Operating Instructions

Fejlnding
Meddelelser på apparatets display
Følgende meddelelser eller servicenumre vises
på apparatets display, når noget usædvanligt
detekteres.
Fjernbetjeningen og hovedenheden anvender
forskellige koder. Skift kode på fjernbetjeningen
enheden. (a 101)
CAM bliver opdateret. (a 96)
Udvalgte titler på USB HDD bliver konverteret.
Du må ikke frakoble USB HDD fra denne enhed.
TV Guide data bliver downloadet.
Hvis der ikke er nogen ændring efter slukning af
apparatet til standby tilstand og tænder den igen,
skal du kontakte forhandler.
Du kan ikke slette elementer på denne disk.
Disken kan være beskadiget.
• Disken er snavset. (a 10) Enheden kan ikke
optage, afspille eller redigere.
•
Linserenser er færdig med rengøringen.
Tryk på [
Troubleshooting
VQT4G51
107
• The unit’s TV System is different from that of the
disc. While stopped, keep pressing [∫] (STOP)
and [< OPEN/CLOSE] on the main unit for 5 or
more seconds. The system switches from PAL
to NTSC or vice versa.
• Picture may not be seen when more than
4 devices are connected with HDMI cables.
Reduce the number of connected devices.
• The picture may be distorted or a black screen
may appear between scenes recorded with
different aspect ratios.
• Set “Deep Colour Output” (> 86, 96) or
“Contents Type Flag” (> 86, 97) to “Off”.
3D video is not output correctly.
• 3D video may be output correctly by changing
the following settings:
- “3D Type” of “3D Settings” (> 96)
- “Signal Format” (> 47, 3D settings during
playback)
• Check the settings of the connected TV.
• When a non-3D compatible amplifier/receiver is
connected between this unit and a TV, 3D video
is not output. (> 18)
• When the amplifier/receiver which is connected
between this unit and a TV is off, 3D video is not
output. (> 18)
• 3D discs may not be played back correctly due
to the settings of the TV.
• When “HDMI Audio Output” is set to “Off”, 3D
video may not be output correctly. (> 96)
No sound.
Distorted sound.
• Check the connections. (> 16)
• Check the settings of the connected TV, etc.
• Press [AUDIO] to select the audio. (> 29, 46)
• To output audio from a device connected with an
HDMI cable, set “HDMI Audio Output” to “On”.
(> 86, 96)
Cannot change audio channel.
• You cannot change the audio channel if “Digital
Audio Output” is set to “Bitstream” (> 94)
The images do not appear on the TV.
The picture is distorted during play, or video
will not play correctly.
• Check the connections. (> 16)
• Check the settings of the connected TV, etc.
• An incorrect resolution is selected in “HDMI
Video Format”. Reset the setting as follows:
1 While the unit is on, press and hold [OK], the
yellow button and the blue button at the
same time for more than 5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “04 PRG”
is displayed on the unit’s display.
3 Press and hold [OK] for at least 3 seconds.
Set the item again. (> 86, 96)
• When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD audio are not output properly,
select “Yes” in “Default Settings” and make
proper settings. (> 86, 101)
The same video is displayed in each left and
right half of the screen.
• This is a 3D programme of the Side-by-Side
type.
Change the setting as follows if connecting with
a 3D compatible TV:
1 Press [OPTION].
2 Select “3D Settings”, then press [OK].
3 Select “Side by side” in “Signal Format”, then
press [OK].
Sound
DMR-BCT820_720_721EG_eng.book 107 ページ ２０１２年８月１日 水曜日 午後５時１８分
OPEN / CLOSE] på hovedenheden
for at skubbe disken ud.
BD 0
(”0” står for et tal.)
CAM Upgrade
No WRITE
Please Wait
Programme Full
Remove
Start
SW-DL
Unsupport
Conversion
GUIDE
Hard Error
No ERASE
No READ
Du kan ikke skrive til disken. Disken kan være
beskadiget. Brug en ny disk.
• Vises, når enheden er i gang og er på vej til
standby tilstand.
•
Der var et strømsvigt, eller netstikket har været
afbrudt, mens enheden var tændt. Enheden er
ved at udføre dens gendannelsesproces
Der er allerede 32 timer-programmer. Slet unød-
vendige timer-programmer. (a 37)
USB enheden trækker for meget strøm.
Fjern USB enheden.
Opdatering af software (firmware) startes.
Du kan ikke betjene apparatet, før opdateringen er
fuldført. (a 96)
Software (firmware) downloader.
Download stopper, når enheden bliver tændt, eller
en timeroptagelsen starter. (a 96)
Medierne er ikke understøttet.
SQT0351 107