HDC-SD40&TM40P_PC_VQT3J95_mst.book 1 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Owner’s Manual High Definition Video Camera HDC-SD40P/PC HDC-TM40P/PC HDC-TM41P/PC Model No. Before connecting, operating or adjusting this product, please read the instructions completely. For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 2 ページ Things You Should Know Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. The serial number is on the tag located on the underside of your camera. Be sure to retain this manual as your convenient camera information source.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 3 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 4 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 AC adaptor This AC adaptor operates on AC between 110 V and 240 V. But ≥ In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power supply only. ≥ When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to suit the AC outlet configuration.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 5 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. ∫ Product Identification Marking Product Location High Definition Video Camera Battery holder AC adaptor Bottom U.S.A.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 6 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 7 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Precautions USE & LOCATION WARNING ≥ TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 8 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ About the recording format for recording motion pictures ∫ Handling of built-in memory [HDC-TM40/HDC-TM41] You can select from either AVCHD or iFrame recording formats to record motion pictures using this unit. (l 54) AVCHD: You can record high definition quality images with this format. It is suitable for viewing on a large format TV or for saving to disc.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 9 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ For the purposes of this owner’s manual ≥ SD Memory Card, SDHC Memory Card and SDXC Memory Card are referred to as the “SD card”. ≥ Functions that can be used for motion picture recording/motion picture playback are indicated by in this owner’s manual. ≥ Functions that can be used for still picture recording/still picture playback are indicated by in this owner’s manual.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 10 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Contents Accessories.............................................12 Quick Guide.............................................13 Preparation Parts identification and handling .......... 17 Power supply........................................... 20 Inserting/removing the battery........... 20 Charging the battery ......................... 21 Charging and recording time............. 22 Recording to a card ................................
２０１１年１月２０日 木曜日 午前１１時４９分 Preparation HDC-SD40&TM40P_PC_VQT3J95_mst.book 11 ページ Copy/Dubbing Copying from Built-in Memory to SD card [HDC-TM40/HDC-TM41].................. 80 Dubbing with a Blu-ray disc recorder, video devices, etc................... 82 Basic With a PC Advanced (Recording) What you can do with a PC ....................86 End User License Agreement ........... 88 Operating environment .......................... 89 Installation ...............................................
HDC-SD40&TM40P_PC_VQT3J95_mst.book 12 ページ ２０１１年１月２０日 木曜日 Accessories Check the accessories before using this unit. Keep the accessories out of reach of children to prevent swallowing. Product numbers correct as of Jan. 2011. These may be subject to change.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 13 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Quick Guide ∫ Inserting the battery Install the battery by inserting it in the direction shown in the figure. ∫ Inserting/removing an SD card A Insert the battery until it clicks and locks. ∫ Charging the battery A DC input terminal 1 Connect the AC adaptor to the DC input terminal. 2 Connect the AC cable to the AC adaptor, then the AC outlet.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 14 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ Turning the unit on/off ∫ Selecting a mode Turning the unit on and off with the power button Press the power button to turn on the unit. Operate the mode switch to change the mode to or . Recording Mode (l 31) A The status indicator lights on. ≥ To turn off the unit, hold down the power button until the status indicator goes off. Turning the unit on and off with the LCD monitor Opening the LCD monitor turns on the unit.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 15 ページ ∫ Selecting a media to record [HDC-TM40/HDC-TM41] 1) 2) Change the mode to Select the menu. . ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ Recording still pictures 1) 2) 3) Change the mode to . Open the LCD monitor. Press the button to take the picture. : [MEDIA SELECT] 3) Select the media to record motion pictures or still pictures using 3/4/2/1, and press the ENTER button. ≥ Select [VIDEO/SD CARD] or [PICTURE/ SD CARD] to record to the SD card.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 16 ページ 4) Select the scene or the still picture to be played back using 3/4/2/1, then press the ENTER button. NOV 15 2011 0 h 00m15 s B is displayed when [AVCHD] is selected or is displayed when [iFrame] is selected in step 3. ≥ When you select / and press the ENTER button, the next (previous) page is displayed. 5) Select the operation icon using 3/4/2/1. 0h00m00s C Operation icon ≥ Press the ENTER button to display(/notdisplay) the operation icon.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 17 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Preparation Parts identification and handling 1 2 34 5 6 AV MULTI 7 8 10 11 9 12 14 15 13 1 2 Power button [ ] (l 26) Delete/Video light button [ /LIGHT] (l 48, 69) 3 Intelligent auto/Manual button [iA/MANUAL] (l 34, 59) 4 Optical image stabilizer button [ O.I.S.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 18 ページ 19 20 ２０１１年１月２０日 木曜日 午前１１時４９分 19 Menu button [MENU] (l 39) 20 LCD monitor (l 29) 21 22 ≥ It can open up to 90o. ≥ It can rotate up to 180o A towards the lens or 90o B towards the opposite direction. Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 19 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 23 Tripod receptacle ≥ If you attach a tripod which has a 5.5 mm (0.22 q) screw or larger, it may damage this unit.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 20 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Preparation Power supply ∫ About batteries that you can use with this unit The battery that can be used with this unit is VW-VBK180/VW-VBK360. ≥ The unit has a function for distinguishing batteries which can be used safely. The dedicated battery (VW-VBK180/VW-VBK360) supports this function.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 21 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Charging the battery When this unit is purchased, the battery is not charged. Charge the battery fully before using this unit for the first time. Important: ≥ Use the supplied AC adaptor. Do not use the AC adaptor of another device. ≥ Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do not use the AC cable from other equipment with this unit.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 22 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Charging and recording time ∫ Charging/Recording time ≥ Temperature: 25 oC (77 oF)/humidity: 60%RH (When using AC adaptor) HDC-SD40 Battery model number [Voltage/Capacity (minimum)] Charging time Recording mode Maximum continuous recordable time Actual recordable time Supplied battery/ VW-VBK180 (optional) [3.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 23 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Battery capacity indication ≥ The display changes as the battery capacity reduces. # # # # If there is less than 3 minutes remaining, then will become red. If the battery discharges, then will flash. ≥ The remaining battery capacity is displayed when using the Panasonic battery that you can use for this unit. The actual time can vary depending on your actual use.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 24 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Preparation Recording to a card The unit can record still pictures or motion pictures to an SD card or built-in memory. To record to an SD card, read the following. This unit (an SDXC compatible device) is compatible with SD Memory Cards, SDHC Memory Cards and SDXC Memory Cards. When using an SDHC memory card/SDXC memory card with other equipment, check the equipment is compatible with these memory cards.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 25 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Inserting/removing an SD card When using an SD card not from Panasonic, or one previously used on other equipment, for the first time on this unit, format the SD card. (l 44) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored. Caution: Check that the access lamp has gone off.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 26 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Preparation Turning the unit on/off You can turn the unit on and off using the power button or by opening and closing the LCD monitor. A clicking sound is heard when the unit is shaken. ≥ This is the sound of the lens moving and is not a defect. This sound will no longer be heard when the unit is turned on and change the mode to . Turning the unit on and off with the power button Press the power button to turn on the unit.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 27 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Preparation Selecting a mode Change the mode to recording or playback. Operate the mode switch to change the mode to or .
