In-Dash 7” Widescreen Color LCD Monitor/DVD Receiver In-Dash 7-Zoll Breitbild-LCD-Farbmonitor/DVD-Receiver Moniteur vidéo couleur grand-écran à écran à cristaux liquides de 7 pouces/récepteur DVD intégrés en tableau de bord In het dashboard gemonteerde 7” breedbeeld kleuren LCD monitor/DVD-receiver Sintolettore DVD con monitor a colori LCD 7” a schermo panoramico da cruscotto Monitor LCD en color de pantalla panorámica de 7”/receptor y DVD empotrado en el tablero de instrumentos TILT CLOSE Model: CQ-VD70
English Safety Information 1 ■ Read the operating instructions for the unit and all other components of your car audio system carefully before using the system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual. Warning This pictograph intends to alert you to the presence of important operating instructions and installation instructions.
Observe the following cautions when using this unit. ❑ Keep the sound volume at an appropriate level. Keep the volume level low enough to be aware of road and traffic conditions while driving. ❑ Do not insert or allow your hand or fingers to be caught in the unit. To prevent injury, do not get your hand or fingers caught in moving parts or in the disc slot. Especially watch out for infants. ❑ This unit is designed for use exclusively in automobiles.
English Safety Information (continued) Laser Product Label Indications and Their Locations 3 CLASS 1 LASER PRODUCT CAUTION LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM. Caution Label CAUTION - LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. Caution: This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not take apart this unit or attempt to make any changes yourself.
Liquid Crystal Panel ¡Do not cause impact to the liquid crystal panel. ¡Usage temperature range: 0 °C to 40 °C When the temperature is very cold or very hot, the image may not appear clearly or may move slowly. Also, movement of the image may seem to be out of synchronization or the image quality may decline in such environments. Note that this is not a malfunction or problem. ¡In order to protect the liquid crystal panel, keep it out of direct sunlight while the unit is not in use.
English Features Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company.
Contents English 2 Deutsch 56 Français 110 Nederlands 164 Italiano 218 Español 272 ¢ Safety Information .......................... 2 ¢ Notes on Use ................................................... 5 ¢ Components .................................................... 5 ¢ Features ........................................................... 6 ¢ Contents .......................................................... 7 ¢ Preparation......................................
English Preparation 7 First Time Power On The speaker setup screen appears after the opening display when the power is turned on for the first time. Perform speaker setup according to the car conditions in which this unit is installed. ( SP SETUP a page 38) Remote Control Unit Before Initial Use Pull the insulation film out from the backside of the remote control gently.
English Symbols used in this manual Pictographs Disc Marks You can perform some operations of this unit in one or more methods with the touch panel or remote control. This book explains such operations in tabular form as follows. Refer to the following for the pictographs located in the upper part of each table. The following pictographs are used for the descriptions of disc operation.
English Name of Controls and Functions 9 !0 [TILT] o [OPEN] (CLOSE) Main Unit (Display Raised) TILT CLOSE q [ASP] (ASPECT P•MODE (PRIVATE MODE) ) Display Remote control sensor Disc slot i w [VOL] [}] [{] (DISC) [] ] [[ ] (TUNE/TRACK) OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE CQ-VD7001U VOL [ENTER] ENTER MUTE e [MUTE] PWR SRC TA NAVI u [u] r [SRC] (PWR) (SOURCE/POWER) t [TA] y [NAVI] Main Unit Dimmer sensor ( (Display Closed) DIMMER a page 36) !0 [TILT] ASPECT A
English Remote Control Aim the remote control at the remote control sensor of the main unit and operate it. 10 q [SRC] (PWR) (SOURCE/POWER) r [MUTE] PWR t [+] [–] (VOL) MUTE SRC VOL w [■] [❚❚] [B] ENTER / BAND ENT [s] [d] TOP MENU e [RET] (RETURN) RET RETURN DVD MENU y [}] [{] [] ] [[ ] [ENT](ENTER/BAND) u[ Note: ¡[ENT], [RET], [■], [❚❚], [B], [ ] (TOP MENU/DVD MENU) CAR AV ] are available only on the remote control unit. q [SRC] (PWR) ¡Switches the power on/off.
English Touch Panel Operation Overview 11 ❒ Notes on the Touch Panel Before operation ¡Clean the surface of the touch panel. (a page 51) Operation ¡Use only your fingers to operate the touch panel. ¡Do not press the panel forcefully. ¡Do not scratch the panel with fingernails or any hard objects. ¡Do not use a pen or other sharp implements to operate the touch panel. ¡Do not bump the front panel. a Failure to observe the above may damage or break the glass on the surface of the touch panel.
