Operating Instructions High-Power Cassette Player/Receiver with Changer Control CQ-R221W R • Please read these instructions carefully before using this product and save this manual for future use.
Contents E N G L I S H Page Precautions ................................................... 2 Power and Sound Controls ........................... 4 Radio Basics ................................................. 6 Casssette Tape Player Basics ...................... 8 CD Changer Basics .................................... 11 Clock Basics ............................................... 13 Remote Control Unit Preparation................. 14 Installation Guide .........................................
.................................................. 3 ..................................... 24 ..................................... 26 ....................... 28 ................... 31 ..................................... 33 ............................................. 34 ....................................................... 35 ................................................ 38 ................................................ 40 ............................................ 41 .........................
Power and Sound Controls E N G L I S H 1 CQ-R221W S•HDB Power Turn the key in the ignition until the accessory indicator lights. Press [PWR] to switch on the power. Volume ● Press [VOLj j] or [VOLi i] to increase or decrease volume. Volume Level S•HDB ● CQ-R221W 0 to 39 Press [VOLj j] or [VOLi i] for more than 0.5 second to change numeric levels on the display rapidly. Mute ● Press [MUTE] to mute the sound completely. “MUTE” blinks while this operation. ● Press [MUTE] again to cancel.
E N G L I S H Changing Audio Modes S•HDB Press [SEL] to switch the audio modes as follows. BAS TRE VOL a a (Volume) (Bass) (Treble) c d FAd BAL b (Fader) (Balance) 2 Bass and Treble Press [SEL] to select the BASS/TREBLE mode. Press [VOLj j] or [VOLi i] to increase or decrease the bass/treble response. S•HDB –12 to 0 (Center) to 12 –12 to 0 (Center) to 12 d Balance Press [SEL] to select the BALANCE mode. Press [VOLj j] or [VOLi i] to shift the sound volume to the right or left speakers.
Radio Basics E N G L I S H 3 CQ-R221W S•HDB Change to the tuner mode Press [MODE] to switch the operation mode as follows. TUNER a TAPE CD Changer Control a (When Tape is inserted) (When connecting CD Changer) c d Selecting a Band CQ-R2 Press [BAND] to select the bands as follows. FM1 FM2 FM3 a a c a AM d STEREO indicator lights if the station is broadcasting in stereo. S•HDB Manual Tuning CQ Press [TUNEj j ] or [TUNEi i ] to move to a higher or lower frequency.
E N G L I S H Preset Station Setting Up to 24 stations can be preset in the station memory as follows; FM1 FM2 FM3 4 AM 6 stations 6 stations 6 stations 6 stations Caution: For safety reasons, do not attempt to program while driving. Manual Station Preset CQ-R221 d B Press [BAND] to select a desired band. Use manual or seek tuning to find a station that you want to program into memory. Press and hold one of the station selector buttons [1] through [6] until the display blinks.
Cassette Tape Player Basics E N G L I S H 5 CQ-R221W S•HDB Loading a Cassette Insert the cassette with the exposed tape side facing to the right. Gently push the cassette in until the loading begins. The cassette will be loaded in place and playback starts. CQ-R221W S•HDB Program Indicator (This indication “ ” rotates.) Exposed Tape Side Rewind and Fast Forward Press either [ ] to rewind or [ ] to fast forward the tape.
E N G L I S H Blank Skip Press [5] (SKP) to skip long unrecorded portions on the tape. 6 This is most convenient if you quickly want to skip the remaining unrecorded portions at the end of the tape and fast forward to the beginning of the first music on the reverse side of the tape. To turn it off, press [5] (SKP) again. Notes: ● “B·SKIP” indicator lights. However, the blank skip operation will not work if REPEAT is on. The repeat function has priority over that of the blank skip function.
E N G L I S H Cassette Tape Player Basics (continued) TPS Operation (Tape Program Search) 21W 7 Press [3] (TPS) to activate the tape program search mode. d CQ From the current selection, decide which program you want to select. Now, press [ ] several times forward (up to 9 programs) or press [ ] several times backward (up to 8 ) to select the corresponding program number. (Rewind:) 8 S•HDB or CQ S•HDB 0 c (Fast forward:) 1 9 c EX1.
CD Changer Basics Note: CD changer functions are applicable to units with optional CD changer unit. (sold separately) E N G L I S H 8 CQ-R221W S•HDB To Changer mode While a disc magazine is inserted in the CD changer, press [MODE] to switch to changer mode. Play starts from the first track. Play Time Disc Number Track Number Selecting a Disc CQ-R221W Press [1MTL] (iDISC) or [NR2] (DISCj) to select discs in descending or ascending order.
E N G L I S H CD Changer Basics (continued) Repeating a Track 221W Press [4] (REPEAT) to repeat the current selection. “REPEAT” indicator lights. 9 The current selection continues to repeat until you press [4] (REPEAT) again. Random Selection ● Press [5] (RANDOM) to random selection of music is played from all available CDs. “RANDOM” indicator lights. ● To turn it off, press [5] (RANDOM) again. Scanning Tracks 21W Press [3] (SCAN).