HDC-SD40&TM40P_PC_VQT3J95_mst.book 28 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Preparation Setting date and time When the unit is turned on for the first time, a message asking you to set the date and time will appear. Select [YES] and perform steps 2 to 3 below to set the date and time. ¬ Change the mode to 1 . Select the menu. (l 39) : [SETUP] # [CLOCK SET] 2 Select the date or time using 2/1 and set the desired value using 3/4.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 29 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Before recording ∫ Basic camera positioning 1 Hold the unit with both hands. 2 Put your hand through the grip belt. ≥ When recording, make sure your footing is stable and there is no danger of colliding with another person or object. ≥ When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it will become dark in the recording.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 30 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Selecting a media to record [HDC-TM40/HDC-TM41] The card and built-in memory can be selected separately to record motion pictures or still pictures. 1 2 Change the mode to . Select the menu. (l 39) : [MEDIA SELECT] 3 Select the media for recording the motion pictures and the media for recording the still pictures using 3/4/2/1, and press the ENTER button.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 31 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Recording motion pictures ≥ Open the lens cover before turning on the unit. (l 17) 1 Change the mode to and open the LCD monitor. 2 Press the recording start/ stop button to start recording. A When you begin recording, ; changes to ¥. 3 Press the recording start/ stop button again to pause recording.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 32 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ≥ There are 2 recording formats that can be used with this unit: AVCHD that records high-definition motion pictures and iFrame that records motion pictures suitable for playback and editing on Mac (iMovie’11). To change the recording format, change the recording mode. (l 54) ≥ The images recorded between pressing the recording start/stop button to start recording and pressing it again to pause recording become one scene.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 33 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Recording still pictures Still picture recorded with size of 2.1 M (1920k1080) and an aspect ratio of 16:9. ≥ Open the lens cover before turning on the unit. (l 17) 1 Change the mode to open the LCD monitor. 2 Press the and button. ∫ About the screen indications in still picture recording : 2.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 34 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Intelligent Auto Mode The following modes (appropriate for the condition) are set just by pointing the unit to what you want to record. Intelligent auto/Manual button Press this button to switch Intelligent Auto Mode/Manual Mode. ≥ Please refer to page 59 for details about Manual Mode.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 35 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ Intelligent Auto Mode When switching to Intelligent Auto Mode, the Auto White Balance and Auto Focus operate and automatically adjust the color balance and focusing. Depending on the brightness of the subject etc., the aperture and shutter speed are automatically adjusted for an optimum brightness. ≥ Color balance and focus may not be adjusted automatically depending on light sources or scenes. If so, manually adjust these settings.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 36 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Motion picture/Still picture playback 1 2 Change the mode to . Select the play mode select icon A using 3/4/2 and press the ENTER button. 3 Select the [VIDEO/PICTURE] you wish to play back, then press the ENTER button. / Select the [MEDIA] and [VIDEO/PICTURE] you wish to play back, then press the ENTER button. / ≥ Press the MENU button.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 37 ページ 5 ２０１１年１月２０日 木曜日 午前１１時４９分 0h00m00s Select the operation icon using 3/4/2/1. A Operation icon ≥ Press the ENTER button to display (/not-display) the operation icon. Motion picture playback 1/;: 6: 5: ∫: Playback/Pause Rewind playback Fast forward playback Stops the playback and shows the thumbnails. Still picture playback 1/;: 2;: ;1: ∫: Slide show (playback of the still pictures in numerical order) start/pause. Plays back the previous picture.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 38 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Motion picture compatibility ≥ This unit is based on AVCHD format/MPEG-4 AVC file format. ≥ Video signal for the AVCHD that can be played back with this unit is 1920k1080/60i. ≥ Video signal for the iFrame that can be played back with this unit is 960k540/30p. ≥ Motion pictures recorded using other equipment cannot be played back on this unit. ≥ Motion pictures recorded in AVCHD and iFrame are not compatible with each other.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 39 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Using the menu screen 1 2 To get back to the previous screen Press the MENU button. Press 2 of the cursor button. Select the top menu A using 3/4 and press 1 or press the ENTER button. To exit the menu screen Press the MENU button. ∫ About the information display Descriptions of the selected submenus and items displayed in steps 3 and 4, and messages to confirm settings are displayed.