Panasonic Broadcast AJ-SD965 Menu Information
Setup (initial settings) This VTR’s main settings are performed while making selections using a system of menus. FF button button. The settings on the menu screen and display now flash. When the dial is turned clockwise, the setting number is incremented; conversely, when it is turned counterclockwise, it is decremented. O At this time, when the RESET button is pressed while holding down the search button, the setting value is returned to the factory setting.
Setup menus This VTR can hold five user files, each of which has its own specific menu settings, and one of these files can be selected for use. Changing the file 1 Press the MENU (SHIFT+RECORDER). the FF button is pressed while holding down 2 When the SHIFT button, the next user file is selected; conversely, when the REW button is pressed while holding down the SHIFT button, the previous user file is selected.
Setup menus (continued) Loading user files The contents of the USER2, USER3, USER4 or USER5 file can be copied (loaded) into the USER1 file. Also, the contents of the USER1 file can be copied (saved) into the USER2, USER3, USER4 or USER5 file. Load/save USER 1 USER 2 Lock mode can be set USER 3 Lock mode can be set USER 4 Lock mode can be set USER 5 Lock mode can be set Load/save Load/save Load/save 1 Press the MENU the SET button.
Setup menus (continued) Saving user files 1 Press the MENU the PLAY button. 6 Press The settings of USER1 are saved in the user file (SHIFT+RECORDER). the REW button or FF button while holding 2 Press down the SHIFT button to select the USER1 file. the search dial to move the cursor (2) on the 3 Turn menu screen to No. A01 (SAVE). SETUP-MENU MENU NO.A00-0000 804 BLANK LINE BLANK A00 LOAD USER2 USER2 2A01 SAVE A02 P.ON LOAD OFF END selected in step 4 and stored in the memory.
Setup menus (continued) SYSTEM menu No./Item 00 Description This selects the signal to output from the VIDEO OUT 2 connector. WFM SEL No./Item 14 SCH COARSE 0000 0001 CTL : The CTL signal is output. TC : The TIME CODE signal is output. 0002 VIDEO : The VIDEO OUT signal is output. 0003 RF_L : The PB L RF signal is output. 0004 RF_R : The PB R RF signal is output. 0005 ENV_L : The PB L ENV signal is output. 0006 ENV_R : The PB R ENV signal is output.
Setup menus (continued) SYSTEM menu No./Item Description No./Item 18 System phase adjustment. 30 SYS H OFFSET 0000 –3 : –13.4 µsec 0001 –2 : –8.96 µsec 0002 –1 : –4.52 µsec 0003 0 : 0 sec 0004 1 : +4.52 µsec 0005 2 : +8.96 µsec 0006 3 : +13.4 µsec Factory settings will remain unchanged even if an attempt is BRIGHT 19 SYS SC/H This sets whether the system phase is to be adjusted by the unit or from the external encoder remote controller.
Setup menus (continued) USER menu No./Item 000 P-ROLL TIME This sets the preroll time. The preroll time can be set from 0 to 15 seconds in 1-second increments. 0000 : 0005 : 0015 001 LOCAL ENA No./Item Description 0s : 5s : 15s When the automatic mode [PREVIEW, EDIT] is set, the unit operate if the preroll set to 0 seconds. This selects the buttons on the front panel which can be operated when the REMOTE button is set to the remote mode (REMOTE lamp ON).
Setup menus (continued) USER menu No./Item 009 CHARA H-POS This sets the position of the characters on the horizontal plane for the time code and other super displays output to the VIDEO OUT 3/SDI OUT 3 connector. 0000 : 0004 : 0016 010 CHARA V-POS CHARA TYPE 0001 This sets the VTR’s recording and playback format. This sets the format in which the tape is to be played back. 0000 MANUAL : The format complies with the setting of setup menu No.
Setup menus (continued) USER menu No./Item 100 SEARCH ENA 101 Description This selects the direct search dial operation. 0000 DIAL : For direct search dial operations. 0001 KEY : Operation is not transferred to the search mode unless the search button is pressed. No./Item 105 AUTO EE SEL SHTL MAX 102 a8.4 : 8.4a normal speed a16 : 16a normal speed a32 : 32a normal speed This sets the maximum speed for FF and REW operations. FF.
Setup menus (continued) USER menu No./Item 109 AUTO REW This selects whether to rewind the tape automatically to the tape start when the tape end is detected. 0000 0001 110 No./Item Description 111 FRZ MODE SEL OFF : The tape stops at the tape end. ON : The tape is rewound to the tape start. 0000 OFF : The VTR does not stop. 0001 ON : The VTR stops automatically.