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are connected. English Switching the display 12 Touching allows users to switch between screens as follows.
English General [VOL] ASPECT ASP TILT TILT P·MODE 13 [OPEN] [TILT] OPEN OPEN CQ-VD7005N VOL ENTER MUTE MUTE [MUTE] PWR SRC TA NAVI [] ] [[ ] [SRC] (PWR: power) Remote Control Sensor Preparation: Turn your car’s ignition key to the ACC or ON position. General Operations Operations Power – [SRC] OFF : – [SRC] [SRC] Note: ¡You cannot turn on the power via the remote control when ACC SELECT is set to OFF .
[MUTE] English [+] [–] (VOL) 14 [SRC] (PWR: power) PWR MUTE SRC VOL ENTER / BAND ENT [] ] [[ ] TOP MENU RET RETURN DVD MENU CAR AV General Operations (continued) Operations Volume Note: ¡The sound level for each source is stored in memory. q [+] w [–] – END DVD VTR RADIO CH-C w q q Up w Down Setting Range: –82 dB to 0 dB, default: –40 dB Note: ¡ The volume level can be set independently for each source and each disc format. Mutes the sound. To cancel, press again.
English Before Disc Playback Discs that can be Played Back ❒ Disc Type ❒ Symbols used on jackets 15 DISC DVD (Examples of such symbols include) VCD (Video CD) CD Mark/logo TEXT Disc Size Region No. LPCM, MPEG1 : Number of audio tracks ReWr itable ¡ : Number of angles 3 The numbers indicate the number of languages, tracks, angles, etc., recorded on the disc.
English Disc Insert/Eject ■ When a disc is in the player... 16 TILT CLOSE Printed side OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT TEXT P·MODE CQ-VD7001U [u] (eject) lights. VOL Caution MUTE ¡When the disc is inserted or ejected, to prevent disc scratches never exert any downward force on the disc. Disc Insert DVD VCD CD MP3 WMA CH-C ¡The mode that supports the disc is selected, and playback starts. DVD VCD CD MP3 WMA CH-C ¡The audio format is automatically identified.
English Disc Player Disc Mode (DVD) Selection Source Button q Touch “Source Button”. d TILT CLOSE w Touch (DVD) on the Source Selection Screen. 17 OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE CQ-VD7001U VOL Press [SRC] to change to the desired mode. To switch Operation Screen ON, touch the centre of touch panel or press [ENTER].
English Basic Operations Operations Operations Compatible Discs 18 Track (chapter)/file Selection DVD VCD [d] CD [s] MP3 WMA DVD Fast Forward/ Fast Reverse DVD VCD CD MP3 WMA DVD VCD Folder Selection MP3 WMA Title/text Scroll END DVD VTR RADIO CH-C [[] Next track/file []] Beginning of the current track/file Previous track/file (Touch/press twice.) Note: ¡When playing a DVD, there are cases where it is not possible to return to the start of a chapter that spans 2 titles.
English Disc Player (continued) To switch Operation Screen ON, touch the centre of touch panel or press [ENTER]. Chapter/title Selection Operations Operations 19 Compatible Discs Showing menu and selecting an item *1 Note on VCD: For VCD, touch/press / [RETURN] instead of / [DVD MENU]. or [DVD MENU] or [RETURN]*1 – q Menu appears. END *1 d DVD VCD *1 DVD VTR RADIO CH-C –*2 d –*2 d [] ] [[ ] [] ] [[ ] [}] [{] [}] [{] d d [ENTER] [ENTER] – [RETURN] – d w Select the desired item.
English DVD mode display 20 Repeat play DVD menu Return Chapter/title selection Fast forward/fast reverse Play/stop/pause Audio language/ Angle/ Subtitle language Useful Function Operations Operations Compatible Discs Subtitle Language – – ¡Touch during playback. END DVD It is possible to change the subtitle language during play if multiple languages are recorded on the disc. Note: ¡There may be a brief delay before the subtitles appear.
English Notes on MP3/WMA 21 What is MP3/WMA? Display Information MP3* (MPEG Audio Layer-3) and WMA (Windows Media Audio) are the compression formats of digital audio. The former is developed by MPEG (Motion Picture Experts Group), and the latter is developed by Microsoft Corporation.
¡ You may encounter trouble in playing MP3/WMA files or displaying the information of MP3/WMA files recorded with certain writing software or CD recorders. ¡ This unit does not have a play list function. ¡ Although Multi-session recording is supported, the use of Disc-at-Once is recommended. English RecordingRecording MP3/WMA MP3/WMA files on files a on CD-media a CD-media ¡ You are recommended to minimize the chances of making a disc that contains both CD-DA files and MP3/WMA files.
