Operating Instructions

ManualsBrandsPanasonic ManualsAV ProductsHCX1GC

Table Of Contents

4K Video Camera

Model No. HC-X1

Please read these instructions carefully before using this product, and save this manual for future use.

DVQP1176ZA

until

2016/10/28

HC-X1_E_GC_DVQP1176ZA_eng.book 1 ページ２０１６年１１月２８日　月曜日　午前１１時４０分

Summary of content (232 pages)

PAGE 1
HC-X1_E_GC_DVQP1176ZA_eng.book 1 ページ２０１６年１１月２８日月曜日午前１１時４０分 Operating Instructions 4K Video Camera Model No. HC-X1 Please read these instructions carefully before using this product, and save this manual for future use.
PAGE 2
HC-X1_E_GC_DVQP1176ZA_eng.book 2 ページ２０１６年１１月２８日月曜日午前１１時４０分 Information for Your Safety Before use For the AC mains plug of three pins ∫ Caution for AC mains lead Remove the connector cover. For your safety, please read the following text carefully. How to replace the fuse This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug.
PAGE 3
HC-X1_E_GC_DVQP1176ZA_eng.book 3 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Concerning the battery Warning Risk of fire, explosion and burns. Do not disassemble, heat above 60 oC or incinerate. CAUTION ≥ Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer. ≥ When disposing of the batteries, please contact your local authorities or dealer and ask for the correct method of disposal.
PAGE 4
HC-X1_E_GC_DVQP1176ZA_eng.book 4 ページ２０１６年１１月２８日 Note regarding the Power Management function specified under COMMISSION REGULATION (EC) No 1275/2008 implementing Directive 2009/125/EC of the European Parliament and of the Council. This device is designed and manufactured for use at a broadcasting station and/or in a similar environment.
PAGE 5
HC-X1_E_GC_DVQP1176ZA_eng.book 5 ページ２０１６年１１月２８日 When carrying the unit, do not drop or bump it. ≥ A strong impact can break the unit’s casing, causing it to malfunction. ≥ When carrying this unit, please hold the handle, hand strap or shoulder strap firmly and treat it with care. Cleaning ≥ Before cleaning, detach the battery or pull the AC cable from the AC outlet, and then wipe the unit with a soft, dry cloth.
PAGE 6
HC-X1_E_GC_DVQP1176ZA_eng.book 6 ページ２０１６年１１月２８日 Do not throw old battery into fire. ≥ Heating a battery or throwing it into a fire may result in an explosion. If the operating time is very short even after the battery has been recharged, the battery has worn out. Please purchase a new battery. About the AC adaptor/battery charger ≥ If the temperature of the battery is extremely high or extremely low, charging may take time or the battery may not be charged.
PAGE 7
HC-X1_E_GC_DVQP1176ZA_eng.book 7 ページ２０１６年１１月２８日月曜日午前１１時４０分 LCD monitor/viewfinder About personal information ≥ When the LCD screen is dirty or condensation has occurred, please wipe it using a soft cloth such as a lens cloth. ≥ Do not touch the LCD monitor with your finger nails, or rub or press with strong force. ≥ It may become hard to see or hard to recognize the touch when the LCD protection sheet is affixed.
PAGE 8
HC-X1_E_GC_DVQP1176ZA_eng.book 8 ページ２０１６年１１月２８日 ≥ Those methods can record motion pictures in formats that support 4K. 4K motion pictures offer a resolution four times higher than that of full high-definition motion pictures. AVCHD: This recording method is suitable for playback on a high-definition compatible external monitor. Audio is recorded in Dolby® Digital.
PAGE 9
HC-X1_E_GC_DVQP1176ZA_eng.book 9 ページ２０１６年１１月２８日月曜日午前１１時４０分 Contents Information for Your Safety ......................... 2 Accessories ................................................. 11 Optional accessories .................................. 12 Preparation What you can do with this unit .................. 13 Recording to the SD card ...................... 13 Linking to external devices .................... 13 Remote operations with an iPad ............ 15 Names and Functions of Main Parts ......
PAGE 10
HC-X1_E_GC_DVQP1176ZA_eng.book 10 ページ２０１６年１１月２８日月曜日午前１１時４０分 Linking to external devices Display Connecting Headphones, a Remote Control or an External Monitor ................ 125 Headphones ........................................ 125 Remote control .................................... 125 External monitor .................................. 126 Setting the external output resolution ............................................. 128 Connecting to a PC (File transfer/nonlinear editing) ............
PAGE 11
HC-X1_E_GC_DVQP1176ZA_eng.book 11 ページ２０１６年１１月２８日月曜日午前１１時４０分 Accessories Check the accessories before using this unit. Keep the accessories out of reach of children to prevent swallowing. Product numbers correct as of November 2016. These may be subject to change.
PAGE 12
HC-X1_E_GC_DVQP1176ZA_eng.book 12 ページ２０１６年１１月２８日月曜日午前１１時４０分 Optional accessories Some optional accessories may not be available in some countries. Product numbers correct as of November 2016. These may be subject to change. Unidirectional microphone (AG-MC200G) Battery pack (VW-VBD58/AG-VBR59/AG-VBR89/AG-VBR118) Battery charger (AG-B23/AG-BRD50*) LED video light (VW-LED1) * The AG-BRD50 is available for purchase as an optional accessory package containing a battery charger, AC adaptor, and AC cable.
PAGE 13
HC-X1_E_GC_DVQP1176ZA_eng.book 13 ページ２０１６年１１月２８日月曜日午前１１時４０分 Preparation What you can do with this unit Recording to the SD card It is possible to record motion pictures and still pictures to the SD card using a variety of recording functions. ≥ This unit supports relay/simultaneous/background/dual codec recording using double card slots. Linking to external devices USB Device Mode Transfer data (files) to perform nonlinear editing on another device (PC, etc.). ≥ This unit supports USB 3.0.
PAGE 14
HC-X1_E_GC_DVQP1176ZA_eng.book 14 ページ２０１６年１１月２８日月曜日午前１１時４０分 USB Host Mode If you connect an external media device, such as USB HDD or USB flash memory (commerciallyavailable) to this unit, you can copy motion pictures and still pictures recorded on this unit to the external media device. It can also play back the scenes and still pictures copied to the external media device. ≥ This unit supports USB 3.0. Refer to the following support site for information about an external media device.
PAGE 15
HC-X1_E_GC_DVQP1176ZA_eng.book 15 ページ２０１６年１１月２８日月曜日午前１１時４０分 Remote operations with an iPad Attaching a wireless module that support this unit (l 142) to the USB HOST terminal of this unit allows you to connect to a wireless LAN network.
PAGE 16
HC-X1_E_GC_DVQP1176ZA_eng.
PAGE 17
HC-X1_E_GC_DVQP1176ZA_eng.book 17 ページ２０１６年１１月２８日月曜日午前１１時４０分 26 27 31 32 33 34 28 29 30 40 41 35 36 37 38 39 42 43 26 Tripod receptacle ≥ There are tripod mounting holes that are compatible with 1/4-20UNC and 3/8-16UNC screws. Use the size that matches the diameter of the tripod’s fixing screw. ≥ Attaching a tripod with a screw length of 5.5 mm or more may damage the unit.
PAGE 18
HC-X1_E_GC_DVQP1176ZA_eng.
PAGE 19
HC-X1_E_GC_DVQP1176ZA_eng.book 19 ページ２０１６年１１月２８日 75 76 月曜日午前１１時４０分 77 78 79 80 81 82 83 84 85 75 Accessory shoe 76 Sub zoom lever (l 48, 174) ≥ This lever functions in the same manner as the zoom lever. ≥ The zoom speed is controlled with this lever in a way different from the way it is controlled with the zoom lever.
PAGE 20
HC-X1_E_GC_DVQP1176ZA_eng.book 20 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Attaching/detaching the lens hood (How to detach the lens hood) While pressing and holding the lens hood release button, rotate the lens hood in the direction of the arrow to detach it. A  Lens hood release button (How to attach the lens hood)   B 1 Mounting mark Fit the lens hood into this unit. ≥ Align the mounting mark on the lens hood with the mounting mark on this unit.
PAGE 21
HC-X1_E_GC_DVQP1176ZA_eng.book 21 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Adjust the length of the hand strap so that it fits your hand. Adjust the hand strap according to the size of your hand. ≥ If you find it difficult to fasten the buckle B, move the pad A forward, and fasten the buckle B again. 1 2  Open the buckle. Pull the end of the belt.    ∫ Attaching the eye cup 1 2 Align the mounting mark on the eye cup mount with the corresponding mark on the eyecup.
PAGE 22
HC-X1_E_GC_DVQP1176ZA_eng.book 22 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Attaching the front microphone ≥ The microphone holder is set up so that a 21 mm external microphone (AG-MC200G: optional) can be attached. Check in advance whether the microphone you wish to use can be attached. 1 Attach the microphone holder to the microphone holder attachment part. ≥ Attach by using a commercially available screw driver.
PAGE 23
HC-X1_E_GC_DVQP1176ZA_eng.book 23 ページ２０１６年１１月２８日月曜日午前１１時４０分 Preparation Power supply ∫ About batteries that you can use with this unit (as of November 2016) The battery that can be used with this unit is VW-VBD58/AG-VBR59/AG-VBR89/AG-VBR118. ≥ The AG-VBR59/AG-VBR89/AG-VBR118 supports quick charging. It has been found that counterfeit battery packs which look very similar to the genuine product are made available to purchase in some markets.
PAGE 24
HC-X1_E_GC_DVQP1176ZA_eng.book 24 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Charging the battery 1 2   Connect the AC mains lead to the AC adaptor. ≥ Perform step 2 first, and then step 3. Insert the AC mains lead all the way in until it stops. 3   Connect the DC plug of the AC adaptor to the DC IN 12 V connector of battery charger. Insert the battery into the battery charger. ≥ Slide the battery horizontally into the battery charger along the “ ” mark.
PAGE 25
HC-X1_E_GC_DVQP1176ZA_eng.book 25 ページ２０１６年１１月２８日 Inserting/removing the battery Install the battery by inserting it in the direction shown in the figure. ≥ Insert the battery until it clicks and locks. Removing the battery Make sure that the power switch is set to OFF and the status indicator is turned off, and then remove by holding onto it taking care not to drop. (l 31) While pressing the battery release button, remove the battery.
PAGE 26
HC-X1_E_GC_DVQP1176ZA_eng.book 26 ページ２０１６年１１月２８日月曜日午前１１時４０分 Charging and recording time Charging/Recording time Battery model number Voltage/Capacity (minimum) Charging time Supplied battery/ AG-VBR59 (optional) 7.28 V/5900 mAh 3 h 20 min AG-VBR89 (optional) 7.28 V/8850 mAh 4h AG-VBR118 (optional) VW-VBD58 (optional) 7.28 V/11800 mAh 7.2 V/5800 mAh 4 h 40 min 5 h 20 min System Frequency setting (l 160) Continuously recordable time 59.94 Hz 3 h 25 min 50.00 Hz 3 h 35 min 59.
PAGE 27
HC-X1_E_GC_DVQP1176ZA_eng.book 27 ページ２０１６年１１月２８日月曜日午前１１時４０分 Checking the remaining power of the battery You can check the remaining power of the battery by looking at the battery capacity indication displayed on this unit's screen or by looking at the supplied battery AG-VBR59. ∫ Checking the remaining power using this unit Battery capacity indication ≥ The display changes as the battery capacity reduces. If the battery discharges, then will flash red.
PAGE 28
HC-X1_E_GC_DVQP1176ZA_eng.book 28 ページ２０１６年１１月２８日月曜日午前１１時４０分 Connecting to the AC outlet The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always “live” as long as the AC adaptor is connected to an electrical outlet. Important: ≥ Use the supplied AC adaptor. Do not use the AC adaptor of another device. ≥ Do not use the AC cable with any other equipment as it is designed only for this unit. Also, do not use the AC cable from other equipment with this unit.
PAGE 29
HC-X1_E_GC_DVQP1176ZA_eng.book 29 ページ２０１６年１１月２８日月曜日午前１１時４０分 Preparation Preparation of SD cards The unit can record motion pictures or still pictures to an SD card. Cards that you can use with this unit ≥ The cards that you can use are correct as of November 2016. ≥ We recommend that you use a Panasonic Memory Card. Card type Capacity SDHC Memory Card SDXC Memory Card 4 GB to 32 GB 48 GB to 128 GB ≥ We do not guarantee the operation of SD cards other than the ones above.
PAGE 30
HC-X1_E_GC_DVQP1176ZA_eng.book 30 ページ２０１６年１１月２８日月曜日午前１１時４０分 Inserting/removing an SD card When using an SD card for the first time, it is necessary to format the SD card. (l 42) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored. Caution: Check that the access lamp has gone off. Access lamp A ≥ When this unit is accessing the SD card, the access lamp lights up.
PAGE 31
HC-X1_E_GC_DVQP1176ZA_eng.book 31 ページ２０１６年１１月２８日月曜日午前１１時４０分 Preparation Turning the unit on/off Set the power switch to ON while pressing the lock release button B to turn on the unit.  OFF To turn off the unit Set the power switch to OFF while pressing the lock release button. The status indicator goes off. ON  A The status indicator lights on. ≥ To turn on the unit again after the [ECONOMY (BATT)] or [ECONOMY (AC)] is activated, set the power switch to OFF once, and then to ON again.
PAGE 32
HC-X1_E_GC_DVQP1176ZA_eng.book 32 ページ２０１６年１１月２８日月曜日午前１１時４０分 Preparation Using the LCD monitor/Viewfinder Setting how to turn on/off the LCD monitor and Viewfinder Select the menu. (l 40) MENU : [OUTPUT SETUP] # [LCD/EVF OUTPUT] # desired setting [AUTO]: The LCD monitor is turned on when the LCD monitor is extracted. When you move your eye closer to the eye cup of the viewfinder, the LCD monitor is turned off, and the viewfinder is turned on.
PAGE 33
HC-X1_E_GC_DVQP1176ZA_eng.book 33 ページ２０１６年１１月２８日月曜日午前１１時４０分 Using the LCD monitor 1 Extract the LCD monitor in the direction as indicated in the figure. ≥ Hold the LCD monitor extract part A, and extract the LCD monitor until it clicks into position. 2  Rotate to the position that is easy to view. To retract the LCD monitor Retract as shown in the figure with the LCD facing downward. Range of rotation of the LCD monitor ≥ It can rotate up to 270o towards the lens.
