Operating Instructions

Troubleshooting
VQT5D92
113
The following messages or service numbers
appear on the unit’s display when something
unusual is detected.
The remote control and main unit are using
different codes. Change the code on the remote
control. (> 107)
CAM is being updated. (> 101)
Selected titles in the USB HDD are being
converted.
Do not disconnect the USB HDD from this unit.
TV Guide data is being downloaded.
If there is no change after switching the unit to
standby mode and turning it on, consult the
dealer.
You cannot delete items on this disc.
The disc may be damaged.
• The disc is dirty. (> 10) The unit cannot record,
play, or edit.
• The lens cleaner has finished cleaning.
Press [< OPEN/CLOSE] on the main unit to
eject the disc.
You cannot write to this disc.
The disc may be damaged. Use a new disc.
• Displayed when the unit is started and is
switched to standby mode.
• There was a power failure or the AC plug was
disconnected while the unit was on. The unit is
carrying out its recovery process. Wait until the
message disappears.
There are already 32 timer programmes. Delete
unnecessary timer programmes. (> 39)
The USB device is drawing too much power.
Remove the USB device.
Update of the software (firmware) is started.
You cannot operate the unit until the update is
complete. (> 101)
Software (firmware) is downloading.
Download will stop when the unit is turned on, or
the timer recording starts. (> 101)
The media is not supported.
Messages on the unit’s display
BD 
(“∑” stands for a number.)
CAM-UP
CONV
GUIDE
HARD ERR
NoERAS
NoREAD
NoWRIT
PLEASE WAIT
PROG FULL
REMOVE
S TA R T
SW-DL
UNSUPPORT
DMR-BCT83_73EN_eng.book 113 ページ ２０１３年７月１８日 木曜日 午前１０時２８分
Fejlnding
Meddelelser på apparatets display
Følgende meddelelser eller servicenumre vises
på apparatets display, når noget usædvanligt
detekteres.
Du kan ikke skrive til disken. Disken kan være
beskadiget. Brug en ny disk.
• Vises, når enheden er i gang og er på vej til
standby tilstand.
•
Der var et strømsvigt, eller netstikket har været
afbrudt, mens enheden var tændt. Enheden er
ved at udføre dens gendannelsesproces
Der er allerede 32 timer-programmer. Slet unød-
vendige timer-programmer. (a 39)
USB enheden trækker for meget strøm.
Fjern USB enheden.
Opdatering af software (firmware) startes.
Du kan ikke betjene apparatet, før opdateringen er
fuldført. (a 101)
Software (firmware) downloader.
Download stopper, når enheden bliver tændt, eller
en timeroptagelsen starter. (a 101)
Medierne er ikke understøttet.
Fjernbetjeningen og hovedenheden anvender
forskellige koder. Skift kode på fjernbetjeningen
enheden. (a 107)
CAM bliver opdateret. (a 101)
Udvalgte titler på USB HDD bliver konverteret.
Du må ikke frakoble USB HDD fra denne enhed.
TV Guide data bliver downloadet.
Hvis der ikke er nogen ændring efter slukning af
apparatet til standby tilstand og tænder den igen,
skal du kontakte forhandler.
Du kan ikke slette elementer på denne disk.
Disken kan være beskadiget.
• Disken er snavset. (a 10) Enheden kan ikke
optage, afspille eller redigere.
•
Linserenser er færdig med rengøringen.
Tryk på [
Troubleshooting
VQT4G51
107
• The unit’s TV System is different from that of the
disc. While stopped, keep pressing [∫] (STOP)
and [< OPEN/CLOSE] on the main unit for 5 or
more seconds. The system switches from PAL
to NTSC or vice versa.
• Picture may not be seen when more than
4 devices are connected with HDMI cables.
Reduce the number of connected devices.
• The picture may be distorted or a black screen
may appear between scenes recorded with
different aspect ratios.
• Set “Deep Colour Output” (> 86, 96) or
“Contents Type Flag” (> 86, 97) to “Off”.
3D video is not output correctly.
• 3D video may be output correctly by changing
the following settings:
- “3D Type” of “3D Settings” (> 96)
- “Signal Format” (> 47, 3D settings during
playback)
• Check the settings of the connected TV.
• When a non-3D compatible amplifier/receiver is
connected between this unit and a TV, 3D video
is not output. (> 18)
• When the amplifier/receiver which is connected
between this unit and a TV is off, 3D video is not
output. (> 18)
• 3D discs may not be played back correctly due
to the settings of the TV.
• When “HDMI Audio Output” is set to “Off”, 3D
video may not be output correctly. (> 96)
No sound.
Distorted sound.
• Check the connections. (> 16)
• Check the settings of the connected TV, etc.
• Press [AUDIO] to select the audio. (> 29, 46)
• To output audio from a device connected with an
HDMI cable, set “HDMI Audio Output” to “On”.
(> 86, 96)
Cannot change audio channel.
• You cannot change the audio channel if “Digital
Audio Output” is set to “Bitstream” (> 94)
The images do not appear on the TV.
The picture is distorted during play, or video
will not play correctly.
• Check the connections. (> 16)
• Check the settings of the connected TV, etc.
• An incorrect resolution is selected in “HDMI
Video Format”. Reset the setting as follows:
1 While the unit is on, press and hold [OK], the
yellow button and the blue button at the
same time for more than 5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “04 PRG”
is displayed on the unit’s display.
3 Press and hold [OK] for at least 3 seconds.
Set the item again. (> 86, 96)
• When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD audio are not output properly,
select “Yes” in “Default Settings” and make
proper settings. (> 86, 101)
The same video is displayed in each left and
right half of the screen.
• This is a 3D programme of the Side-by-Side
type.
Change the setting as follows if connecting with
a 3D compatible TV:
1 Press [OPTION].
2 Select “3D Settings”, then press [OK].
3 Select “Side by side” in “Signal Format”, then
press [OK].
Sound
DMR-BCT820_720_721EG_eng.book 107 ページ ２０１２年８月１日 水曜日 午後５時１８分
OPEN / CLOSE] på hovedenheden
for at skubbe disken ud.
BD 0
(”0” står for et tal.)