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 40 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Basic Using the Setup Menu ≥ The items displayed differ depending on the position or settings of the mode switch. Select the menu. : [SETUP] # desired setting [DISPLAY] [OFF]/[ON] The screen display can be changed to [OFF] (a portion of information displayed) or [ON] (all information displayed). [CLOCK SET] Please refer to page 28.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 41 ページ 5 ２０１１年１月２０日 木曜日 午前１１時４９分 (Only when setting the region of your travel destination) Select your travel destination using 2/1 and press the ENTER button. ≥ Press 3 to set daylight saving time. appears and the summer C The local time at the selected travel time setting is turned on.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 42 ページ [QUICK START] ２０１１年１月２０日 木曜日 午前１１時４９分 [OFF]/[ON] This unit is put into recording pause approx. 0.6 seconds after the LCD monitor is reopened. ≥ When in Quick start standby mode about 60% of the power used in Recording pause mode is being consumed, so the recording time will be reduced. ≥ Quick start will not work if there is no SD card inserted.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 43 ページ [POWER LCD] +2 ２０１１年１月２０日 木曜日 午前１１時４９分 / +1 / 0 / -1 This makes it easier to view the LCD monitor in bright places including outdoors. ≥ These settings will not affect the images actually recorded. +2 (Makes even brighter)/ +1 (Makes brighter)/ 0 (Normal)/ -1 (Reduces brightness) ≥ When the AC adaptor is in use, the LCD monitor is set to +1 automatically. ≥ When the LCD monitor is bright, the recordable time with the battery will be shorter.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 44 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 [INITIAL SET] Set to [YES] for changing the menu settings back to the default condition. (Only when the mode is at the position) ≥ Settings for [MEDIA SELECT]*, [CLOCK SET] and [LANGUAGE] will not be changed. * For users who have , this menu is not displayed. [FORMAT CARD] Please be aware that if a medium is formatted, then all the data recorded on the medium will be erased and cannot be restored.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 45 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 [CARD STATUS] The used space and remaining recordable time of the SD card can be checked. ≥ When the mode switch is set to , remaining recordable time for the selected recording mode is displayed. ≥ Press the MENU button to close the indication. ≥ The SD card requires some space to store information and manage system files, so the actual usable space is slightly less than the indicated value.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 46 ページ [DEMO MODE] ２０１１年１月２０日 木曜日 午前１１時４９分 [OFF]/[ON] This item is used to start the unit demonstration. (Only when the mode is at the position) If [DEMO MODE] is switched to [ON] and you press the MENU button when there is no SD card inserted and while this unit is connected to the AC adaptor, the demonstration automatically starts. If any operation takes place, the demonstration is canceled. However if no operations take place for approx.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 47 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Recording) Zoom in/out function ¬ Change the mode to . Zoom lever T 6 W T side: Close-up recording (zoom in) W side: Wide-angle recording (zoom out) ≥ The zoom speed varies depending on the range over which the zoom lever is moved. ≥ Maximum zoom magnification can be set with [D.ZOOM]. (l 54) ≥ If you take your finger off the zoom lever during zoom operation, the operation sound may be recorded.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 48 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Recording) Optical image stabilizer function Optical image stabilizer can stabilize the image without decreasing the image quality as much. ¬ Change the mode to . Optical image stabilizer button Press the button to turn optical image stabilizer on/off. (On) # setting canceled ≥ When you wish to record as you walk, we recommend that turn the optical image stabilizer on.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 49 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Recording) Recording functions of operation icons Select the operation icons to add different effects to the images to be recorded. ¬ Change the mode to 1 . Press the ENTER button to display the operation icons on the screen. 2 (e.g. Backlight compensation) Select an operation icon. 1/2 ワユヹヵ 1/2 ワユヹヵ ≥ The indication changes each time you press 4 of the cursor button.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 50 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Fade When you start recording, the image/audio gradually appears. (Fade in) When you pause recording, the image/audio gradually disappears. (Fade out) ≥ The Fade setting is canceled when the recording stops. (Fade in) ∫ To select the color for Fade in/out (Fade out) : [RECORD SETUP] # [FADE COLOR] # [WHITE] or [BLACK] ≥ The thumbnails of scenes recorded using fade in become black (or white).
