 74 ページ２０１０年１２月２０日月曜日午前９時４分 [AF ASSIST LAMP] Illuminating the subject makes it easier for the camera to focus when recording in low light conditions that make focusing difficult. ≥ Switch to Manual Mode. (l 75) : [PICTURE] # [AF ASSIST LAMP] # [AUTO] MENU ≥ The available distance of the AF assist lamp is approx. 1.5 m (5 feet). ≥ A conversion lens (optional) can block the AF assist lamp, and it will become harder to adjust the focus.
PAGE 75
HDCSD800P-VQT3K35_mst.book 75 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) Manual recording ≥ The Manual Focus, White Balance, Shutter Speed, Brightness (Iris and Gain) settings are retained when you change between Motion Picture Recording Mode and Still Picture Recording Mode. Press the iA/MANUAL button to switch to Manual Mode. ≥ MNL appears on the screen.
PAGE 76
HDCSD800P-VQT3K35_mst.book 76 ページ２０１０年１２月２０日月曜日午前９時４分 White balance Automatic white balance function may not reproduce natural colors depending on the scenes or lighting conditions. If so, you can adjust the white balance manually. ≥ Press the iA/MANUAL button to switch to Manual Mode. (l 75) 1 2 MNL Touch [WB]. FOCUS WB Touch / to select White balance mode. SHTR ≥ Select the optimal mode by confirming the color on the screen. ≥ Touch [WB] to determine the mode.
PAGE 77
HDCSD800P-VQT3K35_mst.book 77 ページ２０１０年１２月２０日月曜日午前９時４分 Manual shutter speed/iris adjustment Shutter Speed: Adjust it when recording fast-moving subjects. Iris: Adjust it when the screen is too bright or too dark. ≥ Press the iA/MANUAL button to switch to Manual Mode. (l 75) 1 2 Touch [SHTR] or [IRIS]. Touch / to adjust settings. ≥ Touch [SHTR]/[IRIS] to complete the adjustments.
PAGE 78
HDCSD800P-VQT3K35_mst.book 78 ページ２０１０年１２月２０日月曜日午前９時４分 Manual focus adjustment If auto focusing is difficult due to the conditions, then use Manual Focus. ≥ Press the iA/MANUAL button to switch to Manual Mode. (l 75) 1 (When MF assist function is used) Select the menu. MENU : [RECORD SETUP] # [MF ASSIST] # [ON] ≥ It is possible to set from the quick menu. (l 40) ≥ Touch 2 3 to display the Manual icon. Touch [FOCUS]. Touch [MF] to change to Manual Focus. ≥ MF appears on the screen.
PAGE 79
HDCSD800P-VQT3K35_mst.book 79 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Recording) Recording 3D video With the 3D Conversion Lens (optional) attached, you can record life-like and powerful 3D video. To view 3D video, a television that supports 3D is required. 3D video The image is an illustration. ≥ In the unit, the recordable 3D videos are side-by-side format (2-screen structure). ≥ Since the 3D video is recorded in side-by-side format, the recorded 3D video is not of high definition picture quality.
PAGE 80
HDCSD800P-VQT3K35_mst.book 80 ページ 4 ２０１０年１２月２０日午前９時４分 Touch [EXIT] to end the adjustment. ≥ After adjustment, a single screen appears. ≥ When re-attaching the 3D Conversion Lens or after an impact etc., it is recommended that you perform the adjustment again.  A 5 月曜日 3D 3D 0h00m00s HG R 1h20m appears. Press the recording start/stop button to start recording. ≥ Start recording after removing the Lens front cap.
PAGE 81
HDCSD800P-VQT3K35_mst.book 81 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ Functions that cannot be used during 3D recording When recording with the 3D Conversion Lens, you cannot use certain functions.
PAGE 82
HDCSD800P-VQT3K35_mst.book 82 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Playback) Playback Operations Motion picture playback using operation icon For details on the basic playback operations, refer to page 36. Playback operation Playback display Operating steps Fast forward/ rewind playback Touch 5 during playback to fast forward. (Touch 6 to rewind.) ≥ The fast forward/rewind speed increases if you touch 5/6 again. (The display on the screen changes from 5 to .
PAGE 83
HDCSD800P-VQT3K35_mst.book 83 ページ Playback operation Direct playback ２０１０年１２月２０日 Playback display During Playback 月曜日午前９時４分 Operating steps Touch the Direct playback bar or slide it while touching. ≥ The playback pauses temporarily and skips to the position touched or slid to while touching. ≥ Playback will start by releasing your touching or sliding finger. ≥ Direct playback bar cannot be operated with the remote control.
PAGE 84
HDCSD800P-VQT3K35_mst.book 84 ページ２０１０年１２月２０日月曜日午前９時４分 Highlight&Time frame index An image of one scene is displayed as a thumbnail at set search condition. Scene can be played back from any midway point of the scene you wish to see. ≥ Operate the zoom lever to side and change over the thumbnail display to Highlight&Time frame index. (l 37) 1 Touch . ≥ To display the next (previous) page: j Slide the thumbnail display upward (downward) while touching it.
PAGE 85
HDCSD800P-VQT3K35_mst.book 85 ページ２０１０年１２月２０日月曜日午前９時４分 Resuming the previous playback If playback of a scene was stopped halfway, the playback can be resumed from where it was stopped. MENU : [VIDEO SETUP] # [RESUME PLAY] # [ON] If playback of a motion picture is stopped, appears on the thumbnail view of the stopped scene. ≥ The memorized resume position is cleared if you turn off the unit or change the mode. (The setting of [RESUME PLAY] does not change.
