Operating Instructions

Fejlnding
Fejlndingsguide
Softwaren (firmware) er ved at blive opdateret.
Du kan ikke betjene apparatet, før opdateringen er
fuldført. (a 96)
UPDATE 0/0
(”0” står for et tal.)
U59
X HOLD
U61
U76
U77
U88
U99
Apparatet er varmt.
Enheden skifter til standby af sikkerhedsmæssige
årsager. Vent i ca. 30 minutter, indtil meddelelsen
forsvinder.
Du må ikke blokere ventilatoren på bagsiden af
enheden.
(Når en disc ikke er isat) En fejl har fundet sted. En-
heden forsøger at gendanne normal drift. Når med-
delelsen forsvinder, kan du bruge enheden igen.
Hvis det forbliver vist, skal du kontakte forhandleren.
HDMI kan ikke vises, fordi det er forbundet med
en model, der ikke understøtter ophavsret beskyt-
telse.
Da den aktuelle disc ikke har autoriseret copyright-
information, er der intet video udgangssignal.
(Når en disc er sat i) Der blev konstateret noget
usædvanlige med disken eller enheden.
Enheden forsøger at gendanne den normale drift.
Når meddelelsen forsvinder, kan du bruge
enheden igen. Hvis det forbliver vist, skal du
kontakte forhandleren.
Enheden ikke fungerer ordentligt. Tryk på [
Troubleshooting
VQT4G51
105
Troubleshooting guide
Troubleshooting
Before requesting service, make the following
checks. If the problem still persists, consult
your dealer for instructions.
Updating to the latest software (firmware) may
solve the problem. (> 102)
The unit is switched to standby mode
automatically.
• VIERA Link or Q Link has worked.
(> 82, Power off link)
The followings do not indicate a problem
with this unit:
• Regular disc rotating sounds or HDD rotating
sounds.
• Poor reception due to atmospheric conditions.
• Image disturbance during search.
• Image disturbance when replacing 3D discs.
• Interruptions in reception due to periodic
broadcasting breaks.
• When you switch the unit on or to standby
mode, there may be an unexpected sound.
General operation
The unit does not work.
• Check the connections. (> 16)
• One of the unit’s safety devices may have been
activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit
to standby.
• If the unit does not switch to standby, press
[Í/I] on the main unit for about 3 seconds.
The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains
lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If
the unit still cannot be operated, consult the
dealer.
Cannot eject a disc.
1 While the unit is in standby mode, press and
hold [OK], the yellow button and the blue
button at the same time for more than
5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “06 FTO” is
displayed on the unit’s display.
3 Press [OK].
DMR-BCT820_720_721EG_eng.book 105 ページ ２０１２年８月１日 水曜日 午後５時１８分
]
på hovedenheden for at skifte til standby.
Tryk nu på [
Troubleshooting
VQT4G51
105
Troubleshooting guide
Troubleshooting
Before requesting service, make the following
checks. If the problem still persists, consult
your dealer for instructions.
Updating to the latest software (firmware) may
solve the problem. (> 102)
The unit is switched to standby mode
automatically.
• VIERA Link or Q Link has worked.
(> 82, Power off link)
The followings do not indicate a problem
with this unit:
• Regular disc rotating sounds or HDD rotating
sounds.
• Poor reception due to atmospheric conditions.
• Image disturbance during search.
• Image disturbance when replacing 3D discs.
• Interruptions in reception due to periodic
broadcasting breaks.
• When you switch the unit on or to standby
mode, there may be an unexpected sound.
General operation
The unit does not work.
• Check the connections. (> 16)
• One of the unit’s safety devices may have been
activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit
to standby.
• If the unit does not switch to standby, press
[Í/I] on the main unit for about 3 seconds.
The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains
lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If
the unit still cannot be operated, consult the
dealer.
Cannot eject a disc.
1 While the unit is in standby mode, press and
hold [OK], the yellow button and the blue
button at the same time for more than
5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “06 FTO” is
displayed on the unit’s display.
3 Press [OK].
DMR-BCT820_720_721EG_eng.book 105 ページ ２０１２年８月１日 水曜日 午後５時１８分
] på hovedenheden for igen at
tænde enheden.
HOLD funktionen er aktiveret. (a 100)
Der er noget usædvanligt. (Det viste service num-
mer efter H og F afhænger af apparatets tilstand.)
Nulstil enheden som følger:
1 Tag stikket ud af stikkontakten, vent et par
sekunder og tilslut den derefter igen.
2 Tryk på [
Troubleshooting
VQT4G51
105
Troubleshooting guide
Troubleshooting
Before requesting service, make the following
checks. If the problem still persists, consult
your dealer for instructions.
Updating to the latest software (firmware) may
solve the problem. (> 102)
The unit is switched to standby mode
automatically.
• VIERA Link or Q Link has worked.
(> 82, Power off link)
The followings do not indicate a problem
with this unit:
• Regular disc rotating sounds or HDD rotating
sounds.
• Poor reception due to atmospheric conditions.
• Image disturbance during search.
• Image disturbance when replacing 3D discs.
• Interruptions in reception due to periodic
broadcasting breaks.
• When you switch the unit on or to standby
mode, there may be an unexpected sound.
General operation
The unit does not work.
• Check the connections. (> 16)
• One of the unit’s safety devices may have been
activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit
to standby.
• If the unit does not switch to standby, press
[Í/I] on the main unit for about 3 seconds.
The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains
lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If
the unit still cannot be operated, consult the
dealer.
Cannot eject a disc.
1 While the unit is in standby mode, press and
hold [OK], the yellow button and the blue
button at the same time for more than
5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “06 FTO” is
displayed on the unit’s display.
3 Press [OK].
DMR-BCT820_720_721EG_eng.book 105 ページ ２０１２年８月１日 水曜日 午後５時１８分
] for at tænde for strømmen.
(Enheden er muligvis klar igen.)
Anmod om service fra forhandleren. Informer
forhandleren om service nummeret, når du
anmoder om service.
H00 eller F00
(”0” står for et tal.)
SQT0351108