PAGE 34
HC-X1_E_GC_DVQP1176ZA_eng.book 34 ページ２０１６年１１月２８日月曜日午前１１時４０分 How to use the touch screen You can operate by directly touching the LCD monitor (touch screen) with your finger. ∫ Touch Touch and release the touch screen to select icon or picture. ≥ Touch the center of the icon. ≥ Touching the touch screen will not operate while you are touching another part of the touch screen. ∫ Slide while touching Move your finger while pressing on the touch screen.
PAGE 35
HC-X1_E_GC_DVQP1176ZA_eng.book 35 ページ２０１６年１１月２８日月曜日午前１１時４０分 LCD monitor adjustment ≥ These settings will not affect the images actually recorded. [POWER LCD] This makes it easier to view the LCD monitor in bright places including outdoors. Select the menu. (l 40) MENU : [DISP SETUP] # [POWER LCD] # [+1] (Makes brighter)/[0] (Normal)/[-1] (Makes less bright) ≥ When the AC adaptor is in use, [POWER LCD] is set to [+1] automatically.
PAGE 36
HC-X1_E_GC_DVQP1176ZA_eng.book 36 ページ２０１６年１１月２８日月曜日午前１１時４０分 Viewfinder adjustment ≥ These settings will not affect the images actually recorded. Adjusting the field of view It adjusts the field of view to show the image on the viewfinder clearly. 1 Adjust the viewfinder to suit your vision so that you can see the display images clearly. ≥ Be careful not to trap your fingers when moving the viewfinder. ≥ The viewfinder can be lifted vertically up to approximately 90o.
PAGE 37
HC-X1_E_GC_DVQP1176ZA_eng.book 37 ページ２０１６年１１月２８日月曜日午前１１時４０分 [EVF COLOUR] The recording images or playback images on the viewfinder can be selected between color/black and white. Select the menu. (l 40) MENU : [DISP SETUP] # [EVF COLOUR]# [ON] or [OFF] [ON]: Displayed in color [OFF]: Displayed in black and white ≥ If you adjust the [COLOUR] setting in [EVF SETTING], [EVF COLOUR] will be set to [ON]. [EYE SENSOR] It adjusts sensitivity of eye sensor. 1 Select the menu.
PAGE 38
HC-X1_E_GC_DVQP1176ZA_eng.book 38 ページ２０１６年１１月２８日月曜日午前１１時４０分 Preparation Setting date and time When this unit is turned on, the message [SET TIME ZONE AND DATE/TIME] may appear. To make these settings, select [YES], and follow the instructions from Step 2-3 of the time zone setting procedure. Time zone Time difference from the Greenwich Mean Time can be set. 1 Select the menu. (l 40) MENU 2 3 : [OTHER FUNCTION] # [TIME ZONE] Touch / and set the region to record.
PAGE 39
HC-X1_E_GC_DVQP1176ZA_eng.
PAGE 40
HC-X1_E_GC_DVQP1176ZA_eng.book 40 ページ２０１６年１１月２８日 Preparation Using the menu screen ≥ You can also select menu items by operating the jog dial. (l 110) MENU 1 2 3 Press the MENU button MENU . Touch the top menu A. Touch the submenu B. ≥ Next (Previous) page can be displayed by touching / . 4 5 Touch the desired item to enter the setting. Touch [EXIT] to exit the menu setting.
PAGE 41
HC-X1_E_GC_DVQP1176ZA_eng.book 41 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Before recording When recording, make sure your footing is stable and there is no danger of colliding with another person or object. Hold the eye cup of the viewfinder as close as possible to your eye. Adjust the angle of the LCD monitor according to the position in which the unit is held. When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it will become dark in the recording.
PAGE 42
HC-X1_E_GC_DVQP1176ZA_eng.book 42 ページ２０１６年１１月２８日月曜日午前１１時４０分 Formatting media If you use the SD cards for the first time for recording with this unit, format the cards. Please be aware that if a medium is formatted, then all the data recorded on the medium will be erased and cannot be restored. Back up important data on a PC etc. (l 132) ≥ When using two SD cards, format both SD cards. 1 Select the menu. MENU 2 : [OTHER FUNCTION] # [FORMAT MEDIA] Touch [SD CARD 1] or [SD CARD 2].
PAGE 43
HC-X1_E_GC_DVQP1176ZA_eng.book 43 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Screen indications in the Recording Mode TC 00:00:00:00 R 1h20m MAIN R 1h20m 150M 50.00p TC 00:00:00:00 / (White) Counter display (l 78) Card slot number R 1h20m Approximate remaining recordable time ≥ When the remaining time is less than 1 minute, R 0h00m flashes red. Card slot selected for motion picture recording (l 41)* MAIN Recording format (l 161) 150M Bit rate (l 161) Recording mode (l 160) 50.
PAGE 44
HC-X1_E_GC_DVQP1176ZA_eng.book 44 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Switching between Auto and Manual Mode MANU AUTO/MANU switch Slide the switch to change Auto Mode/Manual Mode. ≥ is displayed in the Auto Mode. ∫ Auto Mode In Auto Mode, this unit operates according to the [AUTO SW] menu settings.
PAGE 45
HC-X1_E_GC_DVQP1176ZA_eng.book 45 ページ２０１６年１１月２８日 Menu item [AF] 月曜日午前１１時４０分 Setting [ON]: Activates Auto Focus in Auto Mode. [OFF]: Activates Auto Focus as a manual mode. Focus is adjusted according to the functions of the FOCUS A/M/¶ switch. Automatic Tracking White Balance The Auto Tracking White (ATW) Balance function of this unit automatically adjusts the White Balance according to the lighting condition.
PAGE 46
HC-X1_E_GC_DVQP1176ZA_eng.book 46 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Adjusting the Picture Quality You can set the picture quality of images to be recorded in the main menu # [SCENE FILE]. Detail function This function thickens or weakens the outlines of images. It effectively softens or sharpens images, but in some cases, the whole image may become rough due to emphasized noise and edges.
PAGE 47
HC-X1_E_GC_DVQP1176ZA_eng.book 47 ページ２０１６年１１月２８日月曜日午前１１時４０分 Color correction function This function sets color saturation and phase. It applies individual effect on 16 phases in an image. It can be set to individual color hue. ∫ Menu item [COLOR CORRECTION SETTING] (l 156) Black control function This function sets the black level that is to be the reference of luminance. ∫ Menu item [MASTER PED] (l 157) Gamma function This function optimizes the tone of images.
PAGE 48
HC-X1_E_GC_DVQP1176ZA_eng.book 48 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Using the zoom The unit can deliver a maximum optical zoom of 20k. ≥ (When the picture size of [REC FORMAT] (l 161) is 1920k1080 or below) It can zoom up to approx. 30k when the [i.Zoom] is set to [ON]. (l 49) ≥ You can check the zoom magnification on-screen, displayed as a value between Z00 and Z99. The value gets larger as you zoom in, and smaller as you zoom out.
PAGE 49
HC-X1_E_GC_DVQP1176ZA_eng.book 49 ページ２０１６年１１月２８日月曜日午前１１時４０分 Using the i.Zoom When [i.Zoom] is set to [ON], you can zoom in while maintaining the beauty of high-definition picture quality up to a magnification of approx. 30k. ≥ Set [REC FORMAT] to a setting with a picture size of 1920k1080 or below. (l 161) Select the menu. MENU : [SW SETUP] # [i.Zoom] # [ON] ≥ You can also use i.Zoom by registering [i.ZOOM] to a USER button. (l 102) ≥ The zoom magnification display will change.
PAGE 50
HC-X1_E_GC_DVQP1176ZA_eng.book 50 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Image Stabilizer Function Use the Image Stabilizer to reduce the effects of shake during recording. This unit is equipped with Hybrid Optical Image Stabilizer. Hybrid Optical Image Stabilizer is a hybrid of Optical and Electrical Image Stabilizer. 1 Register [O.I.S.] to a USER button. (l 82) ≥ This function is registered to the USER6 button by default. 2 Press the USER button to which [O.I.S.
PAGE 51
HC-X1_E_GC_DVQP1176ZA_eng.book 51 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ The setting is fixed to [OFF] in the following case: j When the size in [REC FORMAT] is set to 4K (4096k2160) (l 161) ∫ Blur amplitude You can adjust the performance of camera shake correction according to the level of camera shake during recording. Select the menu.
PAGE 52
HC-X1_E_GC_DVQP1176ZA_eng.book 52 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Focus Perform focus adjustments using the focus ring. If auto focusing is difficult due to the conditions, then use Manual Focus. A B C FOCUS A M ∞  PUSH AUTO FOCUS A/M/¶ switch PUSH AUTO button Focus ring   ≥ Switch to Manual Mode. (l 44) 1 Set the FOCUS A/M/¶ switch to [M] to enable Manual Focus. ≥ It will switch to MF from AF. 2 Adjust the focus by rotating the focus ring.
PAGE 53
HC-X1_E_GC_DVQP1176ZA_eng.book 53 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ To change the way you adjust focus with the focus ring Select the menu. MENU : [SW SETUP] # [FOCUS RING DRIVE] [SPEED]: Adjusts the focus value according to the speed at which the focus ring is rotated. [COARSE]: Adjusts the focus value according to the rotational position of the focus ring. Since the operation of the focus ring results in a greater change in focus value, this setting is suitable for making rough adjustments.
PAGE 54
HC-X1_E_GC_DVQP1176ZA_eng.book 54 ページ２０１６年１１月２８日月曜日午前１１時４０分 Customizing Auto Focus for various recording conditions You can customize Auto Focus for various recording conditions by adjusting the settings of [AF SPEED], [AF SENSITIVITY], and [AF AREA WIDTH] individually. ∫ Custom AF function When [ON] is selected, Auto Focus works with customized [AF SPEED] and [AF SENSITIVITY] settings. ≥ Switch to Auto Focus Mode. (l 52) Select the menu.
PAGE 55
HC-X1_E_GC_DVQP1176ZA_eng.book 55 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ AF Area Width Adjustment You can adjust the effective area width for Auto Focus according to the size of the subject. ≥ Switch to Auto Focus Mode. (l 52) 1 Select the menu. MENU : [SW SETUP] # [AF AREA WIDTH] # [SET] 2 Push the jog dial. 3 Rotate the jog dial to adjust the AF area frame. A B C [RETURN] AF area frame [EXIT] 4 Touch [EXIT] to complete the setting. ≥ AF-AREA will be displayed on the screen.
PAGE 56
HC-X1_E_GC_DVQP1176ZA_eng.book 56 ページ２０１６年１１月２８日月曜日午前１１時４０分 Push AF If you press and hold the PUSH AUTO button, Manual Focus will be temporarily switched to Auto Focus. ≥ Set this unit to Manual Focus. (l 52) Press and hold the PUSH AUTO button. ≥ The focus position will be automatically adjusted for the subject at the center of the screen.
PAGE 57
HC-X1_E_GC_DVQP1176ZA_eng.book 57 ページ２０１６年１１月２８日月曜日午前１１時４０分 Using Focus Assist ≥ Switch to Manual Focus Mode. (l 52) Press the FOCUS ASSIST button or the USER button to which [FOCUS ASSIST 1] or [FOCUS ASSIST 2] is registered. FOCUS ASSIST ≥ You can also use Focus Assist by touching the USER button icon to which [FOCUS ASSIST 1] or [FOCUS ASSIST 2] is registered.
PAGE 58
HC-X1_E_GC_DVQP1176ZA_eng.book 58 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ To change the peaking settings  If you set Focus Assist to ON by following either of the procedures below, in-focus portions are highlighted with color (peaking). j Setting the menu item [FOCUS ASSIST 1] to [PEAKING] or [BOTH] and pressing the FOCUS ASSIST button or the USER button to which [FOCUS ASSIST 1] is registered.
PAGE 59
HC-X1_E_GC_DVQP1176ZA_eng.book 59 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ Peaking may not be displayed when you use Digital Zoom (l 87). To zoom in and use peaking at the same time, we recommend increasing the magnification level of the magnified display by setting [FOCUS ASSIST 1] to [BOTH] or by using the magnified display and the peaking function in combination. (Notes on the peaking of Focus Assist) ≥ When EVF/LCD detail is enabled, Focus Assist is canceled.
PAGE 60
HC-X1_E_GC_DVQP1176ZA_eng.book 60 ページ２０１６年１１月２８日月曜日午前１１時４０分 Focus Transition You can use Focus Transition by registering [FOCUS TRANS] to a USER button. With Focus Transition, you can shift the current focus position to a pre-registered focus position. ≥ Please refer to page 82 for details about setting the USER button. Registering a focus position To use Focus Transition, you need to register a focus position. ≥ You can register up to 3 focus positions. ≥ Switch to Manual Focus Mode.
PAGE 61
HC-X1_E_GC_DVQP1176ZA_eng.book 61 ページ２０１６年１１月２８日月曜日午前１１時４０分 Using Focus Transition ≥ Select the [FOCUS TRANSITION] menu. (l 60) ≥ Register [FOCUS TRANS] to a USER button. (l 82) 1 2 3 Switch to Manual Focus Mode. (l 52) Press the USER button to which [FOCUS TRANS] is registered or touch the applicable USER button icon. Touch a registered item ([1]s[3]). ≥ Focus Transition will start. Focus will shift slowly from the current position to the registered position. This will take a few seconds.
PAGE 62
HC-X1_E_GC_DVQP1176ZA_eng.book 62 ページ２０１６年１１月２８日月曜日午前１１時４０分 To set the Focus Transition time 1 Select the menu. MENU 2 : [RECORD SETUP] # [FOCUS TRANSITION TIME] Touch the desired setting item. [DIRECT]/[FASTEST]/[2-15 SEC.]/[20 SEC.]/[30 SEC.]/[45 SEC.]/[60 SEC.]/[90 SEC.] ≥ If you select [DIRECT], the focus position changes as soon as Focus Transition starts, but the operating noise of the lens may be recorded. 3 (If you have selected [2-15 SEC.] in Step 2) Touch / to set the duration.
PAGE 63
HC-X1_E_GC_DVQP1176ZA_eng.book 63 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording White Balance Automatic White Balance function may not reproduce natural colors depending on the scenes or lighting conditions. If so, you can adjust the White Balance manually. 5600K Ach  ヴユロバヱヶヴラヴユヵ   WHITE BAL  A White Balance B Color temperature display ≥ Displayed when the White Balance mode is set to Ach or Bch. ≥ The color temperature display is not guaranteed to indicate an exact value.
