Panasonic a Section 300 Installation (Applies to CPC-AII/B Version 9.2 and CPC-EX Version 2.3) Version 2.3/9.
Warning: This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians.
Table of Contents Purpose ...................................................................................................................................... xi Related Documents ................................................................................................................... xi Chapter 1 Requirements .......................................... 1-1 Model Numbers ......................................................................................................................
Contents Section 300-Installation Chapter 4 Trunks and Lines .................................... 4-1 Trunks ..................................................................................................................................... 4-3 Trunk Connectors ................................................................................................................... 4-3 Trunk Connector Pinouts ......................................................................................................
Section 300-Installation Contents Installation ............................................................................................................................ 5-28 Door Box Adaptor (Extension Port) ..................................................................................... 5-31 Single Line Telephone Adaptor ............................................................................................ 5-34 Chapter 6 Double-Cabinet Systems ....................... 6-1 Guidelines .......
Contents Section 300-Installation EM/24 - Key Arrangement .................................................................................................. A-17 Additional Serial Port on CPC Card .................................................................................... A-19 Appendix B: CPC-AII/B 8.0 Updates ........................ B-1 Contents ..................................................................................................................................
Section 300-Installation List of Figures List of Figures Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 3-1. Figure 3-2. Figure 3-3. Figure 3-4. Figure 3-5. Figure 3-6. Figure 3-7. Figure 3-8. Figure 3-9. Figure 3-10. Figure 3-11. Figure 3-12. Figure 3-13. Figure 3-14. Figure 3-15. Figure 3-16. Figure 3-17. Figure 3-18. Figure 4-1. Figure 4-2. Figure 4-3. Figure 4-4. Figure 4-5. Figure 4-6. Figure 4-7. Figure 4-8. Figure 4-9. Figure 4-10. Figure 4-11. Figure 4-12. Figure 4-13. Figure 4-14.
List of Figures Figure 5-2. Figure 5-3. Figure 5-4. Figure 5-5. Figure 5-6. Figure 5-7. Figure 5-8. Figure 5-9. Figure 5-10. Figure 5-11. Figure 5-12. Figure 5-13. Figure 5-14. Figure 5-15. Figure 5-16. Figure 5-17. Figure 5-18. Figure 5-19. Figure 5-20. Figure 5-21. Figure 6-1. Figure 6-2. Figure 6-3. Figure 6-4. Figure 6-5. Figure 6-6. Figure 6-7. Figure 6-8. Figure 6-9. viii Section 300-Programming SMDR Format for CPC-AII and CPC-B Version 3.1 or higher ..................... 5-5 RAI connection ......
Section 300-Installation List of Tables List of Tables Table 1-1. Table 1-2. Table 1-3. Table 2-1. Table 2-2. Table 2-3. Table 2-4. Table 3-1. Table 4-1. Table 4-2. Table 4-3. Table 4-4. Table 4-5. Table 4-6. Table 4-7. Table 4-8. Table 4-9. Table 4-10. Table 4-11. Table 4-12. Table 4-13. Table 4-14. Table 4-15. Table 4-16. Table 4-17. Table 4-18. Table 4-19. Table 4-20. Table 4-21. Table 4-22. Table 5-1. Table 5-2. Table 5-3. Table 5-4. Table 5-5. Table 5-6. DBS model numbers ...........................
List of Tables Table 5-7. Table 5-8. Table 5-9. Table 6-1. Table 7-1. Table 7-2. Table 7-3. Table 7-4. Table 7-5. Table 7-6. Table 7-7. Table 7-8. Table 7-9. Table 7-10. Table 7-11. Table 7-12. Table 7-13. Table 7-14. Table 7-15. Table 7-16. Table 7-17. Table 7-18. x Section 300-Installation Switch settings for wait timing between dialed digits, VAU ....................... 5-23 Switch settings for abbreviated dialing digit length, VAU ...........................
Section 300-Installation About This Manual About This Manual Purpose This manual provides installation instructions for the Digital Business System (DBS). The following table summarizes the purpose of each chapter. Chapter No. Title Purpose 1 Requirements 2 System Overview 3 Cabinet Installation 4 Trunks and Lines 5 Peripheral Equipment 6 Double-Cabinet Systems Specifications Includes DBS model numbers and FCC information that may be required during installation.
About This Manual xii Section 300-Installation DBS Manual - Revised April 2000 DBS-2.3/9.
Chapter 1. Requirements This chapter includes DBS model numbers and FCC information that may be required during installation. In addition, environmental requirements for proper operation are included. This chapter covers the following topics: Topic FCC Requirements Environmental Requirements Cleaning Page 1-1 1-1 1-4 1-5 Model Numbers Table 1-1.
Section 300-Installation Chapter 1. Requirements Table 1-2. FCC information Item Specification FCC Registration Number When used as a key system: ACK4A4-60490-KF-E When used as a PBX: ACK4A4-60489-MF-E 0.5B * E Ringer Equivalence Network Address Signaling Code * The ringer equivalence number (REN) is useful to determine the quantity of devices that you may connect to your telephone line and still have all of those devices ring when your number is called.
Chapter 1. Requirements Section 300-Installation warranty. However, the customer may replace fuses, and plug-in cards, as needed. • The Telephone Company may make changes in its facilities, equipment, operations or procedures, that could affect the proper operation of your equipment. If they do, you will be given advance notice so as to give you an opportunity to maintain uninterrupted service. • The Digital Key Telephones designed for use with this system are hearing aid compatible.
Section 300-Installation Chapter 1. Requirements - Answered by the attendant - Routed to a recorded announcement that can be administered by the CPE user - Routed to a dial prompt. B. This equipment provides answer supervision on all DID calls forwarded to the PSTN. Permissible exceptions are: - A call is unanswered - A busy tone is received - a reorder tone is received T1 Requirements This device must only be connected to the T1 network connected behind an FCC Part 68 registered channel service unit.
Chapter 1. Requirements Section 300-Installation under overhead plumbing, sprinkler system valves, or in areas that are susceptible to flooding. Lighting: Sufficient lighting is required for testing and maintenance. Lightning Protection/Grounding: The system must be properly grounded to protect from lightning damage. The following UL conditions must be met to ensure proper grounding. (For grounding instructions, see page 3-5.
Chapter 1. Requirements 1-6 Section 300-Installation DBS Manual - Revised April 2000 DBS-2.3/9.
Chapter 2. System Overview This chapter gives an overview of the Digital Business System (DBS). This overview includes descriptions of the DBS cabinet, system configurations, printed circuit cards, and the call processor. This chapter covers the following topics:: Topic Cabinet Description Configurations Printed Circuit Cards Processor Description DBS-2.3/9.
2-2 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 2. System Overview Cabinet Description Panasonic’s Digital Business System (DBS) is a hybrid telephone system that can be used as a key service unit (KSU) or a private branch exchange (PBX). The DBS cabinet includes an AC power supply, backup batteries (optional), dedicated card slots, and a central connector panel for line and trunk connections. Figure 2-1.
Chapter 2. System Overview Section 300-Installation Figure 2-2.
Section 300-Installation Chapter 2. System Overview Configurations The DBS comes in three models, which provide from 40 to 96 ports. Up to two systems can be combined to increase port capacity up to 192 ports (DBS 96 + DBS 96). In addition to dedicated trunk and extension slots, each system includes one expansion slot (labeled EC/TRK) that can be used for either trunks or extensions. The following table shows port capacities for individual systems and for different combinations of systems. Table 2-1.
Chapter 2. System Overview Section 300-Installation Printed Circuit Cards The following table describes the printed circuit cards and other equipment that can be used with the DBS. Also included are brief descriptions of each card and the maximum number that can be installed in each cabinet. Table 2-2. Printed circuit card descriptions and maximums Part No.
Section 300-Installation Part No. VB-43706 VB-43707 VB-43551 Chapter 2.
Chapter 2. System Overview Section 300-Installation Printed circuit cards are installed in dedicated slots in the DBS cabinet. Table 2-3 shows the cards that can be installed in each slot. Figure 2-3 on page 2-9 illustrates slot labels. Table 2-3.
Section 300-Installation Chapter 2. System Overview Figure 2-3. Slot labels for printed circuit packages Slot Labels (D BS 96) TRK1 TRK2 TRK3 EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/TRK SCC CPC AUX1 AUX2 Processor Description DBS call-processing is controlled by the Call Processor Card (CPC). Four CPC models are available: CPC-A, CPC-B, CPC-AII, and CPC-EX.
Chapter 2. System Overview 2-10 Section 300-Installation DBS Manual - Revised April 2000 DBS-2.3/9.
Chapter 3. Cabinet Installation This chapter explains how to install and power up the cabinet. Before you begin installation, be sure to read the “Requirements” chapter, which begins on page 1-1. This chapter covers the following topics:: Topic Wall-Mounting the Cabinet Grounding Card Installation Battery Backup Key Phone Wall Mounting DSLT Wall Mounting System Initialization Test Phone DBS-2.3/9.