HDC-SD40&TM40P_PC_VQT3J95_mst.book 51 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Tele macro A more impressive image can be obtained by focusing on the object only in close-up and shading off the background. ≥ The unit can focus on the subject at a distance of approx. 50 cm (20q). ≥ If you set the tele macro function when the zoom is set to less than 16.8k, the zoom is automatically adjusted to 16.8k. ≥ Tele Macro function is canceled when the zoom magnification becomes lower than 16.8k.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 52 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Intelligent contrast control This brightens parts that are in shadow and difficult to see and suppresses white saturation in bright parts at the same time. Both bright and dark parts can be recorded clearly. ≥ If there are extremely dark or bright parts or the brightness is insufficient, the effect may not be clear. Color Night Rec This function allows you to record color images in very low light situations.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 53 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Recording) Recording functions of menus ≥ Change the mode to . [SCENE MODE] When you record images in different situations, this mode automatically sets optimum shutter speeds and apertures.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 54 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 [D.ZOOM] Set the maximum zoom ratio. : [RECORD SETUP] # [D.ZOOM] # desired setting [OFF]: Optical zoom only (Up to 16.8k) [50k]: Digital zoom (Up to 50k) / [1200k]: Digital zoom (Up to 1200k) [1500k]: Digital zoom (Up to 1500k) ≥ The larger the digital zoom magnification, the more the image quality is degraded. [REC MODE] Switch the picture quality and recording format of the motion pictures to be recorded.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 55 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 [FACE FRAMING] Detected faces appear with frames. : [RECORD SETUP] # [FACE FRAMING] # desired setting [OFF]: Cancel the setting. [PRIMARY]: Only the prioritized face framing is displayed. [ALL]: All face detection framings are displayed. ≥ Up to 15 frames are indicated. Larger faces and faces nearer to the center of the screen take preference over others. ∫ Prioritized face framing Prioritized face framing is displayed as orange frames.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 56 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 [AUTO SLOW SHTR] You can record bright pictures even in dark places by slowing the shutter speed. ≥ Switch to Manual Mode. (l 59) : [RECORD SETUP] # [AUTO SLOW SHTR] # [ON] ≥ The shutter speed is set to 1/30 or more depending on the surrounding brightness. ≥ When the shutter speed becomes 1/30, the screen may be seen as if frames are missed and afterimages may appear.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 57 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 [MIC LEVEL] When recording, the input level from the built-in microphones can be adjusted. ≥ Switch to Manual Mode. (l 59) 1 Select the menu. : [RECORD SETUP] # [MIC LEVEL] # desired setting [AUTO]: [SETr AGC is activated, and the recording level is adjusted automatically. ]: [SET]: 2 The desired recording level can be set. AGC is activated, reducing noise. The desired recording level can be set.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 58 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 [SELF TIMER] This is for recording still pictures using the timer. : [PICTURE] # [SELF TIMER] # desired setting [OFF]: Cancel the setting. [10 SECONDS]: Records after 10 seconds [2 SECONDS]: Records after 2 seconds ≥ When the button is pressed, a still picture is recorded after the Ø10 or Ø2 display flashes for the time which has been set. After recording, the self-timer is canceled.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 59 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Recording) Manual recording ¬ Change the mode to . Press the iA/MANUAL button to switch to Manual Mode. ≥ MNL appears on the screen. 4/5 NEXT 5/5 NEXT White balance Manual shutter speed (l 61) Iris adjustment (l 61) Focus (l 62) ≥ Press the ENTER button to display/not-display the manual icon. ≥ The page changes with each press of 4.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 60 ページ Icon AWB ２０１１年１月２０日 木曜日 午前１１時４９分 Mode/Recording conditions Auto white balance adjustment Sunny mode: Outdoors under a clear sky Cloudy mode: Outdoors under cloudy sky Indoor mode 1: Incandescent light, video lights like in the studio, etc. Indoor mode 2: Color fluorescent lamps, sodium lamps in gymnasiums etc.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 61 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Manual shutter speed/iris adjustment Shutter Speed: Adjust it when recording fast-moving subjects. Iris: Adjust it when the screen is too bright or too dark. ≥ Press the iA/MANUAL button to switch to Manual Mode. (l 59) 1 2 Select [SHTR] or [IRIS] using the cursor button. Press 2/1 to adjust settings. A : Shutter speed: 1/60 to 1/8000 ≥ If [AUTO SLOW SHTR] is set to [ON], the shutter speed will be set between 1/30 and 1/8000.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 62 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Recording with Manual focus If auto focusing is difficult due to the conditions, then use Manual Focus. ≥ Press the iA/MANUAL button to switch to Manual Mode. (l 59) 1 2 Press 4 to switch the manual icon. Select [MF] using the cursor button to change to manual focus. ≥ MF appears on the screen. 3 Press 2/1 to adjust the focus.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 63 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Playback) Playback Operations Motion picture playback using operation icon For details on the basic playback operations, refer to page 36. Playback operation Cursor button/ Playback display During Playback Fast forward/ rewind playback Slow-motion playback During Pause Frame-by-frame playback The motion picture is advanced one frame at a time. Operating steps Press 1 of the cursor button during playback to fast forward.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 64 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Creating still picture from motion picture A single frame from the recorded motion picture can be saved as a still picture. Picture size of the still picture to be created will differ depending on the recording mode of the recorded motion picture. Recording mode Aspect ratio [HA]/[HG]/[HX] Picture size after creating still picture 2.1 M 1920k1080 0.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 65 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Resuming the previous playback If playback of a scene was stopped halfway, the playback can be resumed from where it was stopped. : [VIDEO SETUP] # [RESUME PLAY] # [ON] If playback of a motion picture is stopped, scene. appears on the thumbnail view of the stopped ≥ The memorized resume position is cleared if you turn off the unit or change the mode. (The setting of [RESUME PLAY] does not change.