PAGE 64
HC-X1_E_GC_DVQP1176ZA_eng.book 64 ページ２０１６年１１月２８日月曜日午前１１時４０分 About White Balance modes Display (Mode) Settings ATW (ATW)*1 It will automatically adjust in accordance with the recording condition. LOCK (ATW Lock)*2 It will lock the setting for ATW. (l 65) P3200K (P3200K) Preset value for studio/indoor recording (halogen lamp, etc.) P5600K (P5600K) Preset value for outdoors VAR (VAR) Setting can be finely adjusted in accordance to the recording conditions.
PAGE 65
HC-X1_E_GC_DVQP1176ZA_eng.book 65 ページ２０１６年１１月２８日月曜日午前１１時４０分 Customizing ATW for various recording conditions You can customize the ATW settings for various recording conditions by adjusting the settings of [ATW TARGET R] and [ATW TARGET B] individually. ∫ Fine-adjusting the color balance of ATW 1 Select the menu. MENU : [SW SETUP] # [ATW TARGET R] or [ATW TARGET B] ≥ [ATW TARGET R] adjusts the intensity of red. ≥ [ATW TARGET B] adjusts the intensity of blue. 2 Touch / to adjust settings.
PAGE 66
HC-X1_E_GC_DVQP1176ZA_eng.book 66 ページ２０１６年１１月２８日月曜日午前１１時４０分 To finely adjust the White Balance Setting the White Balance mode to [VAR] allows you to set a White Balance value between 2000K and 15000K. ≥ Use the jog dial to change the settings. ≥ Switch to Manual Mode. (l 44) 1 Set the White Balance mode to [VAR]. (l 63) 2 Rotate the jog dial to adjust the color balance. 3 Push the jog dial to finish the adjustment. ≥ You can also access this setting by selecting menu items.
PAGE 67
HC-X1_E_GC_DVQP1176ZA_eng.book 67 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Iris/Gain adjustment When recording a scene that is too dark (or bright) or a scene in a similar situation, manually adjust the iris and gain. Iris adjustment F4.0 IRIS    A Iris value B Auto iris icon* * It is displayed in Auto Iris Mode. 1 2  IRIS button Iris ring ≥ Switch to Manual Mode. (l 44) 1 ≥ 2 Press the IRIS button to switch to Manual Iris Mode. disappears. Adjust the iris by rotating the iris ring.
PAGE 68
HC-X1_E_GC_DVQP1176ZA_eng.book 68 ページ２０１６年１１月２８日月曜日午前１１時４０分 Customizing Auto Iris motion settings for various recording conditions You can customize Auto Iris motion settings for various recording conditions by adjusting the settings of [AUTO IRIS LEVEL] and [AUTO IRIS LEVEL EFFECT] individually. ∫ Adjusting brightness during the Auto Iris Mode 1 Select the [AUTO IRIS LEVEL EFFECT] menu. MENU 2 : [SCENE FILE] # [AUTO IRIS LEVEL EFFECT] Touch / to adjust settings.
PAGE 69
HC-X1_E_GC_DVQP1176ZA_eng.book 69 ページ２０１６年１１月２８日月曜日午前１１時４０分 Gain adjustment ≥ Use the jog dial to change the settings. 0dB  ヴユロバヱヶヴラヴユヵ  GAIN 1 2   Jog dial GAIN button A Gain value ≥ In Auto Gain Mode, “AGC” is displayed; in Manual Gain Mode, the gain value is displayed in dB. B [GAIN] ≥ Switch to Manual Mode. (l 44) 1 Press the GAIN button to switch to [LOW GAIN], [MID GAIN], or [HIGH GAIN]. ≥ The setting changes each time you press the button.
PAGE 70
HC-X1_E_GC_DVQP1176ZA_eng.book 70 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ It is not possible to adjust the gain value using the GAIN button and jog dial in the following situations: j During Freeze Frame (l 89) ≥ If the gain value is increased, the noise on the screen increases. ≥ In Auto Iris Mode or Auto Shutter Mode, the screen brightness may not change even if you adjust the gain.
PAGE 71
HC-X1_E_GC_DVQP1176ZA_eng.book 71 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Manual shutter speed Adjust the shutter speed when recording fast-moving subjects. ≥ Use the jog dial to change the settings. SHUTTER A.SHTR 1/60    ヴユロバヱヶヴラヴユヵ A Shutter speed B Auto Shutter display ≥ This is displayed in Auto Shutter Mode. C [SHUTTER] 1 2   SHUTTER button Jog dial ≥ Switch to Manual Mode. (l 44) 1 2 Press the SHUTTER button to switch to Manual Shutter Mode.
PAGE 72
HC-X1_E_GC_DVQP1176ZA_eng.book 72 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Shutter speed guide for fast moving subjects Refer to the table below to reduce afterimages that appear when playback is paused. Subject Shutter speed Golf or tennis shot 1/500 to 1/2000 Roller coaster 1/500 to 1/1000 ≥ The shutter speed cannot be adjusted in the following cases: j During Freeze Frame (l 89) ≥ You may see a band of light around an object that is shining very bright, or highly reflective.
PAGE 73
HC-X1_E_GC_DVQP1176ZA_eng.book 73 ページ２０１６年１１月２８日月曜日午前１１時４０分 Making adjustments with Synchro Scan If you press the jog dial when the shutter speed is displayed as a decimal number, the Synchro Scan setting will be displayed. You can fine-adjust the shutter speed by adjusting the Synchro Scan setting. This will minimize flickering and horizontal bars in images. 1 2 Press the SHUTTER button. When the shutter is displayed as a decimal number (e.g., 1/60.0), press the jog dial.
PAGE 74
HC-X1_E_GC_DVQP1176ZA_eng.book 74 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Audio Input This unit can record audio in 2 ch. It is possible to switch between built-in microphone, external microphone, or connected audio equipment for each channel. ∫ About audio recording methods The audio recording method varies depending on the [REC MODE] setting.
PAGE 75
HC-X1_E_GC_DVQP1176ZA_eng.book 2 75 ページ２０１６年１１月２８日月曜日午前１１時４０分 Use INPUT1 or INPUT2 switches to switch the connected audio input signal. LINE*1: Audio equipment is connected MIC*2: An external microphone is connected +48V*2: When using a phantom microphone (which requires a power supply of +48 V) *1 The input level varies depending on the [INPUT1 LINE LEVEL] or [INPUT2 LINE LEVEL] setting. (l 187) *2 The input level varies depending on the [INPUT1 MIC LEVEL] or [INPUT2 MIC LEVEL] setting.
PAGE 76
HC-X1_E_GC_DVQP1176ZA_eng.book 76 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ Set INPUT1, 2 switches to LINE or MIC if you connect equipment not compatible with +48 V. You can damage this unit or such equipment if you leave the setting at [+48V]. ≥ This unit is turned off when a problem occurs with the +48 V power supply. ≥ The battery will discharge faster if you use a phantom microphone.
PAGE 77
HC-X1_E_GC_DVQP1176ZA_eng.book 77 ページ２０１６年１１月２８日月曜日午前１１時４０分 Using the ALC function ALC can reduce audio noise. For audio channel 1, select [AUDIO ALC CH1]: for audio channel 2, select [AUDIO ALC CH2]. 1 2 Set [AUDIO LEVEL CH1]/[AUDIO LEVEL CH2] to [MANUAL]. (l 76) Select the menu. MENU : [AUDIO SETUP] # [AUDIO ALC CH1] or [AUDIO ALC CH2] # desired setting [ON]: Enables ALC, allowing you to record audio with reduced noise. [OFF]: Allows you to record natural-sounding audio.
PAGE 78
HC-X1_E_GC_DVQP1176ZA_eng.book 78 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Counter display You can change a counter display that indicates how much time has elapsed during recording or playback.   A B COUNTER COUNTER button RESET button RESET Press the COUNTER button to switch the counter display. ≥ The display will be switched in the following order: Time Code # User Information* # Recording Counter # Off. Counter display Indications Time Code TC 00:00:00:00 or TC 00:00:00.
PAGE 79
HC-X1_E_GC_DVQP1176ZA_eng.book 79 ページ２０１６年１１月２８日月曜日午前１１時４０分 [DF MODE] Select the compensation mode for the time code. ≥ Set [SYSTEM FREQ] to [59.94Hz]. (l 160) Select the menu. MENU : [RECORD SETUP] # [DF MODE] # desired setting [DF]: Time code is compensated in accordance with the actual time. It is mainly used for broadcasting such as TV programs. [NDF]: It will not compensate the time code.
PAGE 80
HC-X1_E_GC_DVQP1176ZA_eng.book 80 ページ２０１６年１１月２８日月曜日午前１１時４０分 [TC PRESET] You can set the initial time code. 1 Select the menu. MENU 2 : [RECORD SETUP] # [TC PRESET] Touch the item to set and change with / . ≥ The value will be set to 00h00m00s00f if you press the RESET button. ≥ “h” is an abbreviation for hour, “m” for minute, “s” for second and “f” for frame. 3 Touch [EXIT] to complete the setting.
PAGE 81
HC-X1_E_GC_DVQP1176ZA_eng.book 81 ページ２０１６年１１月２８日月曜日午前１１時４０分 Setting the Recording Counter Recording Counter will display the recording time in seconds. 0:00:00 (hour : minute : second (When [REC COUNTER] is set to [TOTAL])) SCN 0:00:00 (hour : minute : second (When [REC COUNTER] is set to [SCENE])) [REC COUNTER] Select the counting method during the recording. Select the menu.
PAGE 82
HC-X1_E_GC_DVQP1176ZA_eng.book 82 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording USER button Each of the USER button can register one function from the 44 available functions. ≥ There are 9 USER buttons (USER1 to 9) on the main body and 4 USER button icons (USER10 to USER13) displayed on the LCD monitor. Setting the USER button 1 Select the menu. MENU : [USER SW] # [USER1] to [USER13] ≥ It is not possible to register functions to [USER10] to [USER13] in Playback Mode. 2 Touch the item to register.
PAGE 83
HC-X1_E_GC_DVQP1176ZA_eng.book 83 ページ２０１６年１１月２８日月曜日午前１１時４０分 Using the USER button To use the function assigned to a USER button or USER button icon, press the applicable USER button (one of the USER buttons 1 to 9), or touch the applicable USER button icon (one of the USER button icons 10 to 13) while operation icons are displayed. (When you use the USER1 to USER7 button) (When you use the USER8 button) LCD/EVF O.I.S.
PAGE 84
HC-X1_E_GC_DVQP1176ZA_eng.book 84 ページ２０１６年１１月２８日月曜日 Functions of the USER button ∫ List of USER button functions Item [INHIBIT] Icon [INH] Function Invalid [FOCUS ASSIST 1] [FA1] Focus Assist 1 [BACKLIGHT] [B.Light] Backlight Compensation [SPOTLIGHT] [S.Light] Spotlight [BLACK FADE] [B.FD] Black Fade [WHITE FADE] [W.FD] White Fade [ATW] [ATW] Auto Tracking White Balance [ATW LOCK] [ATW.L] ATW Lock [D.ZOOM] [D.
PAGE 85
HC-X1_E_GC_DVQP1176ZA_eng.book 85 ページ Item [AF AREA] ２０１６年１１月２８日 Icon [AF Area] 月曜日 Function AF Area Width adjustment [VFR] [VFR] Variable Frame Rate Mode [FOCUS MACRO] [F.Macro] Focus Macro [i.ZOOM] [i.Zoom] i.
PAGE 86
HC-X1_E_GC_DVQP1176ZA_eng.book 86 ページ２０１６年１１月２８日月曜日午前１１時４０分 [SPOTLIGHT] ≥ Register [SPOTLIGHT] to a USER button. (l 82) Switches to automatic iris control for spotlight. Very bright object is recorded clearly. ≥ appears when it is set. ≥ Canceling [SPOTLIGHT] resets the iris mode to the previous setting. ≥ This item cannot be set during Freeze Frame. (l 89) [BLACK FADE] ≥ Register [BLACK FADE] to a USER button.
PAGE 87
HC-X1_E_GC_DVQP1176ZA_eng.book 87 ページ２０１６年１１月２８日月曜日午前１１時４０分 [ATW] ≥ Register [ATW] to a USER button. (l 82) The White Balance can be changed to [ATW]. (l 64) ≥ This function is not available when the White Balance mode is set to [ATW LOCK]. [ATW LOCK] ≥ Register [ATW LOCK] to a USER button. (l 82) This sets the White Balance mode to [ATW LOCK].(l 65) [D.ZOOM] ≥ Register [D.ZOOM] to a USER button. (l 82) Press USER button or touch USER button icon in the recording screen.
PAGE 88
HC-X1_E_GC_DVQP1176ZA_eng.book 88 ページ２０１６年１１月２８日月曜日午前１１時４０分 [FOCUS ASSIST 2] ≥ Register [FOCUS ASSIST 2] to a USER button. (l 82) You can set the Focus Assist. (l 56) ≥ You can set the Focus Assist method in [FOCUS ASSIST 2] in the [SW SETUP] menu. ≥ When [FOCUS ASSIST 1] in the [SW SETUP] menu is set to [BOTH], the USER button is disabled. [REC CHECK] ≥ Register [REC CHECK] to a USER button. (l 82) Approximately 2 seconds at the end of the video recorded last can be played back.
PAGE 89
HC-X1_E_GC_DVQP1176ZA_eng.book 89 ページ２０１６年１１月２８日月曜日午前１１時４０分 [DRS] ≥ Register [DRS] to a USER button. (l 82) Selects the DRS (Dynamic Range Stretcher) function. It is possible to expand the dynamic range by compressing the video signal level of the highly illuminated area that gets washed out with standard recording.
PAGE 90
HC-X1_E_GC_DVQP1176ZA_eng.book 90 ページ２０１６年１１月２８日月曜日午前１１時４０分 [AREA] You can apply a variety of effects to the subject you touch. ∫ Setting an Area Mode effect You can select the following menu items to set an effect to be applied when you touch the subject. MENU : [SW SETUP] # [AREA MODE] # desired setting [INH]: Does not apply any effects of Area Mode. [FOCUS]: Optimizes the focus automatically for the subject you touch. [IRIS]: Optimizes the iris automatically for the subject you touch.
PAGE 91
HC-X1_E_GC_DVQP1176ZA_eng.book 91 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ Area mode is not possible in following cases: j During Super Slow Recording (l 103) j In Variable Frame Rate Mode (l 100) j During AG ROP application connection (l 141) ≥ Area mode is canceled in following cases: j If you turn the unit off j If you press the THUMBNAIL button j If you switch to a [REC FORMAT] setting with a frame rate of 24.00p.
