Datasheet

197
Digital Fiber Sensor FX-300 SERIES
Selection
Guide
Fibers
Ampliers
FX-500
FX-100
FX-300
FX-410
FX-311
FX-301-F7/
FX-301-F
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
PLC /
TERMINALS
HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
PRECAUTIONS FOR PROPER USE
Refer to General precautions, p.80~ for ber precautions, and to the “PRO mode operation
guide” on our website for details pertaining to operating instructions for the amplier.
Cautions on sensor connection in cascade
• When the units of the group A and the group B are
connected in cascade as <Figure B> shown above,
optical communications cannot be done. When the
optical communications function is used, connect them as
<Figure A> shown above. If the units cannot be placed
as <Figure A>, the following measure
1
or
2
should be
taken.
1
Afx the communication window seal of the accessory
ber amplier protection seal (FX-MB1) to the
communication window of the FX-301(P) updated
version unit or FX-305(P).
2
If the measure
1
described above cannot be taken,
change the optical communications spec. of the group B
units.
• When the units in the group A and the group B shown in
the table below are connected in cascade, connect them
in cascade as <Figure A> shown below.
Group B
Group A
<Figure A>
Group A
Group B
<Figure B>
Optical communications
are possible
Optical communications
are impossible
Group A
FX-301(P): Previous version unit
(Note 1), FX-301G(P)/B(P)/H(P),
FX-41
□(P), LS-401(P) (Note 2)
Group B
FX-301(P): Updated version
unit (Note 1), FX-305(P)
Notes: 1) For the difference between the updated
version unit and the previous version
unit, refer to “A difference between the
updated version unit and the previous
version unit”.
2)
When LS-401(P) is connected with the
digital ber amplier in cascade, be sure to
locate LS-401(P) at the left-most position
(when viewed from the connector side).
Notes: 1) FX-305(P); Output 1 operation indicator (Orange)
2) FX-305(P); Output 2 operation indicator (Orange)
MODE indicator / L/D ON (Yellow)
MODE indicator / TIMER (Yellow)
MODE key
Jog switch
MODE indicator /
PRO (Yellow)
Digital display (Red)
MODE indicator / ADJ (Yellow)
MODE indicator / TEACH (Yellow)
MODE indicator / RUN (Green)
Operation indicator (Orange) (Note1)
Stability indicator
(Green)(Note2)
Mount the ampliers, one by
one, on the 35 mm 1.378 in
width DIN rail.
Slide the ampliers next to each
other, and connect the quick-
connection cables.
Mount the optional end plates
(MS-DIN-E) at both the ends to
hold the ampliers between
their at sides.
Tighten the screws to x the
end plates.
• Change the communication specication of Group B
according to the following procedures. Make sure to set the
communication specication to “
(Group A communication
specication)” or “
(Optical Communication Stop)”.
Dismantling
Cascading method How to change the communication specication of Group B
Loosen the screws of the end
plates.
Remove the end plates.
Slide the ampliers and remove
them one by one.
35 mm 1.378 in
width DIN rail
Sub unit
Main unit
Slide
Sub cable
(CN-71/72-C□)
(Optional)
Main cable
(CN-73/74-C□)
(Optional)
End plate
(MS-DIN-E)
(Optional)
Slide
Notes: 4) When the communication specication is set to “ (Group A
communication specication)”, make sure to tightly attach the
products. Also make sure to take note of the following:
• There are instances when the optical communication function
cannot be used due to the usage environment, etc.
• Do not perform batch channel loading or saving.
Group B's Communication
Specification
Group A's Communication
Specification
Optical Communication Stop
<Changing Procedure>
Display [PRO4].
Long press the [Jog Switch] and
[MODE key] at the same time.
(Note 3)
When you release the [Jog Switch] and
[MODE key], the communication specication
will be set and “PRO4” will be displayed.
Notes: 3) Every time the [Jog Switch] and the [MODE key] is
simultaneously long pressed, the display changes in
this sequence: “
”→“ ”→“ ”→“ ”→“ ”.
Part description
Operation procedure
Power ON
Communication self-check
RUN
TEACH
ADJ
L/D
TIMER
PRO
Press
MODE key
Press
MODE key
Press
MODE key
Press
MODE key
Press
MODE key
Press
MODE key
[Teaching]
(P.198)
[Threshold
value ne
adjust] (P.199)
[PRO mode]
(P.202)
[Timer operation
setting]
(P.199)
[Output operation
setting]
(P.199)
• When the power supply is switched on, communication
self-check is carried out and normal condition is
displayed [MODE indicator / RUN (green)] lights up and
the digital display shows the incident light intensity.
• When the MODE key is pressed, the mode will change as
shown in the following diagram.
When Jog switch is pressed, the setting is conrmed.
When MODE key is pressed for 2 sec., or more, the sensor returns to the ‘RUN’ mode.
Cancellation is possible by pressing MODE key during setting.