HC-X900M&X800P&PC&PU-VQT4C76_mst.book 1 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Owner’s Manual High Definition Video Camera Model No. HC-X900M HC-X800 Before connecting, operating or adjusting this product, please read the instructions completely. For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 2 ページ ２０１２年１月１１日 Dear Customer, Date of Purchase Thank you for choosing Panasonic! You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. The serial number is on the tag located on the back of your camera. Be sure to retain this manual as your convenient camera information source.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 3 ページ ２０１２年１月１１日 水曜日 午後１０時６分 THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 4 ページ ２０１２年１月１１日 水曜日 午後１０時６分 THE FOLLOWING APPLIES ONLY IN THE U.S.A. AND CANADA. AC adaptor This AC adaptor operates on AC between 110 V and 240 V. But ≥ In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power supply only. ≥ When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to suit the AC outlet configuration.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 5 ページ ２０１２年１月１１日 水曜日 午後１０時６分 CAUTION ≥ Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer. ≥ When disposing the batteries, please contact your local authorities or dealer and ask for the correct method of disposal. Warning Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed call your doctor.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 6 ページ ２０１２年１月１１日 水曜日 午後１０時６分 IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 7 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Precautions USE & LOCATION WARNING ≥ TO AVOID SHOCK HAZARD ... Your camera and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your camera if it gets wet. Your camera has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 8 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ About the recording format for recording motion pictures ∫ Handling of built-in memory [HC-X900M] You can select from AVCHD* or iFrame recording formats to record motion pictures using this unit. (l 68) * It is compatible with AVCHD 3D or AVCHD Progressive (1080/60p). This unit is equipped with the built-in memory. When using this component, pay attention to the following points.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 9 ページ ∫ HC-X900M About Condensation (When the lens, the viewfinder or LCD Monitor is fogged up) Condensation occurs when the ambient temperature or humidity changes. Be careful of condensation since it causes lens, viewfinder and LCD monitor stains, fungus and camera malfunction. ≥ For more details about the cause and action required for condensation, refer to page 161.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 10 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Contents Accessories.............................................12 Quick Guide.............................................13 Preparation Advanced (Recording) Names and Functions of Main Parts ..... 17 Power supply........................................... 20 Inserting/removing the battery........... 20 Charging the battery ......................... 21 Charging and recording time............. 22 Recording to a card ................
Copying between SD card and Built-in Memory [HC-X900M] ............................. 121 Connecting a DVD burner to copy to/ play back a disc .................................... 123 Preparing for copying/ playing back .................................... 123 Copying to discs.............................. 125 Playing back the copied disc........... 127 Managing the copied disc ............... 128 Dubbing with a Blu-ray disc recorder, video devices, etc. ................................
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 12 ページ ２０１２年１月１１日 水曜日 Accessories Check the accessories before using this unit. Keep the accessories out of reach of children to prevent swallowing. Product numbers correct as of Jan. 2012. These may be subject to change.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 13 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Quick Guide ∫ Inserting the battery Open the LCD monitor and install the battery by inserting it in the direction shown in the figure. ∫ Inserting/removing an SD card ≥ Insert the battery until it clicks and locks. ∫ Charging the battery A DC input terminal 1 Connect the AC cable to the AC adaptor, then the AC outlet. 2 Connect the AC adaptor to the DC input terminal.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 14 ページ ∫ Turning the unit on/off Turning the unit on and off with the power button Open the LCD monitor and press the power button to turn on the unit. ２０１２年１月１１日 水曜日 午後１０時６分 To turn off the unit HC-X900M HC-X800 HC-X900M B The status indicator goes off. HC-X800 ∫ Selecting a mode Operate the mode switch to change the mode to , or . HC-X900M A The status indicator lights on.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 15 ページ ∫ How to use the touch screen You can operate by directly touching the LCD monitor (touch screen) with your finger. Touch Touch and release the touch screen to select icon or picture. 水曜日 午後１０時６分 ∫ Selecting a media to record HC-X900M 1) 2) Change the mode to Select the menu. MENU 3) Slide while touching Move your finger while pressing on the touch screen. ２０１２年１月１１日 or . : [MEDIA SELECT] Touch the media to record motion pictures or still pictures.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 16 ページ 4) ∫ Motion picture/Still picture playback 1) 2) Change the mode to . Touch the play mode select icon A. ALL 3) HC-X900M Select the media type D and then select the still picture B or the recording format of the motion picture C you wish to play back. 午後１０時６分 ≥ It will switch to the screen displaying and thumbnail scroll lever E when no operation is performed for approximately 5 seconds on the thumbnail display screen.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 17 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Preparation Names and Functions of Main Parts 10 AV MULTI 1 14 15 16 17 18 78 9 11 12 LCD monitor (Touch screen) (l 28) ≥ It can open up to 90o. ≥ It can rotate up to 180o A towards the lens or 90o B towards the opposite direction. Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 18 ページ 19 ２０１２年１月１１日 水曜日 午後１０時６分 23 24 20 21 22 25 26 19 SD card cover (l 25) 20 Tripod receptacle ≥ If you attach a tripod which has 5.5 mm (0.22 q) screw or larger, it may damage this unit.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 19 ページ 33 Shoe adaptor release lever [SHOE ADAPTOR RELEASE] (l 172) 34 Microphone terminal [MIC] ≥ A compatible plug-in powered microphone can be used as an external microphone. ≥ Audio will be stereo (2 ch) with the external microphone input. ≥ (Microphone input level meter) is displayed when the external microphone is connected. (l 76) ≥ When the unit is connected with the AC adaptor, sometimes noise may be heard depending on the microphone type.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 20 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Preparation Power supply ∫ About batteries that you can use with this unit The battery that can be used with this unit is VW-VBN130/VW-VBN260. ≥ The unit has a function for distinguishing batteries which can be used safely. The dedicated battery (VW-VBN130/VW-VBN260) supports this function.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 21 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Charging the battery When this unit is purchased, the battery is not charged. Charge the battery fully before using this unit for the first time. The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always “live” as long as the AC adaptor is connected to an electrical outlet. Important: ≥ Use the supplied AC adaptor. Do not use the AC adaptor of another device.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 22 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Charging and recording time ∫ Charging/Recording time ≥ Temperature: 25 oC (77 °F)/humidity: 60%RH ≥ HC-X900M When using the viewfinder (times in parentheses are when using the LCD monitor) HC-X900M Battery model number [Voltage/Capacity (minimum)] Supplied battery/ VW-VBN130 (optional) [7.2 V/1250 mAh] VW-VBN260 (optional) [7.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 23 ページ ２０１２年１月１１日 水曜日 午後１０時６分 HC-X800 Battery model number [Voltage/Capacity (minimum)] Supplied battery/ VW-VBN130 (optional) [7.2 V/1250 mAh] VW-VBN260 (optional) [7.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 24 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Preparation Recording to a card The unit can record still pictures or motion pictures to an SD card or built-in memory. To record to an SD card, read the following. This unit (an SDXC compatible device) is compatible with SD Memory Cards, SDHC Memory Cards and SDXC Memory Cards. When using an SDHC Memory Card/SDXC Memory Card with other equipment, check the equipment is compatible with these Memory Cards.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 25 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Inserting/removing an SD card When using an SD card not from Panasonic, or one previously used on other equipment, for the first time on this unit, format the SD card. (l 50) When the SD card is formatted, all of the recorded data is deleted. Once the data is deleted, it cannot be restored. Caution: Check that the access lamp has gone off. 1 Open the SD card cover and insert/remove the SD card into/ from the card slot.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 26 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Preparation Turning the unit on/off You can turn the unit on and off using the power button, the LCD monitor or the viewfinder. Turning the unit on and off with the power button Open the LCD monitor and press the power button to turn on the unit. HC-X800 HC-X900M To turn off the unit Hold down the power button until the status indicator goes off. A The status indicator lights on.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 27 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ To turn off the unit HC-X800 HC-X900M B The status indicator goes off. HC-X900M ≥ The unit will not turn off unless the LCD monitor is closed and the viewfinder is retracted. ≥ The unit will not turn off while recording motion pictures even if the LCD monitor is closed and the viewfinder is retracted. HC-X800 ≥ The unit will not turn off while recording motion pictures even if the LCD monitor is closed.