PAGE 86
HDCSD800P-VQT3K35_mst.book 86 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Playback) Various playback functions Playing back motion pictures/still pictures by date The scenes or the still pictures recorded on the same day can be played back in succession. 1 2 Touch the date select icon. (l 26) Touch the playback date.  ALL The scenes or the still pictures recorded on the date selected are displayed as thumbnails. 3 Touch the scene or the still picture to be played back.
PAGE 87
HDCSD800P-VQT3K35_mst.book 87 ページ２０１０年１２月２０日月曜日午前９時４分 Highlight Playback Part that was recognized as clearly recorded is extracted from a long recording, and it can be played back in a short time with effects and music added. ≥ Highlight playback cannot be used for iFrame scenes. 1 Touch 2 (Only when you would like to change the settings) . (l 26) ALL Touch [SET] to select the item to change. [SCENE SETUP]: Select the scene or date to be played back.
PAGE 88
HDCSD800P-VQT3K35_mst.book 88 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ Priority setting 1 Touch [FACE] or [FACE RECOG.]. ≥ If you touch [FACE], any detected face, including the face of person registered for Face Recognition, is given priority on playback. 2 (When [FACE RECOG.] is selected) Touch a face to specify. 1 2 3 4 5 6 KEN ANNA MARY ≥ You can specify up to 6 faces, which are to be played back in priority. ≥ When touched, the registered face is selected and surrounded JOE by red.
PAGE 89
HDCSD800P-VQT3K35_mst.book 89 ページ２０１０年１２月２０日月曜日午前９時４分 Changing the playback settings and playing back the slide show 1 Touch . (l 26) ALL 2 (Only when you would like to change the settings) Touch [SET] to select the item to change. [DATE SETUP]: Select the date to be played back. [EFFECT SETUP]: Select the effect for playback. (l 88) [SLIDE INTERVAL]: Selects the interval between still pictures at playback. [MUSIC SELECT]: Select the music to be played on playback.
PAGE 90
HDCSD800P-VQT3K35_mst.book 90 ページ２０１０年１２月２０日月曜日午前９時４分 (When [MUSIC SELECT] is selected) Touch the desired sound. ≥ To adjust the volume of music during playback of the slide show or audio testing, operate the volume lever. (l 37) ≥ Touch [ENTER]. (To test the music audio) Touch [START] and start the audio testing. ≥ Touch the other music option to change the music to be tested. ≥ When you touch [STOP], the music playback stops. 4 5 Touch [START]. Select the playback operation.
PAGE 91
HDCSD800P-VQT3K35_mst.book 91 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Playback) Deleting scenes/still pictures Deleted scenes/still pictures cannot be restored, so perform appropriate confirmation of the contents before proceeding with deletion. ¬ Change the mode to . ∫ To delete the scene or still picture being played back Touch while scenes or still pictures to be deleted are being played back.
PAGE 92
HDCSD800P-VQT3K35_mst.book 92 ページ２０１０年１２月２０日月曜日午前９時４分 When you stop deleting halfway Touch [CANCEL] while deleting. ≥ The scenes or still pictures that have already been deleted when the deletion is canceled cannot be restored. To complete editing Touch [Return]. ≥ You can also delete scenes by touching [MENU], selecting [EDIT SCENE] # [DELETE] # [ALL SCENES], [MULTI] or [SINGLE]. ≥ You can also delete still pictures by touching [MENU], selecting [PICT.
PAGE 93
HDCSD800P-VQT3K35_mst.book 93 ページ２０１０年１２月２０日月曜日午前９時４分 To delete all the divided points MENU : [EDIT SCENE] # [DIVIDE] # [CANCEL ALL] ≥ The scenes that were deleted after division cannot be recovered. ≥ You cannot divide a scene if you are playing back a disc with a DVD burner (optional) connected, or if the number of scenes of a given date would exceed 99 scenes. ≥ It may not be possible to divide scenes with a short recording time.
PAGE 94
HDCSD800P-VQT3K35_mst.book 94 ページ２０１０年１２月２０日月曜日午前９時４分 Deleting personal information Deletes face recognition information from scenes in which faces were recognized. ≥ Change the mode to and touch the play mode select icon. Then set [VIDEO/ PICTURE] to [1080/60p] or [AVCHD]. (l 36) ≥ Personal information is not recorded in the iFrame scenes. 1 Select the menu. MENU 2 : [VIDEO SETUP] # [DELETE PERSONAL INFO] Touch the desired scenes with personal information to be deleted.
PAGE 95
HDCSD800P-VQT3K35_mst.book 95 ページ２０１０年１２月２０日月曜日午前９時４分 Protecting scenes/still pictures Scenes/still pictures can be protected so that they are not deleted by mistake. (Even if you protect some scenes/still pictures, formatting the media will delete them.) ≥ Change the mode to . 1 Select the menu. MENU 2 : [VIDEO SETUP] or [PICT. SETUP] # [SCENE PROTECT] Touch the scene/still picture to be protected. ≥ When touched, the scene/still picture is selected and the indication appears on the thumbnail.
PAGE 96
HDCSD800P-VQT3K35_mst.book 96 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Playback) DPOF setting You can write the data selecting still pictures to be printed and the number of prints (DPOF data) onto the SD card. ¬ Change the mode to and touch the play mode select icon. Then set [VIDEO/PICTURE] to [PICTURE].
