Data Sheet

ManualsBrandsPANASONIC ManualsSolid State RelaysAQA211VL

ASCTB21E 202101

Panasonic Corporation 2021

FEATURES



























TYPICAL APPLICATIONS

 









Load current 15 to 40 A Small Screw Terminal SSR

AQ-A

RELAYS ( AC output type )

Solid State Relays

25.5

(Unit: mm)

ORDERING INFORMATION ( PART NO. )

 

     





 







 

 



Output current

2: 15A

4: 25A

6: 40A

AQA

Control voltage

1: 4 to 32 V DC

Functions

VL: Built-in varistor and LED indication

Load voltage, Type

1: 75 to 250 Vrms, Screw terminal, Zero-cross

2: 75 to 250 Vrms, Screw terminal, Random*

* Random type is available by custom order.

TYPES

industrial.panasonic.com/ac/e/

2021.01

ー 1 ー

Summary of content (18 pages)

PAGE 1
Solid State Relays AQ-A RELAYS ( AC output type ) Load current 15 to 40 A Small Screw Terminal SSR FEATURES ●●Compact size: W 40 × L 58 × H 25.5 mm ●●W ith terminal cover for safety ( output side only ) Note: Cover on input side available as option. ●●Mounting pitch: 47.5 mm 40 58 ●●B uilt in varistor for excellent surge absorption 25.
PAGE 2
Solid State Relays AQ-A RELAYS ( AC output type ) ■■OPTION Type Part No. Standard Packing Carton Case 5 pcs. 20 pcs. 20 pcs. Standard heat sink ( 15 A ) AQP813 Standard heat sink ( 25 A ) AQP814 5 pcs. Standard heat sink ( 40 A ) AQP815 No carton Slim heat sink ( 45 mm wide ) ( Mountable on a DIN rail ) AQP812 No carton 8 pcs. DIN rail mounting plate AQP809 No carton 50 pcs. Terminal cover AQA801 No carton Mounting rail ATA48011 1 pcs. 100 pcs. ATA4806 1 pcs. 200 pcs.
PAGE 3
Solid State Relays AQ-A RELAYS ( AC output type ) REFERENCE DATA 1. L oad current vs. ambient temperature characteristics Use load current within range specified in the figure below. Tested condition: With external heat sink When using standard heat sink (AQP815, AQP814, AQP813, AQP812) 1) If attached to a heat sink, use a heat conductive compound (Ex. Momentive Performance Materials Inc. YG6111 or TSK5303) of similar coating to improve cooling.
PAGE 4
Solid State Relays AQ-A RELAYS ( AC output type ) OPTION Unit: mm ■■Slim heat sink ( AQP812 ) Mounting hole pattern External dimensions CAD 100 6 2-4.6 dia. or M4 90 78 7-Ｍ４ 40 90 ±0.2 6 30 (Effective screw depth: 6 mm) 4.6 dia. 4.6×5.6 elliptical hole 30 47.6 78 1.6 83 45 “A” part Note: When using on a DIN rail, please install so that the “A” part is on top. General tolerance: ±1.0 ■■Standard heat sink ( AQP813 ) Mounting hole pattern External dimensions CAD 50 4-M4 or 4.4 dia. 4.
PAGE 5
Solid State Relays AQ-A RELAYS ( AC output type ) ■■Standard heat sink ( AQP814 ) CAD Mounting hole pattern External dimensions 4-M4 or 4.4 dia. 50 4.4 2 R 2.2 100 ＋－0.5 1.5 11.1 2 1.5 47.6 33.3 80 54 90 3-M4 90 ±0.1 4.4 150 50 ±0.2 1.5 24.5 28.5 56 9 45 General tolerance: ±1.0 ■■Standard heat sink ( AQP815 ) CAD Mounting hole pattern External dimensions 4-M4.5 or 5 dia. 4-R2.5 119 ±0.1 150 119 47.5 30 5 3-M4 132 ±0.
PAGE 6
Solid State Relays AQ-A RELAYS ( AC output type ) ■■DIN rail mounting plate ( AQP809 ) CAD External dimensions 1.6 4.6 dia. 19 100 90 47.6 30 3-M4 12.1 16.5 4.6×5.6 elliptical hole 6 15 General tolerance: ±1.0 ■■Fastening plate ( ATA4806 ) ■■Terminal cover ( AQA801 ) CAD External dimensions CAD External dimensions 10 15 5 27 1.5 10.5 7 2 2.75R 15 10 15 24 35 10 M4 12 40-5.5×15 slot 5 15 25.25 50 12 5.
PAGE 7
Solid State Relays AQ-A RELAYS ( AC output type ) Recommended Temperature Controllers Space saving requiring only a depth of 56 mm ■■KT4H Temperature Controller • Data collection possible through a PLC using RS485 communication • Tool port is standard for easy data setting • Inverted LCD + backlight for good legibility with large characters • Excellent operability and rich optional control functions 48 mm [Substitute part numbers] 56 mm 48 mm Power supply Control output Part No.
PAGE 8
Cautions for Use of Solid State Relays SAFETY WARNINGS o not use the product under conditions that exceed the range of D its specifications. It may cause overheating, smoke, or fire. Do not touch the recharging unit while the power is on. There is a danger of electrical shock. Be sure to turn off the power when performing mounting, maintenance, or repair operations on the relay (including connecting parts such as the terminal board and socket).
