Datasheet

Design and specifi cations are each subject to change without notice. Ask factory for the current technical specifi cations before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Electric Double Layer Capacitors (Gold Capacitor)/ SE
– EEC-6 –
P
0
φD
0
P
1
F
P
2
P
5.4±0.8
φd
H
1
13.4 max.
H
0
W
W
1
W
2
W
0
oh
–
+
–
+
oh
1
10.5 max.
■ Features
●
Endurance : 70 °C 1000 h
●
Automatic insertion available
●
RoHS directive compliant
Stacked Coin Type
Series:
SE
■ Specifi cations
Category Temp. Range –25 °C to +70 °C
Maximum Operating Voltage 5.5 V.DC
Nominal Cap.Range 0.022 F to 0.22 F
Characteristics at Low
Temperature
Capacitance change ±30 % of initial measured value at +20 °C (at –25 °C)
Internal resistance
<
5 times of initial measured value at +20 °C (at –25 °C)
Endurance
After 1000 hours application of 5.5 V. DC at +70 °C, the capacitor shall meet the following limits.
Capacitance change ±30 % of initial measured value
Internal resistance
<
4 times of initial specifi ed value
Shelf Life
After 1000 hours storage at +70°C without load, the capacitor shall meet the specifi ed
limits for Endurance.
■ Di men sions in mm(not to scale)
■ Recommended Applications
●
Memory back-up for video and audio equipment,
cameras, tele phones, printers, data terminals,
rice cookers and intelligent remote controls.
■ Standard Products
Maximum
Op er at ing Volt age
Capacitance
Capacitance
tolerance
Internal resistance
(Initial specifi ed value)
Part number
Min. Packaging
Q’ty
(V.DC) (F) (F) (
액
) at 1kHz (pcs)
5.5
0.022 0.0176 to 0.0396
<
150
EECSE0H223
1000
0.047 0.0376 to 0.0846
<
120
EECSE0H473
1000
0.10 0.080 to 0.180
<
75
EECSE0H104
1000
0.22 0.176 to 0.396
<
75
EECSE0H224
1000
+0.8
–0.2
Dimensions Nominal Tolerance
φ
d 0.55 ±0.05
P0 12.7 ±0.2
F 5.0
W 18.0 ±0.5
W
0
5.5
<
–
W
1
9.0 ±0.5
W
2
0 to 3.0 –
H
0
16.4 ±0.5
φ
D
0
4.0 ±0.2
P 12.7 ±1.0
P
1
3.85 ±0.50
P
2
6.35 ±1.00
욼
h,
욼
h
1
0 ±1.0
H
1
30.3
>
–
Note: 1. When ordering please observe the minimum packaging quantity.
2. When the surface mount component goes through UV or a heat oven to affi x the adhesive glue, the capacitor’s surface
temperature should not exceed 100 °C for more than 60 seconds (maximum tem per a ture should not exceed 105 °C)
3. Do not use refl ow soldering. (IR, Atmosphere heating methods, etc.)
Please refer to the page of “Application Guidelines”.
(Unit : mm)
01 Feb. 2013