English Radio Radio Mode Selection q Touch “Source Button”. Auto presetting Preset stations Frequency Source Button TILT CLOSE d w Touch (RADIO) on the Source Selection Screen. 23 Band selection OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE Press [SRC] to change to the desired mode. To switch Operation Screen ON, touch CQ-VD7001U VOL ENTER PWR SRC SRC MUTE *1 List selection . NAVI TA [SRC] [ENTER] Tuning [] ] [[ ] Stereo indicator *1 Appears when ALL is selected.
English Preset Memory Manual Preset Memory Up to 6 stations can be preset in each band. Select a band and frequency. to – – blinks once 24 ¡Touch/press and hold for more than 2 seconds. ¡The frequency blinks once, and a receiving station is saved in the memory. New stations overwrite existing saved stations. Auto Preset Memory Preparation: Select A Select a band. MENU Six stations are automatically preset in each band. e RADIO e [BAND] EACH .
English RDS (Radio Data System) PTY/PS display TILT CLOSE PTY preset 25 AF on/off setting PTY on/off setting OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE CQ-VD7001U VOL ENTER MUTE Current state PWR SRC TA TA NAVI [TA] RDS Basics Some FM stations are broadcasting added data compatible with RDS. This radio set offers convenient functions using such data. RDS service availability varies with areas.
TILT CLOSE OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE CQ-VD7001U VOL ENTER MUTE PWR SRC TA TA [TA] NAVI TA on/off (Only for the button [TA] on the player) Press [TA] to switch TA mode as follows. TA ON : Receive traffic programmes automatically. TA OFF : TA is not active. The following functions are available when the TA mode is active.
English RDS (Radio Data System) (continued) ❏ PTY (Programme Type) TILT CLOSE PTY/PS display 27 PTY preset PTY on/off setting OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE CQ-VD7001U [ENTER] VOL ENTER MUTE PWR SRC TA NAVI [] ] [[ ] PTY on/off Touch PTY ON PTY Preset Call to switch PTY ON/OFF. : PTY display mode The following functions are activated. Programme types are stored in memory under the preset buttons (1) to (6) shown in the table below.
English ❏ MENU Operation on RDS Refer to “Settings” for further information regarding other items on the menu. (a page 32) 28 Opening the RDS menu q Touch w . Touch e . Touch . Example: Radio mode RDS SETUP PTY (PTY on/off setting) Setting for RDS (Radio Data System) AF (Alternative frequency) ON : AF, Best Station Research and PI seek function are active. OFF : When the AF network of an RDS station is not required.
English AV1/AV2 29 Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are connected. Preparation: ¡Connect an optional external device to the AV1/AV2. AV Mode Selection Source Button You can view the images and listen to the sounds from the connected external devices in the AV1/AV2 mode respectively. TILT CLOSE q Touch “Source Button”. d / w Touch (AV1/AV2) on the Source Selection Screen.
English 30 CQ-VD7005N 31
English Settings 31 USER DISPLAY UNIT CLOCK ID-CODE MEMORY CLEAR OTHER User Display adjustment Clock setting ID Code Setting Memory clearance Other settings (a page 34) (a page 34) (a page 34) (a page 35) (a page 35) SCREEN DIMMER PICTURE Screen Adjusting the brightness Display appearance (a page 36) (a page 36) AUDIO SOUND SETUP GRAPHIC-EQ CS Auto SP SETUP SP LEVEL TIME ALIGNMENT SOURCE LEVEL CROSS OVER Audio Sound setting Setting and adjusting of graphic equalizer CS Auto setting Setting of the a
English ❏ MENU Operation (Example: DVD mode) q w Touch e 32 Touch desired setting. in Operation Screen. (Example: setting screen of DISPLAY UNIT a page 34) Determines the setting and goes back to the previous menu out of the menu. Determines the setting and gets out of the menu. Note: ¡ The display returns to the previous status if there is no operation for more than 60 seconds after changing to the setting menu.
English Settings (continued) 33 USER SCREEN AUDIO DVD INPUT/OUTPUT RADIO MINUTE ADJUST DISPLAY UNIT Display adjustment ] : puts back minute TILT 1 2 (Tilt angle adjustment) 3 (Minute adjustment) 4 5 [ : puts forward minute 1 5 Note: /[SRC]. ¡To start the clock, touch/press ¡Set the Daylight Saving Time manually.