PAGE 92
HC-X1_E_GC_DVQP1176ZA_eng.book 92 ページ２０１６年１１月２８日月曜日午前１１時４０分 [IR REC] ≥ Register [IR REC] to a USER button. (l 82) This changes the Infrared Recording Mode setting. ≥ This unit operates as follows in Infrared Recording Mode: j appears on the screen. j The iris, gain, and shutter speed are adjusted automatically. j When [AUTO SLOW SHTR] is set to [ON], the shutter speed will be automatically adjusted to 1/30, 1/24 or 1/25. (l 176) It is recommended to use a tripod.
PAGE 93
HC-X1_E_GC_DVQP1176ZA_eng.book 93 ページ２０１６年１１月２８日月曜日午前１１時４０分 [LEVEL GAUGE] ≥ Register [LEVEL GAUGE] to a USER button. (l 82) This function displays the horizontal/vertical tilt of the unit with the electronic level. ∫ To correct the tilt (Horizontal direction) (Vertical direction)    When correcting the leftward tilt When correcting the downward tilt ≥ The horizontal tilt display A and vertical tilt display B appear yellow when there is a tilt, and appear green when there is almost no tilt.
PAGE 94
HC-X1_E_GC_DVQP1176ZA_eng.book 94 ページ２０１６年１１月２８日月曜日午前１１時４０分 [FLASH BAND] ≥ Register [FLASH BAND] to a USER button. (l 82) If you set this item to [ON], you can compensate for and reduce flash band, a phenomenon that creates markedly different levels of luminance between the top and bottom of the image when recording is performed in an environment where another camera is firing its flash. ≥ FBC appears on the screen.
PAGE 95
HC-X1_E_GC_DVQP1176ZA_eng.book 95 ページ２０１６年１１月２８日月曜日午前１１時４０分 [PRE-REC] ≥ Register [PRE-REC] to a USER button. (l 82) This allows the recording of an image and audio to start before you press the recording start/stop button. AVCHD scenes will be recorded from approximately 3 seconds before the operation, while MOV/MP4 will be recorded from approximately 4 seconds before the operation. ≥ [P-] is displayed on the screen. After you start recording, the display changes to [P-REC].
PAGE 96
HC-X1_E_GC_DVQP1176ZA_eng.book 96 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ To change the type of WFM Select the menu. MENU : [SW SETUP] # [WFM TYPE] # desired setting [WAVE]: Displays waveforms as waves. [VECTOR]: Displays waveforms as vectors. [WAVE/VECTOR]: Switches the setting each time the applicable USER button is pressed.
PAGE 97
HC-X1_E_GC_DVQP1176ZA_eng.book 97 ページ２０１６年１１月２８日月曜日午前１１時４０分 [A.IRIS LEVEL] ≥ Register [A.IRIS LEVEL] to a USER button. (l 82) This enables/disables the Auto Iris Level. ≥ When this item is enabled, the [AUTO IRIS LEVEL EFFECT] setting is applied. (l 68) [ZEBRA] ≥ Register [ZEBRA] to a USER button. (l 82) Press USER button or touch USER button icon in the recording screen. It will switch between the zebra display and the marker display every time the button is pressed.
PAGE 98
HC-X1_E_GC_DVQP1176ZA_eng.book 98 ページ２０１６年１１月２８日月曜日午前１１時４０分 [SCENE FILE] ≥ Register [SCENE FILE] to a USER button. (l 82) You can save the scene file settings to the SD card or load them from the SD card to this unit. ∫ Saving scene file settings 1 2 3 Press USER button or touch USER button icon in the recording screen. Touch [SAVE]. Touch the name of the scene file. ≥ All scene number settings ([F1:] to [F6:]) will be saved. ≥ Up to 8 files can be saved.
PAGE 99
HC-X1_E_GC_DVQP1176ZA_eng.book 4 99 ページ２０１６年１１月２８日月曜日午前１１時４０分 Press USER button or touch USER button icon in the recording screen. ≥ This will display and send a signal to the external device instructing it to start recording. ≥ To stop recording to the external device, press the applicable USER button or touch the applicable USER button icon again. This will display and send a signal to the external device instructing it to stop recording. [AF AREA] ≥ Register [AF AREA] to a USER button.
PAGE 100
HC-X1_E_GC_DVQP1176ZA_eng.book 100 ページ２０１６年１１月２８日月曜日午前１１時４０分 [VFR] This enables/disables Variable Frame Rate (VFR) Mode. In Variable Frame Rate Mode, you can record quick or slow motion picture by changing the frame rate before recording. Slow motion (overcrank recording) Used in scenes such as climaxes, a slow motion effect creates a dramatic impression. Set a frame rate that provides more frames than the frame rate in [REC FORMAT] does. Example: If you set [FHD 1080/25.
PAGE 101
HC-X1_E_GC_DVQP1176ZA_eng.book 101 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Frame rates and their effects Quick motion (undercrank) or slow motion (overcrank) recording is possible with the following frame rate settings: [REC FORMAT] Available frame rates [FHD 1080/29.97p 50M] 2 fps to 28 fps 30 fps 32 fps to 60 fps [FHD 1080/23.98p 50M] 2 fps to 22 fps 24 fps 26 fps to 60 fps [FHD 1080/25.
PAGE 102
HC-X1_E_GC_DVQP1176ZA_eng.book 102 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ It is not possible to adjust the shutter speed to a value slower than the limit imposed by the set frame rate. Example: When [REC FORMAT] is set to [FHD 1080/25.00p 50M], if you set the frame rate to 25 fps, the shutter speed cannot be adjusted to a value slower than 1/25. ≥ [BLACK FADE] and [WHITE FADE] are disabled.
PAGE 103
HC-X1_E_GC_DVQP1176ZA_eng.book 103 ページ２０１６年１１月２８日月曜日午前１１時４０分 [AWB] ≥ Register [AWB] to a USER button. (l 82) You can change the White Balance mode or use Auto White Balance or Auto Black Balance. (l 63, 66) [SUPER SLOW] This enables/disables Super Slow Recording. You can enable this function to record slow motion pictures. ≥ Register [SUPER SLOW] to a USER button. (l 82) ≥ Make the [REC MODE] and [REC FORMAT] settings.
PAGE 104
HC-X1_E_GC_DVQP1176ZA_eng.book 104 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ The following functions are canceled: j Flash band compensation (l 94, 166) j Relay recording (l 177) j Background recording (l 177) j Interval Recording (l 182) j PRE-REC (l 95, 183) j Hybrid Optical Image Stabilizer (l 50) j Area Mode (l 90) j Focus Transition (l 60) j Digital Zoom (l 87) j Infrared Recording mode (l 92, 183) j Custom AF function (l 54) j i.
PAGE 105
HC-X1_E_GC_DVQP1176ZA_eng.book 105 ページ２０１６年１１月２８日 [LOW GAIN] ≥ Register [LOW GAIN] to a USER button. (l 82) The gain value can be changed to low gain. (l 69) ≥ This item cannot be set during Freeze Frame. (l 89) [MID GAIN] ≥ Register [MID GAIN] to a USER button. (l 82) The gain value can be changed to middle gain. (l 69) ≥ This item cannot be set during Freeze Frame. (l 89) [HIGH GAIN] ≥ Register [HIGH GAIN] to a USER button. (l 82) The gain value can be changed to high gain.
PAGE 106
HC-X1_E_GC_DVQP1176ZA_eng.book 106 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Useful functions ャモンヴ  ュリヴヱバヮヰュユチヤラレワュチョリロヵユンヒバプフ  ヒバヒプ  ヒバフヰョョ A B C BARS button ND FILTER switch DISP/MODE CHK button Color Bar Screen BARS button Press the BARS button to output a color bar screen to an external monitor so you can adjust them. ≥ To cancel, press the BARS button again. ≥ It will be canceled when the unit is turned off.
PAGE 107
HC-X1_E_GC_DVQP1176ZA_eng.book 107 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ The test tone volume differs depending on the [TEST TONE] setting. (l 190) ≥ You can record color bars as motion pictures. ≥ If you press the BARS button while recording color bars as a motion picture, you can stop displaying the color bars. To display them again, stop the recording and press the BARS button. ND filter Using the ND filter switch, you can switch the built-in optical ND filter setting.
PAGE 108
HC-X1_E_GC_DVQP1176ZA_eng.book 108 ページ２０１６年１１月２８日月曜日午前１１時４０分 Switching the screen indications/mode information display DISP/MODE CHK button When the DISP/MODE CHK button is pressed, all screen displays disappear, except for the counter display, time stamp display*, zebra pattern display, marker display, and safety zone display. (l 203) * When [DATE/TIME] is set to [TIME], [DATE], or [DATE&TIME] ≥ To cancel the setting, press the DISP/MODE CHK button.
PAGE 109
HC-X1_E_GC_DVQP1176ZA_eng.book 109 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Using Operation Icons You can use convenient functions just by the easy operation of touching the screen. 1 Touch the LCD monitor in the recording screen. ≥ The operation icons are displayed. 2 PRE-REC Touch an operation icon. ATW.L ≥ The following function is available. Refer to the respective pages for the operation. F1: , F2: etc. DRS , PRE-REC etc.
PAGE 110
HC-X1_E_GC_DVQP1176ZA_eng.book 110 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Using of jog dial A Jog dial  ヴユロバヱヶヴラヴユヵ Selecting/setting items You can select and set menu items (l 40), etc. using the jog dial. 1 Rotate the jog dial on the menu screen, etc., to move the cursor. ≥ The selected item will be displayed in yellow. 2 Push the jog dial to set. Menu operations for setting a value When a menu that lets you set a value is displayed, select the value display before adjusting the setting.
PAGE 111
HC-X1_E_GC_DVQP1176ZA_eng.book 111 ページ２０１６年１１月２８日月曜日午前１１時４０分 Using the multi manual function You can select the following functions and adjust their settings using the jog dial. You can also switch between the functions and adjust their settings. (When the recording screen is displayed) On-screen icons Functions Settings GAIN Gain adjustment (l 69) Adjusts the gain value. VAR VAR adjustment (l 66) Adjusts the VAR setting of the White Balance.
PAGE 112
HC-X1_E_GC_DVQP1176ZA_eng.book 112 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ Change settings as follows: Functions Settings to be changed in advance Gain adjustment Switch to Manual Mode. (l 44) VAR adjustment Press the WHITE BAL button and the USER button to which [AWB] is registered to set the White Balance mode to [VAR]. (l 63) AF Area Width adjustment Press the USER button to which [AF AREA] is registered to enable AF Area Setting Adjustment or set [AF AREA WIDTH] to [SET] using the menu.
PAGE 113
HC-X1_E_GC_DVQP1176ZA_eng.book 113 ページ２０１６年１１月２８日月曜日午前１１時４０分 Playback Motion picture/Still picture playback 1 2 Set this unit to playback mode. (l 31)   Touch the play mode select icon A. 10 11 12 UHD UHD 13 14 15 UHD UHD UHD 16 17 18 UHD UHD UHD UHD Media display The selected media is displayed in yellow. 3 Select the media C you wish to play back.
PAGE 114
HC-X1_E_GC_DVQP1176ZA_eng.book 114 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ (If you have touched the recording mode option [AVCHD]) After you have touched a recording format option, one of the following icons will be displayed on each thumbnail. j PS : Scenes recorded in [PS 1080/59.94p]/[PS 1080/50.00p] j PH : Scenes recorded in [PH 1080/59.94i]/[PH 1080/23.98p]/[PH 1080/50.00i] j HA : Scenes recorded in [HA 1080/59.94i]/[HA 1080/50.00i] j HE : Scenes recorded in [HE 1080/59.94i]/[HE 1080/50.
PAGE 115
HC-X1_E_GC_DVQP1176ZA_eng.book 115 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Change the thumbnail display While the thumbnail is displayed, the thumbnail display changes in the following order if the zoom lever or the sub zoom lever is operated to side or side. T T W ( side) ( W side) 20 scenes () 9 scenes () 1 scene () Scene information display* * Detailed information of the scene is displayed when playing back motion pictures. Following information is displayed.
PAGE 116
HC-X1_E_GC_DVQP1176ZA_eng.book 1 2 116 ページ２０１６年１１月２８日月曜日午前１１時４０分 Push the jog dial while [ VOLUME] is displayed. Rotate the jog dial to adjust the volume. C [VOLUME]  3 Push the jog dial to finish the adjustment. ≥ Sound will be heard only during normal motion picture playback. ≥ If pause play is continued for 5 minutes, the screen returns to the thumbnails.
PAGE 117
HC-X1_E_GC_DVQP1176ZA_eng.book 117 ページ２０１６年１１月２８日月曜日午前１１時４０分 Motion picture playback using operation icon For details on the basic playback operations, refer to page 113. Playback operation Playback display Operating steps During Playback Touch the LCD monitor and slide from right to left (from left to right) during playback.
PAGE 118
HC-X1_E_GC_DVQP1176ZA_eng.book 118 ページ２０１６年１１月２８日月曜日午前１１時４０分 Playback Useful functions Creating still picture from motion picture You can save a frame of a recorded motion picture as a still picture. The picture size with which a still picture will be recorded differs depending on the picture size of [REC FORMAT] with which the motion picture was recorded. Recording format Aspect ratio Picture size 17:9 8.
PAGE 119
HC-X1_E_GC_DVQP1176ZA_eng.book 119 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ Maximum number of recordable pictures that can be displayed is 9999. If the number of recordable pictures exceeds 9999, R 9999+ is displayed. The number will not change when the picture is taken until the number of recordable pictures is 9999 or less. ≥ When playing back a still picture recorded with this unit in the 17:9 aspect, black bands appear on the top and bottom of the screen.
PAGE 120
HC-X1_E_GC_DVQP1176ZA_eng.book 2 120 ページ２０１６年１１月２８日月曜日午前１１時４０分 Touch the playback date. ≥ The scenes or still pictures recorded on the date selected are displayed as thumbnails. 3 Touch the scenes or still picture to be played back. ≥ Dates cannot be selected while the thumbnail screen for the recording format [ALL] of the recording mode [MOV]/[MP4] is displayed.
PAGE 121
HC-X1_E_GC_DVQP1176ZA_eng.book 121 ページ２０１６年１１月２８日月曜日午前１１時４０分 Editing Deleting scenes/still pictures Deleted scenes/still pictures cannot be restored, so perform appropriate confirmation of the contents before proceeding with deletion. ≥ Press the THUMBNAIL button to switch this unit to the Playback Mode. (l 31) ∫ To delete the scene or still picture being played back Touch while scenes or still pictures to be deleted are being played back.
PAGE 122
HC-X1_E_GC_DVQP1176ZA_eng.book 122 ページ２０１６年１１月２８日月曜日午前１１時４０分 When you stop deleting halfway: Touch [CANCEL] or press MENU button while deleting. ≥ The scenes or still pictures that have already been deleted when the deletion is canceled cannot be restored. To complete editing: Touch [Return] or press MENU button.
PAGE 123
HC-X1_E_GC_DVQP1176ZA_eng.book 123 ページ２０１６年１１月２８日月曜日午前１１時４０分 Editing Copying between SD cards Motion pictures or still pictures recorded with this unit can be copied between SD Cards inserted in this unit. ≥ Copying is not possible if the type of the source SD card (SDHC Memory Card/SDXC Memory Card) is different from that of the target SD card. ∫ Check the used space of the copy destination It is possible to check the used space of the SD Card by [MEDIA STATUS].
PAGE 124
HC-X1_E_GC_DVQP1176ZA_eng.book 124 ページ２０１６年１１月２８日月曜日午前１１時４０分 If you will delete the motion pictures or still pictures after copying is complete, be sure to play back the motion pictures or still pictures to check that they have been copied to correctly before deleting. ≥ Depending on the following conditions, the time it takes for copying may be longer. j The number of recorded scenes is large.
PAGE 125
HC-X1_E_GC_DVQP1176ZA_eng.book 125 ページ２０１６年１１月２８日月曜日午前１１時４０分 Linking to external devices Connecting Headphones, a Remote Control or an External Monitor Headphones You can connect headphones (commercially-available) to the headphone output jack (3.5 mm diameter stereo mini jack).  A Headphone output jack ≥ Sound is not output from the speaker when headphones are connected.
PAGE 126
HC-X1_E_GC_DVQP1176ZA_eng.book 126 ページ２０１６年１１月２８日月曜日午前１１時４０分 External monitor You can connect this unit to an external monitor as shown in the figure below.
PAGE 127
HC-X1_E_GC_DVQP1176ZA_eng.book 127 ページ２０１６年１１月２８日月曜日午前１１時４０分 When connecting with an HDMI cable using an HDMI-to-DVI converter, etc., be sure to connect the HDMI cable to the connector of this unit last. Connecting the HDMI cable to the connector of this unit first may result in malfunction. ≥ This unit is not compatible with the VIERA Link. ≥ Use a commercially-available High Speed HDMI cable. If possible, we recommend using a cable with a length of 3 m or less.
PAGE 128
HC-X1_E_GC_DVQP1176ZA_eng.book 128 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ This item is set to [OFF] in the following situations when this unit is in Recording Mode: j When [REC FORMAT] is set to a setting with a size of 4K (4096k2160) or UHD (3840k2160) (l 161) j During auto recording (l 98, 188) Setting the external output resolution Change the setting for outputting images to an external monitor or other external device (recorder, etc.). Select the [RESOLUTION] menu.
PAGE 129
HC-X1_E_GC_DVQP1176ZA_eng.book 129 ページ２０１６年１１月２８日月曜日午前１１時４０分 About external output resolutions The external output resolution varies depending on the [RESOLUTION] setting and connected terminal. ≥ When [RESOLUTION] is set to [SYSTEM], the external output resolution varies depending on the picture size and frame rate in [REC FORMAT]. (When [SYSTEM FREQ] is set to [59.94Hz]) Setting Picture size/Frame rate in [REC FORMAT] 4K (4096k2160)/ 24.00p UHD (3840k2160)/ 59.94p UHD (3840k2160)/ 29.
PAGE 130
HC-X1_E_GC_DVQP1176ZA_eng.book 130 ページ２０１６年１１月２８日 Setting Picture size/Frame rate in [REC FORMAT] FHD (1920k1080)/ 23.98p, PH 1080/23.98p PM 720 (1280k720)/ 59.94p SA 480 (720k480)/ 59.94i 月曜日午前１１時４０分 External output resolution [RESOLUTION] setting HDMI OUT terminal VIDEO OUT terminal [SYSTEM] 1080/23.98p [1080p] 1080/59.94p [1080i] 1080/59.94i [DOWN CONV.] 480/59.94p [SYSTEM] 720/59.94p [1080p] 1080/59.94p [1080i] 1080/59.94i [DOWN CONV.] 480/59.94p 480/59.94i [SYSTEM] 480/59.
PAGE 131
HC-X1_E_GC_DVQP1176ZA_eng.book 131 ページ２０１６年１１月２８日 Setting Picture size/Frame rate in [REC FORMAT] FHD (1920k1080)/ 25.00p PM 720 (1280k720)/ 50.00p SA 576 (720k576)/ 50.00i 月曜日午前１１時４０分 External output resolution [RESOLUTION] setting HDMI OUT terminal VIDEO OUT terminal [SYSTEM] 1080/25.00p [1080p] 1080/50.00p [1080i] 1080/50.00i [DOWN CONV.] 576/50.00p [SYSTEM] 720/50.00p [1080p] 1080/50.00p [1080i] 1080/50.00i [DOWN CONV.] 576/50.00p 576/50.00i [SYSTEM] 576/50.00p 576/50.
PAGE 132
HC-X1_E_GC_DVQP1176ZA_eng.book 132 ページ２０１６年１１月２８日月曜日午前１１時４０分 Linking to external devices Connecting to a PC (File transfer/nonlinear editing) When this device and a computer for editing are connected using a USB 3.0 Cable (commerciallyavailable), image data in the SD card can be transferred. ≥ This unit supports USB 3.0. ≥ Concerning non-linear editing, refer to the instruction manual of your editing software. ≥ Final Cut Pro can be used if you have a Mac computer.
PAGE 133
HC-X1_E_GC_DVQP1176ZA_eng.book 133 ページ２０１６年１１月２８日月曜日午前１１時４０分 Connecting to a PC Micro-B USB DEVICE A USB 3.0 Cable (commercially-available) ≥ Insert the plugs as far as they will go. 1 Connect this unit to the AC adaptor. ≥ Use the AC adaptor to free you from worrying about the battery running down. 2 3 Turn on the unit. Set [USB MODE SELECT] to [DEVICE]. MENU 4 Set [USB MODE] to [ON].
PAGE 134
HC-X1_E_GC_DVQP1176ZA_eng.book 134 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ To disconnect USB Cable safely (For Windows) Select the icon in task tray displayed on the PC, and then select the model number of this unit to disconnect the USB cable. ≥ Depending on your PC’s settings, this icon may not be displayed. (For Mac) Drag [CAM_SD] disk icon to the [Trash], and then disconnect the USB Cable.
PAGE 135
HC-X1_E_GC_DVQP1176ZA_eng.book 135 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Folder names for motion picture data recorded in MOV/MP4 format The fourth to eighth characters of the folder name of a recorded MOV/MP4 scene are determined by its picture size, frame rate, motion picture format, recording setting and camera number setting.
PAGE 136
HC-X1_E_GC_DVQP1176ZA_eng.book 136 ページ２０１６年１１月２８日月曜日午前１１時４０分 Linking to external devices Copying/playing back with an external media device ≥ In these Operating Instructions, “USB hard disk drive” is indicated as “USB HDD”. If you connect an external media device, such as USB HDD or USB flash memory (commerciallyavailable) to this unit, you can copy motion pictures and still pictures recorded on this unit to an external media device.
PAGE 137
HC-X1_E_GC_DVQP1176ZA_eng.book 1 137 ページ２０１６年１１月２８日月曜日午前１１時４０分 (When using USB HDD) Connect the AC adaptor (supplied with USB HDD) to the USB HDD. ≥ If you are using a bus-powered or portable USB HDD, this unit can supply power to the USB HDD by USB Cable (supplied with USB HDD). 2 Connect the AC adaptor to this unit. ≥ Use the AC adaptor to free you from worrying about the battery running down. 3 4 Turn on this unit, and press the THUMBNAIL button to switch to Playback Mode.
PAGE 138
HC-X1_E_GC_DVQP1176ZA_eng.book 138 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Points to check before copying ≥ When using an external media device for the first time, or using an external media device that has been used with other devices, first run [FORMAT MEDIA]. ≥ Before copying, go to [MEDIA STATUS] to check the amount of free space on the external media device. (l 138) ≥ It may take longer to copy when there are many scenes.
PAGE 139
HC-X1_E_GC_DVQP1176ZA_eng.book 139 ページ２０１６年１１月２８日月曜日午前１１時４０分 Copy once 1 2 Connect this unit to the external media device to prepare for copying. (l 136) Touch [DIFFERENTIAL COPY]. ≥ You can also access this function by selecting menu items. [COPY] # [DIFFERENTIAL COPY] 3 4 5 Touch the media you want to copy. Touch [YES]. Touch [EXIT] when the copy complete message is displayed. ≥ The thumbnail view of the copy destination is indicated.
PAGE 140
HC-X1_E_GC_DVQP1176ZA_eng.book 140 ページ２０１６年１１月２８日月曜日午前１１時４０分 Playing back the External Media ≥ Only motion picture/still picture that have been copied by connecting this unit to the external media device can be played back.  USB HOST A B C 1 USB Cable (supplied with USB HDD) USB HDD (commercially-available) USB flash memory (commercially-available) Connect this unit to the external media device to prepare for playback.
PAGE 141
HC-X1_E_GC_DVQP1176ZA_eng.book 141 ページ２０１６年１１月２８日月曜日午前１１時４０分 Linking to external devices Using an iPad as a Remote Control (AG ROP application) Attaching a wireless module that support this unit (l 142) to the USB HOST terminal of this unit allows you to connect to a wireless LAN network. You can remotely control some functions by connecting this unit and an iPad on which the AG ROP application is installed.
PAGE 142
HC-X1_E_GC_DVQP1176ZA_eng.book 142 ページ２０１６年１１月２８日月曜日午前１１時４０分 Before connection iPad/AG ROP application Install the AG ROP application on the iPad. ≥ Download the AG ROP application from the App Store. ≥ Supported OS for the AG ROP application: iOS 7.1 or later (as of November 2016) Wireless module Attach a wireless module that support this unit (AJ-WM50, AJ-WM30: optional*1) to the USB HOST terminal of this unit. *1 It may not be available in some countries.
PAGE 143
HC-X1_E_GC_DVQP1176ZA_eng.book 143 ページ２０１６年１１月２８日月曜日午前１１時４０分 (AJ-WM30) Model number Compatible countries and regions AJ-WM30MC People’s Republic of China AJ-WM30P United States, Canada, Mexico, Argentina, Peru, Taiwan AJ-WM30E EU countries, EFTA countries, Australia, New Zealand, Russia, Ukraine, Saudi Arabia, United Arab Emirates, Kuwait, Oman, Egypt, Republic of South Africa, South Korea, Philippines, Malaysia, Singapore AJ-WM30 Japan ≥ Outdoor use is prohibited in France.
PAGE 144
HC-X1_E_GC_DVQP1176ZA_eng.book 144 ページ２０１６年１１月２８日月曜日午前１１時４０分 Entering text Operate in the same way as you enter characters with a keyboard. Icon Description of operation [A-a] Switches between uppercase and lowercase. [Return] [ ] [ ] [BS] / [Enter] 6 Returns to the previous screen. The entered characters are canceled. Switches to symbols and numbers. Enters a space. Deletes a character. Deletes the previous character if the cursor is in an empty space. Moves the cursor to left or right.
PAGE 145
HC-X1_E_GC_DVQP1176ZA_eng.book 145 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Configuring the wireless LAN settings (IP address, etc.) 1 Select the menu. MENU 2 : [NETWORK SETUP] # [Wireless LAN setup] Touch and set the desired items as needed. ≥ All default settings are indicated with underlined text. [IP Address]: Enter the IP address. ≥ The default setting is [192.168.0.1]. [Subnet Mask]: Enter the subnet mask. ≥ The default setting is [255.255.255.0]. [Gateway]: Enter the gateway.
PAGE 146
HC-X1_E_GC_DVQP1176ZA_eng.book 146 ページ２０１６年１１月２８日月曜日午前１１時４０分 Connecting this unit and an iPad ≥ Change the mode to Recording Mode. (l 31) If you switch to Recording Mode while this unit is connected in Playback Mode, the connection may be terminated to restart this unit. We recommend setting this unit to Recording Mode before making a connection. ∫ Settings to be made on the iPad For information on the settings to be made on the iPad, refer to [CONNECTION] in Help of the AG ROP app.
PAGE 147
HC-X1_E_GC_DVQP1176ZA_eng.book 147 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ When [DIRECT] is selected, [SECURITY TYPE] is fixed to [WPA2-AES]. ≥ Some settings in [BAND], [CHANNEL (2.4GHz)] and [CHANNEL (5GHz)] cannot be selected depending on the wireless module used. ≥ For details on how to enter characters, refer to page 144. 3 4 Touch [RETURN]. Set [DHCP] to [SERVER]. MENU 5 6 7 8 : [NETWORK SETUP] # [Wireless LAN setup] # [DHCP] # [SERVER] Touch [EXIT].
PAGE 148
HC-X1_E_GC_DVQP1176ZA_eng.book 148 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ [SSID(SELECT)] is available only when [USB MODE] is set to [ON], [USB MODE SELECT] is set to [HOST] and a wireless module that supports this unit is attached. ≥ Depending on your environment, the communication speed may become slower or the wireless access point may not be available for use. ≥ When [DHCP] in [Wireless LAN setup] is set to [OFF] or [CLIENT], apply the [IP Address] setting to [AG ROP] in [Settings] (l 145) on the iPad.
PAGE 149
HC-X1_E_GC_DVQP1176ZA_eng.book 149 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Connecting from History Connections made to wireless access points are saved in History. Connecting from History allows you to easily connect with the same settings as used previously. ≥ Attach a wireless module that support this unit to the USB HOST terminal of this unit. (l 142) ≥ Set [USB MODE SELECT] to [HOST]. (l 197) ≥ Set [USB MODE] to [ON]. (l 197) 1 Select the menu.
PAGE 150
HC-X1_E_GC_DVQP1176ZA_eng.book 150 ページ２０１６年１１月２８日月曜日午前１１時４０分 Operations during AG ROP application connection ∫ Operations with this unit during connection ≥ The following buttons are disabled: j SHUTTER button j GAIN button j WHITE BAL button j MENU button (The applicable USER button is also disabled, making it impossible to operate the menu.
PAGE 151
HC-X1_E_GC_DVQP1176ZA_eng.book 151 ページ２０１６年１１月２８日月曜日午前１１時４０分 Menu Using the Menu Refer to page 40 for how to set up the Menu. Scene file Settings that are assigned to [F1:] in [FILE SELECT] by default are indicated with underlined text. MENU : [SCENE FILE] # desired setting [FILE SELECT] You can save the desired image settings to each scene number. Switch the scene number in accordance with the recording conditions.
PAGE 152
HC-X1_E_GC_DVQP1176ZA_eng.book 152 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ This function’s default setting is [F1:]. ≥ It is possible to switch the scene number by touching F1: to F6: while displaying the operation icons. (l 109) ≥ You can rename the titles for scene numbers (FLUO, etc.) in [NAME EDIT]. ≥ It will return to the default settings when [SCENE] is selected in [INITIAL SET]. (l 198) [NAME EDIT] You can rename the title of the scene number selected in [FILE SELECT]. 1 2 Touch [NAME EDIT].
PAGE 153
HC-X1_E_GC_DVQP1176ZA_eng.book 153 ページ２０１６年１１月２８日月曜日午前１１時４０分 [MASTER DETAIL] Adjusts the degree of overall outline correction in images. 1 2 Touch [MASTER DETAIL]. Touch / to adjust settings. ≥ You can select a value between s31 and r31. 3 Touch [EXIT] to exit the menu screen. ≥ The default setting that is assigned to [F1:] in [FILE SELECT] is “0”. [DETAIL CORING] Adjusts the detail noise removal level. 1 2 Touch [DETAIL CORING]. Touch / to adjust settings.
PAGE 154
HC-X1_E_GC_DVQP1176ZA_eng.book 154 ページ２０１６年１１月２８日月曜日午前１１時４０分 [RB GAIN CONTROL SETTING] This adjusts the color balance for [Ach] or [Bch] of the White Balance mode. You can also set whether or not to apply the color balance settings to Auto White Balance/Auto Black Balance. 1 Touch [RB GAIN CONTROL SETTING], and select the desired item. [AWB A]: Setting for the White Balance mode [Ach] [AWB B]: Setting for the White Balance mode [Bch] 2 Touch the desired setting item.
PAGE 155
HC-X1_E_GC_DVQP1176ZA_eng.book 155 ページ２０１６年１１月２８日月曜日午前１１時４０分 [CHROMA LEVEL] Adjusts color density. 1 2 Touch [CHROMA LEVEL]. Touch / to adjust settings. ≥ You can select a value between s70 and r30. 3 Touch [EXIT] to exit the menu screen. ≥ The default setting that is assigned to [F1:] in [FILE SELECT] is “0”. [CHROMA PHASE] Adjusts color balance. 1 2 Touch [CHROMA PHASE]. Touch / to adjust settings. ≥ You can select a value between s31 and r31. 3 Touch [EXIT] to exit the menu screen.
PAGE 156
HC-X1_E_GC_DVQP1176ZA_eng.book 156 ページ２０１６年１１月２８日月曜日午前１１時４０分 [COLOR CORRECTION SETTING] This function sets color saturation and phase. It applies individual effect on 16 phases in an image. It can be set to individual color hue. R-Mg R 90° 112.5° Mg 67.5° YI-R-R Mg-Mg-B 135° 45° YI-YI-R Mg-B-B 157.5° 22.5°  Yl 0° 180° B  202.5° 337.5° B-B-Cy G-YI-YI 225° A 315° B-Cy-Cy G-G-YI 247.5° G B 292.
PAGE 157
HC-X1_E_GC_DVQP1176ZA_eng.book 157 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ By default the following values are set for [F1:] in [FILE SELECT] j SAT: “0” j PHASE: “0” [MASTER PED] Adjustment of black level based on the image is performed. 1 2 Touch [MASTER PED]. Touch / to adjust the black level. ≥ You can select a value between s150 and r150. 3 Touch [EXIT] to exit the menu screen. ≥ The default setting that is assigned to [F1:] in [FILE SELECT] is “0”.
PAGE 158
HC-X1_E_GC_DVQP1176ZA_eng.book 158 ページ２０１６年１１月２８日月曜日午前１１時４０分 [KNEE MODE] To avoid overexposure, select the compression level of the high intensity video signals received through the image sensor. 1 2 Touch [KNEE MODE]. Touch / to select the setting item. [AUTO]: Sets the level automatically according to the signals received. [MANUAL]: Applies the [KNEE MASTER POINT] and [KNEE MASTER SLOPE] settings. [OFF]: Disables the Knee function. 3 Touch [EXIT] to exit the menu screen.
PAGE 159
HC-X1_E_GC_DVQP1176ZA_eng.book 159 ページ２０１６年１１月２８日月曜日午前１１時４０分 [DRS EFFECT] Selects the level of the DRS function. 1 2 Touch [DRS EFFECT]. Touch / to select the setting item. [1]/[2]/[3] ≥ Higher the value, greater the compression level of the highly illuminated area. ≥ Higher the value, greater the noise of the dark area. 3 Touch [EXIT] to exit the menu screen.
PAGE 160
HC-X1_E_GC_DVQP1176ZA_eng.book 160 ページ２０１６年１１月２８日月曜日午前１１時４０分 System mode All default settings are indicated with underlined text. MENU : [SYSTEM MODE] # desired setting [SYSTEM FREQ] Set the system frequency of this unit. [59.94Hz]: System frequency for regions where the TV broadcasting system is NTSC [50.00Hz]: System frequency for regions where the TV broadcasting system is PAL ≥ After you have changed the system frequency, this unit will be restarted automatically.
PAGE 161
HC-X1_E_GC_DVQP1176ZA_eng.book 161 ページ２０１６年１１月２８日月曜日午前１１時４０分 [REC FORMAT] Switch the picture quality of motion pictures to be recorded with this unit. Depending on the settings of [SYSTEM FREQ] (l 160) and [REC MODE], the available [REC FORMAT] settings differ. How to read a [REC FORMAT] setting Items that make up a [REC FORMAT] setting represent Size, Vertical resolution, Frame rate, and Bit rate.
PAGE 162
HC-X1_E_GC_DVQP1176ZA_eng.book 162 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ When [MOV] or [MP4] in [REC MODE] is selected System frequency Size Frame rate setting (Picture size) Recording format [59.94Hz]/ [50.00Hz] [4K 2160/24.00p 100M] 4K (4096k2160) [UHD 2160/59.94p 150M] UHD (3840k2160) [UHD 2160/29.97p 100M] [UHD 2160/23.98p 100M] [FHD 1080/59.94p 24.00p Average 100 Mbps 59.94p Average 150 Mbps 29.97p 23.98p ] [59.94Hz] [FHD 1080/29.97p ] [FHD 1080/23.98p ] FHD (1920k1080) 23.98p 29.
PAGE 163
HC-X1_E_GC_DVQP1176ZA_eng.book Recording format 163 ページ２０１６年１１月２８日 System frequency setting Picture size [PS 1080/50.00p] [HA 1080/50.00i] [50.00Hz] [HE 1080/50.00i] 午前１１時４０分 Frame rate Bit rate (VBR) 50.00p Average 25 Mbps 1920k1080 [PH 1080/50.00i] 月曜日 Average 21 Mbps 50.00i Average 17 Mbps 1440k1080 Average 5 Mbps [PM 720/50.00p] 1280k720 50.00p Average 8 Mbps [SA 576/50.00i] 720k576 50.
PAGE 164
HC-X1_E_GC_DVQP1176ZA_eng.book 164 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording function Normal recording Interval Rec (l 182) Super Slow Recording (l 103, 183), VFR Mode (l 100, 183) [UHD 2160/ 25.00p 100M] ± ± s ± s ± [UHD 2160/ 23.98p 100M] ± s s ± s ± [FHD 1080/ 59.94p ] ± s s ± s ± [FHD 1080/ 50.00p ] ± s s ± s ± [FHD 1080/ 29.97p ] ± s s ± s ± [FHD 1080/ 25.00p ] ± s s ± s ± [FHD 1080/ 23.98p ] ± s s ± s ± [FHD 1080/ 59.
PAGE 165
HC-X1_E_GC_DVQP1176ZA_eng.book 165 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording function Normal recording Interval Rec (l 182) Super Slow Recording (l 103, 183), VFR Mode (l 100, 183) [PH 1080/ 23.98p] ± s s ± ± s [HA 1080/ 59.94i] ± ± s ± ± s [HA 1080/ 50.00i] ± ± s ± ± s [HE 1080/ 59.94i] ± s s ± ± s [HE 1080/ 50.00i] ± s s ± ± s [PM 720/ 59.94p] ± s s ± ± s [PM 720/ 50.00p] ± s s ± ± s [SA 480/ 59.94i] ± s s ± ± s [SA 576/ 50.
PAGE 166
HC-X1_E_GC_DVQP1176ZA_eng.book 166 ページ２０１６年１１月２８日月曜日午前１１時４０分 [HIGH SENS. MODE] This sets the optimal recording mode for the recording environment. [NORMAL]: Select this setting when the light level of the recording environment is normal. [HIGH SENS.]: Select this setting when recording in a dark environment. ≥ [H.SENS] is displayed on the screen when [HIGH SENS.] is selected.
PAGE 167
HC-X1_E_GC_DVQP1176ZA_eng.book 167 ページ２０１６年１１月２８日月曜日午前１１時４０分 User switch All default settings are indicated with underlined text. MENU : [USER SW] # desired setting [USER1]/[USER2]/[USER3]/[USER4]/ [USER5]/[USER6]/[USER7]/[USER8]/[USER9] Sets the function to assign to the USER buttons. (l 82) ≥ For the functions of the USER button that can be registered, refer to page 84.
PAGE 168
HC-X1_E_GC_DVQP1176ZA_eng.book 168 ページ２０１６年１１月２８日月曜日午前１１時４０分 Switch setting All default settings are indicated with underlined text. MENU : [SW SETUP] # desired setting [IRIS RING] Sets the rotation direction and iris control of the iris ring. A [DOWN OPEN]: Iris will open when it is turned toward B. [UP OPEN]: Iris will open when it is turned toward A. B 1 Iris ring  [LOW GAIN] Sets the gain value to be used when you switch to [LOW GAIN] by pressing the GAIN button.
PAGE 169
HC-X1_E_GC_DVQP1176ZA_eng.book 169 ページ２０１６年１１月２８日月曜日午前１１時４０分 [HIGH GAIN] Sets the gain value to be used when you switch to [HIGH GAIN] by pressing the GAIN button. 1 2 Touch [HIGH GAIN]. Touch / to adjust settings. ≥ You can select [AUTO] or a value between 0 dB and 24 dB. When [EXTENDED SENSITIVITY] is set to [ON], you can set a value between -3 dB and 24 dB. (l 165) 3 Touch [EXIT] to exit the menu screen. ≥ This function’s default setting is “12 dB”.
PAGE 170
HC-X1_E_GC_DVQP1176ZA_eng.book 170 ページ２０１６年１１月２８日月曜日午前１１時４０分 [BLUR AMPLITUDE] This sets the blur amplitude of the Image Stabilizer during recording. (l 50) [1]/[2]/[3]/[4]/[5] [BLUR FREQUENCY] This sets the blur frequency of the Image Stabilizer. (l 50) [1]/[2]/[3] [ATW SET] When you press the WHITE BAL button, you can assign ATW. [OFF]: Does not assign ATW when the WHITE BAL button is pressed. [Ach]: Sets the White Balance mode to ATW when the WHITE BAL button is pressed to switch to [Ach].
PAGE 171
HC-X1_E_GC_DVQP1176ZA_eng.book 171 ページ２０１６年１１月２８日月曜日午前１１時４０分 [WB VAR] Sets the color temperature when the White Balance mode is set to [VAR]. (l 66) 1 2 Touch [WB VAR]. Touch / to adjust settings. ≥ You can select a value between 2000K and 15000K. 3 Touch [EXIT] to exit the menu screen. ≥ This function’s default setting is “3200K”. [MF ASSIST] When [ON] is selected, focus is automatically adjusted after you adjust it with the focus ring in Manual Focus Mode.
PAGE 172
HC-X1_E_GC_DVQP1176ZA_eng.book 172 ページ２０１６年１１月２８日月曜日午前１１時４０分 [FOCUS RING DRIVE] This sets the way you adjust focus with the focus ring. (l 53) [SPEED]/[COARSE]/[FINE] [FOCUS MACRO] This enables/disables the Focus Macro function. [ON]/[OFF] ≥ If [ON] is selected, subjects at a distance of approximately 10 cm to infinity can be brought into focus when the zoom position is at the W end. (l 48) [AREA MODE] You can set an Area Mode effect.
PAGE 173
HC-X1_E_GC_DVQP1176ZA_eng.book 173 ページ２０１６年１１月２８日月曜日午前１１時４０分 [WFM] This enables/disables the Wave Form Monitor function. (l 95) [ON]/[OFF] [WFM TYPE] This sets the type of Wave Form Monitor. (l 96) [WAVE]/[VECTOR]/[WAVE/VECTOR] [WFM POSITION] This sets the display positions of Wave Form Monitor. (l 96) [TOP/LEFT]/[TOP/RIGHT]/[BOTTOM/LEFT]/[BOTTOM/RIGHT] [ZEBRA] Switch between the zebra display and marker display.
PAGE 174
HC-X1_E_GC_DVQP1176ZA_eng.book 174 ページ２０１６年１１月２８日月曜日午前１１時４０分 [SUB REC BUTTON] Enable/disable of the sub recording start/stop button on the handle can be switched. [INHIBIT]/[ACTIVE] [FAST ZOOM] When [ON] is selected, you can use Fast Zoom when operating the zoom with the zoom lever. (l 49) [ON]/[OFF] [SUB ZOOM] Enable/disable of the sub zoom lever on the handle can be switched. Zoom speed will be different depending on the setting.
PAGE 175
HC-X1_E_GC_DVQP1176ZA_eng.book 175 ページ２０１６年１１月２８日 Auto switch setting All default settings are indicated with underlined text. MENU : [AUTO SW] # desired setting [A.IRIS] This enables/disables Auto Iris for Auto Iris Mode. (l 44) [ON]/[OFF] [AGC] This enables/disables AGC for Auto Iris Mode. (l 44) [ON]/[OFF] [AGC LIMIT] Sets the maximum possible gain value for Auto Gain Mode.
PAGE 176
HC-X1_E_GC_DVQP1176ZA_eng.book 176 ページ２０１６年１１月２８日月曜日午前１１時４０分 [AUTO SLOW SHTR] You can record bright pictures even in dark places by slowing the shutter speed. Slow Shutter works in Auto Shutter Mode. (l 71) [ON]/[OFF] ≥ The shutter speed will be adjusted to one of the following values according to the ambient brightness. The value will differ depending on the frame rate of the [REC FORMAT]. Frame rates Shutter speed 59.94p/59.94i/29.97p 1/30 or more 50.00p/50.00i/25.00p 1/25 or more 23.98p/24.