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 28 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Preparation Preparation of the LCD monitor/ Viewfinder [HC-X900M] The viewfinder is turned off and the LCD monitor is turned on when the LCD monitor is opened. The viewfinder is turned on when the LCD monitor is closed and the viewfinder is extended. ≥ Live image recording or 3D recordings can be viewed in 3D on the LCD monitor. (l 88, 114) There are differences in the way that different people experience 3D images.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 29 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ About the operation icons HC-X800 HC-X900M / / / : These icons are used to switch the menu and thumbnail display page, for item selection and setting etc. : Touch to return to the previous screen such as when setting menus. About the Touch Menu Touch Touch (left side)/ (right side) of (left side)/ on the Touch Menu to switch the operation icons. (right side) of on the Touch Menu.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 30 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ To display the Touch Menu Display of the Touch Menu will disappear when no touch operation is performed for a specific period of time. To display it again, touch . ≥ Do not touch the LCD monitor with hard pointed tips, such as ball point pens. Preparation Setting date and time When the unit is turned on for the first time, a message asking you to set the date and time will appear.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 31 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Basic Before recording ∫ Basic camera positioning 1 Hold the unit with both hands. 2 Put your hand through the grip belt. 3 It is convenient to use the recording button icon A when holding the unit at waist level. ≥ When recording, make sure your footing is stable and there is no danger of colliding with another person or object. ≥ When you are outdoors, record pictures with the sunlight behind you.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 32 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ If you use the Filter Kit (optional), the Conversion Lens (optional) or the 3D Conversion Lens (optional), remove the lens hood. Basic Selecting a media to record [HC-X900M] The card and built-in memory can be selected separately to record motion pictures or still pictures. 1 2 Change the mode to or . Select the menu. (l 42) MENU 3 : [MEDIA SELECT] Touch the media to record motion pictures or still pictures.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 33 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Basic Recording motion pictures 1 2 3 Change the mode to . (l 27) Open the LCD monitor or extend the viewfinder. Press the recording start/stop button to start recording. A Recording button icon B When you begin recording, ; changes to ¥. 4 Press the recording start/stop button again to pause recording. T W ≥ Recording can also be started/stopped by touching the recording button icon.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 34 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ HC-X900M While recording is in progress, the recording will not stop even if the LCD monitor is closed and the viewfinder is retracted. HC-X800 While recording is in progress, the recording will not stop even if the LCD monitor is closed. ≥ HC-X900M Put the unit in Pause mode when connecting or disconnecting an external microphone with the MIC terminal. ≥ Please refer to page 163 for detail about the approximate recordable time.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 35 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Basic Recording still pictures 1 2 3 Change the mode to . (l 27) Open the LCD monitor or extend the viewfinder. Press the button halfway. (For Auto Focus only) Focus indication: A Focus indication ± (The white lamp flashes.): Focusing ¥ (The green lamp lights up.): When in focus No mark: When focusing is unsuccessful. B Focus area (area inside brackets) 4 Press the button fully.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 36 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ About the screen indications in Still Picture Recording Still picture operation indicator (l 147) R3000 16 M MEGA MEGA Optical Image Stabilizer (l 35) AF assist lamp (l 82) ß MEGA Size of still pictures (l 79) Optical Image Stabilizer (l 55) ßj R3000 16 M Remaining number of still pictures ≥ Flashes in red when [0] appears.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 37 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ If simultaneous recording is used while recording a motion picture, the recordable time remaining will shorten. If the unit is turned off or the mode switch operated, the recordable time remaining may lengthen. Basic Intelligent Auto Mode The following modes (appropriate for the condition) are set just by pointing the unit to what you want to record.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 38 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ Depending on the recording conditions, the unit may not enter the desired mode. ≥ In the Portrait, Spotlight and Low Light Mode, the face will be surrounded by white frame when detected. In the Portrait Mode, a subject that is bigger and close to center of the screen will be surrounded by an orange frame. (l 72) ≥ Using a tripod is recommended in Night Portrait and Night Scenery Mode.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 39 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Basic Motion picture/Still picture playback 1 2 3 Change the mode to . (l 27) ALL Touch the play mode select icon A. (l 29) HC-X900M Select the media type D and then select the still picture B or the recording format of the motion picture C you wish to play back. HC-X800 Select the still picture B or the recording format of the motion picture C you wish to play back. ≥ Touch [ENTER].
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 40 ページ 5 ２０１２年１月１１日 水曜日 午後１０時６分 Select the playback operation by touching the operation icon. 0h01m30s F Operation icon ≥ Operation icons and screen display will disappear when no touch operation is performed for a specific period of time. To display them again, touch the screen. ≥ HC-X900M The scene or still picture being played back is converted to 3D image/2D image and played back when the / is touched.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 41 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ The elapsed time for playback indication will be reset to 0h00m00s each scene. ≥ When playing back with [ALL AVCHD] selected, the screen may become black momentarily at the time the scene switches. Motion picture compatibility ≥ This unit is based on AVCHD 3D/AVCHD Progressive/AVCHD. AVCHD 3D format ≥ Video signals for the AVCHD 3D that can be played back with this unit are 1920k1080/60i.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 42 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Basic Using the menu screen ≥ Touch (left side)/ (right side) of on the Touch Menu to display MENU . (l 29) 1 Touch MENU . Q. MENU Using the quick menu This allows quick setting of some of the menus. ≥ Touch (left side)/ (right side) of Q. on the Touch Menu to display MENU . (l 29) 1 MENU 2 Touch the top menu A. Touch Q. MENU . The following menus can be set. Touch the desired menu.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 43 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Basic Using the Setup Menu ≥ The items displayed differ depending on the position or settings of the mode switch. Select the menu. MENU : [SETUP] # desired setting [DISPLAY] [5 SECONDS]/[ON] Set the display method for the screen information display. [5 SECONDS]: Information is displayed on the screen for 5 seconds after starting the recording mode, starting to playback, or touching the screen.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 44 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ When the home region is set for the first time, the screen for selecting home/travel destination appears after setting the home region successively. If the home region has already been set once, execute the menu operation for Step 1. 5 (Only when setting the region of your travel destination) Touch / to select your travel destination and touch [ENTER]. ≥ Touch [DAYLIGHT SAVING] to set daylight saving time.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 45 ページ HC-X800 ２０１２年１月１１日 水曜日 午後１０時６分 [SIMPLE]/[DETAIL]/[OFF] [EXT. DISPLAY] Please refer to page 110. [ECONOMY (BATT)] [ON]/[OFF] When about 5 minutes have passed without any operation, this unit automatically turns off to save battery life. ≥ This unit will not automatically turn off even if the [ECONOMY (BATT)] is set to [ON] in following cases: j Using the AC adaptor* j Using the USB cable for PC, DVD burner etc.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 46 ページ ≥ Change the mode to 1 2 or ２０１２年１月１１日 水曜日 午後１０時６分 . Set [QUICK START] to [ON]. Close the LCD monitor and retract the viewfinder. HC-X800 HC-X900M The status indicator A flashes green and the unit goes into Quick Start Standby Mode. ≥ The lens cover does not close. 3 Open the LCD monitor or extend the viewfinder. HC-X800 HC-X900M The status indicator A lights red and the unit is put into recording pause.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 47 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [ON]/[OFF] HC-X900M [REMOTE CONTROL] Please refer to page 52. [REC LAMP] [ON]/[OFF] HC-X900M The recording lamp lights up during recording and flashes when the unit receives a signal from the remote control or when the Self-timer is counting down. HC-X800 The recording lamp lights up during recording and flashes when the Self-timer is counting down. When this is set to [OFF], it does not light during recording.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 48 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [POWER LCD] HC-X900M HC-X800 : : [ON]/[OFF] A / +2 / +1 / 0 / -1 This makes it easier to view the LCD monitor in bright places including outdoors. ≥ These settings will not affect the images actually recorded. ≥ It is possible to set from the quick menu.