English OTHER Caution ¡Record your registered ID code and keep it in a secure location. (Fill in the ID code memo (a page 50).) If you forget it, you will be unable to use the unit. In case you forget the ID code, please consult your nearest Panasonic Service Centre. 34 Other settings BEEP (Beep setting) ON : operation sound (beep) ON OFF : operation sound (beep) OFF default: MEMORY CLEAR ON Memory clearance The state of all of the current memories are returned to default settings.
English Settings (continued) 35 SCREEN USER AUDIO DVD INPUT/OUTPUT RADIO USER SCREEN AUDIO DVD INPUT/OUTPUT RADIO (Display) SOUND SETUP DIMMER Sound Set Up Adjusting the brightness AUTO 1 : automatically adjusted according to ambient light intensity.
English (flat) ¡To set the level to flat, touch and hold for more than 2 seconds. ¡Expectable effects vary with the audio format to be used, settings in the menu, and other factors.
English Settings (continued) 37 (AUDIO continued) PHASE SP SETUP (Speaker set up) Setting the absence/presence and size of each speaker FRONT (Front speaker setting) 0° 180° SMALL : for small speakers, or when bass playback is not possible (Phase setting) : subwoofer phase 0 degree : subwoofer phase 180-degree inverted Note: ¡This setting is feasible only when YES .
English Note: ¡While the private mode is active, only FRONT L and FRONT R can be adjusted. SOURCE LEVEL Setting the AV1/AV2 input level Make this setting if it is not possible to adjust the volume through the connected device (on the output side). AV1 LEVEL TEST TONE : enables the test tone OFF : disables the test tone OFF ¡When the test tone is set to on, test signal (a continuous tone) is output from each speaker for approximately 2 seconds.
English Settings (continued) 39 USER SCREEN AUDIO DVD INPUT/OUTPUT RADIO LANGUAGE DISPLAY Language Setting MENU EN FR SP GE IT OTHER Display aspect and DVD software mode (DVD menu language) NARROW WIDE : English : French : plays a video in wide screen (16:9). default: : Italian : other language. Input the language code. (a page 53) default: EN (Subtitle language) : English : French : Spanish : German : Italian : other language. Input the language code.
SCREEN AUDIO DVD ON OFF RADIO NAVI SETUP (Navigation set up) DVD SOUND DVD sound setting PRO LOGIC INPUT/OUTPUT (a System Upgrade Guidebook) (5.1 channel listening in Dolby surround sound) : activates Pro Logic. English USER 40 SOURCE SKIP Source skip AV1 SKIP (AV1 skip) : inactivates Pro Logic. default: OFF Note: ¡This setting is enabled only in the DVD/VCD/CD player mode. ¡ ON selection in some audio settings may disable audio output from the subwoofer.
English Settings (continued) 41 USER SCREEN AUDIO RADIO DVD INPUT/OUTPUT FM SETUP RDS SETUP (a page 29) Setting for FM stations NOISE SUPPRESSION AUTO (FM IF filter switching) : adjusted automatically NARROW : narrows the frequency bandwidth to be received to prioritize noise reduction. WIDE : widens the frequency bandwidth to be received to prioritize sound quality. default: AUTO PRESET AUTO (Auto preset setting) EACH : saves the preset stations in each band.
English [ASP] TILT CLOSE 42 OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE CQ-VD7001U VOL ENTER MUTE PWR SRC TA NAVI ❑ Aspect Ratio Default: NORMAL Mode: 4 types Press and hold [ASP] on the display unit to change the aspect ratio as follows. NORMAL ¡The conventional display image has a 4 to 3 ratio of horizontal to vertical. ¡In this case, a blank area remains on the right and left sides of the display.
English Settings (continued) [ASP] (P•MODE) TILT CLOSE 43 OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE CQ-VD7001U VOL ENTER MUTE PWR SRC TA NAVI ❑ Private Mode You can mute the sounds from the rear speakers if necessary. Activation of the private mode allows you to enjoy the front monitor and rear monitor independently with different sources at the same time. Default: Private mode off “P • MODE” indicator lights when the Private Mode is activated.
❑ If You Suspect Something Wrong Check and take steps as described below. If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Service Centre. The product should be serviced only by qualified personnel. Please refer checking and repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking.
English Troubleshooting (continued) 45 ■ Radio Poor reception or noise Antenna installation or wiring of antenna cable is faulty. aCheck whether the antenna mounting position and its wiring are correct. In addition, check to see whether the antenna ground is securely connected to the chassis. No power is supplied to the antenna amplifier (when using a film antenna, etc.). aCheck the wiring of the antenna power lead. FM Stereo broadcast is received only in mono. The MONO mode is active.