Clock Basics E N G L I S H (The clock system is 12-hours.) 10 CQ-R221W S•HDB Initial Time Setting Press and hold Press and hold [DISP] for more than 2 seconds. “AdJ” is displayed. d Press and hold [DISP] again for more than 2 seconds. “12” blinks indicating the time setting mode is activated. To set hours, press [j j] or [i i]. CQ S•HDB Press again [DISP] for minute setting. To set minutes, press [j j] or [i i]. Hold [j j] or [i i] to change numbers rapidly.
E N G L I S H 11 Remote Control Unit Preparation Battery Installation Remove the battery holder. Take hold of the holder at position B and pull it out by pushing position A in the direction shown by the arrow. (Back side) Lithium battery Install the battery on the battery holder. Set a new battery properly with its (+) side facing up as shown in the figure. Position B Insert the battery holder. Push in the battery holder back into its original position.
Installation Guide Preparation Before installation, check the radio operation with antenna and speakers. Disconnect the cable from the negative (–) battery terminal (see caution below). ● Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°.
E N G L I S H 13 Installation Guide (continued) Installation Procedures Note: Disconnect the cable from the negative (–) battery terminal. 1. Secure the Mounting Collar . Insert Mounting Collar into the car’s dashboard, and bend mounting Dashboard tabs out with a screwdriver. Mounting Tab Mounting Collar 2. Secure the rear of the unit. Screwdriver a) Check the electrical connection by referring to this operating instructions. b) Connect the Mounting Bolt using a suitable wrench.
E N G L I S H To Remove the Unit a) Remove the trim plate with a screwdriver as shown in the figure (Fig. 1). 14 Trim Plate Screwdriver CQ-R2 21W S•HDB Fig. 1 b) Pull out the unit while pushing the two lock levers using Dismounting Plate (Fig 2, 3) c) Remove the unit pulling with both hands. (Fig 4). as follows. Lock Lever CQ-R2 21W S•HDB a 221W CQ-RG S•HDB Fig. 2 Dismounting Plate Fig. 3 Fig. 4 CQ-R2 21W a S•HDB Note: Do not lose the Dismounting Plate.
E N G L I S H Anti-Theft System 15 To Remove the Removable Face Plate This unit is equipped with a removable face plate. By removing this face plate, the radio becomes totally inoperable. The security indicator will blink. a) Switch off the power. b) Press the release button ( ) (Fig. 5). The removable face plate will be released. Press 21W CQ-R2 Fig. 5 c) Remove the removable face plate by pulling on the right side of the unit. Place the removable face plate in a supplied case.
E N G L I S H To install the Removable Face Plate a) Slide the left side of the removable face plate in place. b) Press the right end of removable face plate until “click” is heard. Plastic Tab 16 1W CQ-R22 Removable Face Plate S•HDB CQ-R22 1W S•HDB Fig. 8 Fig. 9 Cutout Cautions: 1. Before removing the removable face plate, make sure the power is off. 2. This removable face plate is not water-proof. Do not expose it to water or excessive moisture. 3.
E N G L I S H 17 Electrical Connection This unit can be connected to an optional CD changer (CX-DP88N). For details consult your nearest Panasonic Service center. ● For connection to a CD changer, refer to the operating instructions of the CD Changer (CXDP88N). ● Caution: ● To prevent damage to the unit, be sure to follow the connection diagram below. ● Remove the covering of the leads about 5 mm long from their end before connecting.
Speaker Connections Cautions: 1. Use ungrounded speakers only. 2. The speakers to be used with this unit should be able to handle more than 40 W of audio power. If an optional amplifier is used, the speakers should be able to handle the maximum output power of the amplifier. Use of speakers with small input ratings can cause damage to the speakers. 3. The speaker impedance should be 4 - 8 ohms.
E N G L I S H 19 Troubleshooting ❏ Troubleshooting Tips PROBLEM Unit will not turn on. Radio has static. POSSIBLE CAUSE PROBABLE SOLUTION Dead vehicle battery. Ignition not on. Charge vehicle battery. Turn ignition to On or Accessory. Bad power line connection. Fuse burned out. Check connections. Replace fuse. Antenna not hooked up. Hook up antenna. Close to high power lines. Move away from high power lines.
Fuse Be sure to use a fuse of the specified rating (12 A) when replacing a blown fuse. Fuses with higher capacity ratings, use of any substitute, or connection without a fuse may result in a fire hazard or damage to the unit. If the replacement fuse fails, consult your nearest authorized Panasonic Service Center. E N G L I S H 20 Maintenance To clean the exterior of this unit, use a soft cloth to wipe the surface. Do not use benzine, thinner or any other type of solvents.
