AJ-HPX2000P(VQT1D27-1)E.book 1 ページ ２００７年７月３０日 月曜日 午後１時３１分 Operating Instructions Memory Card Camera-Recorder Model No. AJ-HPX2000P Before operating this product, please read the insructions carefully and save this manual for future use. To use AVC-Intra, the AVC-Intra codec board (AJ-YBX200G/optional) must be installed.
AJ-HPX2000P(VQT1D27-1)E.book 2 ページ ２００７年７月３０日 月曜日 午後１時３１分 Read this first! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
AJ-HPX2000P(VQT1D27-1)E.book 3 ページ ２００７年７月３０日 月曜日 午後１時３１分 Attention/Attentie ENGLISH z Batteries are used for the main power source and memory back-up in the product. At the end of their useful life, you should not throw them away. Instead, hand them in as small chemical waste. NERDERLAND z Voor de primaire voeding en het reservegeheugen van het apparaat wordt gebruikgemaakt van een batterij.
AJ-HPX2000P(VQT1D27-1)E.book 4 ページ ２００７年７月３０日 AJ-HPX2000P(English)TOC.fm 月曜日 午後１時３１分 master: left Contents Read this first! ..................................................................................2 General Features of Camera unit ....................................................................8 Features of Recorder/player unit .......................................................9 Features of the Input/Output unit .....................................................11 Other features .
AJ-HPX2000P(VQT1D27-1)E.book 5 ページ ２００７年７月３０日 AJ-HPX2000P(English)TOC.fm 月曜日 午後１時３１分 master: right Setting Time Data ...........................................................................55 Viewfinder Screen Status Displays ..................................................69 Adjusting and setting the LCD monitor ............................................80 Selection of video output signals .....................................................81 Handling data .....................................
AJ-HPX2000P(VQT1D27-1)E.book 6 ページ ２００７年７月３０日 AJ-HPX2000P(English)TOC.fm Maintenance and Inspections 月曜日 午後１時３１分 master: left Inspections Before Shooting ........................................................138 Maintenance.................................................................................140 Warning System...........................................................................145 Menu Menu Configuration......................................................................
AJ-HPX2000P(VQT1D27-1)E.book 7 ページ ２００７年７月３０日 月曜日 午後１時３１分 General Attention z Adjust the black-balance setting when using the unit for the first time. (Refer to page 48) z Set VF TYPE on the screen on the SYSTEM SETTING page depending on your viewfinder. The factory setting is set to the HD viewfinder. z Consult the dealer for installation of the AVC-Intra codec board (AJ-YBX200G).
AJ-HPX2000P(VQT1D27-1)E.book 8 ページ ２００７年７月３０日 月曜日 午後１時３１分 _ Multi-format Mode SYSTEM MODE Recording method AVC-Intra100*1 AVC-Intra50*1 1080-59.94i DVCPRO HD AVC-Intra100*1 AVC-Intra50*1 720-59.94P DVCPRO HD HD AVC-Intra100*1 1080-50i AVC-Intra50*1 DVCPRO HD AVC-Intra100*1 AVC-Intra50*1 720-50P DVCPRO HD 480-59.94i DVCPRO50 DVCPRO DV SD 576-50i DVCPRO50 DVCPRO DV 59.94i 29.97P (Native) 23.98P (Native) 59.94i 29.97P Over 59.94i 23.98P Over 59.94i (2-3 Pull-down) 23.98P Over 59.
AJ-HPX2000P(VQT1D27-1)E.book 9 ページ ２００７年７月３０日 月曜日 午後１時３１分 _ Data management function Within the unit, one user data file and four sets of scene file data can be saved. By using an SD memory card as the setup card, up to eight sets of setup data can be stored. (Refer to page 83) _ Color bar The unit employs the SMPTE color bar, ARIB color bar, Split color bar for SNG (Satellite News Gathering) as well as the conventional color bar, which is useful for adjusting the color monitor.