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 66 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Playback) Various playback functions Playing back motion pictures/still pictures by date The scenes or the still pictures recorded on the same day can be played back in succession. 1 Select the date select icon using the cursor button, then press the ENTER button. A Date select icon 2 Select the playback date, then press the ENTER button.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 67 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Changing the playback settings and playing back the slide show 1 Select using the cursor button, then press the ENTER button. 2 Select the desired item and press the ENTER button. [DATE SETUP]: Select the date to be played back. [SLIDE INTERVAL]: Selects the interval between still pictures at playback. [MUSIC SELECT]: Select the music to be played on playback.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 68 ページ 4 5 ２０１１年１月２０日 木曜日 午前１１時４９分 Select [START] and press the ENTER button. Select the playback operation. (l 36) ≥ When the playback is finished or stopped, the screen to select [REPLAY], [SELECT AGAIN] or [EXIT] is displayed. Select the desired item and press the ENTER button. ≥ To adjust the volume of music during playback of the slide show, operate the volume lever.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 69 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Playback) Deleting scenes/still pictures Deleted scenes/still pictures cannot be restored, so perform appropriate confirmation of the contents before proceeding with deletion. ¬ Change the mode to . To delete by confirming images being played back Press the /LIGHT button while scenes or still pictures to be deleted are being played back.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 70 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 To complete editing Press the MENU button. ≥ You can also delete scenes by pressing the MENU button, selecting [EDIT SCENE] # [DELETE] # [ALL SCENES] or [SELECT]. ≥ You can also delete still pictures by pressing the MENU button, selecting [PICT. SETUP] # [DELETE] # [ALL SCENES] or [SELECT]. ≥ Scenes which cannot be played back (the thumbnails are displayed as ) cannot be deleted.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 71 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Dividing a scene (AVCHD) It is possible to divide an AVCHD scene. Any unwanted parts in the scene can be deleted after dividing. ≥ Change the mode to , and set [VIDEO/PICTURE] of the play mode selection to [AVCHD]. (l 36) 1 Select the menu. : [EDIT SCENE] # [DIVIDE] # [SET] 2 Select the scene you wish to divide using the cursor button and press the ENTER button. 3 Select to set the dividing point.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 72 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Dividing a scene to partially delete (iFrame) Divide the iFrame scene, and delete unnecessary parts. This divides the recorded scenes in two and deletes the front half or back half. The scenes that were deleted after division cannot be recovered. ≥ Change the mode to , and set [VIDEO/PICTURE] of the play mode selection to [iFrame]. (l 36) 1 Select the menu.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 73 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Protecting scenes/still pictures Scenes/still pictures can be protected so that they are not deleted by mistake. (Even if you protect some scenes/still pictures, formatting the media will delete them.) ≥ Change the mode to . 1 Select the menu. : [VIDEO SETUP] or [PICT. SETUP] # [SCENE PROTECT] 2 Select the scene/still picture to be protected using the cursor button, then press the ENTER button.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 74 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Playback) Watching Video/Pictures on your TV Confirm the terminals on your TV and use a cable compatible with the terminals. Image quality may vary with the connected terminals. A High quality 1 HDMI terminal 2 Component terminal 3 Video terminal ≥ Use the AV multi cable (supplied) or HDMI mini cable (optional) and check the output settings. (l 77) ≥ HDMI is the interface for digital devices.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 75 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ≥ Check that the plugs are inserted as far as they go. ≥ Always use a genuine Panasonic HDMI mini cable (RP-CDHM15, RP-CDHM30; optional). ≥ Do not use any other AV multi cables except the supplied one. ≥ When connecting to the component terminal of the TV, the yellow plug of the AV multi cable is not required. ≥ When connecting to the AV terminal of the TV, do not connect the component terminal plug of the AV multi cable.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 76 ページ ∫ To watch images on a regular TV (4:3) or when both sides of the images do not appear on the screen Change the menu setting to display the images correctly. (Check the TV setting.) ２０１１年１月２０日 木曜日 午前１１時４９分 Example of images with a [16:9] aspect ratio on a regular TV (4:3) [TV ASPECT] setting [16:9] [4:3] : [SETUP] # [TV ASPECT] # [4:3] ≥ If a wide-screen TV is connected, adjust the aspect setting on the TV.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 77 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Connecting with a HDMI mini cable Select the desired method of HDMI output. : [SETUP] # [HDMI RESOLUTION] # [AUTO]/[1080i]/[480p] ≥ [AUTO] determines the output resolution automatically based on information from the connected TV. If the images are not output on the TV when the setting is [AUTO], switch to the method [1080i] or [480p] which enables the images to be displayed on your TV. (Please read the operating instructions for the TV.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 78 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Advanced (Playback) Playback using VIERA Link™ What is the VIERA Link (HDAVI Control™)? ≥ VIERA Link™ is a new name for EZ Sync™. ≥ This function allows you to use your remote control for the Panasonic TV for easy operations when this unit has been connected to a VIERA Link compatible device using a HDMI mini cable (optional) for automatic linked operations. (Not all operations are possible.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 79 ページ 3 ２０１１年１月２０日 木曜日 午前１１時４９分 Operate with the remote control for the TV. 2) 1) NOV 15 2011 0 h 00m15 s 1) Press the button up, down, left or right to select a scene or still picture to be played back, and then press the button in the center to set it. 2) Activate the operation icons that are displayed on TV screen with the remote control for the TV.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 80 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Copy/Dubbing Copying from Built-in Memory to SD card [HDC-TM40/HDC-TM41] Motion pictures or still pictures recorded with this unit can be copied from a built-in memory to an SD card inserted in this unit. ∫ Check the used space of the SD card It is possible to check the used space of the SD card by [MEDIA STATUS] (l 45). ≥ Depending on the media condition, some remaining capacity of the SD card may not be used.