Operating Instructions

Troubleshooting
SQT0351
101
Troubleshooting guide
Troubleshooting
Before requesting service, make the following
checks. If the problem still persists, consult
your dealer for instructions.
Updating to the latest software (firmware) may
solve the problem. (> 96)
The unit is switched to standby mode
automatically.
• VIERA Link has worked. (> 79, Power off link)
The remote control does not work.
• The remote control and main unit are using
different codes. Change the code on the remote
control.
• Software (firmware) is updating when “UPDATE
/” is displaying on the front panel display.
Wait until the update is completed. (> 96)
• The HOLD function is activated. (> 100)
• Startup of this unit may be slower depending on
the TV settings.
“0:00” is flashing on the front panel display.
• Set the clock. (> 82, 94)
The clock does not display on the unit when
switched to standby.
• The clock does not display when “Front Panel
Display” is set to “Automatic”. (> 89)
The followings do not indicate a problem
with this unit:
• Regular disc rotating sounds or HDD rotating
sounds.
• Poor reception due to atmospheric conditions.
• Image disturbance during search.
• Image disturbance when replacing 3D discs.
• Interruptions in reception due to periodic
broadcasting breaks.
• When you switch the unit on or to standby
mode, there may be an unexpected sound.
General operation
The unit does not work.
• Check the connections. (> 16)
• One of the unit’s safety devices may have been
activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit
to standby.
• If the unit does not switch to standby, press
[Í/I] on the main unit for about 3 seconds.
The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains
lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If
the unit still cannot be operated, consult the
dealer.
Cannot eject a disc.
1 While the unit is in standby mode, press and
hold [OK], the yellow button and the blue
button at the same time for more than
5 seconds.
• “00 RET” is displayed on the front panel
display.
2 Repeatedly press [1] (right) until “06 FTO” is
displayed on the front panel display.
3 Press [OK].
Front panel display
Press and hold [OK] and the indicated number
button at the same time for more than
5 seconds. (> 94)
Startup is slow.
• Startup takes time in the following situations:
- A disc is inserted.
- The clock is not set.
- Immediately after a power failure or the AC
mains lead is connected.
- When a BD-J application is executing.
- When the “Quick Start” is not activated. (> 93)
Displays
DMR-BCT84_74EN_eng.book 101 ページ ２０１４年７月２４日 木曜日 午後５時３分
Fejlnding
Fejlndingsguide
Før du anmoder om service, skal følgende kon-
trolleres. Hvis problemet stadig fortsætter, skal
du kontakte din forhandler for at få vejledning.
Opdatering til den nyeste software (firmware)
kan måske løse problemet. (a 96)
Generel betjening
Displays
Enheden fungerer ikke.
• Kontroller tilslutningerne. (a 16)
• En af apparatets sikkerhedsanordninger kan
have været aktiveret.
Nulstil enheden som følger:
1 Tryk på [
Troubleshooting
VQT4G51
105
Troubleshooting guide
Troubleshooting
Before requesting service, make the following
checks. If the problem still persists, consult
your dealer for instructions.
Updating to the latest software (firmware) may
solve the problem. (> 102)
The unit is switched to standby mode
automatically.
• VIERA Link or Q Link has worked.
(> 82, Power off link)
The followings do not indicate a problem
with this unit:
• Regular disc rotating sounds or HDD rotating
sounds.
• Poor reception due to atmospheric conditions.
• Image disturbance during search.
• Image disturbance when replacing 3D discs.
• Interruptions in reception due to periodic
broadcasting breaks.
• When you switch the unit on or to standby
mode, there may be an unexpected sound.
General operation
The unit does not work.
• Check the connections. (> 16)
• One of the unit’s safety devices may have been
activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit
to standby.
• If the unit does not switch to standby, press
[Í/I] on the main unit for about 3 seconds.
The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains
lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If
the unit still cannot be operated, consult the
dealer.
Cannot eject a disc.
1 While the unit is in standby mode, press and
hold [OK], the yellow button and the blue
button at the same time for more than
5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “06 FTO” is
displayed on the unit’s display.
3 Press [OK].
DMR-BCT820_720_721EG_eng.book 105 ページ ２０１２年８月１日 水曜日 午後５時１８分
] på hovedenheden for at
sætte enheden i standby.
• Hvis apparatet ikke skifter til standby, skal
du trykke [
Troubleshooting
VQT4G51
105
Troubleshooting guide
Troubleshooting
Before requesting service, make the following
checks. If the problem still persists, consult
your dealer for instructions.
Updating to the latest software (firmware) may
solve the problem. (> 102)
The unit is switched to standby mode
automatically.
• VIERA Link or Q Link has worked.
(> 82, Power off link)
The followings do not indicate a problem
with this unit:
• Regular disc rotating sounds or HDD rotating
sounds.