PAGE 177
HC-X1_E_GC_DVQP1176ZA_eng.book 177 ページ２０１６年１１月２８日月曜日午前１１時４０分 Recording Setup All default settings are indicated with underlined text. MENU : [RECORD SETUP] # desired setting [MEDIA SELECT] Card slot can be selected separately to record motion pictures. (l 41) [SD CARD 1]/[SD CARD 2] [2 SLOTS FUNC.] You can set relay/simultaneous/background/dual codec recording. ≥ Insert SD cards to card slot 1 and card slot 2. [OFF]: Cancel the setting.
PAGE 178
HC-X1_E_GC_DVQP1176ZA_eng.book 178 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Relay recording This is simple Relay Recording. It is possible to continuously record on the SD card in the other card slot even when the available capacity of the SD card runs out during the recording.         1 2 3 4   Slot 1 Slot 2 Recording is started Recording is paused A B C Recording The card slot used for recording is switched automatically. Replace the SD card with a recordable one.
PAGE 179
HC-X1_E_GC_DVQP1176ZA_eng.book 179 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Background recording You can continue recording a motion picture by recording it on the SD card that is not set as a recording destination in [MEDIA SELECT] (l 41).            5 6    1 2 3 4  Slot 1 Slot 2 Press the recording start/stop button. Press and hold the USER button to which [BACKGROUND] is registered.
PAGE 180
HC-X1_E_GC_DVQP1176ZA_eng.book 180 ページ２０１６年１１月２８日月曜日午前１１時４０分 ∫ Dual codec recording You can make main and sub recordings in separate [REC FORMAT] settings. Sub recording records scenes in a picture quality lower than that of the [REC FORMAT] setting for main recording.
PAGE 181
HC-X1_E_GC_DVQP1176ZA_eng.book 181 ページ２０１６年１１月２８日月曜日午前１１時４０分 [DUAL CODEC REC] This sets the sub recording scene settings for dual codec recording. ≥ For information on dual codec recording, refer to page 180. ≥ Select a [REC FORMAT] setting that supports dual codec recording. (See below.) [FHD 50Mbps]: Performs recording at a bit rate of 50Mbps. Scenes can be saved in either MOV or MP4 format. [FHD 8Mbps]: Performs recording at a bit rate of 8Mbps. Scenes can be saved in MOV format.
PAGE 182
HC-X1_E_GC_DVQP1176ZA_eng.book 182 ページ２０１６年１１月２８日月曜日午前１１時４０分 [INTERVAL REC] A scene that moves slowly for long period of time is recorded frame by frame with an interval, and is recorded as a short time motion picture. One frame is recorded every recording interval that is set. ≥ The number of frames per second differs depending on the frame rate of [REC FORMAT]. j 59.94i or 29.97p: 30 frames make up a scene of 1 second j 50.00i or 25.00p: 25 frames make up a scene of 1 second j 24.
PAGE 183
HC-X1_E_GC_DVQP1176ZA_eng.book 183 ページ２０１６年１１月２８日月曜日午前１１時４０分 [VFR MODE] This enables/disables Variable Frame Rate Mode. In Variable Frame Rate Mode, you can record quick or slow motion picture by changing the frame rate before recording. [ON]/[OFF] ≥ For information on how to use Variable Frame Rate Mode, refer to page 100. [FRAME RATE] You can adjust the frame rate for Variable Frame Rate Mode. ≥ Set [VFR MODE] to [ON]. (l 100, 183) 1 2 Touch [FRAME RATE]. Touch / to adjust the frame rate.
PAGE 184
HC-X1_E_GC_DVQP1176ZA_eng.book 184 ページ２０１６年１１月２８日月曜日午前１１時４０分 [IR REC COLOR] This changes the color in which images are recorded in Infrared Recording Mode. [Green]/[White] [FOCUS TRANSITION] You can register a focus position to Focus Transition. (l 60) ≥ Switch to Manual Focus. (l 52) [SET]/[OFF] [FOCUS TRANSITION TIME] You can set the length of time in which the focus will shift during Focus Transition. (l 62) [DIRECT]/[FASTEST]/[2-15 SEC.]/[20 SEC.]/[30 SEC.]/[45 SEC.]/[60 SEC.]/[90 SEC.
PAGE 185
HC-X1_E_GC_DVQP1176ZA_eng.book 185 ページ２０１６年１１月２８日月曜日午前１１時４０分 ≥ In the following cases, even when [TIME STAMP] is set to [ON], the date and time of recording are not displayed: j When [REC FORMAT] is set to [SA 480/59.94i] or [SA 576/50.00i] (l 161) j When [2 SLOTS FUNC.
PAGE 186
HC-X1_E_GC_DVQP1176ZA_eng.book 186 ページ２０１６年１１月２８日月曜日午前１１時４０分 Audio Setup All default settings are indicated with underlined text. MENU : [AUDIO SETUP] # desired setting [AUDIO LOW CUT CH1] Reduces the level of low-pitched sound for audio channel 1. [ON]/[OFF] ≥ You may not see the full effect depending on the recording conditions. [AUDIO LOW CUT CH2] Reduces the level of low-pitched sound for audio channel 2. [ON]/[OFF] ≥ You may not see the full effect depending on the recording conditions.
PAGE 187
HC-X1_E_GC_DVQP1176ZA_eng.book 187 ページ２０１６年１１月２８日月曜日午前１１時４０分 [AUDIO ALC CH1] If you set this item to [ON], you can reduce the audio noise of audio channel 1. It will record with natural sound when set to [OFF]. (l 77) ≥ Set [AUDIO LEVEL CH1] to [MANUAL]. (l 76) [ON]/[OFF] [AUDIO ALC CH2] If you set this item to [ON], you can reduce the audio noise of audio channel 2. It will record with natural sound when set to [OFF]. (l 77) ≥ Set [AUDIO LEVEL CH2] to [MANUAL].
PAGE 188
HC-X1_E_GC_DVQP1176ZA_eng.book 188 ページ２０１６年１１月２８日月曜日午前１１時４０分 Output Setup Different menu items are displayed depending on whether this unit is in Recording Mode or Playback Mode. All default settings are indicated with underlined text. MENU : [OUTPUT SETUP] # desired setting [RESOLUTION] This changes the way in which images are output to an external device. (l 128) [SYSTEM]/[1080p]/[1080i]/[DOWN CONV.
PAGE 189
HC-X1_E_GC_DVQP1176ZA_eng.book 189 ページ２０１６年１１月２８日月曜日午前１１時４０分 [DOWN CONV.] This function allows you to select how to display images with a 16:9 aspect ratio on an external monitor with a 4:3 aspect ratio. (l 127) ≥ Set [RESOLUTION] to [DOWN CONV.]. (l 128) [SIDE CROP]/[LETTERBOX]/[SQUEEZE] [HDMI UHD OUTPUT LIMIT] This sets a frame rate when outputting scenes in the recording format [UHD 2160/59.94p 150M] or [UHD 2160/50.00p 150M] from the HDMI OUT terminal. (When [SYSTEM FREQ] is set to [59.
PAGE 190
HC-X1_E_GC_DVQP1176ZA_eng.book 190 ページ２０１６年１１月２８日月曜日午前１１時４０分 [AV OUT] Enable/disable output from the VIDEO OUT terminal or AUDIO OUT terminal. (l 128) [ON]/[OFF] [H/PHONE MODE] Change the type of sound to be output from the headphone and AUDIO OUT terminals. [LIVE]: The sound which has been input from the microphone is output as is. This setting is selected when delays in the sound are annoying.
PAGE 191
HC-X1_E_GC_DVQP1176ZA_eng.book 191 ページ２０１６年１１月２８日月曜日午前１１時４０分 Display setting Different menu items are displayed depending on whether this unit is in Recording Mode or Playback Mode. All default settings are indicated with underlined text. MENU : [DISP SETUP] # desired setting [ZEBRA DETECT 1] Selects the brightness level of the left-leaning zebra patterns on the screen. 1 Touch [ZEBRA DETECT 1]. ≥ Touch [YES]. 2 Touch / to adjust settings. ≥ You can select a value between 50% and 105%.
PAGE 192
HC-X1_E_GC_DVQP1176ZA_eng.book 192 ページ２０１６年１１月２８日月曜日午前１１時４０分 [GUIDE LINES] You can check if the image is level while recording motion pictures and still pictures. The function can also be used to estimate the balance of the composition. / / /[OFF] ≥ The guidelines do not appear on the images actually recorded. ≥ The setting changes as follows when using Focus Assist. (l 56) j The guidelines are not displayed.
PAGE 193
HC-X1_E_GC_DVQP1176ZA_eng.book 193 ページ２０１６年１１月２８日月曜日午前１１時４０分 [FOCUS DISPLAY] This changes the units of focus values. [NUMBER] [feet] [m] [OFF] A value between 0 and 99 is displayed. All values are displayed in feet. All values are displayed in meter. No value is displayed. [ZOOM DISPLAY] This changes the units of zoom values. [NUMBER] A value between 0 and 99 is displayed. [mm] All values are displayed in millimeter. [OFF] No value is displayed.
PAGE 194
HC-X1_E_GC_DVQP1176ZA_eng.book 194 ページ２０１６年１１月２８日月曜日午前１１時４０分 [AUDIO LEVEL METER] Select to display the audio level meter. ≥ (In Playback Mode) Touch the play mode select icon, and set this unit to Motion Picture Playback Mode. (l 113) [ON]/[OFF] [LENS STATUS] Display relating to lens can be switched.
PAGE 195
HC-X1_E_GC_DVQP1176ZA_eng.book 195 ページ２０１６年１１月２８日月曜日午前１１時４０分 [EVF SETTING] Adjusts the brightness and color intensity of the viewfinder. (l 36) [COLOUR]/[BRIGHTNESS]/[CONTRAST] ≥ The default settings are as follows: j [COLOUR]: “0” j [BRIGHTNESS]: “0” j [CONTRAST]: “0” [EYE SENSOR] Adjusts the eye sensor sensitivity. (l 37) ≥ This function’s default setting is “s2”. [SELF SHOOT] Switches the mirror function of the LCD monitor when recording yourself.
PAGE 196
HC-X1_E_GC_DVQP1176ZA_eng.book 196 ページ２０１６年１１月２８日月曜日午前１１時４０分 Other Functions Different menu items are displayed depending on whether this unit is in Recording Mode or Playback Mode. All default settings are indicated with underlined text. MENU : [OTHER FUNCTION] # desired setting [FORMAT MEDIA] The SD card or the external media device can be formatted. (l 42, 138) ≥ Please be aware that if a medium is formatted, then all the data recorded on the medium will be erased and cannot be restored.
PAGE 197
HC-X1_E_GC_DVQP1176ZA_eng.book 197 ページ２０１６年１１月２８日月曜日午前１１時４０分 [ALERT SOUND] Touch screen operation, start and stop of recording can be confirmed with this sound. When [OFF] is selected, the sound is not output at the start/end of recording, etc. [OFF]/ (Volume low)/ (Volume high) 2 Beeps for 4 times When an error occurs. Check the message displayed on the screen. (l 206) [ECONOMY (BATT)] When about 5 minutes have passed without any operation, this unit automatically turns off to save battery life.
PAGE 198
HC-X1_E_GC_DVQP1176ZA_eng.book 198 ページ２０１６年１１月２８日月曜日午前１１時４０分 [INITIAL SET] The menu settings or [FILE SELECT] are reset to the default. (l 151) [ALL]: This is for initializing all menus.* [SCENE]: This is for initializing the setting of each scene number of [FILE SELECT]. [NETWORK]: This is for initializing the [NETWORK SETUP] menu settings. [NO]: This is for not performing initialization. * Settings for [CLOCK SET], [TIME ZONE] and [SYSTEM FREQ] will not be changed.
PAGE 199
HC-X1_E_GC_DVQP1176ZA_eng.book 199 ページ２０１６年１１月２８日月曜日午前１１時４０分 Network Setup All default settings are indicated with underlined text. MENU : [NETWORK SETUP] # desired setting [USER ACCOUNT] Set up a login user account for the AG ROP application. (l 143) [SET]/[OFF] [WIRELESS SETUP] Set the wireless LAN connection method.
PAGE 200
HC-X1_E_GC_DVQP1176ZA_eng.book 200 ページ２０１６年１１月２８日月曜日午前１１時４０分 [NETWORK SETUP PASSWORD] This will set/clear the Password to limit the startup of the [NETWORK SETUP] menu. By setting the Password, it will prevent erroneous operation, prevent wrongful use of the wireless LAN function by third party, and protect the set personal information. [Setup]/[Delete] 1 2 Touch [Setup]. Enter a password (six characters). ≥ After finish entering the Password, touch [Enter].
PAGE 201
HC-X1_E_GC_DVQP1176ZA_eng.book 201 ページ２０１６年１１月２８日月曜日午前１１時４０分 Video Setup All default settings are indicated with underlined text. ≥ Press the THUMBNAIL button to switch this unit to the Playback Mode. ≥ Touch the play mode select icon, and set this unit to Motion Picture Playback Mode. (l 113) MENU : [VIDEO SETUP] # desired setting [REPEAT PLAY] Playback of the first scene starts after playback of the last scene finishes when set to [ON].
PAGE 202
HC-X1_E_GC_DVQP1176ZA_eng.book 202 ページ２０１６年１１月２８日月曜日午前１１時４０分 Picture Setup ≥ Press the THUMBNAIL button to switch this unit to the Playback Mode. ≥ Touch the play mode select icon, and set this unit to Still Picture Playback Mode. (l 113) MENU : [PHOTO SETUP] # desired setting [SCENE PROTECT] Still pictures can be protected so that they are not deleted by mistake. (Even if you protect some still pictures, formatting the SD card will delete them.) (l 122) [DELETE] Deletes a still picture.
PAGE 203
HC-X1_E_GC_DVQP1176ZA_eng.book 203 ページ２０１６年１１月２８日月曜日午前１１時４０分 Display Indications ∫ Recording indications Example: Display in English    I- REC HDMI TC 00:00:00:00 R 1h20m R 1h20m EX.SENS. DRS FLUO D 5X 5600K Ach ND1/64 0dB A.SHTR 1/100 150M 25:25.00p FBC VFR 99% SHUTTER OPEN MNL DUAL 50M , DUAL 8M A TC 00:00:00.00/TC 00:00:00:00 Counter display (l 78) I- Interval Recording (l 182) I-REC (Red) Interval Recording (Recording) P- PRE-REC (l 95, 183) EXTENDED SENSITIVITY (l 165) H.
