Datasheet

Product Specification
E-XS-ML-5001-1
Specialty Polymer Aluminum Electrolytic Capacitors
(CX/SX)
14
(2) Heat stress of re-flow, etc.
Specified re-flow conditions must be strictly observed.
Soldering under other conditions can cause short circuits and increases in ESR.
(3) Repair and modification by soldering iron.
When using a soldering iron, set the tip temperature to no more than 350°C, and work in as short a time
as possible under 10s. While soldering, do not apply strong force to the capacitor.
(4) Mechanical stress
Do not apply excessive force to the capacitor, since this can damage the electrodes and badly affect
the capacitor’s mountability. It can also cause the increase of leakage current, separation of the lead wire
and element, and damage to the capacitor body, all of which can badly affect the electrical performance
of the capacitor.
9.2.4 Transportation
Take sufficient care during handling because excessive vibration, or shock can cause the reliability of the
capacitor to decrease.
9.2.5 Circuit Board Cleaning
Products should be cleaned after soldering in accordance with the following conditions.
Temperature: Less than 60°C
Time: Within 5min(Ultrasound OK)
Be sure to sufficiently wash and dry (20min at 100°C) the board afterward.
[Recommended cleaning solvents]
Pine Alpha ST-100S, Clean-thru 750H, Clean-thru 750L, Clean-thru710M, Aqua Cleaner 210SEP
Sunelec B-12, DK beclear CW-5790, Techno Cleaner 219, Cold Cleaner P3-375, Telpen Cleaner EC-7R
Techno Care FRW-17, Techno Care FRW-1, Techno care FRV-1, AXREL32
Note1: Consult our factory when performing processes with cleaning solvents other than those listed above.
2: The use of ozone depleting cleaning agents are not recommended in the interest of protecting the
environment.
9.3 Others
9.3.1 Precautions for using capacitors
Before using the products, carefully check the effects on their quality and performance, and determined
whether or not they can be used. These products are designed and manufactured for general-purpose and
standard use in general electronic equipment. These products are not intended for use in the following special
conditions.
(1) In liquid, such as Water, Oil, Chemicals, or Organic solvent
(2) In direct sunlight, outdoors, or in dust
(3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a
high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
(4) In an environment where strong static electricity or electromagnetic waves exist
(5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these
products
(6) Sealing or coating of these products or a printed circuit board on which these products are mounted, with
resin and other material
(7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering.
(In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues)
(8) Acid or alkaline environments.
(9) Environment subject to excessive vibration and shock.
9.3.2 Emergency Procedures
If the capacitor is overheated, the resin case may emit smoke. If this occurs, immediately switch off the unit's
main power supply to stop operation. Keep your face and hands away from the capacitor, since the
temperature may be high enough to cause the capacitor to ignite and burn.
9.3.3 Capacitor Disposal
Since capacitors are composed of various metals and resins, treat them as industrial waste when arranging
for their disposal.
Panasonic Electronic Devices Co.,Ltd
Design, Specifications are subject to change without notice. Contact your nearest Panasonic sales office for the latest specifications prior to purchase and/or use. Whenever any doubt
about safety comes up with this product, please contact us immediately for engineering assistance without fail. Specifications are typical and may not apply to all applications.