3-2 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 3. Cabinet Installation Wall-Mounting the Cabinet Guidelines Caution: Always turn the power switch OFF before beginning installation. • The DBS is shipped with the cover installed to protect components. Before wall-mounting the cabinet, remove the cover. • Handle the cabinet carefully to avoid damage. Installation 1. Remove the eight screws from the front and sides of the cabinet. 2. Take the front cover off by pulling it from the bottom and lifting it up. 3.
Chapter 3. Cabinet Installation Section 300-Installation 4. Attach the mounting brackets to the four corners of the back side of the cabinet. Figure 3-2. Cabinet mounting bracket M etal M ounting Bracket 5. Install four screws in the wall studs according to the dimensions given in Figure 3-3. (Note that the width dimension is different for the DBS 40.) The screws are used to attach the mounting brackets to the wall. The screws should protrude from the wall 5/16 in. Figure 3-3.
Section 300-Installation Chapter 3. Cabinet Installation Grounding Guidelines • Before grounding the DBS, read the “Lightning Protection/Grounding” requirements beginning on page 1-6. • The ground cable must be at least 18 AWG. • Resistance to ground must be 10 Ohms or less. Installation 1. Attach the ground cable to the ground screw on the front of the power supply. 2. Connect the ground cable to the building ground. Figure 3-4.
Chapter 3. Cabinet Installation Section 300-Installation Card Installation Guidelines Caution: Before handling printed circuit cards, discharge static electricity by grounding yourself. Static electricity can damage components. Turn off the power before installiing. Installing cards with the power on can damage components. • Install the cards in the following order: - TRK - DEC - AEC or API - SCC - CPC - MFR or CBL • If you are installing a CPC-A or CPC-AII card with an SCC-B card, set SW4 to “Mode A.
Section 300-Installation Chapter 3. Cabinet Installation • Before installing the CPC card, determine if the DBS will be used as a KSU or PBX. To use it as a PBX, cut Strap S1 on the CPC. Cutting this strap allows use of pooled trunks as opposed to line appearances. Figure 3-6. CPC Strap S1 C utS1 forPooled Trunks (PBX O peration) D o N otC utS1 forLine Appearances (KSU O peration) S1 C PC -AIIor C PC -B • Install cards only in their dedicated slots.
Chapter 3. Cabinet Installation Section 300-Installation Installation 1. With the lettering on the card pointed up, position the card within the slot guides. (See Figure 3-7.) 2. Hold the card on the top and bottom edges with both hands and carefully push the card into the slot. 3. When the connector at the far end of the card touches the corresponding connector on the backplane, press the card in until it is firmly seated. Figure 3-7.
Section 300-Installation Chapter 3. Cabinet Installation Battery Backup Guidelines • The DBS 40 uses two 12-volt batteries; the DBS 72 and 96 use four 6-volt batteries or two 12-volt batteries. The following table includes the part numbers for the battery packages. Table 3-1. Battery backup packages for the DBS 40, 72, and 96 System Battery Backup Part No.
Chapter 3. Cabinet Installation Section 300-Installation Installation for the DBS 40 1. Place one battery in the top tray of the battery compartment, the other battery in the bottom tray. Figure 3-8. Battery location, DBS 40 C N 11 CN3 CN2 CN5 CN4 C N 12 CN1 TR K1 EC 1 CN6 C N 15 CN1 EC 2 EC 3 EC /TR K SC C C PC AU X1 AU X2 Batteries 2. Connect the positive cable (red) to the + terminal of the top battery. 3. Connect the connecting cable (white) to the - terminal of the top battery. 4.
Section 300-Installation Chapter 3. Cabinet Installation Installation for the DBS 72 and 96 1. Slide the battery compartment out and place the batteries inside the tray. Figure 3-9. Battery tray, DBS 72 and 96 Rem ove Screw s and Slide Battery Tray O ut 2. Connect the positive cable (red) to the + terminal on the first battery. 3. Connect the negative cable (blue) to the - terminal on the last battery. 4.
Chapter 3. Cabinet Installation Section 300-Installation Figure 3-10.
Section 300-Installation Chapter 3. Cabinet Installation Key Phone Wall Mounting DBS key phones can be modified for wall mounting by reversing the wallmount adaptor on the bottom of the phone. The wall-mount adaptor includes a small hole for attaching the phone to a screw inserted in the wall. 1. Place the bottom edge of the telephone on a desk or other hard surface. 2. Press the wall-mount adaptor down until it detaches from the phone (Figure 3-11). Figure 3-11.
Chapter 3. Cabinet Installation Section 300-Installation 3. Turn the wall-mount adaptor around and re-attach it to the phone. Figure 3-12. Wall-mount adaptor replacement W all-M ount Adaptor 4. Remove the handset guide with a small screwdriver, turn it over, and reinsert it into the phone. Figure 3-13. Handset guide insertion for wall-mounting, key phone 3-14 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 3. Cabinet Installation DSLT Wall Mounting Digital Single-Line Telephones (DSLTs) can be modified for wall mounting by removing the desk stand and mounting it on the bottom of the phone. The back of the DSLT and the desk stand include slots for attaching the phone to a screw inserted in the wall. 1. Press the stand releases in toward the middle of the phone to release the desk stand (Figure 3-14). Figure 3-14.
Chapter 3. Cabinet Installation Section 300-Installation 2. Attach the desk stand to the bottom of the phone by aligning the tabs and tab guides and sliding it into place (Figure 3-15). Figure 3-15. Desk stand attachment for DSLT wall mounting Tabs Tab G uides 3. Remove the handset guide with a small screwdriver, turn it over, and reinsert it into the phone. Figure 3-16. Handset guide insertion for wall-mounting, DSLT 3-16 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 3. Cabinet Installation System Initialization 1. Confirm that the DBS power switch is OFF. 2. Plug the power cord into a dedicated 120V 15 amp AC wall outlet. Note: A surge protector should be installed on the power cord. 3. Set SW1 on the CPC card to RAMCLR (RAM Clear). Figure 3-17. CPC memory clear switch TRK1 TRK2 TRK3 EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/TRK SCC CPC AUX1 AUX2 STATU S LED SW 1 RAM H O LD RAM C LR 4. Turn the power switch on.
Chapter 3. Cabinet Installation Section 300-Installation Test Phone Guidelines • The test terminal (CN3) on the DBS Connector Panel can be used to connect a display phone for programming. The test terminal can be used for initial programming before extension cabling is completed. • The test terminal is turned on by flipping SW1 on the Connector Panel to the “Test” position. When SW1 is in the test position, extension ports 7 and 8 are connected through the test terminal.
Section 300-Installation Chapter 3. Cabinet Installation Figure 3-18. Test telephone connection TestPhone D SS C onsole Panasonic Panasonic 7 8 9 10 11 12 1 2 3 4 5 6 1 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7PRS 8 TUV 9 WXY 0OPER # N ote:Port7 m ustbe assigned as extension 101 and the D SS/72 assigned as telephone type 13 forthe D SS/72 to operate.
Chapter 3. Cabinet Installation 3-20 Section 300-Installation DBS Manual - Revised April 2000 DBS-2.3/9.
Chapter 4. Trunks and Lines This chapter describes trunk and line installation. Some peripheral equipment also requires trunk and/or line interfaces (for example, door phones or power failure units). See Chapter 5 for instructions on connecting peripheral equipment through trunks or lines. This chapter covers the following topics:: DBS-2.3/9.
4-2 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 4. Trunks and Lines Trunks Trunk Connectors Each DBS cabinet is provided with one main trunk connector, labeled CN1. In addition, a trunk expansion connector (VB-43120) can be added to the DBS to provide eight additional trunk connections. (The trunk expansion connector is also labeled CN1.) Figure 4-1 shows the maximum number of trunks that can be connected when both trunk connectors are used with a DBS 96. Figure 4-1.
Chapter 4. Trunks and Lines Section 300-Installation The number of trunks that can be connected through the main trunk connector depends on the type of system you have and the number of trunk cards installed. Table 4-1 shows the main trunks and expansion trunks available with each system type. Chapter 6 includes trunk maximums for two-cabinet systems. Table 4-1.
Section 300-Installation Chapter 4. Trunks and Lines Table 4-2. Pinouts and trunk numbers for the main trunk connector.
Chapter 4. Trunks and Lines Section 300-Installation Table 4-3. Pinouts and trunk numbers for trunk expansion connector CN1 Trunk Slot Color Code EC/TRK WH-BL BL-WH WH-OR OR-WH WH-GN GN-WH WH-BR BR-WH WH-SL SL-WH RD-BL BL-RD RD-OR OR-RD RD-GN GN-RD Pin No.1 Desig.
Section 300-Installation Chapter 4. Trunks and Lines Loop-Start Trunks Guidelines • Two versions of the loop-start trunk are available: the four-port version (VB-43510) and the eight-port version (VB-43511). • The following procedure covers loop-start trunk installation using the main trunk connector. For instructions on using the expansion trunk connector, see “Trunk and Line Expansion” on page 4-44 • For pinouts and color codes for the main trunk connector, see Table 4-2 on page 4-5.