PAGE 97
HDCSD800P-VQT3K35_mst.book 97 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Playback) Watching Video/Pictures on your TV Confirm the terminals on your TV and use a cable compatible with the terminals. Image quality may vary with the connected terminals. A High quality 1 HDMI terminal 2 Component terminal 3 Video terminal ≥ Use the AV multi cable (supplied) or HDMI mini cable (optional) and check the output settings. (l 100) ≥ HDMI is the interface for digital devices.
PAGE 98
HDCSD800P-VQT3K35_mst.book 98 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ Check that the plugs are inserted as far as they go. ≥ Always use a genuine Panasonic HDMI mini cable (RP-CDHM15, RP-CDHM30; optional). ≥ Do not use any other AV multi cables except the supplied one. ≥ When connecting to the component terminal of the TV, the yellow plug of the AV multi cable is not required. ≥ When connecting to the AV terminal of the TV, do not connect the component terminal plug of the AV multi cable.
PAGE 99
HDCSD800P-VQT3K35_mst.book 99 ページ２０１０年１２月２０日 ∫ To watch images on a regular TV (4:3) or when both sides of the images do not appear on the screen Change the menu setting to display the images correctly. (Check the TV setting.) MENU : [SETUP] # [TV ASPECT] # [4:3] 月曜日午前９時４分 ∫ To display the on-screen information on the TV When the EXT DISPLAY button on the remote control is pressed, the information displayed on the screen (operation icon and time code etc.) can be displayed/not displayed on the TV.
PAGE 100
HDCSD800P-VQT3K35_mst.book 100 ページ２０１０年１２月２０日月曜日午前９時４分 Connecting with a HDMI mini cable Select the desired method of HDMI output. MENU : [SETUP] # [HDMI RESOLUTION] # [AUTO]/[1080p]/[1080i]/[480p] ≥ [AUTO] determines the output resolution automatically based on information from the connected TV. If the images are not output on the TV when the setting is [AUTO], switch to the method [1080p], [1080i] or [480p] which enables the images to be displayed on your TV.
PAGE 101
HDCSD800P-VQT3K35_mst.book 101 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Playback) Playback using VIERA Link™ What is the VIERA Link (HDAVI Control™)? ≥ VIERA Link™ is a new name for EZ Sync™. ≥ This function allows you to use your remote control for the Panasonic TV for easy operations when this unit has been connected to a VIERA Link compatible device using a HDMI mini cable (optional) for automatic linked operations. (Not all operations are possible.
PAGE 102
HDCSD800P-VQT3K35_mst.book 102 ページ 3 ２０１０年１２月２０日月曜日午前９時４分 Operate with the remote control for the TV. 1) 2)     1) Press the button up, down, left or right to select a scene or still picture to be played back, and then press the button in the center to set it. 2) Activate the operation icons that are displayed on TV screen with the remote control for the TV.
PAGE 103
HDCSD800P-VQT3K35_mst.book 103 ページ２０１０年１２月２０日月曜日午前９時４分 Advanced (Playback) 3D video playback Connect the unit to a 3D compatible television and play back scenes recorded in 3D to enjoy life-like and powerful 3D video. ¬ Change the mode to and touch the play mode select icon. Then set [VIDEO/PICTURE] to [AVCHD]. (l 36) 1 Select the menu. MENU : [SETUP] # [3D PLAYBACK] # [3D] [3D]: Play back scenes recorded in 3D in unaltered form as 3D video.
PAGE 104
HDCSD800P-VQT3K35_mst.book 104 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ You cannot play back 3D video on the LCD monitor of the unit. When you play back scenes recorded in 3D on the LCD monitor, they will be played back in 2D. ≥ You can also play back scenes recorded in 3D by date. Even if scenes are recorded on the same day, the unit will display the date separately when switching between 2D and 3D recordings.
PAGE 105
HDCSD800P-VQT3K35_mst.book 105 ページ２０１０年１２月２０日月曜日午前９時４分 Copy/Dubbing Copy/Dubbing Connecting a DVD burner to copy to/ play back a disc Motion pictures or still pictures recorded with this unit can be copied to a DVD disc by connecting a DVD burner (optional) to this unit using a USB Connection Cable (supplied with DVD burner). The copied DVD disc can also be played back. ≥ Please read the operating instructions of the DVD burner for how to use it.
PAGE 106
HDCSD800P-VQT3K35_mst.book 106 ページ 1 ２０１０年１２月２０日月曜日午前９時４分 Connect the AC adaptor (supplied with DVD burner) to the DVD burner. ≥ You cannot supply power to the DVD burner from this unit. 2 3 Connect this unit to the AC adaptor and change the mode to Connect this unit to the DVD burner with the USB Connection Cable (supplied with DVD burner). A USB Connection Cable (supplied with DVD burner) B DVD burner (optional) ≥ Insert the plugs as far as they will go. 4 Insert the disc in the DVD burner.
PAGE 107
HDCSD800P-VQT3K35_mst.book 107 ページ２０１０年１２月２０日月曜日午前９時４分 Copying to discs ≥ You cannot copy from multiple SD cards to 1 disc. (You can additionally copy only to a DVD-RAM.) ≥ You cannot copy motion pictures together with still pictures or motion pictures in a different picture quality (AVCHD picture quality and conventional normal picture quality) to the same disc. ≥ iFrame scenes cannot be copied to disc. Copy to PC to make a backup.
PAGE 108
HDCSD800P-VQT3K35_mst.book 108 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ About recording formats when copying motion pictures [AVCHD] ([HA]/[HG]/[HX]/[HE]): Copying scenes of 1080/60p picture quality The scenes recorded in 1080/60p by this unit will be copied after converting to AVCHD picture quality. When copying scenes recorded in 1080/60p, select the recording picture quality ([HA]/ [HG]/[HX]/[HE]).
