Datasheet

677
Dual Display Digital Pressure Sensor DP-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
PLC /
TERMINALS
HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Pressure/
Digital Display
Pressure/
Head-separated
Flow
Other
Products
DP-100
DP-M
PRECAUTIONS FOR PROPER USE
Refer to General precautions.
•The MS-DP1-4 panel mounting bracket is available when
switching from the DP2 / DP3 series.
•If connecting a commercially-available
coupling to the pressure port, attach a
12 mm 0.472 in spanner (14 mm 0.551
in spanner for DP-100-E type) to the
hexagonalsectionofthepressureport
to secure it, and tighten at a torque of
9.8 N·m or less. If it is tightened using
excessivetorque,itmaydamagethe
coupling or the pressure port.
In addition, wrap sealing tape around
the coupling when connecting it to prevent leaks.
•If connecting a commercially-available joint to the pressure
port of the DP-10□-M, hold the main unit in your hand to
steady it, and tighten to a torque of 1.0 N·m or less. If it is
tightenedtoanexcessivetorque,thejointorthemainunit
may become damaged.
•If connecting a commercially-available joint to the pressure
port of the MS-DP1-7, tighten to a torque of 9.8 N·m or less.
•Make sure to mount MS-DP1-F□ with the sensor properly.
If it is not mounted properly, air leakage may occur.
•Takecarethattheexcessivemountinganddismountingof
this product may cause deterioration of the O-ring.
•If you touch the O-ring of MS-DP1-F□, or any scratch or
dust, etc. is attached to it, air leakage may occur and the
sensing performance may deteriorate.
TakesufcientcarewhenusingandstoringMS-DP1-F□.
•The tightening torque should be 1 N·m or less when
connecting a coupling to the pressure port of MS-DP1-FM.
•When connecting the coupling to the pressure port of
MS-DP1-FR/FE/FN, hold the pressure port with a 14 mm
0.551 in spanner and make sure that the tightening
torque is 9.8 N·m or less.
In addition, in order to prevent any leakage, wind a
sealing tape on the coupling when connecting.
•An conversion bushing is available for when using the
DP-10□-M short pressure port type. It can be used to
switch between this model and the DP2 / DP3 series. When
connecting to the pressure port, use a tightening torque of
1.0 N·m or less.
•The MS-DP1-F□atattachmentisavailable.
If using the MS-DP1-F□atattachment(optional),install
by following the procedures given below.
1
Decide the direction of this product to mount with the sensor.
2
Mount this product with the M3 female threads of the sensor
by using the attached M3 (length 8 mm 0.315 in) screws.
The tightening torque should be 0.5 N·m or less.
3
Mount this product with the mounting surface by using the attached
M4 (length 20 mm 0.787 in) screws. The tightening torque should
be 1.2 N·m or less.
Mounting Piping
Flat attachment
DP2-20
ñ101.3kPa
OUT2
OUT1
MODE
0-ADJ
Front protective cover
DPX-04 (Optional)
can be installed on
MS-DP1-4.
DP2 / DP3
DP-100
Insert
Remove
Remove
Panel mounting bracket MS-DP1-4
Mounting holes
for DP2 / DP3 series
can be used as is.
Conversion bushing MS-DP1-7
M5 female thread Rc1/8 female thread
Note: It is not possible to mount this product such
that the pressure port faces upward.
Pressure port
faces downward
Pressure port
faces leftward
Pressure port
faces rightward
Pressure port
faces upward
M3 (length 8 mm 0.315 in)
screw (Accessory)
M3 female thread
M3 female thread
Connector attached cable
Groove
M4 (length 20 mm 0.787 in)
screw (Accessory)
Note: Take care that if the cable with connector is sticking out of the side
groove of this product when mounting, the cable may disconnected.
Connector attached cable
Groove
M4 (length 20 mm 0.787 in)
screw (Accessory)
Note: Take care that if the cable with connector is sticking out of the side
groove of this product when mounting, the cable may disconnected.
12 mm 0.472 in
spanner
14 mm 0.551 in
spanner
Coupling (Purchase separately.)
Pressure port
14 mm 0.551 in
spanner
Note: Do not tighten the pressure port by holding the product with the spanner.
It may cause the product breakage.