Chapter 4. Trunks and Lines Section 300-Installation 2. Install the loop-start trunk in a trunk slot. 3. Use a standard 50-pin cable to connect the trunks from the MDF to the main trunk connector CN1. Installation with Caller ID 1. Remove the cover from the L-TRK card (VB-43511A). This cover should be set aside since it cannot be reinstalled with a Caller ID Board installed. 2. Cut strap J1 on the L-TRK card as shown in Figure 4-2. 3. Set switches SW1 through SW8 on the L-TRK card (VB-43511A) to OFF.
Section 300-Installation Chapter 4. Trunks and Lines Ground Start and DID Trunks Guidelines • The following procedure covers ground-start (VB-43531) and DID (VB43541) installation using the main trunk connector. For instructions on using the expansion trunk connector, see “Trunk and Line Expansion” on page 4-44. • For pinouts and color codes for the main trunk connector, see Table 4-2 on page 4-5. • Each circuit on the ground-start trunk card can be used as either a loopstart or ground-start trunk.
Chapter 4. Trunks and Lines Section 300-Installation Installation 1. Install the G-TRK/8 or DID card in a trunk slot. 2. Connect the power supply by cabling the positive side to the SG connector on CN2 (Figure 4-4). Note: Use cables that are 18 AWG or larger to connect the power supply to the DBS. Figure 4-4.
Section 300-Installation Chapter 4. Trunks and Lines Connect the test set across the tip and ring of the trunk to be tested. With the test set in the “monitor” position, apply ground to the ring side of the trunk. If you hear dial tone, the polarity of the trunk is okay, and you can switch the test set to the “talk” mode to test the voice path. If you do not hear dial tone, ground the tip side of the trunk. If you receive dial tone when grounding the tip side, polarity is reversed.
Chapter 4. Trunks and Lines Section 300-Installation Table 4-7. T1 Hardware requirements for double-cabinet systems T1 CPC-B V4 SCC-B T1 Trunk T1 MDF Sync T1 Cable Cable Kit Location (VB-43411) (VB43421) Card Card Card (VB-43110) (VB43561) (VB43562) (VB43563) (VB43564) 1 1 1 0 1 (See Note 1.) (See Note 4.) T1 in the 1 (See Notes 2 and 3.) 1 Master T1 in the 1 1 1 1 1 1 1 Slave T1 in both 1 1 2 2 1 1 1 Master and Slave Notes: 1. Version 1.
Section 300-Installation Chapter 4. Trunks and Lines Table 4-8. T1 slot usage for two-cabinet systems System Size EC/TRK Slot Usage for T1 Master Slave DBS 40 + DBS 40 DBS 72 + DBS 40 DBS 72 + DBS 72 DBS 96 + DBS 40 DBS 96 + DBS 72 DBS 96 + DBS 96 No No No Yes Yes Yes Yes No Yes Yes Yes Yes • Fractional T1 can be used when fewer than 24 T1 trunks are needed. Fractional T1 allows you to use only a portion of the 24 channels provided on the T1 card.
Chapter 4. Trunks and Lines Section 300-Installation Trunk Assignments for Single-Cabinet Systems • Programming is not required to associate trunk ports with slot locations. However, you must use programming to specify that a combination of T1 and analog trunks are installed, and you must also specify how many T1 channels are used. Table 4-9.
Section 300-Installation Chapter 4. Trunks and Lines Table 4-11.
Chapter 4. Trunks and Lines Section 300-Installation Tables 4-13 through 4-17 show trunk numbering for two-cabinet systems using the maximum number of T1 channels. Table 4-13. T1 and analog trunk assignments, DBS 40 + 40 (16-channel fractional T1 in the slave) Trunk Number 1 ↓ 8 9 ↓ 16 17 ↓ 24 Master Cabinet Analog trunk 1 ↓ Analog trunk 8 N/A Ν/Α Slave Cabinet N/A T1 channel 16 ↓ T1 channel 9 T1 channel 8 ↓ T1 channel 1 Table 4-14.
Section 300-Installation Chapter 4. Trunks and Lines Table 4-15. T1 and analog trunk assignments, DBS 96 + DBS 40 (24-channel T1 in the master; 16channel T1 in the slave) Trunk Number 1 ↓ 8 9 ↓ 16 17 ↓ 24 25 ↓ 32 33 ↓ 40 41 ↓ 48 DBS-2.3/9.
Chapter 4. Trunks and Lines Section 300-Installation Table 4-16.
Section 300-Installation Chapter 4. Trunks and Lines Table 4-17. T1 and analog trunk assignments, DBS 96 + DBS 96 (24-channel T1 in the master; 24channel T1 in the slave) Trunk Number 1 ↓ 8 9 ↓ 16 17 ↓ 24 25 ↓ 32 33 ↓ 40 41 ↓ 48 49 ↓ 56 57 ↓ 64 DBS-2.3/9.
Chapter 4. Trunks and Lines Section 300-Installation Installation The following procedures provide step-by-step instructions for installing the T1 Interface. The procedure that you should use depends on the type of system you have and the number of T1s you are installing. If you are installing ... Use this procedure...
Section 300-Installation Chapter 4. Trunks and Lines Installing a T1 in a Single Cabinet The following instructions explain how to install a T1 in a single-cabinet system. These instructions also apply when a T1 is installed in only the master cabinet of a two cabinet system. If only one T1 is installed in a two-cabinet system, it must be installed in the cabinet specified in Table 4-8 on page 4-13. Note: The T1 Interface cannot be used for systems consisting of a DBS 72 connected to a DBS 40. 1.
Chapter 4. Trunks and Lines Section 300-Installation 2. Attach the Sync Unit to the CPC-B card. Note: Before attaching the Sync Unit, insert the three spacers provided with the unit and remove the jumpers from CN2 of the CPC-B card. Figure 4-6. T1 Sync Unit installation 4-22 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 4. Trunks and Lines 3. Install the T1 MDF (main distribution frame) card in the top of the cabinet as shown in Figure 4-7. Figure 4-7. T1 MDF card installation DBS-2.3/9.
Chapter 4. Trunks and Lines Section 300-Installation 4. Set SW1 on the T1 card according to the following table. These switch settings correspond to the distance between the DBS and the CSU. To turn a switch on, flip it to the “up” position. Table 4-18. Switch settings for SW1 on the T1 card SW Distance from the DBS to the CSU 0 to 150 ft. 150-450 ft. 450-655 ft.
Section 300-Installation Chapter 4. Trunks and Lines Figure 4-9. RJ48 pinouts, CN1 connector 2 8 Tip1 Ring NC FG 1 7 Ring1 NC Tip FG Tip1 =Receive Ring1 Tip Ring =Transmit CN1 (RJ48) DBS-2.3/9.
Chapter 4. Trunks and Lines Section 300-Installation 9. Connect the ground cable from the T1 MDF card to the cabinet as shown in Figure 4-10. Figure 4-10. T1 cabinet connections, single-cabinet installation T-1 Line C N 11 SW 1 CN3 CN2 CN5 CN4 C N 13 C N 14 CN6 C N 12 C SU CN1 CN1 TRK1 TRK2 TRK3 EC1 CN3 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/TRK SCC T-1 M D F CPC AUX1 AUX2 G round C able Sync U nit CN3 CN1 T-1 C ard CN5 Sync C able 4-26 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 4. Trunks and Lines Installing T1 in a Double Cabinet with the T1 in the Slave 1. Install the Sync Unit in the master cabinet as described in Steps 1 and 2 under “Installation for a Single T1.” 2. Install a T1 MDF card in the slave cabinet. (See Step 3 on page 4-23.) 3. Set Switch 1 on the T1 card. (See Step 4 on page 4-24.) 4. Install a T1 card in the “EC/TRK” slot of the slave cabinet. 5.
Chapter 4. Trunks and Lines Section 300-Installation Figure 4-11.
Section 300-Installation Chapter 4. Trunks and Lines Installing T1 in a Double Cabinet with T1s in the Master and Slave 1. Install the Sync Unit in the master cabinet as described in Steps 1 and 2 under “Installation for a Single T1.” 2. Install a T1 MDF card in each cabinet. (See Step 3 on page 4-23.) 3. Set Switch 1 on the T1 cards. (See Step 4 on page 4-24.) 4. Install a T1 card in each “EC/TRK” slot. 5.
Chapter 4. Trunks and Lines Section 300-Installation Figure 4-12.
Section 300-Installation Chapter 4. Trunks and Lines Lines Extension Connectors The number of extension ports that can be connected to your system depends on the type of system you have. Figure 4-13 shows the maximum number of extensions that can be connected to each system when the extension expansion connector is used. Table 4-1 summarizes the number of ports that can be used without the extension expansion connector. Chapter 6 includes extension maximums for two-cabinet systems. Figure 4-13.
Chapter 4. Trunks and Lines Section 300-Installation Table 4-19. Extension ports provided with each system System Type Extension Ports (Not including the Expansion Connector*) DBS 40 1-24 DBS 72 1-48 DBS 96 1-72 *Note: Extensions 65 to 72 on the DBS 96 use the EC/TRK slot, but they do not require the extension expansion connector. If extensions 65 to 72 are used, the trunk expansion connector cannot be used.
Section 300-Installation Chapter 4. Trunks and Lines Table 4-20.
Chapter 4. Trunks and Lines Section 300-Installation Table 4-21.
