Datasheet

ManualsBrandsPANASONIC ManualsCapacitorsElectrolytic capacitor SMD 0.15 µF 50 V 20 % (Ø) 4 mm 1 pc(s)

Ñ EE3 Ñ

Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.

Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.

Aluminum Electrolytic Capacitor/V-G

Series: G

Type :

-40 to + 105°C

6.3 to 50 V .DC

0.1 to 470 µ F

±20 % (120Hz/+20°C)

I < 0.01 CV or 3 (µ A) after 2 minutes (Whichever is the greater)

50 G

W.V.

tan δ

6.3 10 16 25 35 50

0.30 0.22 0.16 0.14 0.12 0.12

( Impedance ratio at 120 Hz)

W.V. (V) 6.3 10 16 25 35 50

-25 / +20 °C 4 3 2 2 2 2

-40 / +20 °C 8 6 4 4 3 3

E C E V G

Discontinued

Surface Mount Type

■ Features

Endurance :105°C 1000 h

■Specification

Operating temp. range

Rated W.V. range

Nominal cap. range

Capacitance tol.

DC leakage current

tan δ

(120Hz / +20°C)

Characteristics

at Low Temperature

Endurance

Shelf life

Resistance to

Soldering Heat

■Explanation of Part Number

Common code Shape W.V. code Series code Capacitance code Suffix

■ Marking

Example : 50V22µF

Rated voltage (V.DC)

(-): Negative polarity

marking

Capacitance (µF)

Series identification

■ Dimensions in mm (not to scale)

After applying rated working voltage for 1000 hours at +105 ±2°C, and then being atabilized at

+20°C, capacitors shall meet following limits.

After storage for 1000 hours at +105 ±2°C with no voltage applied and then being stabilized

at +20°C, capacitor shall meet the limits specified in “Endurance”.

Capacitance change

tan δ

DC leakage current

< ±10% of initial measured value

< initial specified value

Capacitance change

tan δ

DC leakage current

< ±20% of initial measured value

< 200% of initial specified value

< initial specified value

After reflow soldering (230°C of peak temperature and reflow time less than 20 seconds.) and

then being stabilized at 20°C, capacitor shall meet the following limits, (Infrared ray oven is also

available.)

W=12 mm

W=16 mm

W=24 mm

φ4(B)

φ5,φ6.3,φ8x6.2(C,D,E)

φ8x10.2, φ10x10.2(F,G)

Taping

(mm)

( ) reference size

0.3 max

φD±0.5

(I)

(P)

(I)

+0.1

@A±0.2

E,F,G= L±0.3

-0.2

D L A H I W P K

Size

code

-0.20 to +0.15

±0.2

-0.20 to +0.15

4.0 5.4 4.3 5.5MAX 1.8 0.65± 0.1 1.0 0.35

5.0 5.4 5.3 6.5MAX 2.2 0.65 ±0 .1 1.5 0.35

6.3 5.4 6.6 7.8MAX 2.6 0.65±0.1 1.8 0.35

8.0 6.2 8.3 9.5MAX 3.4 0.65±0.1 2.2 0.35

8.0 10.2 8.3 10.0 MAX 3.4 0.90±0.2 3.1 0.70

10.0 10.2 10.3 12.0MAX 3.5 0.90±0.2 4.6 0.70

-0.20 to +0.15

Mar. 2005

Summary of content (9 pages)

PAGE 1
Aluminum Electrolytic Capacitor/V-G Surface Mount Type Type : V Series: G ■ Features Discontinued Endurance :105°C 1000 h ■Specification Operating temp. range -40 to + 105°C Rated W.V. range Nominal cap. range 6.3 to 50 V .DC 0.1 to 470 µ F Capacitance tol. DC leakage current ±20 % (120Hz/+20°C) I < 0.01 CV or 3 (µ A) after 2 minutes (Whichever is the greater) tan δ W.V. tan δ (120Hz / +20°C) Characteristics at Low Temperature 6.3 10 16 25 35 50 0.30 0.22 0.16 0.14 0.12 0.12 W.V.
PAGE 2
Aluminum Electrolytic Capacitor/V-G Discontinued ■ Case size / Ripple current (mA) r.m.s. (120Hz/+105°C) ● Polarized W.V.(V) Cap. (µF) 0.1 0.22 0.33 0.47 1.0 2.2 3.3 4.7 10 22 33 47 100 220 330 470 6.
PAGE 3
Aluminum Electrolytic Capacitor Application Guidelines 1.2 Operating Temperature and Life Expectancy 1. Circuit Design E n s u r e t h a t operational and mounting conditions follw the specified conditions detailed in the catalog and specification sheets. 1.1 Operating Temperature and Frequency E l e c t r o l y t i c c a p a c i t o r e l e c t r i c a l p a ra m e t e r s a r e normally specified at 20°C temperature and 120Hz frequency.
PAGE 4
Aluminum Electrolytic Capacitor ■ Typical failure modes and their factors Faliure mode Faliure mechanism (internal phenomenon) Production factor Application factor Overvoltage applied Increase in internal pressure Vent operates Capacitance reduction Increase in inter• nal temperature • Reduced anode foil capacitance • • • • • Reduced cathode foil capacitance tan d increase • Excessive ripple current • Reverse voltage applied • Severe charging-discharging AC voltage applied • Defect of
PAGE 5
Aluminum Electrolytic Capacitor 1.3 Common Application Conditions to Avoid The following misapplication load conditions will cause rapid deter ioration to capacitor electr ical p a r a m e t e r s. l n a d d i t i o n , ra p i d h e a t i n g a n d g a s generation within the capacitor can occur causing the pressure relief vent to operate and resuItant leakage of electrolyte. Under extreme conditions, explosion and fire could result. Leakinq electrolyte is combustible and electrically conductive.
PAGE 6
Aluminum Electrolytic Capacitor (5)Clearance for Case Mounted Pressure Relief Vents 2. Capacitor Handling Techniques 2.1 Considerations Before Using Capacitors with case mounted pressure relief vents require sufficient clearance to allow for proper vent operation. The minimum clearances are dependent on capacitor diameters as follows. f6.3 to f16 mm : 2 mm minimum, f18 to f35 mm : 3 mm minimum.
PAGE 7
Aluminum Electrolytic Capacitor 2.4 Flow Soldering (1) Don not immerse the c a p a c i t o r body into the solder bath as excessive internal pressure could result. (2) Observe proper soldering conditions (temperature, time, etc.). Do not exceed the specified limits. (3) Do not allow other parts or components to touch the capacitor during soldering. 2.5 2.
PAGE 8
Aluminum Electrolytic Capacitor (3) A thorough drying after cleaning is required to remove residual cleaning solvents which may be trapped b e t w e e n the capacitor and the circuit board. Avoid drying temperatures which exceed the maximum rated temperature of the capacitor. (4) Monitor the contamination levels of the cleaning solvents during use by electrical conductivity, pH, specific gravity, or water content.
PAGE 9
Aluminum Electrolytic Capacitor 6. Capacitor Disposal When disposing of capacitors, use one of the following methods. ● Incinerate after crushing the capacitor or puncturing the can wall (to prevent explosion due to internal pressure rise). Capacitors should be incinerated at high temperatures to prevent the release of toxic gases such as chlorine from the polyvinyl chloride sleeve, etc. ● Dispose of as solid waste. ● Local laws may have specific disposal requirements which must be followed.