AJ-HPX2000P(VQT1D27-1)E.book 10 ページ ２００７年７月３０日 月曜日 午後１時３１分 _ Support for Metadata AJ-HPX2000 is capable of recording positional information (latitudes, longitudes and altitudes), as UMID information (metadata), from the GPS unit AJGPS910G (optional accessory). Names/titles can also be recorded, e.g. the camera person, the reporter, or the program which was registered on the SD memory card in advance. This information is also useful in managing information on clips.
AJ-HPX2000P(VQT1D27-1)E.book 11 ページ ２００７年７月３０日 月曜日 午後１時３１分 Features of the Input/Output unit _ Features USB2.0 port (HOST/DEVICE) _ DVCPRO (IEEE1394) output and DV output provided as a standard configuration Data can be input/output to an external device through the IEEE1394 digital interface. Use a 6-pin type connector. The unit does not support the bus power. While operating AVC-Intra, it is impossible to input/ output data with IEEE 1394.
AJ-HPX2000P(VQT1D27-1)E.book 12 ページ ２００７年７月３０日 月曜日 午後１時３１分 Dimensions drawing Unit: mm (inch) 137 (5- 3 / 8 ) 102 (4- 1 /16 ) 12 General：Dimensions drawing 270.
AJ-HPX2000P(VQT1D27-1)E.
AJ-HPX2000P(VQT1D27-1)E.book 14 ページ ２００７年７月３０日 月曜日 午後１時３１分 Parts and their Functions Power Supply and Accessory Mounting Section 5 11 7 6 6 2 9 8 10 1 4 3 15 1. POWER switch Used to turn on/off the power. 2. Battery mount A battery pack from Anton/Bauer is mounted here. 14 12 13 10. Lens mount cap To remove the cap, raise the 9. lens lever. When the lens is not mounted, replace the cap. 11. Light cable clamp Secures the light cable. 3.
AJ-HPX2000P(VQT1D27-1)E.book 15 ページ ２００７年７月３０日 月曜日 午後１時３１分 Audio (input) Function Section 12 13 11 14 10 3 7 Parts and their Functions 2 6 1 1. MIC IN (microphone input) jack (XLR, 5-pin) A microphone (optional accessory) is connected here. Power for the microphone comes from this jack. A remote microphone may be connected. When a microphone is used, set the power to ON through the menu option FRONT MIC POWER. These options are found in the screen on the MAIN OPERATION page. 2.
AJ-HPX2000P(VQT1D27-1)E.book 16 ページ ２００７年７月３０日 月曜日 午後１時３１分 Audio (output) Function Section 9. AUDIO OUT connector (XLR, 5-pin) This connector outputs audio signals recorded on Channels 1/2 or 3/4. Output signals are selected with the MONITOR SELECT CH1/2 / CH3/4 selector switch. 10. MONITOR SELECT (audio channel) CH1/2 / CH3/4 selector switch Use this switch to select the audio channel whose signals are output to the speakers, earphones or AUDIO OUT connector.
AJ-HPX2000P(VQT1D27-1)E.book 17 ページ ２００７年７月３０日 月曜日 午後１時３１分 Shooting and Recording/Playback Functions Section 10 9 8 34 24 25 20 21 22 23 36 35 15 27 2 28 29 3 11 17 33 4 6 14 12 5 13 16 19 Used to select a filter appropriate for illumination and color temperature of the subject. When the menu option DISP MODE is set to “3”, switching this control displays the selected filter number in the viewfinder.
AJ-HPX2000P(VQT1D27-1)E.book 18 ページ ２００７年７月３０日 月曜日 午後１時３１分 5. Gain selector switch Use this switch to select video amplifier gain, according to lighting conditions under which you are shooting. The values for L, M, and H can be preset using menu options. These are factory-set to 0 dB for L, 6 dB for M, and 12 dB for H. 6. OUTPUT/AUTO KNEE selector switch Used to select the video signals sent from the camera unit to the memory, viewfinder and video monitor. CAM.