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 49 ページ [HDMI RESOLUTION] ２０１２年１月１１日 水曜日 午後１０時６分 [AUTO]/[1080p]/[1080i]/[480p] Please refer to page 110. [VIERA Link] [ON]/[OFF] Please refer to page 112. [TV ASPECT] [16:9]/[4:3] Please refer to page 109. HC-X900M [HDMI]/[LCD] [3D OUTPUT] Please refer to page 115. HC-X800 [AUTO]/[2D] [3D PLAYBACK] Please refer to page 118. [INITIAL SET] Set to [YES] for changing the menu settings back to the default condition.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 50 ページ ２０１２年１月１１日 水曜日 午後１０時６分 HC-X800 [FORMAT CARD] Please be aware that if a medium is formatted, then all the data recorded on the medium will be erased and cannot be restored. Back up important data on a PC, DVD disc etc. (l 123, 136) ≥ When formatting is complete, touch [EXIT] to exit the message screen. ≥ Perform a physical formatting of the SD card when the SD card is to be disposed/ transferred.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 51 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ The SD card requires some space to store information and manage system files, so the actual usable space is slightly less than the indicated value. The usable space is generally calculated as 1 GB=1,000,000,000 bytes. The capacities of this unit, PCs and software are expressed as 1 GB=1,024k1,024k1,024=1,073,741,824 bytes. Therefore, the indicated value of the capacity appears to be smaller.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 52 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Basic Using with the remote control [HC-X900M] Select the menu. MENU : [SETUP] # [REMOTE CONTROL] # [ON] 1 2 3 4 START/ STOP /VOL DATE/TIME EXT DISPLAY SEARCH PLAY SEARCH STILL ADV PAUSE STILL ADV SKIP STOP 5 6 7 8 9 9 Date/time button [DATE/TIME] (l 44) 10 Menu button [MENU] 11 OK button [OK] * means that these buttons function in the same manner as the corresponding buttons on the unit.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 53 ページ CAUTION ≥ Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer. ≥ When disposing the batteries, please contact your local authorities or dealer and ask for the correct method of disposal. ２０１２年１月１１日 水曜日 午後１０時６分 Operation of direction buttons/OK button 1 Press a direction button.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 54 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Recording) Using the zoom Zoom lever/Zoom button icons T side: Close-up recording (zoom in) W side: Wide-angle recording (zoom out) T W 6 W T T W A Zoom bar ≥ Maximum zoom ratio for recording motion pictures can be set with [ZOOM MODE]. (l 67) ≥ You can also zoom by simply touching the LCD monitor. (Touch Zoom: l 57) ∫ About the zoom bar The zoom bar is displayed during the zoom operation.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 55 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Zoom ratio during the Still Picture Recording Mode The zoom ratio can be expanded up to 25k without degrading the picture quality for the Still Picture Recording Mode. (Extra Optical Zoom) ≥ Extra optical zoom ratio varies depending on the setting of [PICTURE SIZE] and [ASPECT RATIO]. (l 79, 80) ≥ If you take your finger off the zoom lever during zoom operation, the operation sound may be recorded.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 56 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Changing Image Stabilizer Mode (Motion Picture Recording Mode) MENU : [RECORD SETUP] # [HYBRID O.I.S.] # [ON] or [OFF] When set to [ON], you can further improve image stabilization for recording while walking, or holding the unit and recording a distant subject with zoom. ≥ This function’s default setting is [ON]. (Still Picture Recording Mode) MENU : [RECORD SETUP] # [O.I.S.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 57 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Recording) Recording with the Touch function You can record using convenient functions just by the easy operation of touching the screen. 1 2 Touch (left side)/ (right side) of on the Touch Menu to display Touch function icons. (l 29) T W Touch the Touch function icon. (e.g. AF/AE tracking) ≥ To cancel, touch the Touch function icon again. (Optical Image Stabilizer Lock is canceled by releasing the finger touching .
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 58 ページ ２０１２年１月１１日 水曜日 午後１０時６分 AF/AE tracking It is possible to set the focus and exposure to the subject specified on the touch screen. The focus and exposure will keep following the subject automatically even if it moves. (Dynamic tracking) 1 Touch . ≥ When [FACE RECOG.] (l 70) is [ON] and a registered face is detected, the target is automatically locked. 2 Touch the object and lock the target.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 59 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Optical Image Stabilizer Lock In Motion Picture Recording Mode, you can further improve optical image stabilization by touching and holding . With this function, you can further reduce the effects of the shake that tends to occur when using zoom. 1 2 Press the Optical Image Stabilizer button to turn the image stabilizer on. Touch and hold . ≥ Icon is displayed in A while you are touching and holding .
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 60 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Recording) Recording functions of operation icons Select the operation icons to add different effects to the images to be recorded. 1 Touch (left side)/ (right side) of display the operation icons. (l 29) 2 Touch an operation icon. on the Touch Menu to PRE-REC (e.g. PRE-REC) ≥ Select the operation icon again to cancel the function. ≥ Refer to the respective pages for canceling the following functions.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 61 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Fade When you start recording, the image/audio gradually appears. (Fade in) When you pause recording, the image/audio gradually disappears. (Fade out) ≥ The Fade setting is canceled when the recording stops. (Fade in) ∫ To select the color for fade in/out (Fade out) : [RECORD SETUP] # [FADE COLOR] # [WHITE] or [BLACK] MENU ≥ The thumbnails of scenes recorded using fade in become black (or white).
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 62 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ After setting PRE-REC, if recording starts in less than 3 seconds, motion pictures taken 3 seconds before pressing the recording start/stop button cannot be recorded. ≥ Images displayed on the thumbnail during playback will differ from the motion pictures displayed at the start of playback. Smile Shot When a smiling face is detected during motion picture recording, the unit automatically records a still picture.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 63 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Built-in flash When the button is pressed, the flash is activated and the picture will be recorded. Use the Built-in flash in order to record still pictures in dark places. The icon changes each time it is touched. ß ([ON]) # ßA ([AUTO]) # ([OFF]) ≥ The unit automatically determines if the flash is necessary even when it has been set to by detecting the ambient brightness.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 64 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Self-timer This is for recording still pictures using the timer. The icon changes each time it is touched. Ø10 (Records after 10 seconds) # Ø2 (Records after 2 seconds) # setting canceled ≥ When the button is pressed, a still picture is recorded after the Ø10 or Ø2 display and the recording lamp flashes for the time which has been set. After recording, the Selftimer is canceled.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 65 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Guidelines You can check if the image is level while recording or playing back motion pictures and still pictures. The function can also be used to estimate the balance of the composition. The icon changes each time it is touched. # # # Setting canceled ≥ It is possible to set from the quick menu. (l 42) ≥ The guidelines do not appear on the images actually recorded.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 66 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Recording) Recording functions of menus [SCENE MODE] When you record images in different situations, this mode automatically sets optimum shutter speeds and apertures.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 67 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ (Soft skin) j If the background or anything else in the scene has colors similar to the skin color, they will also be smoothed. j If the brightness is insufficient, the effect may not be clear. j If you record a person in the distance, the face may not be recorded clearly. In this case, cancel Soft Skin Mode or zoom in on the face (close-up) to record. ≥ (Fireworks) j The shutter speed is 1/30.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 68 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [REC MODE] Switch the picture quality and recording format of the motion pictures to be recorded. MENU : [RECORD SETUP] # [REC MODE] # desired setting ≥ It is possible to set from the quick menu. (l 42) [HA]/[HG]/[HX]/[HE]*1: Set the recording mode to 1080/60i. [1080/60p]*2: Set the recording mode to 1080/60p. [iFrame]*3: Set the recording mode to iFrame.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 69 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Setup example Setup time (recording interval) Recording time Recorded time Sunset 1s Approx. 1 h Approx. 2 min Blooming 30 s Approx. 3 h Approx. 12 s ≥ Maximum recordable time is 12 hours. ≥ Still picture recording cannot be used. ≥ Recording mode cannot be changed when the Interval Recording is set. ≥ If you turn off the unit or change the mode to , this function is canceled.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 70 ページ ２０１２年１月１１日 水曜日 午後１０時６分 touching [YES], but you will not be able to perform the [RELAY SCENE COMBINE] after that. ≥ Still pictures are recorded to the SD card after Relay Recording. ≥ is displayed on the thumbnail display during the playback of the scene that was relayrecorded on the built-in memory. [FACE RECOG.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 71 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Entering text ≥ The characters can be conveniently input without moving the cursor when the [Auto Cursor Position] is set to [ON]. (l 49) Icon [A] etc. / [A/a] Description of operation Enters a character. Moves the cursor to left or right. Switches between [A]/[a] (alphabet) and [&/1] (symbols/numbers). Enters a space. [Delete] Deletes a character. Deletes the previous character if the cursor is in an empty space.