English ■ CD No playback or disc ejected Sound skipping or noise Sound skipping due to vibration Disc unejectable The disc is inserted upside down. aInsert a disc correctly. 46 There is a flaw or foreign object on the disc. aRemove the foreign object, or use a flawless disc. There is a flaw or foreign object on the disc. aRemove the foreign object, or use a flawless disc. The unit is not sufficiently secured. aSecure the unit to the console box.
English Troubleshooting (continued) 47 ■ DVD Cannot switch the audio language/subtitle language/angle. ¡It is not possible to switch if the disc does not have multiple audio languages/subtitle languages/angles recorded on it. (Refer to the guide provided with your disc.) ¡Some discs permit switching through a menu screen. ¡Sometimes, switching angles is possible only with certain scenes. The audio/subtitle language selected in the DVD settings is not used.
The battery is inserted in the wrong direction. A wrong battery is inserted. aInsert a correct battery in the correct direction. 48 The battery is weak. aReplace the battery with new one. No response to pressing buttons English ■ Remote control unit The aiming direction of the remote control unit is wrong. aAim the remote control unit at the sensor of the unit and press buttons. The sensor is exposed to direct sunlight.
English Troubleshooting (continued) 49 ❑ Error Display Messages ■ CD/MP3/WMA/DVD/VCD (Video CD) Display Possible cause a Possible solution NON PLAYABLE DISC MECHANISM ERROR Disc is dirty, or is upside down. aCheck disc. Disc has scratches. aCheck disc. No operation by some cause. aPress [u]. If failure persists, press the reset switch. If normal operation is not restored, call the store where you purchased the unit or the nearest Panasonic Service Centre.
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic Service Centre. The product should be serviced only by a qualified technician. ❑ Replacing the Fuse Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher rating, or connecting the product directly without a fuse, could cause fire or damage to this unit. If the replacement fuse fails, contact your nearest Panasonic Service Centre for service.
English Notes on Discs 51 How to hold the disc ¡Do not touch the underside of the disc. ¡Do not scratch the disc. ¡Do not bend disc. ¡When not in use, keep disc in the case. Printed side Do not use discs that fit any of the descriptions given below. Using these discs may damage the discs or cause the unit to malfunction.
In “OTHER” cases... (a page 40) Input the four digit language code pressing the buttons Touch to determine. DVD language menu (a page 40) to . Note: ¡Setting is finished and the display returns to the main menu. /[RETURN].
English Definition of Terms 53 Dolby Digital This fully discrete format divides the music signals into 5.1 channels: Front Left (L), Front Right (R), Centre (C), Left Surround (LS), Right Surround (RS) and Subwoofer (SW: 0.1 channel) for recording and playback. The number of channels that are recorded depends on the software. (1 to 5.1 channels) Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
Audio section General ¡Power supply : 12 V DC (11 – 16 V), test voltage 14.4 V, negative ground ¡Current consumption : Less than 10 A (during disc playback) ¡Power Output : 22 W x 4 ch (DIN 45 324, at 4 Ω) ¡Maximum power output : 50 W x 4 ch ¡Compatible speaker impedance : 4Ω ¡Video input signal : Composite video signal, 1.0 Vp-p (75 Ω) ¡Audio input sensitivity : 2 Vrms ¡Video output signal : Composite video signal, 1.
Matsushita Electric Industrial Co., Ltd. Web Site : http://panasonic.
Installation Instructions Einbauanleitung Instructions d’installation Installatiehandleiding Istruzioni per l’installazione Instrucciones de instalación Model: CQ-VD7005N TEXT ¡ For upgrading your system, read this manual carefully before use. This manual should be retained for future reference after read. ¡ Lesen Sie dieses Handbuch sorgfältig durch, bevor Sie ein System-Upgrade vornehmen. Bewahren Sie dieses Handbuch für späteres Nachschlagen auf.
English Safety Information 1 CAUTION: • PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR INSTALLATION OF THE UNIT. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE TO RAIN, SPLASHING, DRIPPING OR MOISTURE.
English Upgrade Options 2 Main Unit Rear Monitor CQ-VD7005N TV Tuner (CY-TUP153N, option) iPod® Hands-Free Kit featuring Bluetooth® technology (CY-BT100N, option) Expansion Module (CY-EM100N, option) CD Changer (CX-DP880N, option) DVD Changer (CX-DH801N, option) Car Navigation System (CN-DV2300N, option) Contents Safety Information................................................2 Upgrade Options ..................................................3 Contents.............................................
