Operating Instructions
2
Selecting the desired focus area and
saving a picture
1
Recording with the Post Focus
function
2
Selecting pictures from 6K/4K burst fi le and saving
Battery drainage and camera temperature
When the ambient temperature is high or 6K/4K photo recording is performed continuously, the camera may display [ ] and recording may stop. If you
are using [6K/4K Pre-Burst], the setting will switch to [6K/4K Burst] and recording will stop. Wait until the camera cools down.
When [6K/4K Pre-Burst] or [Pre-Burst Recording] is set, the battery drains faster and the camera temperature rises. Use these functions only when
recording with them.
Setting Pre-Burst Recording ([6K/4K Burst]/[6K/4K Burst(S/S)] only)
MENU
[Rec] [6K/4K PHOTO] [Pre-Burst Recording] [ON]
The camera starts recording approximately 1 second before the shutter button is pressed fully, so you will not miss a photo opportunity.
Press [ 1 ] .
Press
2 /to select an image indicated with the [ ]/[ ] icon.
Press the cursor button
3 .
If the image was recorded with [6K/4K Pre-Burst], proceed to step 5.
Drag the slide bar to make a rough selection of scenes.4
Drag the frames to select the frame you want to save as a picture.5
Touch [6 ]/[ ] to save the picture.
A confi rmation screen will be displayed.
The picture will be saved in JPEG format.
Correcting 6K/4K Photos After Recording (Post-Recording Refi nement)
Correcting distortion in pictures ([Reduce Rolling Shutter])
On the save confi rmation screen in step
6, touch [Reduce Rolling Shutter].
Check the correction result, and touch [Save].
Fn2
Fn1
Reducing the noise produced by high sensitivity ([6K/4K PHOTO Noise Reduction])
MENU
[Playback] [6K/4K PHOTO Noise Reduction] [AUTO]
When saving pictures, reduce the noise produced during recording by high ISO sensitivity.
The camera can perform Burst recording in the same picture quality as 6K/4K photo recording while automatically shifting the focus to different areas.
After the recording, you can select the desired area on the screen and save a picture in which the selected area is in focus.
Controlling Focus After Recording (Post Focus/Focus Stacking)
We recommend that you use a tripod when recording images to be used for
Focus Stacking.
Set the drive mode dial to [ 1 ] (Post Focus).
Decide on the composition, and press the
2
shutter button halfway.
Press the shutter button fully to start
3
recording.
Selecting the picture size
MENU
[Rec] [Post Focus] [6K 18M]/[4K 8M]
Press [ 1 ] .
Press
2 /to select an image
indicated with the [
] icon, and
press the cursor button .
Touch the desired focus area.3
If a picture that is in focus is not available for
the selected area, a red frame will be displayed.
You cannot save a picture in this case.
Touch [ 4 ] to save the picture.
The picture will be saved in JPEG format.
Fn2
Fn1
3
Using Focus Stacking and saving a picture
You can also merge multiple pictures with different focus areas to widen the focus range. (Focus Stacking)
Touch [ 1 ] (Fn1) in step 3 of “Selecting the desired focus area and saving a picture”.
Touch the merging method.
2
[Auto Merging]
Automatically selects pictures that are suited to be merged, and merges them into a single picture.
[Range Merging]
Merges pictures with specifi ed focus areas into a single picture.
(When [Range Merging] is selected) Touch the desired focus area.3
Specify at least two areas.
In-focus areas between the two areas will also be selected, and the combined in-focus area will be
indicated.
Grey areas indicate areas that may, if selected, cause the merged picture to look unnatural and areas
that cannot be selected.
To cancel the selection, touch the focus area again.
Touch [ 4 ] to merge the pictures and save the resulting picture.
The picture will be saved in JPEG format.
ュリヴヱハ
5HVHW
Fn1
6HW&DQFHO
Fn1
ュリヴヱハ
5HVHW
6HW&DQFHO
DC-G9DVQW12576K4KPHOTOEBGNeng.indd2DC-G9DVQW12576K4KPHOTOEBGNeng.indd2 2017/11/0621:23:092017/11/0621:23:09