No. Classification Chip RF Jumper 151-XB-JP00BE PRODUCT SPECIFICATION FOR INFORMATION Subject EXBD6JP000A 12 - 10 1. Dimensions, structure and materials L A1 6 - φD 6 T B1 5 W 4 B1 E1 1 2 3 P E2 T2 F1 A2 A Ｂ Ｂ’ F2 B2 B2 F1 A’ F2 L W T1 A1 B1 E1 F1 Dimensions 3.20±0.15 1.60±0.15 0.55±0.15 0.40±0.15 0.20±0.15 0.40±0.15 0.20±0.15 (mm) A2 P D 1.905 Dimensions 0.40±0.15 0.38±0.15 0.40±0.15 0.35±0.15 0.20±0.15 (mm) ±0.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A 12 - 11 2. Specifications Item Resistance(between 1-4 terminal) Isolation (2.5 GHz) Return loss (2.5 GHz) Insertion loss (2.5 GHz) Rated current 1) Maximum rated current Number of Terminals Category temperature range Specification 50 mΩ max. -40 dB max. -20 dB max. -0.5 dB min.
No. Classification Chip RF Jumper 151-XB-JP00BE PRODUCT SPECIFICATION FOR INFORMATION Subject EXBD6JP000A 12 - 12 6. Performance specification 6.1. Standard environmental condition Unless otherwise specified, ambient atmosphere at performance tests and measuring shall meet the following conditions. Ambient temperature: 25 °C ± 2 °C, Relative humidity: 45 % to 75 %, Atmosphere pressure: 86 kPa to 106 kPa 6.2.
No. Classification Chip RF Jumper 151-XB-JP00BE PRODUCT SPECIFICATION FOR INFORMATION Subject EXBD6JP000A Characteristics 6.3.3. Return loss Specification -20 dB max. (2.5 GHz) 12 - 13 Test method Specimens shall be measured at the test circuit specified below. Measuring board: the attached drawing Measuring equipment: network analyzer Measuring parameter: s parameter (S11) Measuring power: 0 dBm Port 1 6 5 2 3 4 1 50 Ω 50 Ω 6.3.4. Insertion loss -0.5 dB min. (2.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A 12 - 14 6.4. Environmental performance Characteristics 6.4.1. Rapid change of temperature Specification 50 mΩ max. Test method Specimens shall be tested for 700 cycles continuously in accordance with the following duty cycle. * Prior to use, verify the performance, reliability, etc. thoroughly, if you use the board that is not glass-fabric based epoxy resin.
No. Classification Chip RF Jumper 151-XB-JP00BE PRODUCT SPECIFICATION FOR INFORMATION Subject EXBD6JP000A 12 - 15 7. Mechanical Performance Characteristics Specification 7.1.1. 50 mΩ max. Bond strength of the and no evidence of face plating mechanical damage. 7.1.2. Solderability Test method Specimens shall be placed on testing board that is glass-fabric based epoxy resin with 100 mm in length, 40 mm in width and 1.6 mm in thickness.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A MATSUSHITA ELECTRONIC COMPONENTS CO., LTD.
No. Classification Chip RF Jumper 151-XB-JP00BE PRODUCT SPECIFICATION FOR INFORMATION Subject EXBD6JP000A 12 - 17 8.3. Flux Use rosin-based flux. Do not use high-activity flux (the chlorine content is 0.2wt% or more.) 8.4. Precaution for handling of substrate Do not bend the board after soldering the product extremely.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A • Reflow soldering shall be within five times. MATSUSHITA ELECTRONIC COMPONENTS CO., LTD.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A 12 - 19 8.7. Caution of flow soldering We can not recommend the flow soldering to the product, because we are afraid that solder bridge may happen owing to narrow pitch of it’s terminals. 8.8. Replacement with soldering iron Note the followings in case of using soldering iron for replacement. (1) The tip temperature should be less than 350 °C for the period within 3 s for each terminal.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A 12 - 20 ! Notice for use Accordingly, the use in the following special environments, and such environmental conditions may affect the performance of the product; prior to use, verify the performance, reliability, etc. thoroughly. 1) Use in liquids such as water, oil, chemical and organic solvent.
No. Classification Chip RF Jumper 151-XB-JP00BE PRODUCT SPECIFICATION FOR INFORMATION Subject EXBD6JP000A 12 - 21 12. Period of validity for specification If there is not an offer by 3 months before term of validity, term of validity shall be extended every one year. When you confirm revision of this specification while it is in effect, the previous, unrevised version shall lose its validity. 13. Production place Production country: Japan Production factory: Fukui Matsushita Electric Co., Ltd. 14.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A 12 - 22 14.3. Taping reel dimensions and material Unit: mm 11.4±2.0 180 -30 60 min. 13.0±1.0 9.0±1.0 * Material: PS 14.4. Taping specification There shall be portions having no product in both the trailer and the leader of taping, and there shall be portion having only cover tape in the leader of taping as shown below.
No. Classification Chip RF Jumper PRODUCT SPECIFICATION FOR INFORMATION 151-XB-JP00BE Subject EXBD6JP000A 12 - 23 14.6.