• Poor reception due to atmospheric conditions.
• Image disturbance during search.
• Image disturbance when replacing 3D discs.
• Interruptions in reception due to periodic
broadcasting breaks.
• When you switch the unit on or to standby
mode, there may be an unexpected sound.
General operation
The unit does not work.
• Check the connections. (> 16)
• One of the unit’s safety devices may have been
activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit
to standby.
• If the unit does not switch to standby, press
[Í/I] on the main unit for about 3 seconds.
The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains
lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If
the unit still cannot be operated, consult the
dealer.
Cannot eject a disc.
1 While the unit is in standby mode, press and
hold [OK], the yellow button and the blue
button at the same time for more than
5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “06 FTO” is
displayed on the unit’s display.
3 Press [OK].
DMR-BCT820_720_721EG_eng.book 105 ページ ２０１２年８月１日 水曜日 午後５時１８分
] på hovedenheden i
omkring 3 sekunder. Enheden tvinges til
standby. Alternativt kan du afbryde AC-
ledningen, vent et minut, og tilslut den igen.
2 Tryk på [
Troubleshooting
VQT4G51
105
Troubleshooting guide
Troubleshooting
Before requesting service, make the following
checks. If the problem still persists, consult
your dealer for instructions.
Updating to the latest software (firmware) may
solve the problem. (> 102)
The unit is switched to standby mode
automatically.
• VIERA Link or Q Link has worked.
(> 82, Power off link)
The followings do not indicate a problem
with this unit:
• Regular disc rotating sounds or HDD rotating
sounds.
• Poor reception due to atmospheric conditions.
• Image disturbance during search.
• Image disturbance when replacing 3D discs.
• Interruptions in reception due to periodic
broadcasting breaks.
• When you switch the unit on or to standby
mode, there may be an unexpected sound.
General operation
The unit does not work.
• Check the connections. (> 16)
• One of the unit’s safety devices may have been
activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit
to standby.
• If the unit does not switch to standby, press
[Í/I] on the main unit for about 3 seconds.
The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains
lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If
the unit still cannot be operated, consult the
dealer.
Cannot eject a disc.
1 While the unit is in standby mode, press and
hold [OK], the yellow button and the blue
button at the same time for more than
5 seconds.
• “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) until “06 FTO” is
displayed on the unit’s display.
3 Press [OK].
DMR-BCT820_720_721EG_eng.book 105 ページ ２０１２年８月１日 水曜日 午後５時１８分
] på hovedenheden for at
tænde den. Hvis enheden stadig ikke kan
betjenes, skal du kontakte din forhandler.
Kan ikke eject en disk.
1 Mens enheden er i standby, skal du trykke og
Holde [OK], den gule knap og den blå knap
samtidig i mere end 5 sekunder.
• “00 RET” vises på apparatets display.
2 Tryk gentagne gange på [►] (til højre), indtil
“06 FTO” vises på apparatets display.
3 Tryk på [OK].
Enheden skifter til standby automatisk.
• VIERA Link er udført.
(a 79, Power off link)
Følgende indikerer ikke et problem med denne
enhed:
• Regelmæssige disc roterings lyde eller HDD
roterings lyde.
• Dårlig modtagelse på grund af atmosfæriske
forhold.
• Billed forstyrrelse under søgning.
• Billed forstyrrelse ved udskiftning 3D-diske.
• Afbrydelser i modtagelse på grund af periodiske
udsendelse pauser.
• Når du tænder for apparatet eller sætter det i
standby tilstand, kan der være en uventet lyd.
Fjernbetjeningen virker ikke.
• Fjernbetjeningen og hovedenheden anvender
forskellige koder. Skift kode på fjernbetjeningen.
Enhedens display
Tryk og hold [OK], og knappen for det valgte tal
samtidigt i mere end 5 sekunder. (a 94)
• Software (firmware) er ved at opdatere, når
“UPDATE 0/0” vises på apparatets display.
Afvent opdateringen er fuldført. (a 96)
• HOLD-funktionen er aktiveret. (a 100)
Opstart er langsom.
• Opstart tager tid i følgende situationer:
- En disc er indsat.
- Uret er ikke indstillet.
- Umiddelbart efter en strømafbrydelse eller AC
netledningen er tilsluttet.
- Når en BD-J applikation afvikles.
- Når “Power Save i Standby” er aktiveret.
(a 93)
• Denne enheds opstart kan være langsommere,
afhængigt af TV-indstillingerne.
“0:00” blinker på apparatets display.
• Indstil uret. (a 82, 94)
Uret vises ikke på enheden, under standby.
• Uret vises ikke, når “Unit Display” er indstillet til
“Automatic”. (a 89)
SQT0351 101