Datasheet

ManualsBrandsPANASONIC ManualsCapacitorsElectrolytic capacitor Snap-in 10 mm 330 µF 250 V 20 % (Ø) 25 mm 1 pc(s)

Ñ EE1 Ñ

Aluminum Electrolytic Capacitors/NH

Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.

Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.

Series: NH

Type: TS

20% (at 120Hz , +20°C)

10 to 100V.DC 160 to 250V.DC

-25 to +105 °C

Frequency (Hz)

50 60 120 500 1k 10k ~ 50K

0.93 0.95 1.0 1.05 1.08 1.15

0.75 0.80 1.0 1.20 1.25 1.40

C x V <100000

<0.01CV(µA)(After 5 minutes)

C x V >100000

3 C V (µA) max.(After 5 minutes)

3 CV( µA) max. After 5 minutes

W.V.(V)

tan δ

10 16 25 35 50 63 80 100 160 to 400

0.45 0.35 0.30 0.23 0.18 0.16 0.12 0.11 0.10

10~100V

160~400V

C.F.

(max)

-40 to +105 °C

350, 400V.DC

{ C :Capacitance(µF) V : W.V.(V)}

Snap-in type

■ Features

Life time : 105°C 2000 h

■Specifications

Operating Temp. Range

Rated W.V. Range

Nominal Cap.Range

DC Leakage Current

{ C :Capacitance(µF) V : W.V.(V)}

Tan δ

Frequency Correction

Factor for Ripple Current

Endurance

Self Life

After 2000 hours application of DC voltage with specified ripple current (< rated DC working

voltage) at +105°C, the capacitor shall meet the following limits.

±20% of initial measured value

<150% of initial specified value

<Initial specified value

Capacitance change

tan δ

Dc leakage current

After storage for 1000 hours at +105°C with no voltage applied, the capacitor shall meet the

specified limits for “Endurance”.

(mm)

❉

2-φ2.0±0.1

φD+1.0 max

L+2.0 max

(10.0)

10.0±0.1

1.5±0.2

(4.0)

6.3±1.0

2.0 max

+0.2

0.8-0.1

Terminal

(t= 0.8)

Discontinued

■ Dimentions

Polarity bar

Vinyl Sleeve

PC Board Mounting Hole

Safety

vent

❉

Mar. 2005

Summary of content (12 pages)