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 72 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Canceling a registered person 1 Select the menu. MENU : [RECORD SETUP] # [FACE RECOG.] # [SET] # [DELETE] or [DELETE ALL] ≥ Touching [DELETE ALL] cancels all the registered people. 2 (When [DELETE] is selected) Touch the person to cancel. ≥ When touched, the person is selected and touch again. ≥ Touch [ENTER]. is displayed.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 73 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Prioritized face framing Prioritized face framing is displayed as orange frames. Focus and adjustment of brightness will be performed against the prioritized face framing. ≥ Prioritized face framing is only displayed with Portrait Mode in the Intelligent Auto Mode. ≥ The white frame is for face detection only. ≥ Focus will be set to prioritized face framing when the button is pressed halfway when recording still pictures.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 74 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [Digital Cinema Color] Recording motion pictures with more vivid colors, using x.v.Color™ technology. ≥ Switch to Manual Mode. (l 83) ≥ Set [REC MODE] to [HA], [HG], [HX], [HE] or [1080/60p]. (l 68) MENU : [RECORD SETUP] # [Digital Cinema Color] # [ON] ≥ For more realistic colors, use an HDMI mini cable (optional) with a TV that supports the x.v.Color™.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 75 ページ ２０１２年１月１１日 水曜日 午後１０時６分 HC-X900M [MIC SETUP] Recording setting of the built-in microphone can be adjusted. MENU : [RECORD SETUP] # [MIC SETUP] # desired setting [SURROUND]: Sound is recorded with 5.1 ch surround microphone. [ZOOM MIC]: Sound is recorded with 5.1 ch surround microphone changing the directionality in conjunction with the zoom operation.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 76 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [MIC LEVEL] HC-X900M When recording, the input level from the built-in microphones and the external microphone terminal can be adjusted. HC-X800 When recording, the input level from the built-in microphones can be adjusted. 1 Select the menu. MENU : [RECORD SETUP] # [MIC LEVEL] # desired setting [AUTO]: [SETr AGC is activated, and the recording level is adjusted automatically. ]/[SET]: The desired recording level can be set.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 77 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ HC-X900M When [MIC SETUP] is [ZOOM MIC], the volume will be different depending on the zoom rate. HC-X800 When [ZOOM MIC] is [ON], the volume will be different depending on the zoom rate. ≥ HC-X900M When [MIC SETUP] is set to [STEREO MIC] or external microphone input is used, the sound is stereo (2 ch) and only the front-left and front-right input level meters function.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 78 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [ZEBRA] Parts where white saturation (color saturation) is likely to occur (extremely brightly lit or shiny parts) are displayed with diagonal lines (zebra pattern). ≥ Switch to Manual Mode. (l 83) MENU : [RECORD SETUP] # [ZEBRA] # [ON] ≥ It is possible to set from the quick menu in Manual Mode.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 79 ページ ２０１２年１月１１日 水曜日 午後１０時６分 MENU : [RECORD SETUP] # [HISTOGRAM] # desired setting ≥ It is possible to set from the quick menu in Manual Mode. (l 42) [ON ADJUST]: Display only when [IRIS] is adjusted. (l 85) [ALWAYS]: Constantly display. [OFF]: Cancel the setting. ∫ Example of the display A Normal B Dark C Bright [PICTURE SIZE] The higher the number of pixels, the higher the clarity of the picture when printing.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 80 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Picture size in Motion Picture Recording Mode ≥ Change the mode to . MENU : [PICTURE] # [PICTURE SIZE] # desired setting ≥ It is possible to set from the quick menu. (l 42) Picture size 14.7M 5120k2880 8.3 M 3840k2160 2.1 M 1920k1080 Aspect ratio [16:9] ≥ This function’s default settings are 16 M in Still Picture Recording Mode and 14.7M in Motion Picture Recording Mode.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 81 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [HI-SPEED BURST] Recording is done continuously at the rate of 60 still pictures per second. Use this function to record an object with fast movement. 1 Select the menu. MENU : [PICTURE] # [HI-SPEED BURST] # [ON] [ON]: 180 still pictures are recorded continuously at the rate of 60 per second. The picture size is 2.1 M (1920k1080). [OFF]: Cancel the setting. 2 Press the button. ≥ flashes in red during recording.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 82 ページ ２０１２年１月１１日 水曜日 午後１０時６分 [AF ASSIST LAMP] Illuminating the subject makes it easier for the camera to focus when recording in low light conditions that make focusing difficult. ≥ Switch to Manual Mode. (l 83) MENU : [PICTURE] # [AF ASSIST LAMP] # [AUTO] ≥ The available distance of the AF assist lamp is approx. 1.5 m (5 feet). ≥ A conversion lens (optional) can block the AF assist lamp, and it will become harder to adjust the focus.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 83 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Recording) Manual recording The operation sequence differs for the LCD monitor and viewfinder. ≥ The Manual Focus, White Balance, Shutter Speed, Brightness (Iris and Gain) settings are retained when you change between Motion Picture Recording Mode and Still Picture Recording Mode. ∫ To switch to Manual Mode HC-X900M Press the iA/MANUAL button or the CAMERA FUNCTION button to switch to Manual Mode.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 84 ページ ∫ ２０１２年１月１１日 水曜日 午後１０時６分 HC-X900M When using the viewfinder 1 Press the CAMERA FUNCTION button to select the desired item. ≥ Selected item changes whenever the CAMERA FUNCTION button is pressed. 2 Rotate the multi manual ring to select the setting and press the CAMERA FUNCTION button to enter the setting. MNL FOCUS WB SHTR IRIS ≥ Zoom operation cannot be done using the multi manual ring during setting.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 85 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ To set the White Balance manually 1 Select , fill the screen with a white subject. MNL 2 Touch and set the blinking . ≥ HC-X900M When using the viewfinder, press and hold the CAMERA FUNCTION button. ≥ When the screen turns black instantly and the display stops flashing and then lights constantly, the setting is complete. ≥ If the display continues flashing, the White Balance cannot be set. In this case, use other White Balance Modes.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 86 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ When the iris value is adjusted to brighter than OPEN, it changes to the gain value. ≥ To return to auto setting, press the iA/MANUAL button again. ≥ When setting both the shutter speed and the iris/gain value, set the shutter speed and then set the iris/gain value. Manual shutter speed adjustment ≥ When the shutter speed is set lower than 1/15 in the Still Picture Recording Mode, using a tripod is recommended.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 87 ページ 1 ２０１２年１月１１日 水曜日 午後１０時６分 (When MF assist function is used) Select the menu. MENU : [RECORD SETUP] # [MF ASSIST] # [ON] ≥ It is possible to set from the quick menu. (l 42) ≥ Touch 2 3 to display the Manual icon. Touch [FOCUS]. Touch [MF] to change to Manual Focus. ≥ MF appears on the screen. 4 HC-X900M FOCUS Adjust the focus by rotating the multi manual ring.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 88 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Recording) Recording 3D image With the 3D Conversion Lens (optional) attached, you can record lifelike and powerful 3D image. HC-X800 To view 3D image, a television that supports 3D is required. 3D image The image is an illustration. ≥ In the unit, the recordable 3D images are AVCHD 3D format or side-by-side format (2screen structure).
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 89 ページ 4 ２０１２年１月１１日 水曜日 午後１０時６分 Touch [EXIT] to end the adjustment. ≥ HC-X900M Display of the LCD monitor is switched to 3D. ≥ When re-attaching the 3D Conversion Lens or after an impact, etc., it is recommended that you perform the adjustment again. 5 (When recording motion pictures) Press the recording start/stop button to start recording. (l 33) ≥ Start recording after removing the Lens front cap.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 90 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Functions that cannot be used during 3D recording When recording with the 3D Conversion Lens, you cannot use certain functions.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 91 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Playback) Playback Operations Motion picture playback using operation icon For details on the basic playback operations, refer to page 39. Playback operation Playback display Operating steps Fast forward/ rewind playback Touch 5 during playback to fast forward. (Touch 6 to rewind.) ≥ The fast forward/rewind speed increases if you touch 5/6 again. (The display on the screen changes from 5 to .
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 92 ページ Playback operation Playback display During Playback Direct playback ２０１２年１月１１日 水曜日 午後１０時６分 Operating steps Touch the Direct playback bar or slide it while touching. ≥ The playback pauses temporarily and skips to the position touched or slid to while touching. ≥ Playback will start by releasing your touching or sliding finger. ≥ HC-X900M Direct playback bar cannot be operated with the remote control.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 93 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ When select [FACE], it will select the portion for which Face Recognition was performed from the scenes judged to be clearly recorded. This will then be displayed as a thumbnail. ≥ A portion judged to be clearly recorded will be detected and displayed in thumbnail if you select [HIGHLIGHT]. 3 (When [MINUTES] is selected) Touch / to set the time. ≥ It can be set up to a maximum of 60 minutes. ≥ Touch [ENTER].
