Datasheet
Aluminum Electrolytic Capacitors/TA
EE48
Design, and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase
and / or use. Should a safety concern arise regarding this product,please be sure to contact us immediately. Apr. 2005
TA
V
Series:
Type :
-40 to +125°C
10 to 50 V .DC
10 to 330 µ F
±20 % (120Hz/+20°C)
I 0.01 CV or 3(µ A) after 2 minutes (Whichever is greater)
W.V. (V) 10 16 25 35 50
-25 / +20 °C 8 5 4 3 3
-40 / +20 °C 14 12 10 8 8
D L A,B H I W P K
Size
code
E
F
G
8.0 6.2 8.3 9.5MAX 3.4 0.65±0.1 2.2 0.35
8.0 10.2 8.3 10.0MAX 3.4 0.90±0.2 3.1 0.70
10.0 10.2 10.3 12.0MAX 3.5 0.90±0.2 4.6 0.70
±0.2
±0.2
-0.20 to +0.15
V 10 16 25 35 50
Code A C E V H
10 (1A) 16 (1C) 25 (1E) 35 (1V) 50 (1H)
Cap. (µF)
10
22
33
47
100
220
330
F
G
E
F
G
W.V.(V)
E
F
E
F
G
E
E
F
G
(µF)
C TA
100
Surface Mount Type
n Features
Endurance:125°C 1000 h
For use near car engines.
Good for electronically controlled units (ECU, ABS etc).
Vibration-proof product is available upon request.(φ8 )
RoHS directive not compliant.
TG series is recommended for RoHS compliant.
n Specifications
Category temp. range
Rated W.V. Range
Nominal Cap. Range
Capacitance Tolerance
DC Leakage Current
tan δ
Characteristics
at Low Temperature
Endurance
Shelf Life
Resistance to
Soldering Heat
n Marking
Example: 16V 100 µF (Polarized)
W.V. code
Negative polarity
marking
Series
identification
Capacitance
Lot number
W.V. code
n Case size
( ) reference size
n Dimensions in mm (not to scale)
After applying rated working voltage for 1000 hours at +125±2°C and then being stabilized
at +20°C, capacitors shall meet the following limits.
After storage for 500 hours at +125 ±2°C with no voltage applied and then being stabilized
at +20°C, capacitors shall meet the following limits. (With voltage treatment)
Capacitance change
tan δ
DC leakage current
Capacitance change
tan δ
DC leakage current
Capacitance change
tan δ
DC leakage current
After reflow soldering and then being stabilized at +20°C, capacitor shall meet the following
limits.
±10 % of initial measured value
initial specified value
initial specified value
±30 % of initial measured value
300 % of initial specified value
initial specified value
Please see the attached standard products list
±20% of initial measured value
200 % of initial specified value
initial specified value
(Impedance ratio at 120Hz)
K
0.3 max
φD±0.5
w
(I)
(P)
(I)
H
L ±0.3
A ± 0.2
Japan
<
=
<
=
<
=
<
=
<
=
<
=
<
=
B± 0.2
(mm)
<
Country of Origin
=
Discontinued