AJ-HPX2000P(VQT1D27-1)E.book 19 ページ ２００７年７月３０日 月曜日 午後１時３１分 10 9 8 34 24 25 20 21 22 23 36 35 1 26 15 27 2 Parts and their Functions 28 29 3 11 17 33 4 6 14 12 5 13 16 19 32 18 31 30 7 14. SAVE ON/OFF switch 18. MON OUT (monitor output) connector Used to select the power supply method for each output section. ON: The output selected through the menu option SAVE SW is power-saved. This option can be found on the OPTION MODE screen on the SYSTEM SETTING page.
AJ-HPX2000P(VQT1D27-1)E.book 20 ページ ２００７年７月３０日 月曜日 午後１時３１分 20. REW (rewind) button and lamp During pause, this button performs a fast-reverse playback with the lamp blinking. During playback, it performs an approximately 4a fastreverse playback with the PLAY and REW lamps blinking. If this button is pressed when playback is paused, the start of the clip being played back is located in pause mode. 21. STOP button This button stops playback. 22.
AJ-HPX2000P(VQT1D27-1)E.book 21 ページ ２００７年７月３０日 月曜日 午後１時３１分 32. DVCPRO/DV connector 35. SD memory card insertion slot This is an in/output connector for video, voice, and data that comply with the IEEE1394 standard. Notes 33. REMOTE (remote control) connector The remote control unit AJ-RC10G accessory) is connected here. (optional 34. OPTION SLOT Attach the video encoder card (AJ-YAX800G, optional). For information about the installation and proxy recording, see the AJ-YAX800G instruction manual.
AJ-HPX2000P(VQT1D27-1)E.book 22 ページ ２００７年７月３０日 月曜日 午後１時３１分 Menu Operation Section 1. MENU button Used to turn on/off the menu. 2. JOG dial button 4 3 With the menu open, this button is used to navigate through menu pages, select options and specify values. For directions on manipulating the menu, see [Menu Configuration] (page 151). 3. SD memory card insertion slot 5 2 An SD memory card (optional accessory) is inserted here.
AJ-HPX2000P(VQT1D27-1)E.book 23 ページ ２００７年７月３０日 月曜日 午後１時３１分 Time Code Section 4 5 6 Parts and their Functions 7 1 3 2 1. GENLOCK IN connector (BNC) This connector is used to input a reference signal before the camera unit is gen-locked, or before the time code is externally locked. 2. TC IN connector (BNC) This connector is used to input a reference time code when you externally lock the time code. 3.
AJ-HPX2000P(VQT1D27-1)E.book 24 ページ ２００７年７月３０日 月曜日 午後１時３１分 Warning and Status Display Functions 7. Display window 1 2 6 7 3 4 5 This window displays warnings, battery-remaining level, sound volume, time data, and other information. Note When the battery is installed, the camera-recorder indicates the data even if the power is turned off. To turn off the data indications to keep the battery from being discharged, specify OFF for the menu option P.
AJ-HPX2000P(VQT1D27-1)E.
AJ-HPX2000P(VQT1D27-1)E.book 26 ページ ２００７年７月３０日 月曜日 午後１時３１分 Positions of time code-related switches and information provided Position of DISPLAY switch Position of TCG switch Information Item SET Time code F-RUN or R-RUN CTL CTL TC Time code F-RUN/SET/ R-RUN UB User bits or realtime, time zone LCD Monitor 5. CURSOR and SET buttons The four triangular buttons are the CURSOR buttons, and the center rectangular one is the SET button.
AJ-HPX2000P(VQT1D27-1)E.book 27 ページ ２００７年７月３０日 月曜日 午後１時３１分 Viewfinder You can use any of the following viewfinders (extra-cost options) on AJ-HPX2000: HD Viewfinders: AJ-HVF21G (selectable between 59.94 and 50 Hz) SD Viewfinders: AJ-VF20WBP (59.94 Hz), AJ-VF15BP (59.
