Operating instructions

72
VQT4W64
Other Settings
You can configure the remote control TV operation buttons to turn
the television on/off, change the television input mode, select the
television channel and change the television volume.
1 Point the remote control at the
television
While pressing [Í TV], enter the code
with the numbered buttons.
2 Test by turning on the television and
changing channels.
≥Repeat the procedure until you find the code that allows
correct operation.
≥If your television brand is not listed or if the code listed for
your television does not allow control of your television, this
remote control is not compatible with your television.
≥If your television brand has more than one code listed, select the
one that allows correct operation.
Manufacturer and Code No.
The HOLD function deactivates all buttons on the unit and remote
control. Use it to prevent other people from operating the unit.
Press and hold [OK] and
[RETURN ]
simultaneously until “X
HOLD” appears on the unit’s display.
If you press a button while the HOLD function is on, “X HOLD”
appears on the unit’s display and operation is impossible.
To cancel the HOLD function
Press and hold [OK] and [RETURN ] simultaneously until “X
HOLD” disappears.
Software of CAM (compatible CI Plus) can be upgraded
automatically from broadcasts.
Availability of software upgrade is detected while viewing the
programmes compatible with CI Plus.
When notification is displayed on the screen, select “Yes” and
press [OK].
≥Notice is not displayed in the following cases:
– When recording a programme
– When timer recording and CAM software upgrade occur
simultaneously
– When displaying FUNCTION MENU, DIRECT NAVIGATOR, etc.
≥“CAM-UP” is displayed on the unit’s display during upgrading.
It is also displayed on the Digital Channel Information (> 17) when
the CAM software can be upgraded immediately.
To execute CAM software upgrade, push the “Red” button while the
digital channel information is displayed, and follow the instructions
on the screen.
≥Operations such as view, playback, or record cannot be performed
while upgrading the CAM.
Any buttons on the remote control or the unit cannot be used while
upgrading the CAM.
≥If the timer recording is started, CAM software upgrade is
cancelled to start recording.
≥For details, refer to your CAM’s operating instructions or consult
your dealer.
Television operation
e.g., 01: [0] > [1] 10: [1] > [0]
6
54
3
2
1
CH
CH
PAGE
VOL
AV
DRIVE
SELECT
Í
TV
Í
CH
VOL
AV
Í
Turn TV on/off
Input select
Volume
Channel Select
Note
AIWA 35 MITSUBISHI 05/19/20/47
BEJING 33 NEC 36
BENQ 58/59 NOKIA 25/26/27/60/61
BRANDT 10/15 OLEVIA 45
CENTREX 66 ORION 05
CURTIS 05 PHILCO 41/48/64
DESMET 05 PHONOLA 05
ELEMIS 05 PROVIEW 52
FINLUX 61 RADIOLA 05
FUJITSU 53 SALORA 26
GOLDSTAR 05/50/51 SANSUI 05
GRADIENTE 36 SCHNEIDER 05/29/30
HIKONA 52 SELECO 05/25
INNO HIT 05 SIEMENS 09
ITT 25 SONY 08
JVC 17/30/39/70 TELEFUNKEN 10/11/12/13/14
KOLIN 45 TEX ONDA 52
LG 05/50/51 TOSHIBA 16/57
MAG 52 YAMAHA 18/41
Brand Code Brand Code
05LOEWE
WHITE
WESTINGHOUSE
07/46
Panasonic 01/02/03/04 METZ 05/28/79
AKAI 27/30 MIVAR 24
BEKO 05/71/72/73/74 NOBLEX 33
BP 09 NORDMENDE 10
BUSH 05 ONWA 30/39/70
CHANGHONG 69 PEONY 49/69
DAEWOO 64/65 PHILIPS 05/06/46
DUAL 05 PIONEER 37/38
FERGUSON 10/34 PYE 05
FUNAI 32/42/43/65/6863/67 SAMSUNG
FISHER 21 SABA 10
GOODMANS 05 SANYO 21/54/55/56
GRUNDIG
05/69/75/76/77/78 09 SEG
IRRADIO 30 SINUDYNE 05
JINGXING 31/33/66/67/6949 TCL
KDS 52 TEVION 52
KONKA 62 THOMSON 10/15/44
HITACHI 05/22/23/40/41 SHARP 18
HOLD function
CI Plus compatible CAM (Conditional
Access Module) software upgrade
1 Das Erste
All Channels
18:53
Change Category
CAM Upgrade Info
ZDF-Mor
19:00 - 19:30
NOW
TXT
Note
DMREX96C-VQTXXXX_eng.book 72 ページ ２０１３年３月５日 火曜日 午後５時５１分