PAGE 204
HC-X1_E_GC_DVQP1176ZA_eng.book 204 ページ２０１６年１１月２８日 , Recording mode (l 160) When [AUDIO ALC CH1], [AUDIO ALC CH2], [AUDIO ALC LINK] are enabled (l 77) 25:25.00p Frame rate in Variable Frame Rate Mode (l 100, 183) ALC 59.94p, 59.94i, 50.00p, 50.00i, 29.97p, 25.00p, 24.00p, 23.98p Frame rate (l 161) When [AUDIO ALC CH1], [AUDIO ALC CH2], [AUDIO ALC LINK] are enabled and audio cannot be recorded.
PAGE 205
HC-X1_E_GC_DVQP1176ZA_eng.book 205 ページ２０１６年１１月２８日 ∫ Playback indications 10 No.0010 150M 4K 50.
PAGE 206
HC-X1_E_GC_DVQP1176ZA_eng.book 206 ページ２０１６年１１月２８日月曜日午前１１時４０分 Display Messages Major confirmation/error messages to be indicated on the screen in text. During recording/playback Display Description Behavior and cause CHECK CARD. The SD card is not supported by this unit. ≥ Check the SD card. THIS CARD CANNOT RECORD IN VIDEO MODE. This is displayed when the SD card has a capacity of less than 4 GB. ≥ Use an SD card with a capacity of 4 GB or more. INCOMPATIBLE CARD. CHECK CARD SPEED.
PAGE 207
HC-X1_E_GC_DVQP1176ZA_eng.book Display CANNOT RECORD - DATE CAPACITY IS FULL. 207 ページ２０１６年１１月２８日 Description 月曜日午前１１時４０分 Behavior and cause This is displayed when you try to record in excess of the maximum number of scenes allowed for one SD card. ≥ The operation will stop. ≥ Replace the SD card or delete unnecessary scenes. INVALID This is displayed when the operation is invalid. ≥ Before performing the operation, wait until this unit is ready for it. ERROR - UNABLE TO REPAIR DATA.
PAGE 208
HC-X1_E_GC_DVQP1176ZA_eng.book 208 ページ２０１６年１１月２８日月曜日午前１１時４０分 During thumbnail and menu operation Display Description Behavior and cause NO DATA. There are no scenes in the currently selected recording mode option and recording format option. ≥ Select a recording mode option or recording format option containing recorded scenes. CANNOT DELETE. The content versions do not match. This is displayed when you try to delete scenes recorded with another device, for example.
PAGE 209
HC-X1_E_GC_DVQP1176ZA_eng.book 209 ページ２０１６年１１月２８日月曜日午前１１時４０分 During USB Device mode Display DISCONNECT USB CABLE. Description An error has occurred while accessing the SD card, or the OS is not supported. Behavior and cause ≥ Check the SD card. ≥ Check to see if the OS is supported. During USB Host mode Display Description Behavior and cause This external media cannot be used. Disconnect the USB cable from this unit.
PAGE 210
HC-X1_E_GC_DVQP1176ZA_eng.book 210 ページ２０１６年１１月２８日月曜日午前１１時４０分 During copying between SD cards or copying to an external media device Display Description Behavior and cause PLEASE CHECK THE EXTERNAL MEDIA. Copying cannot be performed due to, for example, a problem with the copy destination media device. ≥ Check the copy destination media device. Use destination media formatted with same as SD card.
PAGE 211
HC-X1_E_GC_DVQP1176ZA_eng.book Display CANNOT COPY - DATE CAPACITY IS FULL. CANNOT COPY - THE NUMBER OF SCENES HAS REACHED MAXIMUM. 211 ページ２０１６年１１月２８日 Description This is displayed when no more scenes can be copied after the maximum limit set by applicable standards is reached, for example. COULD NOT COPY SOME SCENES. This is displayed when some scenes cannot be copied after the maximum limit set by applicable standards is reached, for example. COPY FAILED. PLEASE CHECK THE CARD.
PAGE 212
HC-X1_E_GC_DVQP1176ZA_eng.book 212 ページ２０１６年１１月２８日月曜日午前１１時４０分 Display Warning Indications When an error is detected immediately after this unit is turned on or while it is being operated, the status indicator, on-screen displays and the AG ROP application screen (during AG ROP connection) inform you of the error. Status indicator It flashes once per second. On-screen display System error AG ROP application screen [ WARNING ] flashes four times per second.
PAGE 213
HC-X1_E_GC_DVQP1176ZA_eng.book 213 ページ２０１６年１１月２８日 Status indicator 月曜日 It flashes once per second. On-screen display AG ROP application screen Recording error s [ WARNING ] flashes four times per second. Meaning of the warning A recording error or recording circuit setting error has occurred. Recording/playback The recording may either continue or stop. Solution Turn off and on this unit. If the warning persists, consult your dealer.
PAGE 214
HC-X1_E_GC_DVQP1176ZA_eng.book 214 ページ２０１６年１１月２８日 Status indicator The card is nearly full 午前１１時４０分 s On-screen display The remaining recordable time flashes red. (When it is less than 1 minute) AG ROP application screen [ WARNING ] flashes once per second. (When it is less than 1 minute) Meaning of the warning Recording/playback Solution Status indicator On-screen display The cooling fan has stopped 月曜日 The SD card is almost out of space. The recording continues.
PAGE 215
HC-X1_E_GC_DVQP1176ZA_eng.book 215 ページ２０１６年１１月２８日月曜日午前１１時４０分 Others Troubleshooting ∫ It is not a malfunction in following cases The lens, the viewfinder or LCD monitor fog up. ≥ This is due to condensation. This is not a malfunction. Please refer to page 8. A clicking sound is heard when the unit is shaken. ≥ This is the sound of the lens moving and is not a defect. This sound will no longer be heard when the unit is turned on and switch to Recording Mode. Object seems to be warped.
PAGE 216
HC-X1_E_GC_DVQP1176ZA_eng.book 216 ページ２０１６年１１月２８日月曜日午前１１時４０分 Indication Problem Function display (Remaining Display, Counter Display, etc.) is not displayed. Check points ≥ [CARD & BATTERY] or [OTHER DISPLAY] of the [DISP SETUP] is [OFF]. (l 194) ≥ Press the COUNTER button to switch the counter display. (l 78) Recording Problem Check points The unit arbitrarily stops recording. ≥ Use an SD card that can be used for motion picture recording.
PAGE 217
HC-X1_E_GC_DVQP1176ZA_eng.book 217 ページ２０１６年１１月２８日月曜日午前１１時４０分 Playback Problem Check points Scenes/still pictures cannot be played back. ≥ Any scenes/still pictures where the thumbnails are displayed as cannot be played back. ≥ In most cases, is displayed for the following scenes: j Scenes recorded with another device or edited with editing software j Scenes with damaged data ≥ The thumbnails of scenes recorded on other devices with different system frequencies are indicated with .
PAGE 218
HC-X1_E_GC_DVQP1176ZA_eng.book 218 ページ２０１６年１１月２８日月曜日午前１１時４０分 With a PC Problem Check points When connected by the USB Cable, this unit is not detected by the PC. ≥ After re-inserting the SD card into the unit, reconnect the USB Cable. ≥ Select another USB terminal on the PC. ≥ Check the operating environment. (l 132) ≥ Connect the USB Cable again after restarting the PC and turning on this unit again. When the USB Cable is disconnected, an error message will appear on the PC.
PAGE 219
HC-X1_E_GC_DVQP1176ZA_eng.book 219 ページ２０１６年１１月２８日月曜日午前１１時４０分 About recovery If faulty management information is found, the messages may appear and a repair is performed. (Repairing may take time depending on the error.) ≥ is displayed when abnormal management information is detected when the scenes are displayed in thumbnail. Use a sufficiently charged battery or the AC adaptor. Depending on the condition of the data, it may not be possible to completely repair the data.
PAGE 220
HC-X1_E_GC_DVQP1176ZA_eng.book 220 ページ２０１６年１１月２８日月曜日午前１１時４０分 Others About copyright ∫ Carefully observe copyright laws Recording of pre-recorded tapes or discs or other published or broadcast material for purposes other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted. ∫ Licenses ≥ SDXC Logo is a trademark of SD-3C, LLC.
PAGE 221
HC-X1_E_GC_DVQP1176ZA_eng.book 221 ページ２０１６年１１月２８日 This product incorporates the following software: (1) the software developed independently by or for Panasonic Corporation, (2) the software owned by third party and licensed to Panasonic Corporation, (3) the software licensed under the GNU General Public License, Version 2.0 (GPL V2.0), (4) the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL V2.
PAGE 222
HC-X1_E_GC_DVQP1176ZA_eng.book 222 ページ２０１６年１１月２８日月曜日午前１１時４０分 Others Recording functions that cannot be used simultaneously Due to the specifications of this unit, depending on the recording function being used, it is not possible to use or select certain other recording functions. ≥ “±”: Available; “s”: Not available* * “Not available” includes instances where the desired function cannot be used or selected.
PAGE 223
HC-X1_E_GC_DVQP1176ZA_eng.book 223 ページ２０１６年１１月２８日月曜日午前１１時４０分 Others Recording modes/approximate recordable time ≥ SD cards are only mentioned with their main memory size. The stated times are the approximate recordable times for continuous recording. ≥ “h” is an abbreviation for hour, “min” for minute and “s” for second. ≥ If recording for long periods, prepare batteries for 3 or 4 times the period you wish to record for.
PAGE 224
HC-X1_E_GC_DVQP1176ZA_eng.book 224 ページ２０１６年１１月２８日 System frequency setting (l 160) Recording format 月曜日午前１１時４０分 SD card 4 GB 16 GB 64 GB [UHD 2160/50.00p 150M] s s 55 min [UHD 2160/25.00p 100M] s 20 min 1 h 20 min [FHD 1080/50.00p ] s 10 min 40 min [FHD 1080/50.00p 100M] s 20 min 1 h 20 min 10 min 40 min 2 h 40 min s 10 min 40 min 10 min 40 min 2 h 40 min [FHD 1080/50.00p 50M] [FHD 1080/25.00p [50.00Hz] ] [FHD 1080/25.00p 50M] [FHD 1080/50.
PAGE 225
HC-X1_E_GC_DVQP1176ZA_eng.book 225 ページ２０１６年１１月２８日月曜日午前１１時４０分 Others Approximate number of recordable pictures ≥ SD cards are only mentioned with their main memory size. The stated number is the approximate number of recordable pictures. Picture size Aspect ratio 8.8M 4096k2160 17:9 SD card 8.3M 3840k2160 2.1 M 1920k1080 16:9 0.
PAGE 226
HC-X1_E_GC_DVQP1176ZA_eng.book 226 ページ２０１６年１１月２８日月曜日午前１１時４０分 Others Specification 4K Video Camera General Camera unit Power: DC 7.28 V (When using battery) DC 12 V (When using AC adaptor) Power consumption: 19.7 W (When using LCD monitor) indicates safety information Ambient operating temperature: 0 oC to 40 oC Ambient operating humidity: 10%RH to 80%RH (no condensation) Mass: Approx. 2.0 kg (body only, excluding lens hood, battery, and accessories) Approx. 2.
PAGE 227
HC-X1_E_GC_DVQP1176ZA_eng.book 227 ページ２０１６年１１月２８日 Shutter speed: When [SYSTEM FREQ] = [59.94Hz] ≥ 60i/60p mode; 1/60, 1/100, 1/120, 1/180, 1/250, 1/350, 1/500, 1/750, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000, 1/8000 sec. ≥ 30p mode; 1/30, 1/50, 1/60, 1/100, 1/120, 1/180, 1/250, 1/350, 1/500, 1/750, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000, 1/8000 sec. ≥ 24p mode; 1/24, 1/48, 1/50, 1/60, 1/100, 1/120, 1/180, 1/250, 1/350, 1/500, 1/750, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000, 1/8000 sec.
PAGE 228
HC-X1_E_GC_DVQP1176ZA_eng.book 228 ページ２０１６年１１月２８日 Memory card recorder Recording media: SDHC Memory Card (4 GB to 32 GB)/ SDXC Memory Card (48 GB to 128 GB); UHS-I supported Refer to page 29 for details on SD cards usable in this unit. Recording slots: 2 slots System frequency: 59.94 Hz, 50.00 Hz Motion picture recording: Recording method; MOV, MP4, AVCHD Recording format; ≥ When [REC MODE] = [MOV], [MP4] [4K 2160/24.00p 100M]; Average 100 Mbps (VBR) (When [SYSTEM FREQ] = [59.94Hz]) [UHD 2160/59.
PAGE 229
HC-X1_E_GC_DVQP1176ZA_eng.book 229 ページ２０１６年１１月２８日 Digital video Video signal for external output: 8 bit 4:2:2*2 *2 It is set to 8 bit 4:2:0 when UHD 59.94p or UHD 50.00p is selected. Recording video signal: 8 bit 4:2:0 Video compression format: MPEG-4 AVC/H.
PAGE 230
HC-X1_E_GC_DVQP1176ZA_eng.book 230 ページ２０１６年１１月２８日月曜日午前１１時４０分 Audio input Other input/output Built-in microphone: Supports stereo microphone AUDIO INPUT1/AUDIO INPUT2 terminal: XLRk2, 3-pin Input high impedance, LINE/MIC/MIC_48 V (switch selection) ≥ LINE; _4 dBu/0 dBu (selectable menu) ≥ MIC; `40 dBu /`50 dBu /`60 dBu (selectable menu) CAM REMOTE terminal: 2.5 mm diameter super mini jackk1 (ZOOM, S/S) 3.
PAGE 231
HC-X1_E_GC_DVQP1176ZA_eng.book 231 ページ２０１６年１１月２８日 AC adaptor Power source: AC 100 V to 240 V, 50 Hz/60 Hz, 1.2 A Power output: DC 12 V, 3.0 A 月曜日午前１１時４０分 Battery charger Input voltage: DC 12 V, 3.0 A Output voltage: DC 8.4 V, 4.0 A indicates safety information indicates safety information Ambient operating temperature: 0 oC to 40 oC Ambient operating humidity: 10%RH to 90%RH (no condensation) Mass: Approx.
PAGE 232
HC-X1_E_GC_DVQP1176ZA_eng.book 232 ページ２０１６年１１月２８日月曜日午前１１時４０分 EU Manufactured by: Panasonic Corporation Kadoma, Osaka, Japan Importer for Europe: Panasonic Marketing Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany Panasonic Corporation Web site: http://www.panasonic.