AJ-HPX2000P(VQT1D27-1)E.book 28 ページ 13 ２００７年７月３０日 14 11 7 月曜日 午後１時３１分 9 9. Eyepiece 10 Note 12 Do not leave the eyepiece aimed at the sun. Doing so may damage the internal components. 1 10. Diopter adjustment ring 8 4 5 2 3 6 1. Viewfinder (optional accessory) During recording or playback, the viewfinder displays the video image in monochrome. It also displays warnings, messages, zebra patterns, markers (safety zone and center markers), etc. 2.
AJ-HPX2000P(VQT1D27-1)E.book 29 ページ ２００７年７月３０日 月曜日 午後１時３１分 Recording and Playback P2 Cards 3 Inserting P2 Cards Insert a P2 card into the P2 card slot until the EJECT button pops up. Note 1 Recording and Playback When using the camera-recorder for the first time, be sure to set the time data beforehand. On how the time data is set, see [Setting Time Data] (page 55). EJECT button Turn on the POWER switch. The card must be inserted with the logo right way up.
AJ-HPX2000P(VQT1D27-1)E.book 30 ページ ２００７年７月３０日 月曜日 午後１時３１分 Removing P2 Cards 1 2 3 While pressing down the slide lock button, move the slide-out door to the left. The door opens. Tilt down the EJECT button. Then, depress the EJECT button to release the P2 card so that you can remove it. The P2 CARD ACCESS LEDs may be set to stay off using the menu option ACCESS LED. This option can be found on the
AJ-HPX2000P(VQT1D27-1)E.book 31 ページ ２００７年７月３０日 月曜日 午後１時３１分 How to handle data recorded on P2 cards The P2 card is a semiconductor memory card that is used as the recording medium in the professional video production and broadcasting devices that make up the DVCPRO P2 Series. z Since data recorded in the DVCPRO P2 format or AVCIntra (option) are in a file format, they have excellent compatibility with PCs.
AJ-HPX2000P(VQT1D27-1)E.book 32 ページ ２００７年７月３０日 月曜日 午後１時３１分 Basic Procedures This section describes the basic procedure for shooting and recording. Before you embark on a shoot, pre-inspect your system to ensure that it works properly. Note that the recording order is retained even if the power is turned off. When the power is next turned on, the last card written before powering-down will be the target card.
AJ-HPX2000P(VQT1D27-1)E.book 33 ページ ２００７年７月３０日 月曜日 午後１時３１分 Shooting White/Black balance adjustment to recording completion White/Black Balance Adjustment to Recording Completion For shooting, follow the steps below. 1 Select a filter according to light conditions. 2A When the white balance is saved: Position the WHITE BAL switch to [A] or [B]. you have no time to adjust the white balance: Position the WHITE BAL switch to [PRST].
AJ-HPX2000P(VQT1D27-1)E.book 34 ページ ２００７年７月３０日 月曜日 午後１時３１分 Normal Recording REC START/STOP button, REC button on the handle or VTR button at the lens starts recording of video and sound on the P2 card. A cluster of data that consists of video and sound generated through a shooting action, together with such added information as meta data, is called a “clip”.
AJ-HPX2000P(VQT1D27-1)E.book 35 ページ ２００７年７月３０日 月曜日 午後１時３１分 Notes REC START/STOP button Mode check button Recording and Playback z The recording will start from the top frame of a five-frame cycle for 24P/24PA recording, a four-frame cycle for 24P native recording or a two-frame cycle for 30P and 25P of 720P, respectively. Therefore, the time code may be discontinued when recording clips continuously in different modes during the recording cycle.
AJ-HPX2000P(VQT1D27-1)E.book 36 ページ ２００７年７月３０日 月曜日 午後１時３１分 Loop Recording When two or more P2 card slots contain cards, this function allows the target P2 card to be switched in order. Even when the free space of a P2 card is used up, this function continues recording while erasing existing data. To use this function, the menu option LOOP REC MODE must be set to “ON” The option LOOP REC MODE can be found in the screen on the SYSTEM SETTING page.