Section 300-Installation Chapter 4. Trunks and Lines Table 4-22.
Chapter 4. Trunks and Lines Section 300-Installation Table 4-23. Pinouts and color codes for extension expansion connector CN1 Extension Slot Color Code Pin No.
Section 300-Installation Chapter 4. Trunks and Lines Analog Extensions Note: Normally analog extensions are supported using the AEC (VB-43621). Alternatively, a Single Line Telephone Adaptor (SLTA, VB-43709) may be used to support analog DTMF (2500 set) extensions. The SLTA converts up to 4 digital ports to analog ports. See “Single Line Telephone Adaptor” on page 5-34 for more information. Guidelines • An MFR card (VB-43431) is required when the AEC is used.
Chapter 4. Trunks and Lines Section 300-Installation Figure 4-14. SLT ringer box installation 4-38 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 4.
Chapter 4. Trunks and Lines Section 300-Installation 4. Use a standard 50-pin cable to connect the extensions from the MDF to the appropriate extension connector. (Refer to Tables 4-20 through 4-22 for extension pinouts.) 5. If you are installing a DBS 40 system, attach the EMI filter to the amphenol cable as shown in Figure 4-15. Figure 4-15. EMI filter installation (DBS 40 only) EM I Filter 3 1/2" 4-40 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 4. Trunks and Lines Digital Extensions The following instructions explain how to connect digital extensions. These instructions apply for key phones and Digital Single-Line Telephones (DSLTs). Special instructions are provided for installing the DSS/72 and EM24 terminals, which connect to digital phones. 1. Install the DEC cards in extension slots. 2.
Chapter 4. Trunks and Lines Section 300-Installation Installation 1. Attach the DSS/72 to the key phone using the mounting plate and the four screws. 2. Connect the DSS to the key phone using the two-conductor cable. 3. Connect the DSS to the wall jack using a four-conductor cable. 4. Connect the four wires from the key phone and DSS to the MDF. Figure 4-16. DSS/72 connection using one cable with two pairs. 4-42 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 4. Trunks and Lines EM/24 Guidelines • The EM/24 (VB-43310) provides 24 flexible function (FF) keys. It can be attached to any key phone. • The EM/24 comes with a mounting bracket, screws, and a two-conductor cable for attaching it to a key phone. Installation 1. Attach the EM/24 to the key phone using the mounting plate and the four screws, as shown in Figure 4-17. 2. Connect the EM/24 to the key phone using the two-conductor cable. 3.
Chapter 4. Trunks and Lines Section 300-Installation Trunk and Line Expansion Guidelines • The EC/TRK slot can be used for a trunk or extension card. • Different expansion connectors are used for trunks and extensions: Expansion connector Part No. Trunk expansion connector Extension expansion connector VB-43120 VB-43121 Note: With the DBS 96, the expansion connector is not required to use the EC/TRK slot for an extension card.
Section 300-Installation Chapter 4. Trunks and Lines Figure 4-18. Trunk or extension expansion Screw C N 11 Trunk or Extension Expansion C onnector FG Term inal M otherboard C N 15 C N 15 CN1 CN2 (O n the expansion connector) CN1 G round C able Fasten w ith Screw Front View Right Side View C O Lines or Extensions See Table 4-3 on page 4-6 for pinout and trunk number information for the trunk expansion connector. DBS-2.3/9.
Chapter 5. Peripheral Equipment This chapter describes peripheral equipment installation. Some peripheral equipment requires trunk and/or line interfaces (for example, door phones or power failure units). For information on trunk and line connections, see Chapter 4. This chapter covers the following topics: DBS-2.3/9.
5-2 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 5. Peripheral Equipment Local Terminal or SMDR Device Guidelines • Connector 6 (CN6) on the Connector Panel provides an RS-232C interface for connection of a local programming terminal or an SMDR device such as a printer or call accounting machine. • The following table contains RS-232C designations. Table 5-1. RS-232C pin designations used for CN6 Pin Signal Name Description 1 2 3 4 5 6 7 8 20 N/A TD RD CTS RTS DSR SG CD DTR Not used.
Chapter 5. Peripheral Equipment Section 300-Installation Installation 1. Connect one end of the RS-232C cable to CN6 on the Connector Panel. Figure 5-1 shows cable pinouts for 25-pin and 9-pin RS-232C devices. These connections have been used successfully with many PCs and SMDR devices; however, consult the documentation of the PC or SMDR device before fabricating a cable. 2. Connect the other end of the RS-232C cable to the local programming terminal or SMDR device. Figure 5-1.
Section 300-Installation Chapter 5. Peripheral Equipment Figure 5-2. SMDR Format for CPC-AII and CPC-B Version 3.1 or higher 1 2 3 4 5 6 7 012345678901234567890123456789012345678901234567890123456789012345678901234567 1 2 3 4 5 6 7 8 9 T MM/DD HH:MM:SS HH:MM.SS NNN DDDDDDDDDDDDDDDDDDDDDDDDDDDD AAAAAAAAAA VVVVV NN 1=Call type S=Inbound DISA s=Outbound DISA I=Incoming O=Outgoing T=Transfer (See Note 1.
Chapter 5. Peripheral Equipment Section 300-Installation Remote Administration Interface (RAI) Guidelines • The RAI is a modem card that installs on the SCC card. The card is used to remotely administer the system through a trunk line. • Two versions of the RAI card are available. Both versions use 1 Stop bit, 8 data bits, and no parity. The RAI-A card has a fixed baud rate of 300. The RAI-B card supports both 300 and 1200 baud operation.
Section 300-Installation Chapter 5. Peripheral Equipment Figure 5-3. RAI connection RAI-A(VB-43706): 300 bps or RAI-B(VB-43707): 300 or 1200 bps H ooks SC C -B C ard (VB-43421) RAI-B C ard J1 Leave J1 C losed (300 BPS/1200 BPS M ode) SW 4 O FF ON 1 2 4 7dBm DBS-2.3/9.2-300 8 16 Sets attenuation level. The attenuation is the sum of the "O N " settings.
Chapter 5. Peripheral Equipment Section 300-Installation Background Music/Music-On-Hold Guidelines • A single music source can be used for both background music (BGM) and music-on-hold (MOH), or separate music sources can be used for each feature. • If a single music source is used for both MOH and BGM, the music source connects to CN5 on the Connector Panel. If separate sources are used, the MOH source connects to CN5, and the BGM source connects to the BGM connector on the SCC card.
Section 300-Installation Chapter 5. Peripheral Equipment Note: To change the volume levels of the music sources, adjust the variable resistors on the SCC card. Table 5-3. SCC variable resistors Variable Resistor Purpose SCC-A VR1 VR5 Adjusts CO ringing tone volume. Adjust MOH and BGM volume. SCC-B VR1 VR2 VR6 Adjusts MOH volume. Adjust BGM volume. Adjusts CO ringing tone volume. Figure 5-4.
Chapter 5. Peripheral Equipment Section 300-Installation Off-Premises Adaptor (OPX) Guidelines • Analog phones can be connected as off-premise stations through a direct line to the DBS or through the central office, depending on how far the stations are from the OPX Adaptor. Table 5-4 shows how far the OPX stations can be from the adaptor without going through a CO. Table 5-4. Maximum distances for direct connection to OPX stations Wiring gauge Max.
Section 300-Installation Chapter 5. Peripheral Equipment Installation The following procedures describe direct OPX connection and OPX connection through a CO. Order an OL13C circuit for an OPX through a CO. Refer to Figure 5-6 on page 5-13 when installing the OPX. Installing an OPX Station Without Going Through a Central Office 1. Remove the cover from the OPX Adaptor. 2. Remove the cable punch-out plate (Figure 5-12) to make an opening for the cables coming into the OPX Adaptor.
Chapter 5. Peripheral Equipment Section 300-Installation 4. Connect the “R” and “T” leads to a digital extension port on the DBS. 5. Connect the “GND” lead on the OPX Adaptor to the DBS Frame Ground screw. 6. Connect the “TR” and “TT” leads to the OPX station. 7. Install the cover on the OPX Adaptor. 8. Turn the system off and back on, or unplug the cable connected to the digital extension and then plug it back in. Installing an OPX Station Through a Central Office 1.
Section 300-Installation Chapter 5. Peripheral Equipment Figure 5-6. OPX installation To a D BS digitalline port R 5 CI 4 CI T (Term inals forexternal E-R G + ringing source) E-R G 1J 2J To off-prem ise SLT or dem arcation block To the D BS Fram e G round screw TR TT G ND 1 3 CN3 O ff-Prem ise Extension Adaptor (VB-43702) DBS-2.3/9.
Chapter 5. Peripheral Equipment Section 300-Installation Paging The DBS allows extensions to be grouped into paging groups numbered 0007. When you issue a page (by dialing #00-#07), you specify a paging group, so that your announcement is heard over the key telephones and Digital Single Line Telephones that are members of that group. Paging groups often include people whose work is related. External zone paging allows you to connect up to five speaker groups to the DBS.
Section 300-Installation Chapter 5. Peripheral Equipment 3. Connect the zone relays to the amplifier. 4. Connect the zone relays to the +24V and zone paging terminals (Z0-Z4) on the Connector Panel. Figure 5-7.