PAGE 109
HDCSD800P-VQT3K35_mst.book 109 ページ２０１０年１２月２０日月曜日午前９時４分 Approximate time for copying to a disc To copy motion pictures to the full capacity of a disc Copy time Disc type [AVCHD] DVD-RAM Approx. 50 min to 1 h 20 min DVD-RW*/ +RW* Approx. 35 min to 1 h 15 min DVD-R*/+R* Approx. 15 min to 45 min [Standard] ([XP]) [Standard] ([SP]) Approx. 1 h 30 min to 2 h 30 min Approx.
PAGE 110
HDCSD800P-VQT3K35_mst.book 110 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ The disc that was copied to can be played back by connecting this unit and a DVD burner. ≥ Do not turn off this unit or the DVD burner or disconnect the USB Connection Cable while copying. Also, do not shake this unit or the DVD burner. ≥ It is impossible to stop copying halfway. ≥ The order in which the scenes were copied cannot be changed. ≥ Data that has been recorded on another device may not be copied.
PAGE 111
HDCSD800P-VQT3K35_mst.book 111 ページ２０１０年１２月２０日月曜日午前９時４分 Managing the copied disc ≥ Connect this unit to the DVD burner and then touch [PLAY DISC]. (l 106) ∫ Formatting discs This is for initializing DVD-RAM, DVD-RW and +RW discs. Please be aware that if a disc is formatted, then all the data recorded on the disc will be erased. Back up important data on a PC etc. MENU : [DISC SETUP] # [FORMAT DISC] ≥ When formatting is complete, touch [EXIT] to exit the message screen.
PAGE 112
HDCSD800P-VQT3K35_mst.book 112 ページ２０１０年１２月２０日月曜日午前９時４分 Copy/Dubbing Dubbing with a Blu-ray disc recorder, video device, etc. ∫ Check before dubbing Check the equipment used for dubbing.
PAGE 113
HDCSD800P-VQT3K35_mst.book 113 ページ２０１０年１２月２０日月曜日午前９時４分 Dubbing in high-definition picture quality You can dub using a Panasonic Blu-ray disc recorder or high-definition (AVCHD) compatible DVD recorder. ≥ Depending on the recorders or the media to be copied to, you may not be able to copy in high-definition (AVCHD) picture quality. For further details, see the operating instructions of your recorder. ≥ Note that the equipment described may not be available in certain countries and regions.
PAGE 114
HDCSD800P-VQT3K35_mst.book 114 ページ 2 ２０１０年１２月２０日月曜日午前９時４分 Touch [RECORDER] on the screen of this unit. ≥ When you select an option other than [RECORDER], reconnect the USB cable. ≥ When using the battery, the LCD monitor turns off after about 5 seconds. Touch the screen to turn the LCD monitor on. 3 Dubbing through operations on the Blu-ray disc recorder or highdefinition (AVCHD) compatible DVD recorder.
PAGE 115
HDCSD800P-VQT3K35_mst.book 115 ページ２０１０年１２月２０日月曜日午前９時４分 Dubbing in standard picture quality ∫ Dubbing using equipment without an SD card slot or a USB terminal, or using a video device You can dub by connecting an AV multi cable. ≥ Images are dubbed in standard quality. ≥ Use the AC adaptor to free you from worrying about the battery running down. Change the video input on the video device and TV that this unit is connected to.
PAGE 116
HDCSD800P-VQT3K35_mst.book 116 ページ２０１０年１２月２０日月曜日午前９時４分 Copy/Dubbing 3D video storage You can store 3D video with a DVD burner, a video device or a PC. Copying with a DVD burner ≥ Please refer to page 105 for details about copying with a DVD burner. ∫ Copying unaltered as 3D video Recording format: [AVCHD] The scenes recorded in 3D using the unit can be copied and stored in unaltered form as 3D video.The video is recorded unaltered in side-by-side format.
PAGE 117
HDCSD800P-VQT3K35_mst.book 117 ページ２０１０年１２月２０日月曜日午前９時４分 Using HD Writer AE 3.0 ≥ Please refer to page 118 for details about copying with HD Writer AE 3.0. When you use HD Writer AE 3.0 to handle scenes recorded in 3D, the following operations are possible. j Copying data to a PC (Scenes recorded in 3D will be copied unaltered as 3D video.) j Copying in BD/AVCHD format (Scenes recorded in 3D will be copied unaltered as 3D video.
PAGE 118
HDCSD800P-VQT3K35_mst.book 118 ページ２０１０年１２月２０日月曜日午前９時４分 With a PC What you can do with a PC HD Writer AE 3.0 You can copy the motion/still picture data to the HDD of PCs or write to media like Blu-ray discs, DVD discs or SD cards using HD Writer AE 3.0, the software installed in the supplied CD-ROM. Refer to the operating instructions of HD Writer AE 3.0 (PDF file) for details on how to use it.
PAGE 119
HDCSD800P-VQT3K35_mst.book 119 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ It is possible to play back on a PC using a image viewer standard to Windows or commercially available image browsing software, and copy pictures to a PC using Windows Explorer. ≥ Please refer to page 130 for details about using a Mac. Important Notice ≥ When using an SDXC Memory Card, check the following support site. http://panasonic.net/avc/sdcard/information/SDXC.html ≥ Do not insert a disc recorded in AVCHD format with HD Writer AE 3.