English Installation 3 Preparation Caution ¡Please follow the laws and regulations of your province or country for installation of the unit. ¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. ¡We strongly recommend you to wear gloves for installation work to protect yourself from injuries. Dashboard Installation Installation Opening The unit can be installed in any dashboard having an opening as shown below.
No. Item English ❏ Installation Hardware (For Installation) ❏ Installation Hardware (For Wiring) Diagram q Trim Plate Qty. 1 (YFC054C087CA) w Mounting Collar No. Item e Mounting Spring 1 !1 Clip Connector 1 (YAJ024C118ZA) !2 Reverse Extension Cord 2 (YFX054C077CA) r Mounting Bolt (5 mmø) Qty.
English Installation 5 (continued) Mounting the Main Unit ❏ Installation Procedures (When using Mounting Collar w) 1 Note: ¡The car model, installation conditions and combination of the units used may impose some restrictions on opening and closing the monitor as well as on the angle and position to which the monitor can be adjusted. Insert the Mounting Collar w into the dashboard, and bend the mounting tabs out with a screwdriver.
English Method for Fixing the Mounting Spring Two holes of the mounting spring allow you to select between two mounting types as shown below. (A) Regular installation method 6 (B) Deeper installation method A few millimeters of console projecting y Flat-Head Screw Less projecting y Flat-Head Screw y Flat-Head Screw y Flat-Head Screw Caution ¡Method (B) is not available in some types of cars.
English Installation 7 (continued) ❏ Installation Procedures (When not using Mounting Collar w) Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer. Select mounting screws according to the hole positions and hole shape of the bracket.
English Connecting the Side Brake (Parking Brake) Connection Lead 8 Caution ¡For safety, be sure to ask your nearest professional installer to do this connection. Hand brake Foot brake Side brake (parking brake) switch The side brake (parking brake) switch position varies with car model. For details on the exact location of the side brake (parking brake) switch in your car, contact your dealer.
English Electrical Connections 9 ❏ Wiring Diagram Caution ¡Check the connectors provided on your car (see precaution below) before connecting the system. ¡This unit is designed for use in a car having a 12 V negative ground battery system. ¡To prevent damage to the unit, be sure to follow the connection diagram. ¡Strip about 5 mm of the lead ends for connection (only non-ISO connector cords). ¡Do not insert the power connector into the unit until the wiring is completed.
English Side Brake (Parking Brake) Connection Lead (Bright green) Be sure to wire the side brake (parking brake) for safety and preventing accidents. Navi Mute Lead (Orange) To navi mute lead of car navigation system. External Amplifier Control Power Lead (Blue/white stripe) To an external amplifier. Note: ¡Use the power control lead of the TV tuner for TV tuner connection.
English Electrical Connections (continued) Names and Colors of Rear Connectors RGB Connector To the Panasonic Car Navigation System. 11 System-up Connector To external devices equipped with system-up connector. CQ-VD7005N (Rear) !3 ISO Antenna Adapter (If needed) !0 Power Connector (a page 11) (R)(Red) AV-OUT (L)(White) Video Output Terminal (AV-OUT) Connect the rear monitor. (a page 18) (Yellow) PRE-OUT FRONT PRE-OUT CENTER PRE-OUT REAR S.
English Connection with TV Tuner (CY-TUP153N) Note: ¡Refer to the operating instructions for the connected devices, in addition. External Amplifier Control Power Lead Note: ¡Connect both the power control lead of the TV tuner and the amplifier control connector of the external amplifier when the TV tuner and external amplifier are connected at the same time. 12 Clip connector (option) Power Control Lead PWR-CONT !0 Power Connector AMP-CONT MAX 0.
English Electrical Connections (continued) Connection with DVD Changer (CX-DH801N) Note: ¡Refer to the operating instructions for the connected devices, in addition.
English Connection with CD Changer (CX-DP880N) Note: ¡Refer to the operating instructions for the connected devices, in addition.
English Electrical Connections (continued) Connection with Expansion Module (CY-EM100N) Note: ¡Refer to the operating instructions for the connected devices, in addition.
English Connection with Rear View Camera Note: ¡Refer to the operating instructions for the connected devices, in addition.
English Electrical Connections 17 (continued) Connection with Rear Monitor Note: ¡Refer to the operating instructions for the connected devices, in addition. ¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in order to establish a proper connection.
Note: ¡Refer to the operating instructions for the connected devices, in addition.
Matsushita Electric Industrial Co., Ltd. Web Site : http://panasonic.