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 94 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Zooming in on a still picture during playback (Playback zoom) You can zoom in by touching a still picture during playback. 1 Touch and hold the part you wish to zoom in on during still picture playback. ≥ The still picture is zoomed in the following order: k1 # k2 # k4. Touch and hold the screen to zoom in from the normal display to k2, Touch the screen to zoom in from k2 to k4.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 95 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Playback) Various playback functions Playing back motion pictures/still pictures by date The scenes or the still pictures recorded on the same day can be played back in succession. 1 2 Touch the date select icon. (l 29) Touch the playback date. ALL The scenes or the still pictures recorded on the date selected are displayed as thumbnails. 3 Touch the scene or the still picture to be played back.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 96 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Highlight Playback Part that was recognized as clearly recorded is extracted from a long recording, and it can be played back or stored in a short time with effects and music added. It is also possible to create an original Highlight Playback by checking your favorite scenes and setting up to extract those scenes. ≥ Highlight Playback cannot be used for iFrame scenes and scenes saved in MP4. 1 Touch .
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 97 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Setting up the custom effect It is possible to enjoy the Highlight Playback with your favorite effect by setting up the combination of an image effect and music. 1 2 3 Touch [CUSTOM]. Touch [EFFECT SETUP] or [MUSIC SELECT]. (When [EFFECT SETUP] is selected) Touch the desired effect. ≥ When [EFFECT SETUP] is changed, [MUSIC SELECT] will be set the same as [EFFECT SETUP].
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 98 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Scene setting 1 (Only when Highlight Playback is started from [ALL AVCHD]) Touch the recording format of the scene to play back. [1080/60p]/[1080/60i]/[AVCHD 3D]/[SbS 3D] 2 3 Touch [SELECT DATE] or [SELECT SCENES]. (When [SELECT DATE] is selected) Touch the date to be played back. ≥ A maximum of 7 days can be selected. ≥ When touched, the date is selected and surrounded by red. Touch the date again to cancel the operation.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 99 ページ ２０１２年１月１１日 水曜日 午後１０時６分 To clear the favorite scenes from the thumbnail display 1 Touch [Reset]. 2 Touch [RESET ALL] or [RESET SELECTED]. ≥ The check on all the favorite scenes will be cleared when [RESET ALL] is selected. 3 4 (When [RESET SELECTED] is selected in step 2) Touch the scene to be cleared. Touch [YES]. ∫ Playing back the favorite scenes Touch [ON] or [OFF].
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 100 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Setting up the title 1 Touch / and select your favorite title sheet. [NONE]/[PICTURE 1]/[PICTURE 2]/[PICTURE 3]/[PICTURE 4] ≥ Title and date will not be displayed when [NONE] is selected. 2 3 Touch [TITLE]. Enter the title. ≥ Input method is same operation as for the face recognition. (l 70) ≥ Touch [Enter] after entering the title. ≥ A maximum of 18 characters can be entered. 4 Touch [ENTER] to end registration.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 101 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Changing the playback settings and playing back the slide show 1 Touch 2 (Only when you would like to change the settings) . (l 29) ALL Touch [SET] to select the item to change. [DATE SETUP]: [PLAYBACK SETUP]: [SLIDE INTERVAL]: [EFFECT SETUP]: [MUSIC SELECT]: 3 Select the date to be played back.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 102 ページ ２０１２年１月１１日 水曜日 午後１０時６分 (To test the music audio) Touch [START] and start the audio testing. ≥ Touch the other music option to change the music to be tested. ≥ When you touch [STOP], the music playback stops. 4 5 Touch [START]. Select the playback operation. (l 39) ≥ When the playback is finished or stopped, the screen to select [REPLAY], [SELECT AGAIN] or [EXIT] is displayed. Touch the desired item.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 103 ページ ２０１２年１月１１日 水曜日 午後１０時６分 (When [SINGLE] is selected in Step 2) Touch the scene/still picture to be deleted. ≥ Touched scene or still picture is deleted. 4 (When [MULTI] is selected in Step 2) Touch [Delete]. ≥ To continuously delete other scenes/still pictures, repeat Steps 3-4. When you stop deleting halfway Touch [CANCEL] while deleting. ≥ The scenes or still pictures that have already been deleted when the deletion is canceled cannot be restored.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 104 ページ 5 ２０１２年１月１１日 水曜日 午後１０時６分 Touch [YES] and confirm (play back) the edited scene. ≥ When [NO] is touched, a confirmation message appears. Proceed to Step 7. 6 Stop the playback. ≥ A confirmation message appears. 7 Touch [ENTER]. ≥ To continue deleting parts from other scenes, repeat Steps 2-7. ≥ Deleting a part of a scene cannot be performed when there are 99 scenes in a single date.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 105 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ If personal information in the divided scenes is deleted, the personal information is deleted when the divided scenes are canceled. Dividing a scene to partially delete (iFrame/MP4) Divide the iFrame scenes or scenes saved in MP4, and delete unnecessary parts. This divides the recorded scenes in two and deletes the front half or back half. The scenes that were deleted after division cannot be recovered.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 106 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Deleting personal information Deletes Face Recognition information from scenes in which faces were recognized. ≥ Change the mode to and touch the play mode select icon. Then, select the AVCHD scene. (l 39) ≥ Face Recognition information is not recorded in the scenes recorded in iFrame or the scenes saved as MP4. 1 Select the menu.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 107 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Playback) Relay scene combining [HC-X900M] You can combine the relayed scene (l 69) in the built-in memory and the continued scene in the SD card to be one into the SD card. ≥ Change the mode to AVCHD scene. (l 39) 1 2 Insert the SD card that was used for Relay Recording. Select the menu. MENU 3 and touch the play mode select icon.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 108 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Playback) Watching Video/Pictures on your TV Confirm the terminals on your TV and use a cable compatible with the terminals. Image quality may vary with the connected terminals. A High quality 1 HDMI terminal 2 Component terminal 3 Video terminal ≥ Use the AV multi cable (supplied) or HDMI mini cable (optional) and check the output settings. (l 110, 111) ≥ HDMI is the interface for digital devices.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 109 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ Check that the plugs are inserted as far as they go. ≥ Always use a genuine Panasonic HDMI mini cable (RP-CDHM15, RP-CDHM30: optional). ≥ Do not use any other AV multi cables except the supplied one. ≥ When connecting to the component terminal of the TV, the yellow plug of the AV multi cable is not required. ≥ When connecting to the AV terminal of the TV, do not connect the component terminal plug of the AV multi cable.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 110 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ To display the on-screen information on the TV HC-X900M STOP When the EXT DISPLAY button on the remote control is pressed, the information displayed on the screen (operation icon and time code etc.) can be displayed/not displayed on the TV. ≥ It will not display when the unit is turned off.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 111 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Listening in 5.1 channel sound (AVCHD) [HC-X900M] You still can listen to the 5.1 channel sound recorded from the internal microphones when this unit is connected to the 5.1 channel compatible AV amplifier or TV using the HDMI mini cable. Please read the AV amplifier and TV operating instructions for how to connect this unit to the AV amplifier and TV.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 112 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Playback) Playback using VIERA Link™ What is the VIERA Link (HDAVI Control™)? ≥ VIERA Link™ is a new name for EZ Sync™. ≥ This function allows you to use your remote control for the Panasonic TV for easy operations when this unit has been connected to a VIERA Link compatible device using a HDMI mini cable (optional) for automatic linked operations. (Not all operations are possible.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 113 ページ 3 ２０１２年１月１１日 水曜日 午後１０時６分 Operate with the remote control for the TV. 1) 2) 1) Press the button up, down, left or right to select a scene or still picture to be played back, and then press the button in the center to set it. 2) Activate the operation icons that are displayed on TV screen with the remote control for the TV.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 114 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Advanced (Playback) 3D image playback [HC-X900M] The scenes or still pictures recorded in 3D can be played back as 3D image on the LCD monitor of this unit, or by connecting this unit to the 3D compatible TV. It is also possible to convert the scenes and still pictures recorded in 2D to 3D and play back.