PAGE 120
HDCSD800P-VQT3K35_mst.book 120 ページ２０１０年１２月２０日月曜日午前９時４分 End User License Agreement Before opening the CD-ROM package, please read the following. You (“Licensee”) are granted a license for the Software defined in this End User License Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement.
PAGE 121
HDCSD800P-VQT3K35_mst.book 121 ページ２０１０年１２月２０日月曜日午前９時４分 With a PC Operating environment ≥ Even if the system requirements mentioned in this owner’s manual are fulfilled, some PCs cannot be used. ≥ A CD-ROM drive is necessary to install the supplied software applications. (A compatible Blu-ray disc/DVD writer drive and media are necessary for writing to a Blu-ray disc/DVD.) ≥ Operation is not guaranteed in the following cases.
PAGE 122
HDCSD800P-VQT3K35_mst.book 122 ページ２０１０年１２月２０日月曜日午前９時４分 Display High Color (16 bit) or more (32 bit or more recommended) Desktop resolution of 1024k768 pixels or more (1920k1080 pixels or more recommended) Windows 7/Windows Vista: DirectX 9.0c compatible video card (DirectX 10 recommended) Windows XP: DirectX 9.
PAGE 123
HDCSD800P-VQT3K35_mst.book 123 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ Operating environment for the card reader function (mass storage) PC IBM PC/AT compatible PC OS Windows 7 (32 bit/64 bit) Windows Vista (32 bit) (SP1/SP2) Windows XP (32 bit) (SP3) CPU Windows 7/Windows Vista: 1.
PAGE 124
HDCSD800P-VQT3K35_mst.book 124 ページ２０１０年１２月２０日月曜日午前９時４分 With a PC Installation When installing the software, log on to your computer as the Administrator or with a user name with equivalent authorization. (If you do not have authorization to do this, consult your manager.) ≥ Before starting the installation, close all applications that are running. ≥ Do not perform any other operations on your PC while the software is being installed. ≥ Explanation of operations and screens is based on Windows 7.
PAGE 125
HDCSD800P-VQT3K35_mst.book 125 ページ 7 ２０１０年１２月２０日月曜日午前９時４分 When installation is complete, some notes will appear. Check the contents, then close the window. 8 Select [Yes, I want to restart my computer now.], then click [Finish]. The PC must be rebooted for the application to work. ∫ Uninstalling HD Writer AE 3.0 Follow the steps below to uninstall any software applications that you no longer require. 1 Select [Start] # [Control Panel] # [Uninstall a program]. 2 Select [HD Writer AE 3.
PAGE 126
HDCSD800P-VQT3K35_mst.book 126 ページ２０１０年１２月２０日月曜日午前９時４分 With a PC Connecting to a PC ≥ Connect this unit to the PC after the software applications are installed. ≥ Remove the supplied CD-ROM from your PC. A USB cable (supplied) ≥ Insert the plugs as far as they will go. 1 Connect this unit to the AC adaptor. ≥ It is possible to use the unit connected to the PC with the batteries only, but you will not be able to write data into the unit.
PAGE 127
HDCSD800P-VQT3K35_mst.book 127 ページ２０１０年１２月２０日月曜日午前９時４分 ≥ Do not use any other USB cables except the supplied one. (Operation is not guaranteed with any other USB cables.) ≥ When the unit is connected to a PC, it cannot be turned off. Disconnect the USB cable, before turning this unit off. ≥ When performing reading/writing between a PC and an SD card, be aware that some SD card slots built into PCs and some SD card readers are not compatible with the SDHC Memory Card or SDXC Memory Card.
PAGE 128
HDCSD800P-VQT3K35_mst.book 128 ページ２０１０年１２月２０日月曜日午前９時４分 About the PC display When the unit is connected to a PC, it is recognized as an external drive. ≥ Removable disk (Example: ) is displayed in [Computer]. We recommend using HD Writer AE 3.0 to copy or write back motion picture data. Using Windows Explorer or other programs on the PC to copy, move or rename files and folders recorded with this unit will result in them being unusable with HD Writer AE 3.0.
PAGE 129
HDCSD800P-VQT3K35_mst.book 129 ページ２０１０年１２月２０日月曜日午前９時４分 With a PC Starting HD Writer AE 3.0 ≥ To use the software, log on as an Administrator or as user name for standard user account (only for Windows 7/Windows Vista). The software cannot be used with the user name for a guest account. (On the PC) Select [Start] # [All Programs] # [Panasonic] # [HD Writer AE 3.0] # [HD Writer AE]. ≥ For details on how to use the software applications, read the PDF operating instructions of the software.
PAGE 130
HDCSD800P-VQT3K35_mst.book 130 ページ２０１０年１２月２０日月曜日午前９時４分 With a PC If using Mac ≥ HD Writer AE 3.0 is not available for Mac. ≥ iMovie’11 supported. For details about iMovie’11, please contact Apple Inc. ≥ 1080/60p scenes cannot be imported to a Mac. ≥ Since iMovie’11 is not compatible with 1080/60p, it cannot acquire the scenes recorded in 1080/60p. Record in normal recording mode when importing to Mac. ≥ There are some limitations in the functions when iMovie’11 is used.
PAGE 131
HDCSD800P-VQT3K35_mst.book 131 ページ２０１０年１２月２０日月曜日午前９時４分 Others Indications ∫ Recording indications Motion Picture Recording Mode 0h00m00s Still Picture Recording Mode 1h30m R 1h20m +1  R 3000 1h30m +1 14.
