Panasonic Broadcast AK-HC910 Menu Information
Setting of Menu Items _ Configuration of menu display screen USER MENU 1.MAINTENANCE 2.SETTING 3.CAM ID 4.FILE MENU Maintenance menu ° MAINTENANCE ° 1.BLACK SHADING 2.PED,GAMMA,FLARE 3.KNEE,WHITE CLIP 4.R/B GAIN 5.DTL 6.GAIN,AUTO IRIS 7.S.GAIN 1 8.S.GAIN 2 9.S.GAIN 3 10.MATRIX 11.COLOR CORRECTION1 12.COLOR CORRECTION2 USER MENU Using condition setting menu °° SETTING°° 1.MODE 2.SHUTTER 3.H.
Setting of Menu Items _ USER menu (Initial screen) The readout data at start of power supply is the data just before cutting off the power supply, and the operation is started with the data. USER MENU 1.MAINTENANCE 2.SETTING 3.CAM ID 4.FILE MENU 1. MAINTENANCE It sets various adjusting data. 2. SETTING It sets various modes. 3. CAM ID It sets the camera ID. 4. FILE MENU It executes file loading and saving, and makes the basic setting of data display.
Setting of Menu Items ! Maintenance menu • Move the cursor (arrow mark) to the item to be adjusted and press the MENU key, then it enters the adjustment menu thereunder. °MAINTENANCE° 1.BLACK SHADING 2.PED,GAMMA,FLARE 3.KNEE,WHITE CLIP 4.R/B GAIN 5.DTL 6.GAIN,AUTO IRIS 7.S.GAIN 1 8.S.GAIN 2 9.S.GAIN 3 10.MATRIX 11.COLOR CORRECTION1 12.COLOR CORRECTION2 • Move the cursor to MAINTENANCE and press the MENU key, then it returns to USER MENU.
Setting of Menu Items ! Maintenance menu 2 Pedestal, gamma, flare adjustment menu °° PED,GAMMA,FLARE°° M PED R PED B PED M GAMMA R GAMMA B GAMMA R FLARE G FLARE B FLARE GAMMA FLARE :+027 :+000 :+000 :0.45 :+00 :+00 :010 :000 :017 :ON :ON M PED: Master pedestal can be adjusted only by turning the control panel VR. The R, G, B pedestal can be totally adjusted. R, B PED: R, B pedestal adjustment. Besides the master pedestal adjustment, R, B pedestal can be independently adjusted.
Setting of Menu Items ! Maintenance menu °° KNEE,WHITE CLIP M KNEE POINT R KNEE POINT B KNEE POINT M KNEE SLOPE R KNEE SLOPE B KNEE SLOPE A.KNEE POINT A.KNEE LVL WHITE CLIP LVL KNEE WHITE CLIP 3 Knee&white clip adjustment menu °° M KNEE POINT: Master knee point adjustment. G, B, R knee point can be totally adjusted. :95.00% :+00.00% :+00.00% :95.00% :+000 :+000 :95.00% :108 :109% :MANU :ON R, B KNEE POINT: R, B knee point adjustment.
Setting of Menu Items ! Maintenance menu °° R/B GAIN 4 Gain adjustment menu °° R GAIN B GAIN The gain of R, B GAIN is adjusted. The difference from the state of being white-balanced can be adjusted. :+000 :+000 • The numeral value displayed after normal ending of AWB is “0” for both of R, B. 5 Detail adjustment menu °° DTL °° DTL TOTAL DTL LVL H DTL LVL CRISP LVL DEPENDENT PEEK FREQUENCY KNEE APERTURE KNEE APA.
Setting of Menu Items ! Maintenance menu 5 Detail adjustment menu (continued from previous page) °° DTL °° DTL TOTAL DTL LVL H DTL LVL CRISP LVL DEPENDENT PEEK FREQUENCY KNEE APERTURE KNEE APA.LVL SLIM DTL DTL(+) DTL(-) DTL CLIP DTL SOURCE °° GAIN,AUTO IRIS :ON :+00 :11 :02 :2 :10 :ON :10 :OFF :+00 :+00 :0 :(B+G)/2 DTL (+): Setting of DTL at the edge in positive direction. DTL (–): Setting of DTL at the edge in negative direction. DTL CLIP: Setting of clip level of DTL edge.
Setting of Menu Items ! Maintenance menu °° S GAIN 1°° GAIN ° TOTAL ANLG GAIN PIX MIX H DTL LVL CRISP LEVEL DEPENDENT PEAK FREQUENCY M GAMMA MASTER PED OFFSET R PED OFFSET B PED OFFSET 7 Super gain, Detail, Pedestal-offset level setting menu TOTAL GAIN: Total gain in analog, pixel addition, and memory addition is displayed. ANLG GAIN: Gain setting in analog. PIX MIX: Gain setting in horizontal pixel addition. Capable of setting 0/6 dB. H DTL LVL: DTL level setting of super gain.
Setting of Menu Items ! Maintenance menu 8 Matrix menu Selection of table A, B or OFF. Adjustment of gain of each color. < MATRIX > MATRIX MATRIX MATRIX MATRIX MATRIX MATRIX MATRIX TABLE R-G R-B G-R G-B B-R B-G :A :+00 :+00 :+00 :+00 :+00 :+00 9 Color correction 1 menu < COLOR CORRECTION1 > SAT PHASE R +00 +00 Mg +00 +00 B +00 +00 Cy +00 +00 G +00 +00 Y1 +00 +00 Adjustment of gain (saturation) and phase of each color.
Setting of Menu Items @ Setting menu - Menu for various settings. °° SETTING°° 1.MODE 2.SHUTTER 3.H.PHASE 1 Camera mode setting menu °° MODE°° BLACK STRETCH D5600K CABLE COMPE SUP GAIN CAM ID CAM ID POSI MATRIX TABLE COLOR CORRECTION STATUS BLACK STRETCH: Setting of the function of expanding low-brightness analog video level. It is set by ON/OFF.
Setting of Menu Items @ Setting menu 1 Camera mode setting menu (continued from previous page) °° MODE°° BLACK STRETCH D5600K CABLE COMPE SUP GAIN CAM ID CAM ID POSI MATRIX TABLE COLOR CORRECTION STATUS :OFF :OFF :0m :OFF :BAR :0 :OFF :OFF :ON CAM ID POSI: It sets the display position of camera ID. 0: top left, 1: top right, 2: down left, 3: down right. MATRIX TABLE: It sets A, B or OFF of Matrix table. COLOR CORRECTION: Setting of matrix ON/OFF.
Setting of Menu Items # Camera ID setting menu °°CAM ID °° ID:AKHC900 $ File managing and renewing menu - File operation menu H FILE MENU ° ° FILE SAVE FILE? SAVE : blinking display. :USER1 :USER1 : 1 The file selected by FILE is loaded. It can be selected from [PRESET/USER1 / USER2 /CURRENT]. When desired to return to the previous data after loading other file, select “CURRENT”.
Setting of Menu Items $ File managing and renewing menu - File operation menu (continued from previous page) H FILE MENU ° FILE SAVE FILE? SAVE :USER1 :USER1 : 2 When saving the current data, two files (USER1 /USER2) can be saved. Select the file by “SAVE FILE?” Select “USER1” and move the cursor to SAVE and press the MENU key, then the item menu is displayed. 3 SAVE IN USER1. OK? “YES” and “NO” are displayed. Move the cursor from “NO” to “YES” and check that “YES” blinks.