System Upgrade Guidebook System-Upgrade-Handbuch Guide pratique de mise à niveau de système Systeemuitbreidingsgids Guida per il potenziamento del sistema Guía de mejora del sistema Model: CQ-VD7005N ¡ For upgrading your system, read this manual carefully before use. This manual should be retained for future reference after read. ¡ Lesen Sie dieses Handbuch sorgfältig durch, bevor Sie ein System-Upgrade vornehmen. Bewahren Sie dieses Handbuch für späteres Nachschlagen auf.
English Safety Information 1 ■ Read the operating instructions for the unit and all other components of your car audio system carefully before using the system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual. Warning This pictograph intends to alert you to the presence of important operating instructions and installation instructions.
Observe the following cautions when using this unit. ❑ Keep the sound volume at an appropriate level. Keep the volume level low enough to be aware of road and traffic conditions while driving. ❑ Do not insert or allow your hand or fingers to be caught in the unit. To prevent injury, do not get your hand or fingers caught in moving parts or in the disc slot. Especially watch out for infants. ❑ This unit is designed for use exclusively in automobiles.
English Before Reading These Instructions 3 Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company.
English Connectable devices ■ DVD Changer ■ Hands-Free Phone System The optional adapter (Conversion Cable for DVD/CD Changer: CA-CC30N) allows you to connect the optional Panasonic DVD changer unit (CX-DH801N). For details, refer to the operating instructions for the DVD changer unit. You can connect the optional Hands-Free Phone System (Hands-Free Kit featuring Bluetooth® technology: CY-BT100N). For details, refer to the operating instructions for the Hands-Free Phone System.
English Before Reading These Instructions (continued) 5 System upgrade sample ■ Simultaneous Multi-Device Connection CQ-VD7005N CD Changer (CX-DP880N, option) DVD Changer (CX-DH801N, option) System-up Connector Only 1 unit Conversion Cable for DVD/CD Changer (CA-CC30N, option) iPod Up to 4 units Direct cable for iPod (CA-DC300N, option) Expansion Module (CY-EM100N, option) Note: ¡ Refer to individual instruction and installation manuals for each device for detailed installation and wiring.
English ■ 5.1-channel Surround System This unit has a built-in 4-channel amplifier. The procedure for setting up a 5.1-channel surround system in order to play DVD software in a way that creates a “you are there” feel in a car is described below. 6 Note: ¡Even if you are using this unit without installing a centre speaker, surround speakers, or a subwoofer, it is still necessary to make the speaker settings in order to adjust the sound balance.
English Touch Panel Operation Overview 7 ❒ Notes on the Touch Panel Before operation ¡Clean the surface of the touch panel. (a Operating Instructions) Operation ¡Use only your fingers to operate the touch panel. ¡Do not press the panel forcefully. ¡Do not scratch the panel with fingernails or any hard objects. ¡Do not use a pen or other sharp implements to operate the touch panel. ¡Do not bump the front panel. a Failure to observe the above may damage or break the glass on the surface of the touch panel.
English Switching the display Touching allows users to switch between screens as follows. ❏ How to Call up Operation Screen Source Standard Screen 8 Operation Screen CD Changer (a page 12) iPod (a page 18) ❏ How to Cancel OSD (On Screen Display) Source Standard Screen OSD OFF *2 TV tuner (*1) (a page 10) DVD Changer (*1) (a page 13) *1 To switch Operation Screen ON, touch the centre of touch panel or press [ENTER]. *2 The operation screen is not available in the video mode.
English TV Tuner Control 9 Preparation: ¡Connect a TV tuner (CY-TUP153N, option) to the unit. ¡It is required to install the TV antenna to receive TV broadcasts. TV Mode Selection ¡For receiving TV broadcasts, stop your car where there is no obstacle to broadcast reception around. Source Button q Touch “Source Button”. TILT CLOSE d (TV) w Touch on the Source Selection Screen.
English Preset Memory Operations Auto Preset Memory 12 channels with first to 12th highest in signal strength will be preset to each band. 10 END [BAND] DVD VTR RADIO CH-C [ENTER] Select a band. ¡Touch/press and hold for more than 2 seconds. ¡ “–” appears if the number of receivable channels is less than 12. New channels overwrite existing saved channels. Writing Preset Memory Favorite preset channels can be written after you have set the preset channel once. Select a band and a channel.
English CD Changer Control 11 ¡CD changer functions are designed for optional Panasonic CD changer unit. (CX-DP880N) Preparation: ¡Connect the CD changer, and load a magazine (discs). Source Button Current track CD Changer Mode Selection q Touch “Source Button”. d TILT CLOSE Disc number (CHw Touch C) on the Source Selection Screen.