Setup menus (continued) USER menu No./Item Description 114 This selects whether to cause the REC INH lamp to flash or light up when the cassette REC INH LAMP has been set to the accidental erasure prevention status. 0000 LIGHT : The lamp lights up. 0001 FLASH : The lamp flashes. When the REC INH switch is set to ON, the REC INH lamp always lights regardless of the general setting status.
Setup menus (continued) USER menu No./Item 200 No./Item Description This selects whether two or more VTRs are to be operated in synchronization. PARA RUN 208 9P SEL 0000 NON : Parity bit is not used. 0001 ODD: An odd number of bits is used for the parity system. 0002 EVEN: An even number of bits is used for the parity system. This selects whether the 9P connector is to function when the REMOTE button is set to the remote mode (REMOTE lamp ON).
Setup menus (continued) USER menu No./Item 301 IN/OUT DEL Description This selects the operation to be performed when an edit point has been set incorrectly (when the OUT point is before the IN point). No./Item 305 EDIT RPLCE1 0000 MANU : Editing is not executed unless the illegal edit point is cleared or set again properly. 0001 AUTO : The edit points already input are automatically cleared. 303 STD/ NON-STD 304 SERVO REF The underlined items indicates the initial setting.
Setup menus (continued) USER menu No./Item 308 EDIT RPLCE4 The same type of setting as setup menu No. 305. This selects the channel concerned when the CH4 edit preset is set in compliance with the ON or OFF presetting for the analog audio signals designated by the controller. 0000 N-DEF : Not set. 0001 CH1 : Compliance with analog CH1 edit preset. 0002 CH2 : Compliance with analog CH2 edit preset. 0003 CH1+2 : Compliance with analog CH1 or CH2 edit preset.
Setup menus (continued) USER menu No./Item No./Item Description 324 This sets the maximum JOG REV speed. JOG REV MAX 0000 –4.1 : –4.1 (–3.1)a speed 0001 –1.85 : –1.85a speed 0002 –1 : –1a speed 0003 –0.43 : –0.43 (–0.5)a speed OThe value for the DV/DVCAM tape is shown in parenthesis ( ). OThe maximum speed is set to –1a when the dial on the front panel is operated. 401 When the time selected as the setup menu item No.
Setup menus (continued) USER menu No./Item 500 VITC BLANK
Setup menus (continued) USER menu No./Item 511 VITC OUT
Setup menus (continued) USER menu
Setup menus (continued) USER menu No./Item 620 ESR MODE
Setup menus (continued) USER menu No./Item 623 SETUP 50
Setup menus (continued) USER menu No./Item 660
Setup menus (continued) USER menu
Setup menus (continued) USER menu
Setup menus (continued) USER menu
Setup menus (continued) USER menu No./Item 800 Description For selecting the mode for recording signals on additional lines. ADD LINE 25 0000 OFF : No signals are recorded on additional lines. 0001 YC422 : The 422 mode signals are recorded on 1 line. 0002 YC411 : The 411 mode signals are recorded on 1 line. 0003 Y1_B/W : Only the Y signal is recorded on 1 line directly. 0004 Y1_BPF : Only the Y signal is recorded on 1 line after it has been separated from the C signal.
Setup menus (continued) USER menu No./Item 801 Description For selecting the mode for recording signals on additional lines. ADD LINE 50 0000 OFF : No signals are recorded on additional lines. 0001 YC422 : The 422 mode signals are recorded on 2 lines. 0002 Y4_B/W : Only the Y signal is recorded on 4 lines directly. 0003 Y4_BPF : Only the Y signal is recorded on 4 lines after it has been separated from the C signal. 0004 C4 : Only the C signal is recorded on 4 lines.
Setup menus (continued) USER menu No./Item 803 TELETEXT DET Description For selecting the method used to detect the lines in which the teletext signals are to be recorded. 0000 OFF : The teletext signals are not recorded. 0001 AUTO : The teletext signals are automatically detected and recorded. 0002 MANU : The lines in which the teletext signals are to be recorded are selected and set.
Setup menus (continued) USER menu No./Item 900 Description No./Item This sets the LCD monitor’s saving function (see page 11). LCD PROTECT A02 P. ON LOAD 0000 OFF : The saving function is not established. 0001 ON : The saving function is established. 901 BL BRIGHT 0000 NORMAL : The backlight lights at the normal brightness. 0001 HIGH : The backlight lights more brightly than normal.