Chapter 5. Peripheral Equipment Section 300-Installation External General Page/UNA Installation Use this procedure to connect a general page system, connect UNA over a page system or connect a combined page/UNA system. 1. Connect CN4 on the DBS Connector Panel to the audio input of the paging amplifier. (See Figure 5-8.) 2. Connect the audio output of the amplifier through the C and M relay terminals to the speaker(s) as shown in Figure 5-8. Figure 5-8.
Section 300-Installation Chapter 5. Peripheral Equipment • If UNA operates over the paging system, the Audio Output of CN4 provides the Audio Ringback sound to be heard over the paging system when a trunk rings UNA. • If UNA operates over the paging system, the UNA ringing will always takes precedence over paging. When a page is interrupted in progress, the pager must hang up and wait until after UNA ringing ends to reinstate the page.
Chapter 5. Peripheral Equipment Section 300-Installation Installation 1. Connect the external ringer to the “C” and “M” terminals on the Connector Panel. (See Figure 5-9 on page 5-18.) Note: When the Ring Patterns for UNA Terminals (M, C, & B) programming command (FF1 2# 4# 1# (0 or 1)# is set to 0, connecting the ringer to the “C” and “M” terminals provides a “1 second on/3 seconds off” ringing pattern and connecting to “C” and “B” terminals provides a “1 second off/3 seconds on” ringing pattern. 2.
Section 300-Installation Chapter 5. Peripheral Equipment Power Failure Unit Guidelines • Up to four SLTs can be connected to the Power Failure Unit (VA-43703). If a power failure occurs, the SLTs will automatically receive dial tone directly from the central office. DBS features and restrictions do not apply when the SLTs are receiving dial tone from the CO. • If a call is in progress through the Power Failure Unit (PFU) when the power is restored, the call will be disconnected.
Chapter 5. Peripheral Equipment Section 300-Installation Figure 5-10. Cable punch-out plate, Power Failure Unit 3. Mount the PFU on the wall using the three screws provided with the unit. (See Figure 5-11.) 4. Connect the trunks from the central office to the PFU. 5. Connect the SLTs to the AEC extension ports on the PFU. 6. Connect the trunks from the DBS to the PFU. 7. Connect the AEC ports from the DBS to the PFU.
Section 300-Installation Chapter 5. Peripheral Equipment Figure 5-11. Power Failure Unit (PFU) installation 5/16 in. From the M ain C abinet AEC AEC AEC AEC Extension PortN o.A Extension PortN o.B Extension PortN o.C Extension PortN o.D To the M ain C abinet TR K TR K TR K TR K PortN o.A PortN o.B PortN o.C PortN o.D CN5 AEC AEC AEC AEC Extension PortN o.A Extension PortN o.B Extension PortN o.C Extension PortN o.
Chapter 5. Peripheral Equipment Section 300-Installation Voice Announce Unit (VAU) Guidelines • Operating temperatures for the Voice Announce Unit (VB-43708) should be between 35 and 105 ° F. • Maximum loop resistance for the VAU is 10 Ohms. • The VAU contains a rechargeable lead-acid battery. Recharging circuity for the battery is included on the VAU. • The ports used for the VAU must have all FF key assignments cleared before voice messages and abbreviated dial numbers are programmed.
Section 300-Installation Chapter 5. Peripheral Equipment Table 5-7. Switch settings for delay answer timing, VAU Switch Block 2 (SW2) Delay Answer Timer (Switches 1-3) Switch 4 1 2 3 8 12 Timer (in seconds) 16 20 24 28 No Answer (VAU 1.1 or below) or Immediate Answer (VAU 1.2 or above) OFF OFF OFF OFF ON ON ON ON OFF OFF ON ON OFF OFF ON ON OFF ON OFF ON OFF ON OFF ON Table 5-8. Switch settings for DTMF detection timing, VAU DTMF Detection Timer VAU Version 1.1 or above 1.
Chapter 5. Peripheral Equipment Section 300-Installation Table 5-10. Switch settings for abbreviated dialing digit length, VAU Switch Block 2 (SW2) Abbreviated Dialing Digit Length (Switches 7-8) Switch 7 8 Number of Digits 1 Digit OFF OFF 2 Digits OFF ON 3 Digits ON OFF 3. Remove the cable punch-out plate (Figure 5-12) to make an opening for the cable coming into the VAU. To remove the plate, cut the grooves on either side with diagonal shears.
Section 300-Installation Chapter 5. Peripheral Equipment Figure 5-13. Extension cord connection to the VAU BK R CN1 on the bottom of the VAU G Y Port 1 Port 2 6. Install the cover on the VAU. Figure 5-14. Voice Announce Unit (VAU) installation 5/16 in SW 2 SW 1 CN1 Voice Announce U nit (VB-43708) DBS-2.3/9.
Chapter 5. Peripheral Equipment Section 300-Installation Recording and Playing Messages You can record the VAU messages from either an extension or a trunk. Notes: You must use a DTMF telephone to record and play VAU messages. To change existing messages, record over them. To record and play messages, complete the following steps. 1. Do one of the following: If . . . Then . . . You are recording or playing from an extension Take your phone off hook. Dial the VAU extension number.
Section 300-Installation Chapter 5. Peripheral Equipment Door Box Adaptor (Trunk Port) Guidelines There are two types of door phone adaptors available for the DBS. The first type (VB-43701) utilizes a trunk connection to connect to the door box and is described below. The second type (VB-43711) utilizes a digital port extension to connect to the door box and door opener. See“Door Box Adaptor (Extension Port)” on page 5-31 for more information.
Chapter 5. Peripheral Equipment Section 300-Installation Requirements • Trunks used for Door Boxes and openers must be set up as dial pulse trunks. • Equipment combinations used with the Door Box Adaptor require the number of trunks in the following table: If you use . . .
Section 300-Installation Chapter 5. Peripheral Equipment Figure 5-15. Cable punch-out plate, Door Box Adaptor 4. Mount the Door Box Adaptor on the wall using the three screws provided with the unit. 5. Connect the trunk line(s) to the Door Box Adaptor, as shown in Figure 516. The “CO.D” connector is used for the Door Box and opener. The “CO.S” connector is used for the sensor. 6. Connect the Door Box, door opener, and sensor to the Door Box Adaptor. DBS-2.3/9.
Chapter 5. Peripheral Equipment Section 300-Installation Figure 5-16.
Section 300-Installation Chapter 5. Peripheral Equipment Door Box Adaptor (Extension Port) Note: There are two types of door phone adaptors available for the DBS. The first type (VB-43701) utilizes a trunk connection to connect to the door box. See “Door Box Adaptor (Trunk Port)” on page 5-27 for more information. The second type (VB-43711) utilizes a digital port extension to connect to the door box and door opener and is described below.
Chapter 5. Peripheral Equipment Section 300-Installation Figure 5-18. Installation of the door box, door opener Contact Ratings for Opener 120V AC: 0.3 amps 30V DC: 1 amp 4. Connect the extension line to the Door Box Adaptor, as shown in Figure 5-19. 5-32 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 5. Peripheral Equipment Figure 5-19. Connections to the Door Box Adaptor 5. Connect the Door Box and door opener to the Door Box Adaptor. DBS-2.3/9.
Chapter 5. Peripheral Equipment Section 300-Installation Single Line Telephone Adaptor Guidelines • The Single Line Telephone Adaptor (SLTA, VB-43709) provides an alternative way of connecting analog DTMF telephones (2500 sets). One SLTA supports up to 4 Single Line Telephones. • Each SLT extension requires a digital extension port connection to the SLTA. Installation 1. Remove the cover from the SLTA. 2.
Section 300-Installation Chapter 5. Peripheral Equipment Table 5-11. Maximum distances for SLTA installation Wiring gauge Max. distance (in feet) between the DBS and SLTA Max. distance (in feet) between the SLTA and the SLT AWG 22 300’ or 10 W 3000’ or 100 W AWG 24 190’ or 10 W 1900’ or 100 W AWG 26 120’ or 10 W 1200’ or 100 W 4. If the DBS is powered up, turn off the power. 5. Connect the GND and +24V leads on the SLTA to the DBS connector panel.
Chapter 5. Peripheral Equipment Section 300-Installation Figure 5-21. SLTA installation 5/16 in. To +24V on D B S C N 2 C onnector To G N D on DBS C N2 C onnector To S LT A and B D BS E xt.P ort A and B D BS E xt.P ort C and D To S LT C and D SLTA (VB-43709) CN1 BK Y BK RG T 5-36 BK Y R T Ext B T R T Ext D Y BK R T R SLT "B" Y RG T SLT "A" Ext C R CN4 RG RG Ext A T CN3 CN2 R SLT "C " R DBS Manual - Revised April 2000 T SLT "D " R DBS-2.3/9.
Chapter 6. Double-Cabinet Systems Two DBS cabinets can be connected in order to increase capacity. This chapter includes connection procedures, as well as capacities for two-cabinet systems. See Chapter 4 for instructions on installing T1s in two-cabinet systems. This chapter covers the following topics: DBS-2.3/9.