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 115 ページ 3 ２０１２年１月１１日 水曜日 午後１０時６分 (When playing back scenes or still pictures on the 3D compatible television compatible to the frame sequential format) Select the menu. MENU : [SETUP] # [3D OUTPUT] # [HDMI] [HDMI]: The scenes recorded in AVCHD 3D are displayed on TV as 3D full high definition image. [LCD]: 3D image is displayed on the LCD monitor of this unit and the 3D compatible TV.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 116 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ It will be played back in 2D display for following cases: j Connect the AV multi cable to the video terminal of the TV j When [COMPONENT OUT] is set to [480i] and the AV multi cable is connected to the component terminal of the TV ≥ When you play back scenes successively, a black screen will appear for a few seconds between scenes recorded in 3D and scenes recorded in 2D.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 117 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Converting and playing back 2D (3D) images as 3D (2D) Scenes and still pictures recorded in 2D (3D) can be converted and played back as 3D (2D). ¬ Change the mode to and touch the play mode select icon. Then, select the AVCHD scene or set to . (l 39) 1 Touch the 2D/3D display icon ( ). (l 29) / / ≥ This is not displayed when playing back the iFrame scenes or scenes saved in MP4. ≥ It is possible to set from the menu.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 118 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Adjusting 3D effect of the 3D image It is possible to adjust the disparity of the scenes and still pictures playing back in 3D for better view. 1 2 Play back scenes or still pictures recorded in 3D. Touch . ≥ Playback disparity adjustment bar is displayed while displaying in 3D. 3 Touch / to adjust setting. ≥ Playback disparity adjustment bar will disappear after approx. 5 seconds without any touch operation.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 119 ページ 2 ２０１２年１月１１日 水曜日 午後１０時６分 (When playing back scenes or still pictures on the 3D compatible television compatible to the frame sequential format) Connect this unit to the 3D compatible television using an HDMI mini cable (optional). (l 108) ≥ The scene recorded in AVCHD 3D is played back in 3D full high-definition image.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 120 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Converting and playing back 2D images as 3D You can connect this unit to 3D compatible TV, convert the scenes and still pictures recorded in 2D (conventional image) to 3D and play back. ¬ Change the mode to and touch the play mode select icon. Then, select the AVCHD scene or set to . (l 39) MENU : [VIDEO SETUP] or [PICT. SETUP] # [CONV. 2D TO 3D] # [ON] [ON]: Convert and play back the images recorded in 2D as 3D images.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 121 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Copy/Dubbing Copying between SD card and Built-in Memory [HC-X900M] Motion pictures or still pictures recorded with this unit can be copied between an SD card inserted in this unit and a built-in memory. ∫ Check the used space of the copy destination It is possible to check the used space of the SD card or built-in memory by [MEDIA STATUS] (l 51).
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 122 ページ 3 ２０１２年１月１１日 水曜日 午後１０時６分 Touch desired items following the screen display. ≥ It will return to the previous step by touching . ≥ (When [SELECT SCENES] is selected) When touched, the scene/still picture is selected and the indication appears on the thumbnail. Touch the scene/still picture again to cancel the operation. ≥ (When [SELECT DATE] is selected) When touched, the date is selected and surrounded by red. Touch the date again to cancel the operation.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 123 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ Motion pictures that have been recorded on another device may not be copied. Data recorded on a PC with HD Writer AE 4.1, etc. cannot be copied. ≥ Protection settings will be cleared on the copied motion pictures and still pictures when copying motion pictures and still pictures with protection settings. ≥ The order in which the scenes or still pictures were copied cannot be changed.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 124 ページ 1 ２０１２年１月１１日 水曜日 午後１０時６分 Connect the AC adaptor (supplied with DVD burner) to the DVD burner. ≥ You cannot supply power to the DVD burner from this unit. 2 3 Connect this unit to the AC adaptor and change the mode to Connect this unit to the DVD burner with the USB Connection Cable (supplied with DVD burner). A USB Connection Cable (supplied with DVD burner) B DVD burner (optional) ≥ Insert the plugs as far as they will go.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 125 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Copying to discs ≥ You cannot copy from multiple SD cards to 1 disc. (You can additionally copy only to a DVD-RAM.) ≥ You cannot copy motion pictures together with still pictures or motion pictures in a different picture quality (AVCHD picture quality and conventional normal picture quality) to the same disc. ≥ iFrame scenes or scenes saved in MP4 cannot be copied to disc. Copy to PC to make a backup.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 126 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Important Notice ≥ When connecting an optional DVD burner and this unit for copying a disc, do not insert a disc with recorded motion pictures in high-definition picture quality into devices that do not support the AVCHD format. In some cases the disc may get stuck in the device. The disc will not play back on devices that do not support the AVCHD format.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 127 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ The disc that was copied to can be played back by connecting this unit and a DVD burner. ≥ Do not turn off this unit or the DVD burner or disconnect the USB Connection Cable while copying. Also, do not shake this unit or the DVD burner. ≥ It is impossible to stop copying halfway. ≥ The order in which the scenes were copied cannot be changed. ≥ Data that has been recorded on another device may not be copied.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 128 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Managing the copied disc ≥ Connect this unit to the DVD burner and then touch [PLAY DISC]. (l 124) ∫ Formatting discs This is for initializing DVD-RAM, DVD-RW and +RW discs. Please be aware that if a disc is formatted, then all the data recorded on the disc will be erased. Back up important data on a PC etc. MENU : [DISC SETUP] # [FORMAT DISC] ≥ When formatting is complete, touch [EXIT] to exit the message screen.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 129 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Copy/Dubbing Dubbing with a Blu-ray disc recorder, video devices, etc. ∫ Check before dubbing Check the equipment used for dubbing.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 130 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Dubbing in high-definition picture quality You can dub using a Panasonic Blu-ray disc recorder or high-definition (AVCHD) compatible DVD recorder. ≥ Depending on the recorders or the media to be copied to, you may not be able to copy in high-definition (AVCHD) picture quality. For further details, see the operating instructions of your recorder. ≥ Note that the equipment described may not be available in certain countries and regions.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 131 ページ 2 ２０１２年１月１１日 水曜日 午後１０時６分 Touch [RECORDER] on the screen of this unit. ≥ When you select an option other than [RECORDER], reconnect the USB cable. ≥ HC-X800 When using the battery, the LCD monitor turns off after about 5 seconds. Touch the screen to turn the LCD monitor on. 3 HC-X900M Touch the media you wish to dub. ≥ When using the battery, the LCD monitor turns off after about 5 seconds. Touch the screen to turn the LCD monitor on.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 132 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Dubbing in standard picture quality ∫ Dubbing using equipment without an SD card slot or a USB terminal, or using a video device You can dub by connecting an AV multi cable. ≥ Images are dubbed in standard quality. ≥ Use the AC adaptor to free you from worrying about the battery running down. Change the video input on the video device and TV that this unit is connected to.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 133 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Copy/Dubbing 3D image storage You can store 3D image with a DVD burner, a video device or a PC. Copying with a DVD burner ≥ Please refer to page 123 for details about copying with a DVD burner. ∫ Copying unaltered as 3D images Recording format: [High Definition] ≥ Scenes recorded in [AVCHD 3D] are converted, copied, and saved as 2D image. Image will be recorded in 1080/60i picture quality.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 134 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Dubbing in standard picture quality ≥ Please refer to page 132 for details about dubbing in standard picture quality. Copying unaltered as 3D motion picture HC-X900M When [2D/3D DISPLAY] is [2D/3D] or [3D], the 3D motion picture is recorded in side-by-side format.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 135 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Using HD Writer AE 4.1 ≥ Please refer to page 136 for details about copying with HD Writer AE 4.1. When you use HD Writer AE 4.1 to handle scenes recorded in 3D, the following operations are possible. j Copying data to a PC (Scenes recorded in 3D will be copied unaltered as 3D motion picture.) j Copying in Blu-ray disc or AVCHD format (Scenes recorded in 3D will be copied unaltered as 3D motion picture.