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 81 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 When you stop copying halfway Press the MENU button while copying. If you will delete the motion pictures or still pictures after copying is complete, be sure to play back the motion pictures or still pictures to check that they have been copied to correctly before deleting. ≥ Depending on the following conditions, the time it takes for copying may be longer. j The number of recorded scenes is large.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 82 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Copy/Dubbing Dubbing with a Blu-ray disc recorder, video devices, etc. ∫ Check before dubbing Check the equipment used for dubbing.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 83 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Dubbing in high-definition picture quality You can dub using a Panasonic Blu-ray disc recorder or high-definition (AVCHD) compatible DVD recorder. ≥ Depending on the recorders or the media to be copied to, you may not be able to copy in high-definition (AVCHD) picture quality. For further details, see the operating instructions of your recorder. ≥ Note that the equipment described may not be available in certain countries and regions.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 84 ページ 2 ２０１１年１月２０日 木曜日 午前１１時４９分 Select [RECORDER] using the cursor button on the unit and press the ENTER button. ≥ When you select an option other than [RECORDER], reconnect the USB cable. ≥ When using the battery, the LCD monitor turns off after about 5 seconds. Press the cursor button to turn the LCD monitor on. 3 / Select the media you wish to dub, then press the ENTER button. ≥ When using the battery, the LCD monitor turns off after about 5 seconds.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 85 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Dubbing in standard picture quality ∫ Dubbing using equipment without an SD card slot or a USB terminal, or using a video device You can dub by connecting an AV multi cable. ≥ Images are dubbed in standard quality. ≥ Use the AC adaptor to free you from worrying about the battery running down. Change the video input on the video device and TV that this unit is connected to.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 86 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 With a PC What you can do with a PC HD Writer LE 1.0 You can copy the motion/still picture data to the HDD of PCs or write to media like Blu-ray discs, DVD discs or SD cards using HD Writer LE 1.0, the software installed in the supplied CD-ROM. Refer to the operating instructions of HD Writer LE 1.0 (PDF file) for details on how to use it.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 87 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ≥ It is possible to play back on a PC using a image viewer standard to Windows or commercially available image browsing software, and copy pictures to a PC using Windows Explorer. ≥ Please refer to page 98 for details about using a Mac. Important Notice ≥ When using an SDXC Memory Card, check the following support site. http://panasonic.net/avc/sdcard/information/SDXC.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 88 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 End User License Agreement Before opening the CD-ROM package, please read the following. You (“Licensee”) are granted a license for the Software defined in this End User License Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 89 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 With a PC Operating environment ≥ Even if the system requirements mentioned in this owner’s manual are fulfilled, some PCs cannot be used. ≥ A CD-ROM drive is necessary to install the supplied software applications. (A compatible Blu-ray disc/DVD writer drive and media are necessary for writing to a Blu-ray disc/DVD.) ≥ Operation is not guaranteed in the following cases.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 90 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Free hard disk drive space Ultra DMA — 100 or more 450 MB or more (for installing the software) ≥ When writing to a DVD/Blu-ray disc/SD, more than double the amount of free space as the disc being created is necessary. Sound DirectSound Support Interface USB port [Hi-Speed USB (USB 2.0)] Other requirements Mouse or equivalent pointing device Internet connection ≥ Supplied CD-ROM is available for Windows only.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 91 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ Operating environment for the card reader function (mass storage) PC IBM PC/AT compatible PC OS Windows 7 (32 bit/64 bit) Windows Vista (32 bit) (SP1/SP2) Windows XP (32 bit) (SP3) CPU Windows 7/Windows Vista: 1.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 92 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 With a PC Installation When installing the software, log on to your computer as the Administrator or with a user name with equivalent authorization. (If you do not have authorization to do this, consult your manager.) ≥ Before starting the installation, close all applications that are running. ≥ Do not perform any other operations on your PC while the software is being installed.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 93 ページ 7 ２０１１年１月２０日 木曜日 午前１１時４９分 When installation is complete, some notes will appear. Check the contents, then close the window. 8 Select [Yes, I want to restart my computer now.], then click [Finish]. The PC must be rebooted for the application to work. ∫ Uninstalling HD Writer LE 1.0 Follow the steps below to uninstall any software applications that you no longer require. 1 Select [Start] # [Control Panel] # [Uninstall a program].
HDC-SD40&TM40P_PC_VQT3J95_mst.book 94 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 With a PC Connecting to a PC ≥ Connect this unit to the PC after the software applications are installed. ≥ Remove the supplied CD-ROM from your PC. A USB cable (supplied) ≥ Insert the plugs as far as they will go. 1 Connect this unit to the AC adaptor. ≥ It is possible to use it connected to the PC with the batteries only, but you will not be able to write data into the unit.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 95 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ To disconnect USB cable safely Select the icon in task tray displayed on the PC, and then click [Eject Panasonic Camcorder]. ≥ Depending on your PC’s settings, this icon may not be displayed. About the screen indication of the unit ≥ Do not disconnect the USB cable, the battery or the AC adaptor while the access lamp is on or card access icon ( ) appears on the unit screen.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 96 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 About the PC display When the unit is connected to a PC, it is recognized as an external drive. ≥ Removable disk (Example: ) is displayed in [Computer]. We recommend using HD Writer LE 1.0 to copy or write back motion picture data. Using Windows Explorer or other programs on the PC to copy, move or rename files and folders recorded with this unit will result in them being unusable with HD Writer LE 1.0.