PAGE 9
Cautions for Use of Solid State Relays Noise and surge protection at the output side 1) Phototriac coupler and AQ-H The figure below shows an ordinary triac drive circuit. Please add a snubber circuit or varistor, as noise/surge on the load side could damage the unit or cause malfunctions. Typical circuits are shown below.
PAGE 10
Cautions for Use of Solid State Relays Soldering Transportation and storage 1) When soldering surface-mount terminals, the following conditions are recommended. (1) IR (Infrared reflow) soldering method (Recommended condition reflow: Max.
PAGE 11
Cautions for Use of Solid State Relays The following shows the packaging format 1) Tape and reel (Phototriac coupler) Tape dimensions (Unit: mm) 1.75±0.1 Device mounted on tape 1.55±0.1dia. 4±0.1 2±0.1 2.8±0.3 12±0.1 2±0.5 80 ±1 dia. 5.5±0.1 7.2±0.1 (1) When picked from 1/2-pin side: Part No. APT****SX (Shown above) (2) When picked from 3/4-pin side: Part No. APT****SZ *Quality of material: Paper 14±1.5 13 ±0.5dia. 250 ±2dia. SO package 4-pin type 1.55±0.05dia. 21±0.8 80 ±1dia. 12±0.3 0.
PAGE 12
Cautions for Use of Solid State Relays 2) Tape and reel (AQ-H) Tape dimensions (Unit: mm) Dimensions of paper tape reel (Unit: mm) 80±1dia. 1.55 ±0.1dia. 2 ±0.1 (1) When picked from 1/2/3/4-pin side: Part No. AQH****AX (Shown above) (2) When picked from 5/6/8-pin side: Part No. AQH****AZ *Quality of material: Paper 13 ±0.5dia. 17.5±2 300±2dia. 12 ±0.1 2±0.5 ±0.3 10.1±0.1 Device mounted on tape 4.5 ±0.3 21±0.8 80 ±1dia. 16 8-pin SMD type 4 10.2 ±0.1 0.3 ±0.05 ±0.1 1.75 ±0.
PAGE 13
Cautions for Use of Solid State Relays Snubber Circuit Reduce dv/dt If there is no resistance R (the resistance R controls the discharge current from condenser C), at turn-on of the SSR, there will be a sharp rise in dv/dt and the high peak value discharge current will begin to flow. This may cause damage to the internal elements of the SSR. Therefore, it is always necessary to insert a resistance R.
PAGE 14
Cautions for Use of Solid State Relays Protection Circuit 2) Suppress transient spikes Use a switching device in the secondary circuit of a transformer or use a switch with a slow opening speed. 3) Use a surge absorption circuit Use a CR surge absorber or varistor across the load power supply or SSR. Special care must be taken so power on/off surges or external surges do not exceed the device’s rated load voltage.
PAGE 15
Cautions for Use of Solid State Relays Load Type Description Heaters (Resistive load) Solenoids The SSR is best suited to resistive loads. Noise levels can be drastically lowered with zero-crossing switching. Lamps Tungsten or halogen lamps draw a high inrush current when turned on (approximately 7 to 8 times the steady state current for zerocrossing SSRs; approximately 9 to 12 times, in the worst case, for random type SSRs).
PAGE 16
Cautions for Use of Solid State Relays Load Inrush Current Wave and Time (1) Incandescent Lamp Load (2) Mercury Lamp Load i/i0≒3 times (3) Fluorescent Lamp Load i/i0≒5 to 10 times Contacts io i L io i C io i (for high power factor type) Incandescent lamp Approx. 1/3 second Inrush current/rated current: i/i0≒10 to 15 times The discharge tube, transformer, choke coil, capacitor, etc., are combined in common discharge lamp circuits.
PAGE 17
Cautions for Use of Solid State Relays SSR Driving Circuits NPN Transistor Driver Load Load power supply Load power supply Load 1 2 PNP Transistor Driver 1 2 +Vcc 3 + 4 − Relay contacts 1 2 SSR SSR SSR +Vcc Load Load power supply Relay Driver 3 + 4 − +Vcc 4 − C-MOS/IC Driver Load Load Load power supply 1 1 2 2 3 + 4 − Load 1 SSR SSR +Vcc (2) SSR fires when IC output is LOW: Load power supply (1) SSR fires when IC output is HIGH: Load power supply + PNP Transistor
PAGE 18
Please contact .......... Electromechanical Control Business Division 1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan industral.panasonic.com/ac/e/ ©Panasonic Corporation 2021 ASCTB21E 202101 Specifications are subject to change without notice.