PAGE 1
Aluminum Electrolytic Capacitors/ NH Snap-in type Series: NH Discontinued Type: TS ■ Features Life time : 105°C 2000 h ■Specifications Operating Temp. Range Rated W.V. Range 10 to 100V.DC 160 to 250V.DC 350, 400V.DC -25 to +105 °C -40 to +105 °C Nominal Cap.Range 20% (at 120Hz , +20°C) C x V <100000 <0.01CV(µA)(After 5 minutes) C x V >100000 C V (µA) max.(After 5 minutes) 3 DC Leakage Current { C :Capacitance(µF) W.V.(V) tan δ Tan δ V : W.V.
PAGE 2
Aluminum Electrolytic Capacitors/ NH Discontinued W.V. (V.DC) Capacitance (µF) 4700 6800 10000 10 15000 22000 33000 3300 4700 6800 16 10000 15000 22000 2200 3300 4700 25 6800 10000 15000 1500 2200 3300 4700 35 6800 10000 Case size Dia. Length (mm) (mm) 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.
PAGE 3
Aluminum Electrolytic Capacitors/ NH Discontinued W.V. (V.DC) Capacitance (µF) 1000 1500 2200 50 3300 4700 6800 680 1000 1500 2200 63 3300 4700 470 680 1000 1500 80 2200 3300 330 470 680 1000 100 1500 2200 Case size Dia. Length (mm) (mm) 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.
PAGE 4
Aluminum Electrolytic Capacitors/ NH Discontinued W.V. (V.DC) Capacitance (µF) 150 220 330 160 470 680 820 100 150 220 180 330 470 680 100 150 220 200 330 470 680 68 100 150 220 250 330 470 Case size Dia. Length (mm) (mm) 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.
PAGE 5
Aluminum Electrolytic Capacitors/ NH Discontinued W.V. (V.DC) Capacitance (µF) 47 68 100 350 150 220 330 33 47 68 400 100 150 220 Case size Dia. Length (mm) (mm) 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 22.5 22.5 25.5 22.5 25.5 30.5 22.5 25.5 30.5 25.5 30.5 35.5 30.5 35.5 25 31.5 25 40 31.5 25 50 40 31.5 50 40 31.5 50 40 25 31.5 25 40 31.5 25 50 40 31.5 50 40 31.5 50 40 Ripple Current Part No. (A r.m.s. 120Hz) 0.44 0.56 0.56 0.69 0.69 0.69 0.82 0.82 0.82 1.0 1.0 1.
PAGE 6
Aluminum Electrolytic Capacitor Application Guidelines 1.2 Operating Temperature and Life Expectancy 1. Circuit Design E n s u r e t h a t operational and mounting conditions follw the specified conditions detailed in the catalog and specification sheets. 1.1 Operating Temperature and Frequency E l e c t r o l y t i c c a p a c i t o r e l e c t r i c a l p a ra m e t e r s a r e normally specified at 20°C temperature and 120Hz frequency.
PAGE 7
Aluminum Electrolytic Capacitor ■ Typical failure modes and their factors Faliure mode Faliure mechanism (internal phenomenon) Production factor Application factor Overvoltage applied Increase in internal pressure Vent operates Capacitance reduction Increase in inter• nal temperature • Reduced anode foil capacitance • • • • • Reduced cathode foil capacitance tan d increase • Excessive ripple current • Reverse voltage applied • Severe charging-discharging AC voltage applied • Defect of
PAGE 8
Aluminum Electrolytic Capacitor 1.3 Common Application Conditions to Avoid The following misapplication load conditions will cause rapid deter ioration to capacitor electr ical p a r a m e t e r s. l n a d d i t i o n , ra p i d h e a t i n g a n d g a s generation within the capacitor can occur causing the pressure relief vent to operate and resuItant leakage of electrolyte. Under extreme conditions, explosion and fire could result. Leakinq electrolyte is combustible and electrically conductive.
PAGE 9
Aluminum Electrolytic Capacitor (5)Clearance for Case Mounted Pressure Relief Vents 2. Capacitor Handling Techniques 2.1 Considerations Before Using Capacitors with case mounted pressure relief vents require sufficient clearance to allow for proper vent operation. The minimum clearances are dependent on capacitor diameters as follows. f6.3 to f16 mm : 2 mm minimum, f18 to f35 mm : 3 mm minimum.
PAGE 10
Aluminum Electrolytic Capacitor 2.4 Flow Soldering (1) Don not immerse the c a p a c i t o r body into the solder bath as excessive internal pressure could result. (2) Observe proper soldering conditions (temperature, time, etc.). Do not exceed the specified limits. (3) Do not allow other parts or components to touch the capacitor during soldering. 2.5 2.
PAGE 11
Aluminum Electrolytic Capacitor (3) A thorough drying after cleaning is required to remove residual cleaning solvents which may be trapped b e t w e e n the capacitor and the circuit board. Avoid drying temperatures which exceed the maximum rated temperature of the capacitor. (4) Monitor the contamination levels of the cleaning solvents during use by electrical conductivity, pH, specific gravity, or water content.
PAGE 12
Aluminum Electrolytic Capacitor 6. Capacitor Disposal When disposing of capacitors, use one of the following methods. ● Incinerate after crushing the capacitor or puncturing the can wall (to prevent explosion due to internal pressure rise). Capacitors should be incinerated at high temperatures to prevent the release of toxic gases such as chlorine from the polyvinyl chloride sleeve, etc. ● Dispose of as solid waste. ● Local laws may have specific disposal requirements which must be followed.