Datasheet

ManualsBrandsPANASONIC ManualsCapacitorsElectrolytic capacitor SMD 15 µF 8 V 20 % 1 pc(s)

Ð EE225 Ð

Capacitance change

+40%, Ð20% of initial measured value (4W.V.:+60%, Ð20% 6.3W.V.:+50%, Ð20%)

D.F.

<Initial specified value

(4W.V.,ECGCBRA:<200 % of Initial specified value)

DC leakage current <Initial specified value

Ð40 to +105ûC

4 to 16V.DC

2.2 to 82µF

±20% (120Hz/+20ûC)

I<0.04CV or 3 (µA) after 2 minutes (Whichever is the greater)

(4W.V.:0.06CV)

<0.06 (120Hz/+20ûC)

Series:

Chip Type Specialty Polymer

Aluminum Electrolytic Capacitors

(SP Cap)

Japan

Specialty Polymer

Aluminum Electrolytic Capacitors/CB

Rated W.V. Range

Operating Temp. Range

Capacitance Tolerance

Nominal Cap. Range

DC Leakage Current

Rated Working Voltage ×1.25 (15 to 35ûC)

Surge Voltage

After applying rated working voltage for 1000 hours at +105ûC, and then being

stabilized at +20ûC, capacitor shall meet the following limits.

Capacitance change ±10% of initial measured value

D.F. <Initial specified value

DC leakage current <Initial specified value

Endurance

After storing for 500 hours at +60ûC, 90% R.H.

Moisture Resistance

2A DC max. (This shall be applicable only when each terminal is landed or the circuit

individually).

Permissible Current

Between Terminals with

Same Polarity

■Features

●Low impedance at high frequency (10kHz to

10MHz) as low as ceramic capacitors

(Reduced ESR due to an applying speciality polymer

with high conductivity.)

●Excellent Noise-absorbent Characteristics

●Surface Mount (Reflow soldering method available)

●Very stable capacitance, impedance and ESR

against temperature

●Excellent endurance characteristics due to adoption

of solid electrolyte

●4-terminal-construction helps further low impedance.

■Specifications

Dissipation Factor

Summary of content (4 pages)

PAGE 1
Specialty Polymer Aluminum Electrolytic Capacitors/CB Chip Type Specialty Polymer Aluminum Electrolytic Capacitors (SP Cap) Japan CB Series: ■ Features ● Low impedance at high frequency (10 kHz to 10 MHz) as low as ceramic capacitors (Reduced ESR due to an applying speciality polymer with high conductivity.
PAGE 2
Specialty Polymer Aluminum Electrolytic Capacitors/CB ■ Explanation of Part Numbers 1 2 3 4 E C G C Product Code 5 6 7 8 9 10 11 B Style R.W. Voltage Code R Series Code N.Capacitance Code Option ( ■ Marking 12 R: Taped on reel ) ■ Dimensions in mm (not to scale) L + Ð A1 A2 B2 B1 W C1 D D T C2 Polarity bar (Positive) Cap. C1 W.V. code (V) 4 6.3 8 12.5 16 (W.V. code) g j k B C Size code L ±0.2 W±0.1 7.9 Size code T±0.1 A1±0.1 A2±0.1 5.3 3.3 1.2 2.
PAGE 3
Specialty Polymer Aluminum Electrolytic Capacitors/CB ■ Mounting Specifications. 4-terminal 2-terminal 120 s or more on Time in 200 50 230 Ð + 1.9 1.6 220 Ð + 1.9 1.6 5.9 + Ð 240 5.9 surface 100 160 ¡C 1.7 min. Peak temperature(¡C) 250 200 1.7 min. 5 s 150 Temperature ● Typical land pattern (mm) Peak temperature 250 the of capacitor(¡C) ● Recommendable reflow soldering temperature 210 0 10 20 30 40 Time in 200 ¡C or more Time (s) 50 60 (s) 7.
PAGE 4
MEMO Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail.