Datasheet

DP-100
15
PRECAUTIONS FOR PROPER USE
PRO mode
Setting item Description
Reset setting
ECO mode setting
Linked display color
switching
(standard type only)
Display refresh rate
switching
Hysteresis fix value
switching
Setting check code
Setting copy mode
Table of codes
—
—
—
————
—
—
—
—
—
—
ADJ.
NO
OFF
OFF
P-1, Lo-1
NC
NO
Hi-1
NO
NC
P-2, Lo-2
NC
NO
Hi-2
NO
NC
NC
NC
NO
EASY
EASY
Analog voltage output /
External input
NO / NC
switching
Comparative output 2
output mode
Comparative output 1
output mode
NO / NC
switching
Display color for
main display
Threshold
value display
Display
color linking
Code
2.5 ms MPa 250 ms OFF
5 ms kPa 500 ms STD
10 ms kgf/cm
2
1,000 ms FULL
25 ms bar
50 ms psi
100 ms mmHg
250 ms inchHg
500 ms
1,000 ms
5,000 ms
Code
If the mode selection key is pressed and held for 5 seconds in
RUN mode, the mode will switch to PRO mode.
If the mode selection key is pressed while a setting is being made,
the mode will switch to RUN mode. In this case, the settings that
have been changed will be entered.


Sub display switching
Changes the information in the sub display
during RUN mode operation to the desired
alphanumeric display.
Changes the display refresh rate for the
pressure value displayed in the main display.
Sets the hysteresis for EASY mode and window
comparator mode. (8 steps)
Allows the display color for the main display to
be switched in line with the output operation for
comparative output 1 or comparative output 2.
Allows power consumption to be reduced by
dimming the display or turning it off.
Allows the setting details to be checked via
codes.
Allows the setting details for the master sensor
to be copied to slave sensors.
Resets the settings to the factory settings.
1st digit
2nd digit
3rd digit
4th digit
Standard
type only
Multi-function
type
Standard type
Hysteresis
Hysteresis
Red
when ON
Comparative
output 1
Comparative
output 2
Comparative
output 1
Comparative
output 2
Comparative
output 1
Comparative
output 2
Comparative
output 1
Comparative
output 2
Green
when ON
Always
red
Always
green
Analog voltage
output
Auto-
reference
Remote
zero-adjustment
Analog current
output
Window
comparator
Window
comparator
5th digit 6th digit 7th digit 8th digit
Response time Unit switching
Display refresh rate
ECO mode
If the mode selection key is pressed and held for 2 seconds in
RUN mode, the mode will switch to MENU SETTING mode.
If the mode selection key is pressed while a setting is being made,
the mode will switch to RUN mode. In this case, the settings that
have been changed will be entered.


Others
RUN mode
MENU SETTING mode
This product has been developed / produced for industrial use.
Use within the rated pressure range.
Do not apply pressure exceeding the pressure withstandability
value. The diaphragm will get damaged and correct operation shall
not be maintained.
Do not use during the initial transient time (0.5 sec. approx.) after
the power supply is switched on.
Avoid dust, dirt, and steam.
Take care that the sensor does not come in direct contact with
water, oil, grease, or organic solvents, such as, thinner, etc.
Do not insert wires, etc., into the pressure port. The diaphragm will
get damaged and correct operation shall not be maintained.
Do not operate the keys with pointed or sharp objects.








7KLVLVWKHQRUPDORSHUDWLQJPRGH
Comparative output 1
output mode setting
Setting item Description
Sets the output mode for comparative output 1.
Unit switching
Pressure unit can be changed.
NO / NC switching
Response time setting
Comparative output 2 output mode
setting (standard type only)
Sets the output mode for comparative output 2.
Display color switching
for main display
Analog output / external
input switching
(multi-function type only)
Allows the color for the main display to be changed.
The colors can be set to ‘red / green’ or ‘green / red’
to correspond to ON / OFF output, or it can be fixed
at ‘red’ or ‘green’ all the time.
Sets the response time.
The response time can be selected from 2.5 ms,
5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms,
500 ms, 1,000 ms and 5,000 ms.
Sets normally open (NO) or normally closed (NC).
Allows switching between analog voltage output /
analog current output, and auto-reference input /
remote zero-adjust-ment input.
Setting item Description
Threshold value
setting
Zero-adjustment
function
Key lock function
Peak hold /
bottom hold function
Stops key operations from being accepted.
The threshold values for ON / OFF operation can be changed directly
by pressing the increment key (UP) and the decrement key (DOWN).
This forces the pressure value display to be reset to zero when
the pressure port is open on the atmospheric pressure side.
Displays the peak value and bottom value for fluctuating
pressure. The peak value appears in the main display,
and the bottom value appears in the sub display.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—