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 97 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 With a PC Starting HD Writer LE 1.0 ≥ To use the software, log on as an Administrator or as user name for standard user account (only for Windows 7/Windows Vista). The software cannot be used with the user name for a guest account. (On the PC) Select [Start] # [All Programs] # [Panasonic] # [HD Writer LE 1.0] # [HD Writer LE]. ≥ For details on how to use the software applications, read the PDF operating instructions of the software.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 98 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 With a PC If using Mac ≥ HD Writer LE 1.0 is not available for Mac. ≥ iMovie’11 supported. For details about iMovie’11, please contact Apple Inc. ≥ There are some limitations in the functions when iMovie’11 is used. Refer to page 106 for details. ∫ Operating environment PC Mac OS Mac OS X 10.6.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 99 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Indications * / only (White) Card recording possible status (motion picture) (Green) Recognizing the card (motion picture) ∫ Recording indications 0h00m00s +1 1h30m R 1h20m MF / PRE-REC / R 1h20m Remaining time for motion picture recording (l 31) R 3000 2.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 100 ページ C Built-in memory recording possible status (still picture)* (White) Card recording possible status (still picture) (Green) Recognizing the card (still picture) / ２０１１年１月２０日 Number of recording pixels for still pictures (l 33, 64) 1/;/5/6/7/8/D/E/;1/2; Display during playback (l 36, 63) 0h00m00s Playback Time (l 36) No.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 101 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Messages Major confirmation/error messages to be indicated on the screen in text. * / only PERIODICALLY MAKE BACK UP OF DATA IN BUILT-IN MEMORY.* We recommend backing up important recorded motion pictures and still pictures periodically to a PC, DVD disc etc. to protect it. (l 86) This message does not indicate that there is a problem with this unit. CHECK CARD. This card is not compatible or it cannot be recognized by the unit.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 102 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 About recovery If faulty management information is found, the messages may appear and a repair is performed. (Repairing may take time depending on the error.) SOME SCENES NEED REPAIRING. PLAY SCENES TO BE REPAIRED. (IRREPARABLE SCENES WILL BE DELETED.) ≥ The above message is displayed when abnormal management information is detected when the scenes are displayed in thumbnail.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 103 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Troubleshooting Power Problem This unit cannot be turned on. This unit does not stay on long enough. Battery runs down quickly. Check points ≥ Charge the battery again to ensure it is sufficiently charged. (l 21) ≥ In cold places, the battery using time becomes shorter. ≥ The battery has a limited life.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 104 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Recording Problem Check points The unit arbitrarily stops recording. ≥ Use an SD card that can be used for motion picture recording. (l 24) ≥ The recordable time may have shortened due to the deterioration of the data writing speed or repeated recording and deletion. Using the unit, format the SD card or built-in memory. (l 44) ≥ If [AGS] is [ON], record in the normal horizontal position or set [AGS] to [OFF].
HDC-SD40&TM40P_PC_VQT3J95_mst.book 105 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Playback Problem Scenes cannot be deleted. Check points ≥ Release the protect setting. (l 73) ≥ Any scenes/still pictures where the thumbnails are displayed as cannot be deleted. If the scenes/still pictures are unnecessary, format the media to erase the data. (l 44) Please be aware that if a media is formatted then all the data recorded on the media is erased and cannot be recovered. Back up important data on a PC, disc etc.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 106 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 With other products Problem Check points Cannot copy scenes on the SD card by connecting to other equipment with the USB cable. ≥ Other equipment might have not recognized the SD card. Unplug the USB cable once, and reconnect it. With a PC Problem Check points When connected by the USB cable, this unit is not detected by the PC. ≥ After re-inserting the SD card into the unit, reconnect the supplied USB cable.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 107 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ If AVCHD scenes do not change smoothly when played back on another device The images may be still for several seconds at the joins between the scenes if the following operations are performed when multiple scenes have been continuously played back using another unit. ≥ Just how smoothly the scenes will be played back depends on the playback unit.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 108 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Cautions for use About this unit The unit and the SD card become warm during use. This is not a malfunction. Keep this unit as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). ≥ If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be disrupted by electromagnetic wave radiation.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 109 ページ Do not use the unit for surveillance purposes or other business uses. ≥ This unit was designed for consumer intermittent use. It was not intended for continuous use, or for any industrial or commercial application resulting in prolonged use. ≥ In certain situations, continuous use could cause the unit to overheat and cause a malfunction. Such use is strongly discouraged.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 110 ページ ≥ Extremely high temperatures or low temperatures will shorten the life of the battery. ≥ If the battery is kept in high-temperature, high-humidity, or oily-smoky places, the terminals may rust and cause malfunctions. ≥ To store the battery for a long period of time, we recommend you charge it once every year and store it again after you have completely used up the charged capacity. ≥ Dust and other matter attached to the battery terminals should be removed.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 111 ページ About status indicator during charging When the status indicator is flashing at a particularly fast or slow rate, the following should be considered. Flashing with approx. 4 second period (off for approx. 2 seconds, on for approx. 2 seconds): ≥ When the battery is over discharged or the temperature of the battery is too high or low. It can be charged, but it may take a few hours to complete the charging normally.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 112 ページ LCD monitor ≥ When the LCD monitor gets dirty, wipe it with a soft cloth such as eye glass cleaner. ≥ In a place with drastic temperature changes, condensation may form on the LCD monitor. Wipe it with a soft cloth such as eye glass cleaner. ≥ When the unit has become very cold, for example due to storage in a cold area, its LCD monitor will be slightly darker than usual immediately after the unit is turned on.