Operating Instructions

Maintenance
• Make sure that the main body is turned off.
• After cleaning, be sure to store with the
blades, the trimmings box and the
protective cap attached.
How to clean
►With water
1.Apply some hand soap and some
water to the outer blade.
2. Turn on the power and turn off the
powerafter10seconds.(Fig.7‑1)
▼ ▼
To remove light dirt To remove heavy dirt
3.Open the water
inlet and turn on
the power again.
▪ If the trimmings
box is removed,
open the water
inlet after
attaching the
trimmings box.
4. Run water down
the water inlet
(Fig.7‑ 2 ), rinse
well and turn off.
3.Remove the
head,the blades
and the
trimmings box.
4. Rinse them with
running water.
• Coverthe
drainage outlet
of washbasin to
prevent the inner
blade from
owingaway.
(Fig.7‑ 3 )
▼ ▼
5. Wipe off the water with a dry cloth and
dry it well.
▪It will dry faster with the blades and
the trimmings box removed.
Notes
• Note the following precautions to avoid
malfunction and damage.
• Do not use hot water or any
detergents other than hand soap.
• Do not wipe with thinner, benzine,
alcohol etc.
►With the cleaning brush (Fig. 8)
1.Remove the head, blades and the
trimming box.
2. Brush off any hair trimmings from the
head, blades and the trimming box.
▪
Be careful not to deform the inner blade.
▪Becarefulnottodamagethelter.
How to open and
close the water inlet
►Open
Rotatethewashswitchringuntilits“ ”
markalignswiththe“ ” mark of the
head to open the water inlet. (Fig. 9-1)
►Close
Rotatethewashswitchringuntilits“ ” mark
alignswiththe“ ” mark of head. (Fig. 9- 2 )
Removing and mounting
the trimmings box
►Remove (Fig. 10‑1)
Rotatethewashswitchringuntilits“ ” mark
alignswiththe“ ” mark of the head.
►Mount (Fig. 10‑2)
1.Alignthe“ ” mark of the trimmings
boxwiththe“ ” mark of the head.
▪Becarefulnottodamagethelter
with the shaft (c).
2. Rotate the wash switch ring until its
“ ”markalignswiththe“ ” mark of
the head.
Removing and mounting
the blade (Fig. 11)
►Outer blade
Remove
Rotate the outer blade in the direction of
the arrow and remove the blade. (1)
Mount
Insert the head’s shaft (d) into the hole
of the inner blade.
Rotatetheouterbladetoalignits“ ”mark
withthe“ ” mark of the head. ( 2 )
►Inner blade
Remove
Pull to remove the inner blade.
Mount
Insert the inner blade straight into the
outer blade.
Troubleshooting
Problem Action
The cutting
performance
has reduced.
Replace the blade.
Cleantheinnerblade.
There is an
odd odour.
Blade does not
move/rotate
smoothly.
The suction
power is low.
Cleanthetrimmingsbox.
Closethewaterinlet.
If the problems still cannot be solved,
contact your dealer or a service centre
authorized by Panasonic for repair.
Specications
Airborne Acoustical Noise
62(dB(A)re
1pW)
This product is intended for household
use only.
Printed in Thailand
ER9210CNT13111
E0422-0
Panasonic Corporation
https://www.panasonic.com
© Panasonic Corporation 2022
F EN
ER-CNT1_UK_PR.indd 2 2022/02/28 19:17:03