PAGE 132
HDCSD800P-VQT3K35_mst.
PAGE 133
HDCSD800P-VQT3K35_mst.book 133 ページ２０１０年１２月２０日 ∫ Playback indications 1/;/5/ /6/ D/E/;1/2; /7/8/9/:/ 0h00m00s Playback Time (l 36) Scene Number Repeat Playback (l 84) Accessing the card (l 114, 127) ∫ Confirmatory indications –– (Time display) The built-in battery is low. (l 27) Resume Playback (l 85) 100-0001 1 午前９時４分 ∫ Indication of connection to other devices Display during playback (l 36, 82) No.
PAGE 134
HDCSD800P-VQT3K35_mst.book 134 ページ２０１０年１２月２０日月曜日午前９時４分 Others Messages Major confirmation/error messages to be indicated on the screen in text. CHECK CARD. This card is not compatible or it cannot be recognized by the unit. If this message appears even though motion pictures and still pictures are recorded on an SD card, the card may be unstable. Reinsert the SD card, then turn the unit off and then on again. THIS BATTERY CANNOT BE USED. ≥ Use a battery that is compatible with this unit.
PAGE 135
HDCSD800P-VQT3K35_mst.book 135 ページ２０１０年１２月２０日月曜日午前９時４分 About recovery If faulty management information is found, the messages may appear and a repair is performed. (Repairing may take time depending on the error.) SOME SCENES NEED REPAIRING. PLAY SCENES TO BE REPAIRED. (IRREPARABLE SCENES WILL BE DELETED.) ≥ The above message is displayed when abnormal management information is detected when the scenes are displayed in thumbnail.
PAGE 136
HDCSD800P-VQT3K35_mst.book 136 ページ２０１０年１２月２０日月曜日午前９時４分 Others Troubleshooting Power Problem This unit cannot be turned on. This unit does not stay on long enough. Battery runs down quickly. Check points ≥ Charge the battery again to ensure it is sufficiently charged. (l 20) ≥ In cold places, the battery using time becomes shorter. ≥ The battery has a limited life. If the operating time is still too short even after the battery is fully charged, the battery has worn out and needs to be replaced.
PAGE 137
HDCSD800P-VQT3K35_mst.book 137 ページ２０１０年１２月２０日月曜日午前９時４分 Indication Problem Remaining battery indication is not displayed properly. Check points ≥ The remaining battery capacity indication is an approximation. If the remaining battery capacity indication is not displayed correctly, fully charge the battery, discharge it and then charge it again. Recording Problem Check points The unit arbitrarily stops recording. ≥ Use an SD card that can be used for motion picture recording.
PAGE 138
HDCSD800P-VQT3K35_mst.book 138 ページ２０１０年１２月２０日月曜日午前９時４分 Playback Problem Check points Scenes/still pictures cannot be played back. ≥ Any scenes/still pictures where the thumbnails are displayed as cannot be played back. Scenes cannot be deleted. ≥ Release the protect setting. (l 95) ≥ Any scenes/still pictures where the thumbnails are displayed as cannot be deleted. If the scenes/still pictures are unnecessary, format the media to erase the data.
PAGE 139
HDCSD800P-VQT3K35_mst.book 139 ページ２０１０年１２月２０日月曜日午前９時４分 With other products Problem Although this unit is correctly connected to a TV, images cannot be seen. The images are squeezed horizontally. Check points ≥ Please read the operating instructions of your TV and select the channel that matches the input used for the connection. ≥ Change the [TV ASPECT] setting to match the aspect ratio of the TV. (l 99) ≥ Change the setting of the unit depending on the cable connecting to the TV.
PAGE 140
HDCSD800P-VQT3K35_mst.book 140 ページ２０１０年１２月２０日月曜日午前９時４分 With a PC Problem Check points When connected by the USB cable, this unit is not detected by the PC. ≥ After re-inserting the SD card into the unit, reconnect the supplied USB cable. ≥ Select another USB terminal on the PC. ≥ Check the operating environment. (l 121,130) ≥ Connect the supplied USB cable again after restarting the PC and turning on this unit again. When the USB cable is disconnected, an error message will appear on the PC.
PAGE 141
HDCSD800P-VQT3K35_mst.book 141 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ If scenes do not change smoothly when played back on another device (AVCHD, 1080/60p) The images may be still for several seconds at the joins between the scenes if the following operations are performed when multiple scenes have been continuously played back using another unit. ≥ Just how smoothly the scenes will be played back depends on the playback unit.
PAGE 142
HDCSD800P-VQT3K35_mst.book 142 ページ２０１０年１２月２０日月曜日午前９時４分 Others Cautions for use About this unit The unit and the SD card become warm during use. This is not a malfunction. Keep this unit as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). ≥ If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be disrupted by electromagnetic wave radiation.
PAGE 143
HDCSD800P-VQT3K35_mst.book 143 ページ２０１０年１２月２０日 Do not use the unit for surveillance purposes or other business uses. ≥ This unit was designed for consumer intermittent use. It was not intended for continuous use, or for any industrial or commercial application resulting in prolonged use. ≥ In certain situations, continuous use could cause the unit to overheat and cause a malfunction. Such use is strongly discouraged.
PAGE 144
HDCSD800P-VQT3K35_mst.book 144 ページ２０１０年１２月２０日 About the AC adaptor ≥ If the temperature of the battery is extremely high or extremely low, charging may take time or the battery may not be charged. ≥ If you use the AC adaptor near a radio, radio reception may be disturbed. Keep the AC adaptor 1 m (3.3 feet) or more away from the radio. ≥ When using the AC adaptor, it may generate whirring sounds. However, this is normal. ≥ After use, be sure to disconnect the AC adaptor.