6-2 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 6. Double-Cabinet Systems Guidelines • Two DBS cabinets can be connected to increase line size. The maximum line size consists of two DBS 96 cabinets, which provide 192 ports. • CPC-B and SCC-B are required for two-cabinet systems. • If ground start or DID trunks are used in both cabinets, separate -48V supplies must be supplied for each cabinet. If AECs are used in both cabinets, separate SLT ringer boxes must be supplied for each cabinet.
Chapter 6. Double-Cabinet Systems Section 300-Installation Figure 6-1. Slot usage for two-cabinet systems, DBS 40 + DBS 40 DBS 40 (Slave) CBL-S MFR# MFR# SCC CPC AUX1 AUX2 N/A TRK 17-24* or EXT 49-56 EXT 41-48 EXT 33-40 EXT 25-32 TRK 9-16 TRK1 EC1 EC2 EC3 EC/TRK DBS 40 (Master) CBL-M MFR# or API CPC-B SCC CPC AUX1 AUX2 SCC-B N/A EXT 17-24 EXT 9-16 EXT 1-8 TRK 1-8 TRK1 EC1 EC2 EC3 EC/TRK Notes: *See “T1 Interface” on page 4-11 for EC/TRK port numbers for T1.
Section 300-Installation Chapter 6. Double-Cabinet Systems Figure 6-2.
Chapter 6. Double-Cabinet Systems Section 300-Installation Figure 6-3.
Section 300-Installation Chapter 6. Double-Cabinet Systems Figure 6-4.
Chapter 6. Double-Cabinet Systems Section 300-Installation Figure 6-5.
Section 300-Installation Chapter 6. Double-Cabinet Systems Figure 6-6.
Chapter 6. Double-Cabinet Systems Section 300-Installation Installation 1. Install the trunk and extension cards according to the layouts shown in the Figures 6-1 through 6-6. Note: The port numbers for each slot are fixed. 2. If you are using two MFR cards, cut Strap S3 on the second card. Figure 6-7. Strap 3, MFR card S3 M FR C ard 3. Using the cables provided, connect the CBL-M card in the master cabinet to the CBL-S card installed in the slave cabinet.
Section 300-Installation Chapter 6. Double-Cabinet Systems Figure 6-8. Double-cabinet installation Slave C abinet RS-232C D igital D eskset Program m ing Phone M odem Program m ing Term inal or SM D R Printer To C O EM I Filters M DF Rem ote PC AS SLT Lines RS-232C RS-232C Adapter M aster C abinet PC (AC D or VM S) EM I Filters 4. Connect two 24V power supply cords from the CBL-S card to the 24V and GND terminals on CN2 of the Connector Panel of the slave cabinet. Figure 6-9.
Chapter 6. Double-Cabinet Systems Section 300-Installation 5. Set SW1 on the CBL-M card according to the following table. Table 6-2.
Chapter 7. Specifications This chapter contains frequently referenced DBS specifications. Note: All maximums may not be attainable simultaneously. Also, attainment of some maximums depends on levels of feature usage and optional hardware requirements. Though every effort has been made to ensure the accuracy of these specifications, Panasonic does not warrant them in regard to merchantability or fitness for a particular purpose. Specifications are subject to change without notice.
7-2 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Chapter 7. Specifications Electrical Characteristics Table 7-1. Input power Equipment Power Requirements All DBS cabinets DBS key phones 120V AC ± 10 % 60 Hz 3 watts maximum (powered from the DBS) DBS 96 + DBS 96 DBS 96 + DBS 72 DBS 96 + DBS 40 DBS 72 + DBS 72 DBS 72 + DBS 40 DBS 40 + DBS 40 DBS 96 DBS 40 System Status DBS 72 Table 7-2. Power consumption and heat generation Power Consumption (in Watts) With no traffic With max.
Chapter 7. Specifications Section 300-Installation Environmental Requirements Table 7-4. Temperature and humidity requirements Environmental Conditions Requirements Temperature Relative Humidity 32 to 104° F (0 to 40° C) 30 to 90% Table 7-5. Dimensions and weight, single-cabinet systems and phones Physical Characteristics DBS 40 DBS 72 DBS 96 Dimensions (H x W x D in inches) Cabinet VB-43225 Other key phones DSLT DSS/72 EM/24 Cabinet VB-43225 Other key phones DSLT DSS/72 EM/24 21 x 15 x 9.
Section 300-Installation Chapter 7. Specifications Resource Maximums Trunk ports Extension ports Expansion ports Trunk/Extension speech path switching Notes: 8 16 24 24 48 64 8 8 8 nonblocking 16 48 8 24 72 0 32 96 8* 32 88 16 40 112 16 DBS 96 + DBS 96 DBS 96 + DBS 72 DBS 96 + DBS 40 DBS 72 + DBS 72 DBS 72 + DBS 40 DBS 40 + DBS 40 DBS 96 DBS 40 System Resources DBS 72 Table 7-7.
Chapter 7. Specifications Section 300-Installation Resource Maximums Conference circuits SCC-A SCC-B with CPC-B SCC-B with CPC-A and CPC-AII 3 four-party circuits 8 four-party circuits 3 four-party circuits DISA No. of incoming authorization codes No.of outgoing authrorization codes No.of digits in each authorization code 1 2 4 Hunting No. of groups No. of stations in a group 8 8 Least cost routing No.
Section 300-Installation Chapter 7. Specifications Resource Maximums Paging (continued) No. of external paging zones No. of stations in external paging zone 00 No. of stations in external paging zones 01-04 5 No. of stations in the system No. of stations in corresponding paging group 01-04 Speed dial No. of personal speed dial numbers No. of system speed dial numbers 10 per extension 90 (00 ~ 89) or 200 (000-199) with CPC-AII and CPC-B Version 7.0 16 No.
Chapter 7. Specifications Part No. Section 300-Installation Description Quantity DBS 40 VB-43310 VB-43320 Phone Options 24-key expansion module (EM24) 72-key DSS/BLF module (DSS/72) VB-43884 VB-43885 VB-43886 VB-43890 7 ft. handset cord 15 ft. handset cord 25 ft.
Section 300-Installation Part No. Chapter 7.
Chapter 7. Specifications Section 300-Installation Table 7-10. Hardware maximums for double-cabinet systems DBS 72 + DBS 72 DBS 96 + DBS 40 DBS 96 + DBS 72 DBS 96 + DBS 96 Quantity DBS 72 + DBS 40 Description DBS 40 + DBS 40 Part No.
Section 300-Installation VB-43110 VB-43410 VB-43411 VB-43412 VB-43420 VB-43421 VB-43431 VB-43510 VB-43511 VB-43541 VB-43531 VB-43561 VB-43562 VB-43563 VB-43611 VB-43621 VB-43551 DBS 96 + DBS 96 DBS 96 + DBS 72 DBS 96 + DBS 40 DBS 72 + DBS 72 Quantity DBS 72 + DBS 40 Description DBS 40 + DBS 40 Part No. Chapter 7. Specifications Printed Circuit Cards Cable kit for 2-cab.
Chapter 7.
Section 300-Installation Chapter 7. Specifications Cabling Specifications Table 7-11.
Chapter 7. Specifications Section 300-Installation Communication Parameters Table 7-12. Voice path from KTELs to DBS Channel Speed Overall communications path D-channel data B-channel data 256 kbps 16 kbps 64 kbps Table 7-13. Data communications ports Port Parameters SMDR Interface Baud rate Parity Stop bit length Data bit length Baud rate Stop bit length Data bit length Parity Maintenance (RAI card) 7-14 RS232-C 300, 1200, 4800 or 9600 kbps Even, odd, or none 1, 1.
Section 300-Installation Chapter 7. Specifications Signaling Characteristics Table 7-14. Signaling to CO Item Dial pulse Break ratio Minimum pause Trunk start Specification 8 to 11 pulses per second (PPS) 58 to 64% 0.7 to 1.0 seconds Loop or ground start Table 7-15.
Chapter 7. Specifications Section 300-Installation Tone Characteristics Table 7-17. Tone Plan Tone Name CO incoming call Hold recall Transfer recall Trunk queuing CO offhook signal Frequency CO Call Tones 550/400 Hz at 16 Hz Programmable 550/400 Hz at 16 Hz 0.5 on/3.5 off 550/400 Hz at 16 Hz 0.5 on/3.5 off 550/400 Hz at 16 Hz 0.5 on/0.5 off/0.5 on/2.
Section 300-Installation Tone Name Dial tone Ringing Busy Voice mail ringing Chapter 7. Specifications Frequency 400 Hz 400 Hz 400 Hz 550/400 Hz at 16 Hz Timing (seconds) Continuous 1 on/3 off 0.5 on/0.5 off 2 on/2 off Table 7-18. DTMF frequencies DBS-2.3/9.
Chapter 7. Specifications 7-18 Section 300-Installation DBS Manual - Revised April 2000 DBS-2.3/9.