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 113 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others About copyright ∫ Carefully observe copyright laws Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights. ∫ Licenses ≥ SDXC Logo is a trademark of SD-3C, LLC. ≥ “AVCHD” and the “AVCHD” Logo are trademarks of Panasonic Corporation and Sony Corporation.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 114 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Recording modes/approximate recordable time ≥ SD cards are only mentioned with their main memory size. The stated times are the approximate recordable times for continuous recording.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 115 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Approximate number of recordable pictures ≥ SD cards are only mentioned with their main memory size. The stated number is the approximate number of recordable pictures. (When [QUALITY] is set to ) Picture size 2.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 116 ページ ２０１１年１月２０日 Others Specifications High Definition Video Camera Information for your safety Power source: Power consumption: DC 5.0 V (When using AC adaptor) DC 3.6 V (When using battery) Recording: 3.5 W Charging: 7.7 W Signal system: 1080/60i, 540/30p Recording format: [HA]/[HG]/[HX]: AVCHD format compliant [iFrame]: MPEG-4 AVC file format compliant (.MP4) Image sensor: 1/5.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 117 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Speaker: 1 round speaker, dynamic type White balance adjustment: Auto tracking white balance system Standard illumination: 1,400 lx Minimum required illumination: Approx. 7 lx (1/30 with Low light mode in the Scene mode) Approx. 1 lx with the Color Night Rec function AV multi connector video output level: Component video output level: Y: 1.0 Vp-p, 75 h Pb: 0.7 Vp-p, 75 h Pr: 0.7 Vp-p, 75 h AV video output level: 1.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 118 ページ ２０１１年１月２０日 Operating humidity: 10%RH to 80%RH Battery operation time: See page 22 ∫ Motion pictures Recording media: SD Memory Card (FAT12 and FAT16 system compliant) SDHC Memory Card (FAT32 system compliant) SDXC Memory Card (exFAT system compliant) Refer to page 24 for details on SD cards usable in this unit. / Built-in memory: 16 GB Compression: MPEG-4 AVC/H.264 Recording mode and transfer rate: [HA]: Approx. 17 Mbps (VBR) [HG]: Approx.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 119 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 AC adaptor Information for your safety Power source: Power consumption: DC output: AC 110 V to 240 V, 50/60 Hz 12 W DC 5.0 V, 1.6 A Dimensions: 46 mm (W)k25 mm (H)k75.5 mm (D) [1.8 q (W)k1.0 q (H)k3.0 q (D)] Mass (Weight): Approx. 115 g (Approx. 0.25 lbs.) Specifications may change without prior notice.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 120 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Optional accessories Accessory No.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 121 ページ Accessory No.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 122 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Accessory Order Form (For USA and Puerto Rico Customers) Please photocopy this form when placing an order. 1. Model # 2. Items Ordered Accessory # Description Price Each Quantity Total Price Subtotal Your State & Local Sales Tax Shipping & Handling 6.95 Total Enclosed 3. Method of payment (check one) Check of Money Order enclosed (NO C.O.D.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 123 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Limited Warranty (ONLY FOR U.S.A.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 124 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 125 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Others Warranty (For Canadian Customers) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 126 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Index ∫A Guideline . . . . . . . . . . . . . . . . . . . . . . .50 AC adaptor . . . . . . . . . . . . . . . . . 21, 110 Alert sound . . . . . . . . . . . . . . . . . . . . . 42 Approximate number of recordable pictures . . . . . . . . . . . . . . . . . . . . . . . 115 Auto focus . . . . . . . . . . . . . . . . . . . . . . 35 Auto Ground-Directional Standby (AGS) . . . . . . . . . . . . . . . . . . . . . . . . . 55 Auto slow shutter . .
HDC-SD40&TM40P_PC_VQT3J95_mst.book 127 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Repeat playback . . . . . . . . . . . . . . . . . 64 Resume playback . . . . . . . . . . . . . . . . 65 ∫S Scene mode . . . . . . . . . . . . . . . . . . . . 53 Scene protect . . . . . . . . . . . . . . . . . . . 73 SD Memory Card . . . . . . . . . . . . . . . . . 24 SD Speed Class Rating . . . . . . . . . . . . 24 SDHC Memory Card . . . . . . . . . . . . . . 24 SDXC Memory Card . . . . . . . . . . . . . . 24 Self-recording . . . . . .
HDC-SD40&TM40P_PC_VQT3J95_mst.book 128 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Spanish Quick Use Guide/Guía española para el uso rápido ∫ Insertar la batería Meta la batería insertándola en la dirección señalada en la figura. ∫ Insertar/extraer una tarjeta SD A Introduzca la batería hasta que haga clic y se cierre. ∫ Carga de la batería A Terminal de entrada de CC 1 Conecte el adaptador de CA al terminal de entrada de CC. 2 Conecte el cable de CA al adaptador de CA, luego a la toma de CA.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 129 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ Encender/apagar el dispositivo ∫ Selección del modo Encender y apagar el dispositivo con el botón de alimentación Pulse el botón de alimentación para encender el dispositivo. Utilizando el selector de modo, cambie el modo a o . Modo de grabación (l 31) A El indicador de estado se ilumina. ≥ Para apagar la unidad, mantenga pulsado el botón de alimentación hasta que el indicador de estado se apague.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 130 ページ ∫ Seleccionar un medio para grabar [HDC-TM40/HDC-TM41] 1) 2) Cambie el modo a Seleccione el menú. . ２０１１年１月２０日 木曜日 午前１１時４９分 ∫ Grabación de películas 1) 2) 3) Cambie el modo a . Abra el monitor LCD. Para tomar una imagen pulse el botón a tope. : [SELEC MEDIO] 3) Seleccione el medio para grabar las películas o fotografías usando 3/4/2/1 y pulse el botón ENTER. ≥ Seleccione [VÍDEO/TARJETA SD] o [IMAGEN/TARJETA SD] para grabar en la tarjeta SD.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 131 ページ 4) Seleccione la escena o la fotografía que desea reproducir usando 3/4/2/1, y pulse el botón ENTER. NOV 15 2011 0 h 00m15 s B se visualiza cuando se toca [AVCHD] o se visualiza cuando se toca [iFrame] en el paso 3. ≥ Cuando selecciona / y pulsa el botón ENTER, se visualiza la página siguiente (anterior). 5) Seleccione la icono de funcionamiento usando 3/4/2/1.
HDC-SD40&TM40P_PC_VQT3J95_mst.book 132 ページ ２０１１年１月２０日 木曜日 午前１１時４９分 Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Panasonic Canada Inc.