PAGE 145
HDCSD800P-VQT3K35_mst.book 145 ページ２０１０年１２月２０日 About 3D About 3D recording Attach the 3D Conversion Lens securely. It must not be used with an insecure attachment. Do not use the 3D Conversion Lens without adjusting it first. ≥ It will not be possible to record 3D video correctly, and this may lead to tiredness or discomfort. ≥ When you re-attach the 3D Conversion Lens after removing it, we recommend making the adjustments again.
PAGE 146
HDCSD800P-VQT3K35_mst.book 146 ページ２０１０年１２月２０日 About the SD card When disposing of or giving away the SD card, note that: ≥ Formatting and deletion of this unit or computer only changes the file management information and does not completely delete the data in the SD card. ≥ It is recommended that the SD card is physically destroyed or the SD card is physically formatted using this unit when disposing of or giving away the SD card.
PAGE 147
HDCSD800P-VQT3K35_mst.book 147 ページ２０１０年１２月２０日 About personal information After you have set up the face recognition function, personal information will be held in this unit and included in recorded images. ≥ When the unit is serviced, or given away/ disposed of, the personal information should be deleted in the interests of protecting personal information.
PAGE 148
HDCSD800P-VQT3K35_mst.book 148 ページ２０１０年１２月２０日月曜日午前９時４分 Others About copyright ∫ Carefully observe copyright laws Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights. ∫ Licenses ≥ SDXC Logo is a trademark of SD-3C, LLC. ≥ “AVCHD” and the “AVCHD” Logo are trademarks of Panasonic Corporation and Sony Corporation.
PAGE 149
HDCSD800P-VQT3K35_mst.book 149 ページ２０１０年１２月２０日月曜日午前９時４分 Others Recording modes/approximate recordable time ≥ SD cards are only mentioned with their main memory size. The stated times are the approximate recordable times for continuous recording.
PAGE 150
HDCSD800P-VQT3K35_mst.book 150 ページ２０１０年１２月２０日月曜日午前９時４分 Others Approximate number of recordable pictures ≥ SD cards are only mentioned with their main memory size. The stated number is the approximate number of recordable pictures. (When [ASPECT RATIO] is set to [4:3] and [QUALITY] is set to Picture size SD card 4 GB 16 GB 64 GB 12.2M 4032k3024 610 2500 10000 7.7M 3200k2400 940 3900 15800 4.9M SD card 4 GB 16 GB 64 GB 14.2M 4608k3072 500 2100 8400 8.6M 3600k2400 850 3400 14000 13.3M 8.
PAGE 151
HDCSD800P-VQT3K35_mst.book 151 ページ２０１０年１２月２０日月曜日午前９時４分 Others Specifications High Definition Video Camera Information for your safety Power source: DC 9.3 V (When using AC adaptor) DC 7.2 V (When using battery) Power consumption: Recording; 5.8 W Charging; 10.1 W Signal system: 1080/60p, 1080/60i, 540/30p Recording format: [1080/60p]; Original format [HA]/[HG]/[HX]/[HE]; AVCHD format compliant [iFrame]; MPEG-4 AVC file format complaint (.MP4) Image sensor: 1/4.
PAGE 152
HDCSD800P-VQT3K35_mst.book 152 ページ２０１０年１２月２０日月曜日午前９時４分 Filter diameter: 46 mm Zoom: 12k Optical Zoom, 20k i.Zoom, 30k/700k Digital Zoom Image Stabilizer function: Optical (Hybrid Optical Image Stabilizer, Active mode, Optical Image Stabilizer Lock function) Monitor: 3z wide LCD monitor (Approx.
PAGE 153
HDCSD800P-VQT3K35_mst.book 153 ページ２０１０年１２月２０日月曜日午前９時４分 Flash: Available range; Approx. 1.0 m to 2.5 m (3.3 feet to 8.2 feet) Dimensions: 63 mm (W)k66 mm (H)k133 mm (D) [2.48 q (W)k2.60 q (H)k5.24 q (D)] (excluding projecting parts) Mass (Weight): Approx. 330 g (Approx. 0.73 lbs.) [without battery (supplied) and an SD card (optional)] Mass (Weight) in operation: Approx. 396 g (Approx. 0.87 lbs.
PAGE 154
HDCSD800P-VQT3K35_mst.book 154 ページ２０１０年１２月２０日月曜日 ∫ Motion pictures Recording media: SD Memory Card (FAT12 and FAT16 system compliant) SDHC Memory Card (FAT32 system compliant) SDXC Memory Card (exFAT system compliant) Refer to page 22 for details on SD cards usable in this unit. Compression: MPEG-4 AVC/H.264 Recording mode and transfer rate: [1080/60p]; Approx. 28 Mbps (VBR) [HA]; Approx. 17 Mbps (VBR) [HG]; Approx. 13 Mbps (VBR) [HX]; Approx. 9 Mbps (VBR) [HE]; Approx. 5 Mbps (VBR) [iFrame]; Approx.
PAGE 155
HDCSD800P-VQT3K35_mst.book 155 ページ２０１０年１２月２０日月曜日午前９時４分 AC adaptor Information for your safety Power source: Power consumption: DC output: AC 110 V to 240 V, 50/60 Hz 16 W DC 9.3 V, 1.2 A Dimensions: 52 mm (W)k26 mm (H)k86.3 mm (D) [2.1 q (W)k1.0 q (H)k3.4 q (D)] Mass (Weight): Approx. 115 g (Approx. 0.25 lbs.) Specifications may change without prior notice.