Appendix A: CPC-EX 1.0 Updates CPC-EX Version 1.0 (and above) offers the following enhancements to the DBS phone system: Compatibility CPC-EX Version 1.0 supports all features of CPC-B Version 7.1 (with the exception of TSAPI support). In addition, CPC-EX Version 1.0 adds support for additional features, including the 44-Series phones, T1 Networking, and ISDN. The CPC-EX card can be installed into an existing DBS cabinet, with no hardware modifications.
Appendix A. EX 1.0 Feature Update Section 300-Installation Enhanced DBS features that can be executed on the 44-Series phones are described below: Directory Mode On the small-display phones, you can scroll through SSD names, PSD names, or extension names and select a displayed name for dialing.
Section 300-Installation Appendix A. EX 1.0 Feature Update FF-Key Programming Because T1 Networking adds the capability of 4-digit extension numbering, you can now program up to 8 digits (not 6) into an FF-key. Speed Dial Enhancements CPC-EX supports up to 500 System Speed Dial (SSD) numbers. CPC-EX also allows SSD codes to be chained, or “linked”, to another SSD number, and either PSD or SSD codes to be chained to a PSD number.
Appendix A. EX 1.0 Feature Update Section 300-Installation SMDR Modifications SMDR reports contain several additional call types and other parameters due to CPC-EX support of T1 Networking and ISDN calls. ISDN Support CPC-EX supports ISDN-PRI (Integrated Services Digital Network -- Primary Rate Interface). The program address for Trunk Circuit Type (FF2 (trunk #)# 21#) has been modified to allow for ISDN. Programming addresses have also been added in CPC-EX to support ISDN.
Section 300-Installation Appendix A. EX 1.0 Feature Update Figure A-1 CPC-EX TRK1 TRK2 TRK3 EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/TRK SCC CPC AUX1 AUX2 SERIAL PO RT 2 STATU S LED SW 1 RAM H O LD RAM C LR Key Telephone Installation Desi Strip Cover The 44-Series Key Telephones are shipped with a thin green protective film over the Desi strip cover. Be sure to remove this film from both sides of the Desi cover before placing the phone in service.
Appendix A. EX 1.0 Feature Update Section 300-Installation Figure A-2.Desk Stand Removal. Step 3 Step 2 4. Rotate the desk stand 180°. In this position it doubles as a wall mount bracket. 5. Insert the wall mount bracket into the mounting guides as shown in Figure A-3. 6. Slide the wall mount bracket onto the telephone. Figure A-3.Inserting the wall mount bracket (rotated desk stand) Step 6 Step 5 7.
Section 300-Installation Appendix A. EX 1.0 Feature Update 8. Slide the handset guide out, rotate 180° so that the holding clip is exposed, and reinsert. Figure A-4.Handset guide insertion for wall mounting, key telephone 44-Series Enhanced Phone Features Note: The enhanced features introduced with these phones are supported by CPC-EX Version 1.0, CPC-AII/B Version 8.0, and CPC-S/M Version 2.0. You can also use the 44-Series phones with previous DBS versions, but the enhanced features won’t be supported.
Appendix A. EX 1.0 Feature Update Section 300-Installation Figure A-5.44-Series Small-Display Phone 1 2 3 M ODE EN D 4 08:24 Tue N O V 14 Sandy 173 5 PR O G 6 CO NF 7 8 22 DIGITAL BUSINESS SYSTEM 9 1 4 G HI 7 PR S * 18 2 ABC 5 JKL TU V 8 3 D EF 6 M NO 9 D N D /C F R ED IAL 10 M U TE M U TE 11 W XY EXT FLASH S peakerphone 15 AU TO 16 12 OPER 0 14 O N /O FF 13 17 H O LD VO LU M E 19 20 21 Table A-2.
Section 300-Installation # 8 9 Feature One-Touch Keys 10 Flexible Function (FF) Keys DND/CF Indicator 11 MUTE Indicator 12 EXT Indicator 13 14 15 ON/OFF Indicator REDIAL Key MUTE Key 16 AUTO Key 17 18 ON/OFF Key FLASH Key 19 VOLUME Key 20 HOLD Key 21 Microphone 22 Speaker DBS-2.3/9.2-300 Appendix A. EX 1.0 Feature Update Description Used to make outside calls or to access call-handling features. Used to access outside lines or to access call-handling features.
Appendix A. EX 1.0 Feature Update Section 300-Installation Figure A-6.
Section 300-Installation # 6 Feature MENU Key 7 8 9 PREV Key NEXT Key PROG Key 10 11 Flexible Function (FF) Keys DND/CF Indicator 12 MUTE Indicator 13 EXT Indicator 14 15 16 ON/OFF Indicator REDIAL Key MUTE Key 17 AUTO Key 18 19 ON/OFF Key FLASH Key 20 VOLUME Key 21 HOLD Key 22 Microphone 23 Speaker DBS-2.3/9.2-300 Appendix A. EX 1.0 Feature Update Description Used to return to the Main Menu screen.
Appendix A. EX 1.0 Feature Update Section 300-Installation Analog Adapter Description The Analog Adapter (VB-44100) consists of a base adapter and PC board which is installed on the underside of the phone. It is used to connect the 44-Series large-display phone to an analog device such as an SLT telephone, cordless phone, FAX machine, or modem. This allows the same phone line to be used to alternate between normal phone calls and analog communications.
Section 300-Installation Appendix A. EX 1.0 Feature Update • The “*71” code will not work if FF3 (ExtPort)# 51# is set to “0”. • If set to “Analog port RING”, the large-display phone will work like an SLT/OPX (no page announcements, no voice calls from other extensions, etc.). • If the phone is in CF/DND (Call-Forward or Do Not Disturb), the phone will remain in CF/DND even if the ringing device is changed via the *71 code.
Appendix A. EX 1.0 Feature Update Section 300-Installation has been received, pressing the MSG key will perform auto-callback in the order received. • Auto-Answer Voice Message. You can press the MSG key to automatically access your voice mailbox. The phone will dial your voice mailbox and send access codes (if programmed) for retrieving messages. Operation To Program Voice Mailbox Access Codes into the MSG Key: Press PROG MSG [16-digit number] HOLD The display will reflect “Regist Data”.
Section 300-Installation Appendix A. EX 1.0 Feature Update etc.), the Voice Mailbox Access Code must be reprogrammed into the MSG key. DSS/72 Console - Key Arrangement Description The keys on the DSS/72 Console (VB-44320) are arranged differently from the VB-43320 model. The DSS console has 6 columns x 12 rows of keys (not 8 columns x 9 rows as in the previous version). This affects the following: • Name and Message Assignments (FF6 addresses). The alphabetical arrangement of the keys is different.
Appendix A. EX 1.0 Feature Update Section 300-Installation Figure A-7.
Section 300-Installation Appendix A. EX 1.0 Feature Update Figure A-8.
Appendix A. EX 1.0 Feature Update Section 300-Installation Figure A-9.EM/24 Unit (VB-44310) keys Operation Page A-18 FF12 FF24 FF11 FF23 FF10 FF22 FF9 FF21 FF8 FF20 FF7 FF19 FF6 FF18 FF5 FF17 FF4 FF16 FF3 FF15 FF2 FF14 FF1 FF13 The 44-Series EM/24 operates the same as previous models. DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Appendix A. EX 1.0 Feature Update Additional Serial Port on CPC Card Description The CPC-EX card contains an on-board serial port (Serial Port 2) which can be used for Bus Monitor/ Remote Maintenance. This serial port (labeled CN5) is located just above the LEDs on the front of the card (see the illustration on Appendix A:-4).
Appendix A. EX 1.0 Feature Update Notes Section 300-Installation • Serial Port 2 requires a special interface cable. • Serial Port 2 can be used for Bus Monitor/Maintenance only. You must continue to use the backplane port (Serial Port 1) for SMDR. • Port selections are made from the Attendant phone as follows: dial #90 dial #92 dial #93 to set Serial Port 1 for... Bus Monitor/Maintenance SMDR SMDR/Maintenance and Serial Port 2 for...
Appendix B: CPC-AII/B 8.0 Updates CPC-AII/B Version 8.0 offers support for the Panasonic 44-Series telephones (VB-44xxx), as well as Computer Telephony Integration (CTI) through the Windows™ Telephony Applications Processing Interface (TAPI). DBS-2.3/9.
Appendix B. CPC-AII/B 8.0 Feature Update Section 300-Installation Contents Topic 44-Series Phone Support Enhanced Phone Features Page B-2 Page B-3 B-4 Analog Adapter B-8 MSG (Message) Key B-9 DSS/72 Console - Key Arrangement B-10 EM/24 - Key Arrangement B-13 TAPI Support B-14 Key Telephone Installation Notes B-14 DBS Manual - Revised April 2000 DBS-2.3/9.
Section 300-Installation Appendix B. CPC-AII/B 8.0 Feature Update 44-Series Phone Support CPC-AII/B Version 8.0 provides full support for Panasonic’s 44-Series phones (VB-44xxx). Table D-1, below, lists all 44-Series phone models and their part numbers. Most models are available in two colors: gray and black. Table B-1.
Appendix B. CPC-AII/B 8.0 Feature Update Section 300-Installation Enhanced Phone Features Enhanced DBS features that can be executed on the 44-Series phones are described below: Note: The features introduced with these phones are supported by CPC-AII/B Version 8.0, CPC-S/M Version 2.0, and CPC-EX Version 1.0. You can also use the 44Series phones with previous DBS versions, but the enhanced features won’t be supported. Figure B-11.