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 136 ページ ２０１２年１月１１日 水曜日 午後１０時６分 With a PC What you can do with a PC HD Writer AE 4.1 You can copy the motion/still picture data to the HDD of PCs or write to media like Blu-ray discs, DVD discs or SD cards using HD Writer AE 4.1, the software installed in the supplied CD-ROM. Refer to the operating instructions of HD Writer AE 4.1 (PDF file) for details on how to use it.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 137 ページ ２０１２年１月１１日 水曜日 午後１０時６分 What can be done with the HD Writer AE 4.1 Data type Playing back on a PC: Play back the motion picture data in high-definition picture quality on a PC. Motion picture and still picture Formatting discs: Depending on the type of disc that you use, formatting is necessary.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 138 ページ ２０１２年１月１１日 水曜日 午後１０時６分 End User License Agreement Before opening the CD-ROM package, please read the following. You (“Licensee”) are granted a license for the Software defined in this End User License Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 139 ページ ２０１２年１月１１日 水曜日 午後１０時６分 With a PC Operating environment ≥ Even if the system requirements mentioned in this owner’s manual are fulfilled, some PCs cannot be used. ≥ A CD-ROM drive is necessary to install the supplied software applications. (A compatible Blu-ray disc/DVD writer drive and media are necessary for writing to a Blu-ray disc/DVD.) ≥ Operation is not guaranteed in the following cases.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 140 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Display High Color (16 bit) or more (32 bit or more recommended) Desktop resolution of 1024k768 pixels or more (1920k1080 pixels or more recommended) Windows 7/Windows Vista: DirectX 9.0c compatible video card (DirectX 10 recommended) Windows XP: DirectX 9.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 141 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ To use the HD Writer AE 4.1 You will need a high performance PC depending on the functions to be used. It may not properly play back or properly operate depending on the environment of the PC used. Refer to the operating environment and notes. ≥ Operation during the playback may become slow if the CPU or memory is not fulfilling the requirements of the operating environment. ≥ Always use the most current driver for the video card.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 142 ページ ２０１２年１月１１日 水曜日 午後１０時６分 With a PC Installation When installing the software, log on to your computer as the Administrator or with a user name with equivalent authorization. (If you do not have authorization to do this, consult your manager.) ≥ Before starting the installation, close all applications that are running. ≥ Do not perform any other operations on your PC while the software is being installed. ≥ Explanation of operations is based on Windows 7.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 143 ページ 1 ２０１２年１月１１日 水曜日 午後１０時６分 Connect this unit to the AC adaptor. ≥ Use the AC adaptor to free you from worrying about the battery running down. ≥ Connect with the AC adaptor when using the Conversion Assist Function. 2 Turn on the unit. ≥ This function is available in all modes. 3 Connect this unit to a PC. ≥ The USB function selection screen will appear. 4 Touch [PC] on the screen of this unit.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 144 ページ ２０１２年１月１１日 水曜日 午後１０時６分 About the PC display When the unit is connected to a PC, it is recognized as an external drive. ≥ Removable disk (Example: ) is displayed in [Computer]. We recommend using HD Writer AE 4.1 to copy motion picture data. Using Windows Explorer or other programs on the PC to copy, move or rename files and folders recorded with this unit will result in them being unusable with HD Writer AE 4.1.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 145 ページ ２０１２年１月１１日 水曜日 午後１０時６分 With a PC Starting HD Writer AE 4.1 ≥ To use the software, log on as an Administrator or as user name for standard user account (only for Windows 7/Windows Vista). The software cannot be used with the user name for a guest account. (On the PC) Select [Start] # [All Programs] # [Panasonic] # [HD Writer AE 4.1] # [HD Writer AE].
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 146 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ∫ Operating environment PC OS CPU RAM Interface Other requirements Mac Mac OS X 10.7.2 Intel Core 2 Duo or better 2 GB or more USB port Mouse or equivalent pointing device ≥ Even if the system requirements mentioned in this owner’s manual are fulfilled, some PCs cannot be used. ≥ The USB equipment operates with the driver installed as standard in the OS. ≥ Supplied CD-ROM is available for Windows only.
HC-X900M&X800P&PC&PU-VQT4C76_mst.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 148 ページ 15.1M / 8.6M / 5.8M / 0.3M / 16 M / 8.6M / 6.1M / 14.7M / 8.3 M / 5.8 M / 2.1 M / 0.2 M ２０１２年１月１１日 ± (White)/¥ (Green)/ 水曜日 / / 午後１０時６分 / / Focus indication (l 35) Number of recording pixels for still pictures (l 36, 79, 81, 92) High-Speed Burst Shooting (l 81) In Playback Mode, the picture size is not displayed for still pictures recorded with other products that have different picture sizes from the sizes shown above.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 149 ページ ∫ Playback indications 1/;/5/ /6/ D/E/;1/2; /7/8/9/:/ ２０１２年１月１１日 Playback Time (l 39) No.10 Scene Number Accessing the card (l 131, 143) Accessing the built-in memory (l 131, 143)*1 Repeat Playback (l 93) Resume Playback (l 93) 100-0001 Still picture folder/file name ∫ Confirmatory indications –– (Time display) The built-in battery is low.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 150 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Messages Major confirmation/error messages to be indicated on the screen in text. * HC-X900M only PERIODICALLY MAKE BACK UP OF DATA IN BUILT-IN MEMORY.* We recommend backing up important recorded motion pictures and still pictures periodically to a PC, DVD disc, etc. to protect it. (l 123, 136) This message does not indicate that there is a problem with this unit. CHECK CARD.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 151 ページ ２０１２年１月１１日 水曜日 午後１０時６分 ≥ If recovery fails, turn the unit off and on again after waiting awhile. If recovery fails repeatedly, format a media on the unit. Please be aware that if a media is formatted, then all the data recorded on the media will be erased. ≥ If the thumbnail information is recovered, displaying the thumbnails may become slower.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 152 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Power Problem This unit cannot be operated though it is turned on. This unit does not operate normally. “ERROR OCCURRED. PLEASE TURN UNIT OFF, THEN TURN ON AGAIN.” is displayed. Check points ≥ Remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the unit again.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 153 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Recording Problem Check points Color balance of images is strange when recording in a place such as a gymnasium. ≥ In a place with multiple light sources, such as a gymnasium or a hall, set the White Balance setting to (Indoor mode 2). If you cannot record clearly with the (Indoor mode 2), set it to (Manual adjustment mode). (l 84) Color or brightness of the image changes, or you may see horizontal bars in the image.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 154 ページ ２０１２年１月１１日 水曜日 午後１０時６分 With other products Problem VIERA Link does not work. Check points (Setting on this unit) ≥ Connect with a HDMI mini cable (optional). (l 112) ≥ Touch MENU , then touch [SETUP] # [VIERA Link] # [ON]. (l 112) ≥ Turn the unit off and then back on again. (Setting on other devices) ≥ If the TV input does not switch automatically, switch the input using the TV remote control. ≥ Check the VIERA Link setting on the connected device.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 155 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Problem Check points If the SD card is inserted in this unit, it is not recognized. ≥ If the SD card is formatted on a PC, it may not be recognized by this unit. Use this unit to format SD cards. (l 50) HC-X900M The remote control does not function. ≥ [REMOTE CONTROL] of the [SETUP] is [OFF]. (l 52) ≥ The button-type battery of the remote control may be run out. Replace it with a new button-type battery.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 156 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Cautions for use About this unit The unit and the SD card become warm during use. This is not a malfunction. Keep this unit as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). ≥ If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be disrupted by electromagnetic wave radiation.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 157 ページ Do not use the unit for surveillance purposes or other business uses. ≥ This unit was designed for consumer intermittent use. It was not intended for continuous use, or for any industrial or commercial application resulting in prolonged use. ≥ In certain situations, continuous use could cause the unit to overheat and cause a malfunction. Such use is strongly discouraged.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 158 ページ Prepare spare batteries when going out for recording. ≥ Prepare batteries enough to last for 3 to 4 times the period you are planning to record for. Cold places such as a ski resort can shorten recording time. If you drop the battery accidentally, check to see if the terminals are damaged. ≥ Attaching a battery with damaged terminals can damage the unit. Do not throw old battery into fire.