Panasonic Broadcast BT-LT1700 Menu Information
How to Use the On Screen Menu Three types of information are displayed on the screen. The input signal status, picture adjusting knob status, and the menu display. Input signal status 1 1. The selected input line (J page 7, ) • VIDEO, Y/C, SDI1, SDI2, YPBPR/RGB-VIDEO/RGB-COMP. 2. Signal format • The display status can be set in “STATUS DISPLAY” in the “SYSTEM CONFIG” menu (J page 18).
How to Use the On Screen Menu (continued) Menu operations 1. Push [MENU] to display the MAIN menu. 3. Push [ , ] to select the sub menu, then push [ENTER]. The setting values in the sub menu change to green. MARKER MARKER 16:9 MARKER 4:3 MARKER BACK CENTER MARKER GPI PRESET1 GPI PRESET2 2. Push [ , [ENTER]. OFF OFF NORMAL OFF 80% 80% ] to select the menu, then push 4. Push [ , ] to select the setting values, then push [ENTER]. Push [MENU] to cancel.
User Data You can change the menu setting values and picture adjusting knob settings, then save and load up to 5 combinations of screen adjustment values as user data. You can also return the setting values and adjustment values to the factory preset settings. The following settings are included in user data.
Main Menu Menu configuration MAIN MARKER 16:9 MARKER VIDEO CONFIG SYSTEM CONFIG MARKER 4:3 GAMMA SELECT BACKLIGHT FILM GAMMA FUNCTION1 COLOR TEMP.
Main Menu (continued) MARKER The underlined values are factory preset setting values. Sub menu MARKER 16:9*1*2 MARKER 4:3*1*3 Settings <4:3 > <13:9> <14:9> <95%> <93%> <90%> <88%> <80%> <95%> <93%> <90%> <88%> <80%> Explanation Used to select/display the type of marker when the aspect ratio setting is 16:9. <4:3> <14:9> <93%> <88%> Marker not displayed.
Main Menu (continued) Types of MARKER g 16:9 marker (Displayed when using HD, or when using SD with a 16:9 aspect ratio) The marker is only displayed as a vertical bar. In addition, the section becomes the “MARKER BACK” item. 4:3 marker Area marker A dotted line is displayed as the marker. 95% Area marker 93% Area marker 90% Area marker 88% Area marker 13:9 marker 14:9 marker VISTA marker, CNSCO marker A horizontal dotted line is displayed as the marker.
Main Menu (continued) VIDEO CONFIG The underlined values are factory preset setting values. Sub menu GAMMA SELECT*2 Settings Explanation *1 Used to select the gamma curve. When FILM is selected, left of the screen. FILM GAMMA*2 Used to select the type of FILM gamma mode. VARICAM use When using other types than VARICAM COLOR TEMP. *5 Used to select the color temperature.
Main Menu (continued) g WB adjustment mode You can adjust “WHITE BALANCE VAR1” – “WHITE BALANCE VAR3” (WB) by selecting “VAR1” – “VAR3” in “COLOR TEMP.” in the “VIDEO CONFIG” menu. The underlined values are factory preset setting values. Sub menu COLOR TEMP. Settings WB-HIGH RED WB-HIGH GREEN Explanation Used to select the color temperature that will become the basis for adjustments.
Main Menu (continued) SYSTEM CONFIG The underlined values are factory preset setting values. Sub menu SUB WINDOW Settings Explanation Used to select the type of sub window. Used to reduce the whole input signal screen, and arrange it horizontally when it is displayed. Used to cut out the central section of the input signal screen, and arrange it horizontally when it is displayed (Displayed at the same size as the previous screen).
Main Menu (continued) g About the SUB WINDOW You can compare saved still and moving images or show the Wave Form Monitor (WFM) by using the “SUB WINDOW” function to separate the main window into 2 displays as shown below. Depending on the settings of the “SUB WINDOW” (FULL, PART, WFM) in the “SYSTEM CONFIG” menu (J page 18) it can be switched as shown below.
Main Menu (continued) GPI The “GPI CONTROL” item is used to set enable/disable of all GPI functions, and assigns functions to each of the GPI terminal pins (J page 23). The underlined values are factory preset setting values. Sub menu GPI CONTROL GPI1–GPI8 Settings Explanation GPI functions enable/disenable settings
Main Menu (continued) INPUT SELECT The underlined values are factory preset setting values. Sub menu VIDEO / Y/C Settings Explanation Used to select the input format for VIDEO and Y/C input. *1 Either NTSC or PAL is automatically selected. NTSC PAL NTSC SETUP <75> <00> Selects the NTSC setup level. <75> Select this when using with a setup signal of 7.5 IRE. (The inner parts of the monitor are set to the 7.
Main Menu (continued) g “PHASE” and “CLOCK” factory preset setting values FORMAT CLOCK PHASE FORMAT CLOCK PHASE 640x400(70Hz) 800 18 1024x768(60Hz) 1344 2 640x480(60Hz) 800 17 1024x768(70Hz) 1328 22 640x480(75Hz) 840 10 1024x768(75Hz) 1312 16 640x480(85Hz) 832 5 1024x768(85Hz) 1376 17 800x600(60Hz) 1056 31 1280x768(60Hz) 1728 8 800x600(75Hz) 1056 12 1280x768(75Hz) 1712 31 800x600(85Hz) 1048 29 1280x1024(60Hz) 1688 20 AUDIO Adjusting the speaker output.