Preparation: ¡Connect the DVD changer, and load a magazine (discs). ¡DVD changer functions are designed for optional Panasonic DVD changer unit. (CX-DH801N) DVD Changer Mode Selection English DVD Changer Control 12 q Touch “Source Button”. d Source Button (CHw Touch C) on the Source Selection Screen. (Content varies with connected devices) TILT CLOSE Operation Buttons Press [SRC] to change to the DVD Changer mode.
English DVD Changer Control (continued) Basic Operations (continued) Slow Playback [d] DVD VCD [d] 13 ¡Touch/press and hold in the pause mode. Playback is at about 1/4 normal speed. To resume normal playback, touch/press / [5]. Note: ¡Reverse slow playback is not possible. Disc Selection DVD VCD – – Next disc CD – – Previous disc MP3 …… Touch/Press and hold Chapter/title/track Selection Showing menu and selecting an item * Note on VCD: For VCD, press [RETURN] instead of [DVD MENU] .
Preparation: ¡Connect the Car Navigation System. ¡Specify the correct terminal that is connected to the car navigation system in the NAVI INPUT . (a page 20) ¡If CN-DV2300N is connected, adjust the display position of CN-DV2300N. (a Refer to the method on page 31 in the Instruction Manual for CN-DV2300N.) Car Navigation Mode Selection TILT English Car Navigation System 14 CLOSE Press [NAVI] to change to the car navigation mode. Press [NAVI] again to cancel.
English Bluetooth Hands-Free Kit 15 Preparation: ¡Connect the Bluetooth hands-free kit (CY-BT100N) and establish the pairing. Refer to the instruction manual for the Bluetooth hands-free kit for further information. Connection of the optional Bluetooth hands-free kit allows users to talk on a handsfree cellular phone in a car. Note: ¡CY-BT100N is designed only for receiving calls. It cannot send calls.
English Useful Function Operations Adjustment of Ring Volume 16 Adjust the volume when a call is comming in. END – When the ringtone is the same as that of the cellular phone, DVD VTR RADIO CH-C down [–] [VOL] – [+] up [VOL] When the ringtone is not the same as that of the cellular phone (but this unit-specific sound), Adjust the volume when a call is comming in.
English iPod Control 17 Preparation: ¡Connect the iPod through connecting cable (CA-DC300N, option). iPod Mode Selection Source Button q Touch “Source Button”. Information of current track/file TILT CLOSE d w Touch (iPod) on the Source Selection Screen. (Content varies with connected devices) text/title scroll operation buttons OPEN / CLOSE ASPECT ASP CQ-VD7005N TILT O/C TEXT P·MODE Press [SRC] to change to the iPod mode. CQ-VD7001U VOL ENTER MUTE To switch Operation Screen ON, touch .
– – To cancel, touch again. English – – To cancel, touch and hold again. 18 Useful Function Shuffle Songs * Shuffle Albums * Note: ¡The shuffle function of iPod corresponds to the RANDOM function of this unit. Repeat Play – To cancel, touch again. – Note: ¡The All Repeat Play function of iPod is always activated and cannot be canceled from this unit. …… Touch/Press and hold Touching * Touch panel symbols will change to indicate these current mode.
English Settings 19 This is a guide book specific to system upgrading. Please refer to the operating instructions for basic operations, menu operations, specifications, etc.
English Note: OUTPUT SELECT 20 Output Selection REAR MONITOR (Rear Monitor Set up) You can have different picture and sound on the front and rear monitors at the same time. Preparation: Connect another optional rear monitor. (a Installation Instruction) ❑ When the Expansion Module (CY-EM100N, option) is disconnected: AUTO : same as front monitor* DVD : DVD/VCD/CD/MP3/WMA AV1 : AV1 AV2 : AV2 ¡The screen above shows the case that no device is connected to the Expansion Module.
English Troubleshooting ❑ If You Suspect Something Wrong Check and take steps as described below. 21 If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Service Centre. The product should be serviced only by qualified personnel. Please refer checking and repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking.
English ❑ Error Display Messages ■ CD Changer/DVD Changer Control Display NON PLAYABLE DISC MECHANISM ERROR Possible cause a Possible solution Disc has scratches. aCheck disc. No operation by some cause. aPress [u]. If failure persists, press the reset switch. (Press the reset switch in the CD changer). If normal operation is not restored, call the store where you purchased the unit or the nearest Panasonic Service Centre. FILE ERROR The type of the file that is selected is not supported.
Matsushita Electric Industrial Co., Ltd. Web Site : http://panasonic.