Section 300-Installation Appendix B. CPC-AII/B 8.0 Feature Update Table B-2.Key to 44-Series Small-Display Phone # 1 2 Feature Message Indicator Display 3 Mode Key 4 End Key 5 Select Keys 6 PROG Key 7 CONF Key 8 One-Touch Keys 9 10 Flexible Function (FF) Keys DND/CF Indicator 11 MUTE Indicator 12 EXT Indicator 13 14 15 ON/OFF Indicator REDIAL Key MUTE Key 16 AUTO Key 17 18 ON/OFF Key FLASH Key 19 VOLUME Key 20 HOLD Key 21 Microphone 22 Speaker DBS-2.3/9.
Appendix B. CPC-AII/B 8.0 Feature Update Section 300-Installation Figure B-12.
Section 300-Installation # 6 Feature MENU Key 7 8 9 PREV Key NEXT Key PROG Key 10 11 Flexible Function (FF) Keys DND/CF Indicator 12 MUTE Indicator 13 EXT Indicator 14 15 16 ON/OFF Indicator REDIAL Key MUTE Key 17 AUTO Key 18 19 ON/OFF Key FLASH Key 20 VOLUME Key 21 HOLD Key 22 Microphone 23 Speaker DBS-2.3/9.2-300 Appendix B. CPC-AII/B 8.0 Feature Update Description Used to return to the Main Menu screen.
Appendix B. CPC-AII/B 8.0 Feature Update Section 300-Installation Analog Adapter 44-Series phones only CPC-AII/B Version 8.0, CPC-S/M Version 2.0, or CPC-EX Version 1.0 only Description The Analog Adapter (VB-44100) consists of a base adapter and PC board which is installed on the underside of the phone. It is used to connect the 44-Series large-display phone to an analog device such as an SLT telephone, cordless phone, FAX machine, or modem.
Section 300-Installation Appendix B. CPC-AII/B 8.0 Feature Update • The “*71” code will not work if the other device is in use. • The “*71” code will not work if FF3 (ExtPort)# 51# is set to “0”. • If set to “Analog port RING”, the large-display phone will work like an SLT/OPX (no page announcements, no voice calls from other extensions, etc.). • If the phone is in CF/DND (Call-Forward or Do Not Disturb), the phone will remain in CF/DND even if the ringing device is changed via the *71 code.
Appendix B. CPC-AII/B 8.0 Feature Update Operation Section 300-Installation To Program Voice Mailbox Access Codes into the MSG Key: Press PROG MSG [16-digit number] HOLD The display will reflect “Regist Data”. To Confirm a Voice Mailbox Access Code Programmed into the Message Key.. Press CONF MSG. The programmed access code will be displayed. Notes Operation With Message Waiting Indicator.
Section 300-Installation Appendix B. CPC-AII/B 8.0 Feature Update columns x 12 rows of keys (not 8 columns x 9 rows as in the previous version). This affects the following: • Name and Message Assignments (FF6 addresses). The alphabetical arrangement of the keys is different. • FF-Keys. The FF-keys on the DSS/72 console are numbered left-toright, bottom row first. • DSS #1 Defaults. The default extension number assignments on DSS #1 are different.
Appendix B. CPC-AII/B 8.0 Feature Update Section 300-Installation Figure B-14.
Section 300-Installation Appendix B. CPC-AII/B 8.0 Feature Update EM/24 - Key Arrangement 44-Series phones only CPC-AII/B Version 8.0, CPC-S/M Version 2.0, or CPC-EX Version 1.0 only Description The keys on the enhanced EM/24 unit (VB-44310) are arranged differently from the VB-43310 model. The enhanced EM/24 unit has 2 columns x 12 rows of keys (not 3 columns x 8 rows as in the previous version). This affects the following: • FF-Keys.
Appendix B. CPC-AII/B 8.0 Feature Update Operation Section 300-Installation The 44-Series EM/24 operates the same as previous models. TAPI Support CPC-AII/B offers full support for the Panasonic Telephony Applications Processing Interface (TAPI). TAPI is a Windows™ application which allows a PC to be connected to a telephone extension and used to control incoming and outgoing calls through that extension.
Section 300-Installation Appendix B. CPC-AII/B 8.0 Feature Update Figure B-16.Desk Stand Removal. Step 3 Step 2 4. Rotate the desk stand 180°. In this position it doubles as a wall mount bracket. 5. Insert the wall mount bracket into the mounting guides as shown in Figure D-17. 6. Slide the wall mount bracket onto the telephone. Figure B-17.Inserting the wall mount bracket (rotated desk stand) Step 6 Step 5 7.
Appendix B. CPC-AII/B 8.0 Feature Update Section 300-Installation Figure B-18.Handset guide insertion for wall mounting, key telephone Page B-16 DBS Manual - Revised April 2000 DBS-2.3/9.
Index A Analog extensions 4-37 guidelines 4-37 installation 4-37 see also SLTA B Background music see Peripheral equipment, BGM Battery backup capacities 7-3 guidelines 3-9 installation 3-9 DBS 40 3-10 DBS 72 and 96 3-11 part numbers 3-9 specifications 7-3 BGM see Peripheral equipment, BGM C Cabinet description 2-3 Cabinet installation 3-1 batteries 3-9 guidelines 3-9 installation DBS 40 3-10 DBS 72 and 96 3-11 circuit cards 3-6 guidelines 3-6 installation 3-8 DSLT wall mounting 3-15 desk stand attachment
Index Section 300-Installation D DTMF frequencies 7-17 Data communications ports 7-14 DBS cabinet description 2-3 configurations 2-5 model numbers 1-1 requirements 1-1 DID trunks 4-9 guidelines 4-9 installation 4-10 Digital extension see DSLT Dimensions of system 7-4 Door 5-27, 5-31 Door box 5-31 Door box adaptor 5-31 Door box adaptor (extension port) 5-31 Door box adaptor (trunk port) see Peripheral equipment, door box adaptor (Trunk Port) Door phone 5-31 see Peripheral equipment, door box adaptor (tru
Section 300-Installation Index G Gas and airborne particles 1-4 Grounding 1-5, 3-5 guidelines 3-5 installation 3-5 T1 4-26 Ground-start trunks 4-9 guidelines 4-9 installation 4-10 H Hardware maximums double-cabinet systems 7-10 single-cabinet systems 7-7 Heat generation 7-3 Humidity 1-4, 7-4 I Initialization of system 3-17 Input power 7-3 Installation analog extensions 4-37 background music 5-8 cabinet 3-1 batteries 3-9 DBS 40 3-10 DBS 72 and 96 3-11 guidelines 3-9 grounding 3-5 guidelines 3-5 installat
Index Section 300-Installation see Extensions maximums 7-5 Local Terminal see Peripheral equipment, local terminal Loop-start trunks 4-7 guidelines 4-7 installation 4-7 M Maximums cabling distances 7-13 double-cabinet systems 6-3 feature-related 7-5 hardware double-cabinet systems 7-10 single-cabinet systems 7-7 lines 7-5 MFR cards in double-cabinet system 6-4, 6-5, 6-6, 6-7, 6-8, 6-9 OPX adaptor distances 5-11 OPX direct connect distances 5-10 system resources 7-5 T1 4-12 T1 trunk assignments 4-14, 4-15
Section 300-Installation Index paging guidelines 5-14 installation 5-14 PCAS terminal guidelines 5-3 installation 5-4 RS-232 connection 5-4 power failure unit guidelines 5-19 installation 5-19 RAI guidelines 5-6 installation 5-6 SMDR device guidelines 5-3 installation 5-4 RS-232 connection 5-4 voice announce unit guidelines 5-22 installation 5-22 PFU see Peripheral equipment, power failure unit Ports for data communications 7-14 Power consumption 7-3 Power failure unit see Peripheral equipment, power fail
Index Section 300-Installation configurations 2-5 initialization 3-17 overview 2-1 requirements 1-1 T T1 interface 4-11 clock sync cable 4-29 distance from DBS to CSU 4-24 fractional T1 4-13 grounding 4-26 guidelines 4-11 hardware requirements 4-11 maximums 4-12 trunk assignments for double-cabinet systems 4-15 trunk assignments for single-cabinet systems 4-14 installation 4-20 double cabinet T1 in both cabinets 4-29 T1 in slave 4-27 single cabinet 4-21 MDF card 4-23 RJ48 pinouts 4-25 sync cable 4-24, 4-
Section 300-Installation Index see Peripheral equipment, voice announce unit Voice path from KTEL to DBS 7-14 W Wall mounting cabinets 3-3 cover removal 3-3 guidelines 3-3 installation 3-3 mounting brackets 3-4 mounting illustration 3-4 DSLT 3-15, 3-16 key phones 3-13 mount adaptor removal 3-13 mount adaptor replacement 3-14 Water exposure 1-4 Weight of system 7-4 DBS-2.3/9.
Index Index-8 Section 300-Installation DBS Manual - Revised April 2000 DBS-2.3/9.