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 159 ページ About 3D About 3D recording Attach the 3D Conversion Lens securely. It must not be used with an insecure attachment. Do not use the 3D Conversion Lens without adjusting it first. ≥ It will not be possible to record 3D image correctly, and this may lead to tiredness or discomfort. ≥ When you re-attach the 3D Conversion Lens after removing it, we recommend making the adjustments again.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 160 ページ About the SD card When disposing of or giving away the SD card, note that: ≥ Formatting and deletion of data on this unit or computer only changes the file management information and does not completely delete the data in the SD card. ≥ It is recommended that the SD card is physically destroyed or the SD card is physically formatted using this unit when disposing of or giving away the SD card.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 161 ページ HC-X800 Extremely high precision technology is employed to produce the LCD Monitor screen featuring a total of approximately 460,000 dots. The result is more than 99.99% effective dots with a mere 0.01% of the dots inactive or always lit. However, this is not a malfunction and does not affect the recorded picture.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 162 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others About copyright ∫ Carefully observe copyright laws Whatever you have recorded and created can be used for your personal entertainment only. Under copyright laws, other materials cannot be used without obtaining permission from the holders of the copyrights. ∫ Licenses ≥ SDXC Logo is a trademark of SD-3C, LLC.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 163 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Recording modes/approximate recordable time ≥ SD cards are only mentioned with their main memory size. The stated times are the approximate recordable times for continuous recording.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 164 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Approximate number of recordable pictures ≥ SD cards are only mentioned with their main memory size. The stated number is the approximate number of recordable pictures. Picture size 15.1M 8.6M 5.8M 0.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 165 ページ ２０１２年１月１１日 水曜日 午後１０時６分 When recording 3D still picture Picture size Aspect ratio 4 GB SD card 16 GB 64 GB 2.1 M 1920k1080 [16:9] 1000 4300 17500 HC-X900M Built-in memory 32 GB 8500 ≥ The number of recordable pictures depends on the subject being recorded. ≥ When recording a 3D still picture, the equivalent 2D still picture is recorded as well; therefore, the number of recordable pictures will be reduced accordingly.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 166 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Specifications High Definition Video Camera Information for your safety Power source: DC 9.3 V (When using AC adaptor) DC 7.2 V (When using battery) Power consumption: Recording; HC-X900M 8.9 W HC-X800 7.9 W Charging; HC-X900M 10.3 W HC-X800 10.1 W Motion picture recording format: [AVCHD]; AVCHD format version 2.0 compliant (AVCHD 3D/Progressive) [iFrame]; MPEG-4 AVC file format compliant (.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 167 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Recording media: SD Memory Card (FAT12 and FAT16 system compliant) SDHC Memory Card (FAT32 system compliant) SDXC Memory Card (exFAT system compliant) Refer to page 24 for details on SD cards usable in this unit. HC-X900M Built-in memory; 32 GB Image sensor: 1/4.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 168 ページ ２０１２年１月１１日 Speaker: 1 round speaker, dynamic type White balance adjustment: Auto tracking white balance system Standard illumination: 1,400 lx Minimum required illumination: Approx. 1.6 lx (1/30 with Low Light mode in the Scene Mode) Approx. 1 lx with the Color Night Rec function AV multi connector video output level: Component video out put level; Y; 1.0 Vp-p, 75 h Pb; 0.7 Vp-p, 75 h Pr; 0.7 Vp-p, 75 h AV video output level; 1.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 169 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Mass (Weight): HC-X900M Approx. 425 g (Approx. 0.93 lbs.) [without battery (supplied)] HC-X800 Approx. 345 g (Approx. 0.76 lbs.) [without battery (supplied) and an SD card (optional)] Mass (Weight) in operation: HC-X900M Approx. 485 g (Approx. 1.06 lbs.) [with battery (supplied)] HC-X800 Approx. 405 g (Approx. 0.89 lbs.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 170 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Optional accessories Accessory No. Figure Description VW-BC20PP Battery charger VW-VBN130*1 Rechargeable Lithium Ion Battery Pack VW-VBN260*1 Rechargeable Lithium Ion Battery Pack RP-CDHM15 RP-CDHM30 HDMI mini cable VW-W4907H*2 Wide conversion lens VW-CLT2*2 3D Conversion Lens VW-LF49N*2 Filter kit *1 Please refer to page 22, concerning the battery charging time and available recording time.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 171 ページ Accessory No.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 172 ページ ∫ HC-X900M Attaching the optional accessories on the shoe adaptor 1 Open the shoe adaptor cover. 2 Attach the shoe adaptor to this unit. ≥ Attach the optional accessories to the shoe adaptor. ≥ When removing the shoe adaptor, slide the SHOE ADAPTOR RELEASE lever, and remove the shoe adaptor while sliding the lever.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 173 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Accessory Order Form (For USA and Puerto Rico Customers) Please photocopy this form when placing an order. 1. Model # 2. Items Ordered Accessory # Description Price Each Quantity Total Price Shipping & Handling $6.95 Subtotal Your State & Local Sales Tax Total 3. Method of payment (check one) American Express VISA Credit Card # MasterCard Expiration Date Discover Customer Signature (Please do not send cash) 4.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 174 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Limited Warranty (ONLY FOR U.S.A.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 175 ページ ２０１２年１月１１日 水曜日 午後１０時６分 THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 176 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Warranty (For Canadian Customers) Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 177 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Others Useful Information (Only For Latin American Countries) Customer Service Customer Service Directory Obtain product information and operative assistant; localize the closer distributor or Service Center; buy spare parts and accessories by our web site to Latin American: http://www.lar.panasonic.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 178 ページ Index ∫ Numerics 1080/60p recording . . . . . . . . . . . . . . . 56 2D/3D display . . . . 89, 114, 116, 117, 120, 134 3D Conversion Lens setup . . . . . . . . . . 88 3D image storage . . . . . . . . . . . . . . . 133 3D output . . . . . . . . . . . . . . . . . . . . . 115 3D playback/viewing . . . . . 114, 118, 159 3D recording . . . . . . . . . . . . . . . . 88, 159 5.1 channel . . . . . . . . . . . . . . . . . . . . 111 ∫ A AC adaptor . . . . . . . . . . . .
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 179 ページ ∫ L Language . . . . . . . . . . . . . . . . . . . . . . 51 LCD monitor . . . . . . . . . . . . . 17, 31, 160 LCD set . . . . . . . . . . . . . . . . . . . . . . . . 48 Lens cap . . . . . . . . . . . . . . . . . . . . . . 172 Lens hood . . . . . . . . . . . . . . . . . . . . . . 31 Limited Warranty (Canada) . . . . . . . . 176 Limited Warranty (USA and Puerto Rico) . . . . . . . . . . . 174 Luminance . . . . . . . . . . . . . . . . . . . . .
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 180 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Spanish Quick Use Guide/Guía española para el uso rápido ∫ Insertar la batería Abra el monitor LCD y coloque la batería introduciéndola en la dirección mostrada en la figura. ∫ Insertar/extraer una tarjeta SD ≥ Introduzca la batería hasta que haga clic y se cierre. ∫ Carga de la batería A Terminal de entrada de CC 1 Conecte el cable de CA al adaptador de CA, luego a la toma de CA.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 181 ページ ∫ Encender/apagar el dispositivo Encender y apagar el dispositivo con el botón de alimentación Abra el monitor LCD y presione el botón de alimentación para encender la unidad ２０１２年１月１１日 水曜日 午後１０時６分 Para apagar la unidad HC-X900M HC-X800 HC-X900M B El indicador de estado se apaga. HC-X800 ∫ Selección del modo Utilizando el interruptor de modo, cambie el modo a , o . HC-X900M A El indicador de estado se ilumina.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 182 ページ ∫ Cómo usar la pantalla táctil Puede actuar directamente tocando el monitor LCD (pantalla táctil) con el dedo. Toque Toque y suelte la pantalla táctil para seleccionar el icono o la imagen. 水曜日 午後１０時６分 ∫ Seleccionar un medio para grabar HC-X900M 1) 2) Cambie el modo a Seleccione el menú. oa . : [SELEC MEDIO] MENU 3) Deslice mientras toca Mueva el dedo mientras pulsa la pantalla táctil.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 183 ページ 4) ∫ Reproducción de película/ fotografía 1) 2) Cambie el modo a . Toque el icono de selección del modo de reproducción A. ALL 3) HC-X900M Seleccione el tipo de medio D y a continuación la imagen fija B o el formato de grabación de la imagen en movimiento C que desee reproducir. ２０１２年１月１１日 水曜日 午後１０時６分 Toque la escena o la fotografía que desea reproducir.
HC-X900M&X800P&PC&PU-VQT4C76_mst.book 184 ページ ２０１２年１月１１日 水曜日 午後１０時６分 Panasonic Consumer Marketing Company of North America, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 Panasonic Canada Inc.
