Datasheet

ManualsBrandsPANASONIC ManualsCapacitorsElectrolytic capacitor Snap-in 270 µF 420 V 20 % (Ø) 22 mm 1 pc(s)

To: DIGI-KEY CORPORATION

Issue No : TS-UQ-EM-73

Date of Issue : May 28, 2012

E N G I N E E R I N G D R A F T

Product Description : Aluminum Electrolytic Capacitor

Product Part Number : EETUQ2G271KF, EETUQ2S271BF

Country of Origin : Malaysia

Marking of the Origin : Printed on the packaging label

Applications : Power Supply

Term of Validity : May 27, 2013 from the date of issue

※These specifications are temporary specifications. Ask factory for technical specifications before purchase

and / or use.

Capacitor Business Unit

Industrial Devices Company,

Panasonic Corporation

25 Kohata-nishinaka, Uji City,

Kyoto, 611-8585, Japan

Phone: +81-774-32-1111

Phone: +81-774-33-3209 (Direct)

Prepared by : Engineering Team 4

Engineering Group

Aluminum Capacitor Division

Contact Person :

Signature : ______________________

Name (Print) : Susumu Morishita

Title Engineer

Authorized by

Signature : ______________________

Name (Print) : Hisao Nagara

Title : Manager

No.4626131

Summary of content (8 pages)

PAGE 1
To: DIGI-KEY CORPORATION Issue No Date of Issue E N G I N E E R I N G : TS-UQ-EM-73 : May 28, 2012 D R A F T Product Description : Aluminum Electrolytic Capacitor Product Part Number : EETUQ2G271KF, EETUQ2S271BF Country of Origin Marking of the Origin Applications Term of Validity : : : : Malaysia Printed on the packaging label Power Supply May 27, 2013 from the date of issue ※These specifications are temporary specifications. Ask factory for technical specifications before purchase and / or use.
PAGE 2
TS-UQ-EM-73 Engineering Draft Notice matter  Law and regulation which are applied  This product complies with the RoHS Directive (Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (DIRECTIVE 2002/95/EC).  No Ozone Depleting Chemicals (ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product.  We do not PBBs or PBDEs as brominated flame retardants.
PAGE 3
Product Specification TS-UQ-EM-73 EETUQ2G271KF 1 [Specification] Customer Part No. Product Part No. EETUQ2G271KF General Specification Item Nominal Cap. Cap. Tolerance Rated Working Volt. Surge Voltage Unless specification otherwise, the product shall conform to JIS-C-5101-4-1 Specification 270 µF -20 ~ +20 % 400 V.DC 450 V.DC Leakage Current 0.98 mA max D.F. (tan δ) 0.15 max Category temp.
PAGE 4
Product Specification TS-UQ-EM-73 EETUQ2S271BF 2 [Specification] Customer Part No. Product Part No. General Specification Item Nominal Cap. Cap. Tolerance Rated Working Volt. Surge Voltage EETUQ2S271BF Unless specification otherwise, the product shall conform to JIS-C-5101-4-1 Specification 270 µF -20 ~ +20 % 420 V.DC 470 V.DC Category temp.
PAGE 5
Engineering Draft Guideline-ALTS-S1-2 Application Guidelines Guidelines - 1 • This specification guarantees the quality and performance of the product as individual components. Before use, check and evaluate their compatibility with installed in your products. • Do not use the products beyond the specifications described in this document.
PAGE 6
Engineering Draft Guideline-ALTS-S1-2 Application Guidelines Guidelines - 2 1.3. Common Application Conditions to Avoid The following misapplication load conditions will cause rapid deterioration of a capacitor's electrical parameters. In addition, rapid heating and gas generation within the capacitor can occur, causing the pressure relief vent to operate and resultant leakage of electrolyte. Under extreme conditions, explosion and fire ignition could result.
PAGE 7
Engineering Draft Guideline-ALTS-S1-2 Application Guidelines Guidelines - 3 1.7. Capacitor Sleeve The vinyl sleeve or laminate coating is intended for marking and identification purposes and is not meant to electrically insulate the capacitor. The sleeve may split or crack if immersed into solvents such as toluene or xylene and then subsequently exposed to high temperatures. 2.0 Capacitor Handling Techniques 2.1. Considerations Before Using (1) Capacitors have a finite life.
PAGE 8
Engineering Draft Guideline-ALTS-S1-2 Application Guidelines Guidelines - 4 2.8. Mounting Adhesives and Coating Agents When using mounting adhesives or coating agents to control humidity, avoid using materials containing halogenated solvents. Also, avoid the use of chloroprene based polymers. Harden on dry adhesive or coating agents well lest the solvent should be left.