Panasonic Ventilating Fan INSTALLATION INSTRUCTIONS Model No. FV-08VQL5 F-11vQLs F-15vVQL5 READ AND SAVE THESE INSTRUCTIONS Thank you very much for having purchased our Ventilating Fan. Please read these instructions carefully before attempting to install, operate or service the Panasonic Ventilating Fan. Failure to comply with instructions could result in personal injury and/or property damage.
UNPACKING Unpack and carefully remove the unit from carton. Refer to the Supplied Accessories list to verify that all parts are present. SUPPLIED ACCESSORIES Part name Appearance Quantity Part name Appearance Quantity Screw II (ST4.2X14) er» 1 Rifle 1 Long screw (5T4.2X20) £2 5 Suspension ED 4 bracket I = 3aw Fluorescent xX: Q 1 Suspension = tamp 3 bracket Suspension 3 Night lamp & i bracket 1 1 Suspension pe 3 Installation 2 bracket IV instructions Screw I Warranty = (ST4.
GENERAL SAFETY INFORMATION . Do not install this ventilating fan where interior room temperature may exceed 04°F Make sure that the electric service supply voltage is AC 120V, 60H. Prohibited Follow all local electrical and safety codes, as well as the National Electrical Code {NEC) and the Occupation Safety and Health Act (OSHA). ay 4, Always disconnect the power source before working on or near the fan, motor, Fight fixture or junction box, 5.
DIMENSIONS FY-OBVQLS FY-11VQLS RE15VQLS meme Unit: inches {mm} 081 ¢ swe 32-18 3 VA-B 1m {The dimensions in square brackets refer to FV-15VQLS which are different from wg suo PE No. Part name No, Part name 1 Blade 7 Lighting unit 2 Grille 8 Fluorescent lamp 3 Junction box 8 Fan body 4 Adapter 10 Damper 5 Lens 11 Suspension bracket & Night lamp 12 Bracket cover WIRING DIAGRAM (Fuse mortar) FY.
INSTALLATION I (JOIST MOUNTING I} Joist situation: ; A i Spacing Ais 16 inches inches 609 mm) on center joists A) Spigots the spacing A is 16 inches (406 mm) to 24 inches {609 mm) on center joists, please follow the installation step as below. Suspension bracket I i Suspension bracket IT Fig.1 IMPORTANT: Remove the tape from damper and adapter before installation. As shown below: Carper 2. Insert the suspension bracket 1 and I into the fan body.
INSTALLATION I (JOIST MOUNTING -1) CONTINUED 4, install a foulard duct and secure it with damps or wire Reuters duct Hes and seal it with mastic or approved duct tape. Conduit ro x “ {Fig) Junction box 5. Remove junction box corer and secure conduit or Lo stress relief to junction box knock-out hole, {Fig.3) N 6. Refer to wiring diagram below. B Follow all the local electrical safety codes as well as the National Electrical Code (NECK.
INSTALLATION 1 (JOIST MOUNTING -I} CONTINUED IMPORTANT: Install fluorescent lamp and night lamp as below: i if (© Remove screw Light cover (ax) "Fluorescent farm Calling plug connector I Mounting spring Fig 8. Insert the grille mounting spring on the wiring side into the slot. {Fig.6} 9. Insert the plug connector I into the housing of the lighting unit and insert other mounting spring into the slot as shown and mount grille to fan body. {Fig.6, Fig.
INSTALLATION I {SUSPENSION BRACKETS MOUNTING) CONTINUED Suspension bracket connect method: Suspension bracket I and H connect with screw I as shown below: Unit: Inches rin) 13 174 ~ 15 1/2 (335-386) {219-480} 21/4 «23172 54059 se = eu! raciest Lents Screw Teg (5Ta.26) Suspension bracket I 3. install the suspension bracket to joists by using long screws {STA.2X20} {Fig.9) and secure it to the fan body by using screw I (Fig.10} 4, Follow steps installation I {page §, page 7} to complete the installation work.
INSTALLATION IT (JOIST MOUNTING 11} Joist situation: td Spacing Bis 10 1/2 inches (266 inches (292 mm, FA dos inches on joists the spading inches (266 hes (292 mm) on joists, please follow the installation step as below. 2. Secure 4 long screws (5T 4.2620) at flange of frame, {Fig.11) 3. Follow steps installation I {page §, page 7} to complete the installation work. 4 Long screws {578.220} Fig.11 MAINTENANCE I (CLEANING) WARNING: Disconnect power source before working on unit.
MAINTENANCE II (REPLACEMENT OF LAMP) WARNING: or replacement of lamp. 1. Disconnect power source before working on unit. 2. This is a pin type lamp base and the lamps glass is fragile. To remove, pull out carefully. 3. 4W night lamp has threaded base. Remove by muting counterclockwise. 4. Make sure the temperature of lens and lighting unit has cooled down before maintenance {dealing) 1. Remove grille by pulling down one mounting spring. Remove plug connector I then pull down the other mounting spring.
PRACTICAL GUIDE TO INSTALLATION Properly insulate the area around the fan Loose fill or bat insulation can be placed fared taps directly over the fan housing in the attic. i Panasonic fans and fanlight combination ba) units do not create excessive heat that is a comment problem with recessed light 2-3 ft straight run before elbow ii fo f Four inch or six inch roof jack, wall tap Gores to minimize building heat loss and gain. or sit vert with bickerer damper —. RTI {Fig.
Panasonic Corporation of North America One Panasonic Way, Se caucus, New Jersey 07054 www. companionship Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario LAW 273 WOW.