PAGE 156
HDCSD800P-VQT3K35_mst.book 156 ページ２０１０年１２月２０日月曜日午前９時４分 Others Optional accessories Accessory No.
PAGE 157
HDCSD800P-VQT3K35_mst.book 157 ページ Accessory No.
PAGE 158
HDCSD800P-VQT3K35_mst.book 158 ページ２０１０年１２月２０日 ∫ Attaching the conversion lens/ filter kit Attach the wide conversion lens (VW-W4607H; optional), the wide end conversion lens (VW-WE08H; optional), ND filter or MC protector of the Filter kit (VW-LF46N; optional) in front of the lens. ≥ It is not possible to attach it to the front of the lens hood. (l 29) ≥ You will not be able to use the flash. Set the flash setting to ([OFF]). (l 57) Be careful about the following.
PAGE 159
HDCSD800P-VQT3K35_mst.book 159 ページ２０１０年１２月２０日月曜日午前９時４分 Accessory Order Form (For USA and Puerto Rico Customers) Please photocopy this form when placing an order. 1. Model # 2. Items Ordered Accessory # Description Price Each Quantity Total Price Subtotal Your State & Local Sales Tax Shipping & Handling 6.95 Total Enclosed 3. Method of payment (check one) Check of Money Order enclosed (NO C.O.D.
PAGE 160
HDCSD800P-VQT3K35_mst.book 160 ページ２０１０年１２月２０日月曜日午前９時４分 Others Limited Warranty (ONLY FOR U.S.A.
PAGE 161
HDCSD800P-VQT3K35_mst.book 161 ページ２０１０年１２月２０日月曜日午前９時４分 THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content.
PAGE 162
HDCSD800P-VQT3K35_mst.book 162 ページ２０１０年１２月２０日月曜日午前９時４分 Index ∫ Numerics 1080/60p . . . . . . . . . . . . . . . . . . . . . . . . 8 1080/60p recording . . . . . . . . . . . . . . . 51 3D playback/viewing . . . . . . . . . 103, 145 3D recording . . . . . . . . . . . . . . . . 79, 145 ∫A AC adaptor . . . . . . . . . . . . . . . . . 20, 144 AF assist lamp . . . . . . . . . . . . . . . . . . . 74 AF/AE tracking . . . . . . . . . . . . . . . . . . 53 Alert sound . . . . . . . . . . . . . . . . . . . . .
PAGE 163
HDCSD800P-VQT3K35_mst.book 163 ページ２０１０年１２月２０日 ∫M Manual focus . . . . . . . . . . . . . . . . . . . . 78 Manual recording . . . . . . . . . . . . . . . . . 75 Menu . . . . . . . . . . . . . . . . . . . . . . 26, 39 MF assist . . . . . . . . . . . . . . . . . . . . . . 78 Microphone level . . . . . . . . . . . . . . . . . 68 Mode switch . . . . . . . . . . . . . . . . . . . . 25 Motion picture compatibility . . . . . . . . . 38 ∫N Name display . . . . . . . . . . . . . . . . . . . 65 Number reset . . . .
PAGE 164
HDCSD800P-VQT3K35_mst.book 164 ページ２０１０年１２月２０日月曜日午前９時４分 Spanish Quick Use Guide/Guía española para el uso rápido ∫ Insertar la batería Meta la batería insertándola en la dirección señalada en la figura. ∫ Insertar/extraer una tarjeta SD   A Introduzca la batería hasta que haga clic y se cierre.  ∫ Carga de la batería Testigo de acceso [ACCESS] A ≥ Cuando el dispositivo accede a la tarjeta SD, se enciende el testigo de acceso.
PAGE 165
HDCSD800P-VQT3K35_mst.book 165 ページ２０１０年１２月２０日月曜日午前９時４分 ∫ Encender/apagar el dispositivo ∫ Selección del modo Encender y apagar el dispositivo con el botón de alimentación Pulse el botón de alimentación para encender el dispositivo. Utilizando el selector de modo, cambie el modo a , o . Modo de grabación de películas (l 30) A El indicador de estado se ilumina. ≥ Para apagar la unidad, mantenga pulsado el botón de alimentación hasta que el indicador de estado se apague.
PAGE 166
HDCSD800P-VQT3K35_mst.book 166 ページ２０１０年１２月２０日 Menú táctil Toque para visualizar el menú de deslizamiento. Toque (lado izquierdo)/ (lado derecho) de en el menú táctil para cambiar los iconos de operación. 月曜日午前９時４分 ∫ Grabación de películas 1) 2) 3) Cambie el modo a . Abra el monitor LCD. Pulse el botón de inicio/parada de grabación para iniciar la grabación. T W A Cuando comienza a grabar, ; cambia a ¥.
PAGE 167
HDCSD800P-VQT3K35_mst.book 167 ページ２０１０年１２月２０日 ∫ Reproducción de película/ fotografía 1) 2) Cambie el modo a . Toque el icono de selección del modo de reproducción A. ALL 3) Seleccione el [VIDEO/FOTO] que desea reproducir. ≥ Toque [ENTRAR]. 4) Toque la escena o la fotografía que desea reproducir.  ALL B se visualiza cuando se toca [1080/60p], se visualiza cuando se toca [AVCHD], o se visualiza cuando se toca [iFrame] en el paso 3.
PAGE 168
HDCSD800P-VQT3K35_mst.