Ventilating Fan FV-05VFL2 FV-08VFL2 FV-11VFL2 READ AND SAVE THESE INSTRUCTIONS. R Please read these instructions carefully before attempting to install, operate or service the Panasonic Ventilating Fan. Failure to comply with instructions could result in personal injury and/or property damage. Please retain this booklet for future reference.
FV-05VFL2 FV-08VFL2 FV-11VFL2 Part name Grille Suspension bracket I Suspension bracket II Appearance Appearance Quantity Part name Quantity 1 Machine screw M4X8 1 8 1 Long screw M4X30 Thumb screw 1 18W Fluorescent lamp 2 4W Incandescent lamp 1 Light unit 1 3 inch adaptor connector (optional part) 1 1 Suspension bracket III 1 Screw I M4X8 2 Screw II M4X12 2 Screw III M4X16 2 These Panasonic ceiling mount ventilating fan models use a sirocco fan with dolphin-shaped blades dr
FV-05VFL2 FV-08VFL2 FV-11VFL2 Unit: inches(mm) 2 7/8 (73) 9 7 1 (26) 3 1/2 (90) 1 (25) 1 3/4 (45) 13 1/4~15 1/2 ( 336~394 ) 16 1/2~18 3/4 ( 419~480 ) 21 1/4~23 1/2 ( 540~597 ) 3 1/4 (81) 11 7 / 8 ( 3 0 1 ) 10 1/4 (259) 3 7/8 (98) 2 15/16 (74) 8 4 3/8 (110) 11 10 5 1/2 (141) 13 (330) 12 6 10 1/4 (261) 16 1/8 (410) No. Part name No.
FV-05VFL2 FV-08VFL2 FV-11VFL2 Duct diameter (inches) Noise (sone) 4 3 4 3 4 3 <0.3 <0.3 0.5 0.6 1.3 1.5 (cfm) 16 15 30 30 33 33 36 4 36 4 36 4 700 760 830 940 910 1050 50 50 80 70 110 90 11.0 (5.0) 11.0 (5.0) 11.0 (5.0) Specifications are based on HVI standard. Unpack and carefully remove unit from carton. Refer to the Supplied Accessories list to verify that all parts are present. o o 1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F). 2.
CAUTION: 1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2. Not for use in cooking area. (Fig .B) 3. This product must be properly grounded. (Cooking area) Do not install above or inside this area o 45 o 45 Cooking equipment Floor Fig. B WARNING: To reduce the risk of fire, electric shock or injury to persons, observe the following; A. Use this unit only in the manner intended by the manufacturer.
1. Before installation, secure the fan body to adaptor by using thumb screw.(Fig.1) Thumb screw Connection method for 3 inches adaptor connector Fan body Duct tape 2 1 3 Fig.1 3 inches adaptor connector IMPORTANT: Remove the tape from damper and adaptor before installation. As show below: Adaptor Damper Suspension bracket I Remove the tape Fan body Fig.2-1 2. Insert the supension bracket into the fan body and adaptor.
3. Install the suspension bracket and the flange of fan body to joists by using long screws (M4X30) ( If spacing A between joists is 10 1/4~12 inches, install the flange of fan body according to Fig.3-2, others according to Fig.3-1 install the product) Joist Fan body Fig.3-1 4-Long screws(M4X30) Fan body Joist 2-Long screws (M4X30) Fig.3-2 4. Install the suspension bracket to joists by using long screws (M4X30) and secure it to the fan body by using screw II (M4X12) (Fig.4) 5.
. Finish ceiling work. Ceiling hole should be aligned with the edge of the flange. (Fig.6) 5) 10 7/8 10 (27 7/8 (27 5) Ceiling 9. Insert the plug connector II and plug connector III into the receptacle II and receptacle III respectively, and secure the light unit to the fan unit with 2 screw III (M4X16) and 1 machine screw (M4X8). (Fig.6) Plug connector II Plug connector III 10. Insert the fluorescent lamps and screw the night lamp into the light unit.(Fig.
4. Insert the suspension bracket into fan body (refering to step 2 of installation I, page 6) Circular duct Joist 5. Insert the fan body into joists. (Fig.9) Conduit IMPORTANT: Junction box cover Make sure that adaptor claws are properly inserted into body slots. 6. Secure the fan body to adaptor by using thumb screw and plug connector to receptacle(Fig.10) 7.
C 4 kinds of I-joist inches (mm) 9/16 (14.3) C1 11/16 (17.5) C2 31/32 (24.6) C3 C4 1 17/32 (38.9) Fan body Thumb screw C3 C4 Fig.13 Suspension bracket III C1 Screw II (M4X12) C2 Suspension bracket III The suspension bracket III can comply with different kinds of I-joists. Fig.14 1. Before installation, secure the fan body to adaptor by using thumb screw (Fig.13). Secure the lighting unit to fan body (refering to Fig.6 of page 8). 2. Connect the suspension bracket III to fan body. (Fig.
3. Insert the fan body between joists. Make sure the fan body is level and square (perpendicular) with the joists.(Fig.17) Keep the distance B (7/8 inch, 21.6mm) for the thickness of ceiling board. Joists Adaptor Ventilating fan Junction box A 13 1/4~15 3/4 ( 336~400 ) 16 1/2~18 3/4 ( 419~480 ) 3~5 (76~126) 5 4/5~7 4/5(148~198) inches ( mm ) 4. Secure the suspension bracket to joists by using long screws(M4X30) (Fig.18, Fig.19) Fig.17 2-Long screws(M4X30) Fig.18 5.
4. Follow steps 5 to 11 of installation I (page 7,page 8) to complete the installation work. Adaptor Circular duct 6-Long screws (M4X30) Conduit Junction box Wire nut Lead wires Green wires Fig.21 1. Installation in existing construction. Installing the ventilating fan in an existing building requires an accessible area (attic or crawl space) above the planned installation location or existing ducting and wiring. (1) To install the ventilating fan, follow the procedures described in lnstallation II .
Slot WARNING: Disconnect power source before working on unit. Routine maintenance must be done every year. Mounting spring CAUTION: 1. Never use petrol, benzene, thinner or any other such chemicals for cleaning the ventilating fan. 2. Do not allow water to enter motor. o 3. Do not immerse resin parts in water over 60 C. Glove Grille Fig. 22 1. Remove grille. (Squeeze mounting spring and pull down carefully.) (Fig.22) 2. Wash and clean grille.
1. Remove grille. (Squeeze mounting spring and pull down) (Fig.22 of page 13) Plug connector III Plug connector II 2. Disconnect the connector II or connector III of light unit. (Fig.26) Receptacle II Receptacle III 3. Change the fluorescent bulbs (Panasonic FDS 18E27/4,18W or FDS18E35/4, 18W or FDS18E42/4, 18W ) or the 4W incandescent lamp, connect the connector II or connector III and replace the grille.(Fig.27) Fluorescent lamp 4 W Night Lamp Fig.26 Fig.