CQ-R221W S•HDB 1 [PWR] ● [VOLj j] [VOLi i] ● [VOLj j] 0 39 [VOLi i] ● [MUTE] S•HDB CQ-R221W MUTE ● S•HDB ● [MUTE] CQ-R221W ● S•HDB [MUTE](S•HDB) [MUTE](S•HDB)2 ● [PWR] 24 CQ-R221W 2
[SEL] VOL BAS TRE S•HDB FAd BAL 2 [VOLj j] [SEL] [VOLi i] S•HDB –12 d 0 12 [SEL] [VOLj j] [VOLi i] –12 0 12 BALANCE S•HDB R R: ● [ 5 L 1 15 , L: [SEL] [VOLj j] [VOLi i] F R , R: 1 F: BAS/ VOL TRE/ 2 BAL/ FADER 15 FAd] [SEL] 25 CQ-R221W
CQ-R221W S•HDB 3 [MODE] a a c d CQ-R22 [BAND] FM1 c S•HDB a FM2 a ST CQ [TUNEj j] [TUNEi i] S•HDB CQ S•HDB 26 CQ-R221W [TUNEj j] [TUNEi i] FM3 a AM d
24 FM1 6 FM2 FM3 6 6 CQ-R221 d AM 6 4 BAND B FM1 [1] AM [6] CQ S•HDB d 21W [1] [6] CQ-R22 [BAND] APM 2 ● [1] [6] 6 S•HDB 21W 5 ● ● MONO [MONO] [MONO] 27 CQ-R221W
CQ-R221W S•HDB 5 CQ-R221W •HDB [ ] [ ] S•HDB [ ] [ ] CQ-R221W B [u] ● [u] [u] ● 28 CQ-R221W
[5] SKP [5] ● SKP B.
( TPS 21W [3] ) ( TPS d [ ] 9 [ ] 8 7 CQ 8 0 c 1 c EX1. [3] [ ] EX2. [3] [ ] EX3. [3] [ ] TPS EX4. [3] [ ] TPS S•HDB 9 TPS or TPS CQ S•HDB [3] TPS TPS 4 ● ● Pencil Do not touch or pull out the tape.
( CQ-R221W S•HDB 8 [MODE] CQ-R221W [1MTL] (iDISC) [NR2] (DISCj) S•HDB CQ [TRACK ] [TRACK ] S•HDB CQ [TRACK ] [TRACK ]0.
( ) 221W [4] REPEAT REPEAT [4] REPEAT 1 [5] RANDOM CD [5] RANDOM 1W [3] SCAN 10 [3] SCAN 1W [3] SCAN 2 10 [3] SCAN 2 ❏ CD Panasonic CD 32 CQ-R221W
12 CQ-R221W S•HDB 10 [DISP] AdJ [DISP] 2 2 12 d CQ S•HDB d [j j] [i i] [j j] [i i] [DISP] [j j] [i i] [DISP] [DISP] 2 [DISP] [DISP] 33 CQ-R221W
A B (+) B 11 A ● Panasonic CR-2025 ● ● ● ● (ATT) PWR PWR SOURCE MUTE MUTE MODE VOL Band/Disc up, program, STOP PRG ji BAND/DISC UP TUNE TRACK TUNE/TRACK, Rewind/ Fast Forward Car Audio 34 CQ-R221W
● (−) ● 30 ● 12 53 mm 1 182 mm 4.5 mm - 6 mm 1 Panasonic 1. 2. 3. 4. 5. 6. 7.
( ) (–) 1. 13 2. a) b) c) d) e) ■ ■ 3 mmφ 36 (−) 3.
a) 1 CQ-R2 21W S•HDB 1 14 b) c) 2, 3 4 CQ-R2 21W S•HDB 221W CQ-RG a S•HDB 2 3 4 CQ-R2 21W a S•HDB 37 CQ-R221W
a) b) ( ) 5 21W CQ-R2 15 5 c) 6 21W CQ-R2 d) 7 7 38 CQ-R221W
a) b) 1W CQ-R22 CQ-R22 1W S•HDB S•HDB 8 16 9 1. 2. 3. 4. 5. 6.
(CX-DP88N) ● Panasonic (CX-DP88N) ● DP88N).
1. 2. 40 W 3. 4 8 4. BTCL 5. 6.
❏ ON ACC 19 2 [ ] [ ] [ ] [ ] CD CD [MODE] CD CD CD CD CD CD CD 42 CQ-R221W CD CD CD
(12 A) Panasonic 20 DC 12 V (11 V - 16 V 14.4 V ; 100 Hz 12 dB ; 10 kHz 12 dB 2.5 A ( 0.5 W 4 ) 40 W 4 (4 ) 20 W 4 (4 DIN45 324 4 2.0 V ( 1 kHz 0 dB) 4 (4 - 8 ) 178 ( ) 50 ( ) 150 ( ) mm 1.6 87.5 - 108 MHz 6 dB/ V S/N 30 dB 35 dB 1 kHz 531 - 1602 kHz 28 dB/ V (S/N 20 dB) 4 2 4.76 cm/sec 110 (C-60) 30 - 14000 Hz ( ) ) 30 - 17000 Hz ( 0.
MEMO
MEMO
MEMO
Matsushita Electric Industrial Co., Ltd. Central P.O.