AJ-HPX2000P(VQT1D27-1)E.book 37 ページ 1 2 3 ２００７年７月３０日 月曜日 午後１時３１分 Shooting procedures when INTERVAL REC is ON Shooting procedures for the ONE SHOT mode of INTERVAL REC Following basic operations of shooting and recording according to “Basic Procedures”, lock the camera securely. After setting the INTERVAL REC mode, follow these steps: Check that “i” is blinking in the display, and that the interval recording mode is selected.
AJ-HPX2000P(VQT1D27-1)E.book 38 ページ ２００７年７月３０日 月曜日 午後１時３１分 During INTERVAL REC mode general notes z Sound By selecting ON/OFF for the menu option AUDIO REC in the REC FUNCTION screen, it is possible to specify whether or not sound will be recorded during interval recording. z Record/Playback Buttons During interval recording, all operation buttons other than STOP (REW, FF, PLAY/PAUSE) are disabled. However, during a pause in ONE SHOT mode, REC REVIEW can be executed with the RET button on the lens.
AJ-HPX2000P(VQT1D27-1)E.book 39 ページ ２００７年７月３０日 月曜日 午後１時３１分 Recording Review Function Recording starts Recording and Playback When recording is paused, pressing the RET button automatically locates the last two seconds of video just recorded, and the viewfinder provides video playback. After playback, the camera-recorder is again ready to start recording. The picture location/playback duration can be increased to up to 10 seconds by continuously pressing the RET button.
AJ-HPX2000P(VQT1D27-1)E.book 40 ページ ２００７年７月３０日 月曜日 午後１時３１分 Normal and Variable Speed Playback The PLAY/PAUSE button provides monochrome playback through the viewfinder and color playback on the LCD monitor. A color video monitor connected to the VIDEO OUT or MON OUT connector of camera-recorder also provides color playback. The VIDEO OUT connector outputs an SDI playback (to view the playback, the OUTPUT SEL switch on the side panel must be positioned to [MEM]).
AJ-HPX2000P(VQT1D27-1)E.book 41 ページ ２００７年７月３０日 月曜日 午後１時３１分 Shot Mark Function A shot mark is added to the thumbnail of a clip to distinguish that clip from others. With the LCD monitor, only clips that have shot marks can be viewed and/or played back. Adding Shot Marks Notes z When the color bar is output or the unit is in LOOP REC mode and INTERVAL REC mode, it is impossible to add/ delete shot marks. z It is impossible to add shot marks to incomplete clips (refer page 111).
AJ-HPX2000P(VQT1D27-1)E.book 42 ページ ２００７年７月３０日 月曜日 午後１時３１分 Adjustments and Settings for Recording Multi Format Video system and Recording format The unit employs a progressive scan (full pixel reading) CCD system. With combinations of the SYSTEM MODE and CAMERA MODE menu options on the SYSTEM MODE screen on the SYSTEM SETTING menu, you can select an image system from among 23 types*1 including HD (1080i, 720P) and SD formats.
AJ-HPX2000P(VQT1D27-1)E.book 43 ページ ２００７年７月３０日 月曜日 午後１時３１分 Recording formats and output connector signal formats The table below shows the formats used to record signals from the CCD and externally input signals along with the formats for signals output from the output connectors. For 59.94 Hz Menu setting Recording Output VIDEO OUT SYSTEM MODE item REC MODE item REC SIGNAL item P2 card CAMERA Recording Output 1 recording* MODE frame frame item mode mode Video Sound DVCPROHD 108059.
AJ-HPX2000P(VQT1D27-1)E.
AJ-HPX2000P(VQT1D27-1)E.book 45 ページ ２００７年７月３０日 月曜日 午後１時３１分 Adjusting the White balance and Black Balance To record high-quality video with the unit, the black and white balances must be adjusted according to conditions. For higher quality, it is recommended that the adjustments should be made in this order AWB (white balance adjustment) > ABB (black balance adjustment) > AWB (white balance adjustment). Adjusting the White Balance Whenever light conditions change, the white balance must be re-adjusted.
AJ-HPX2000P(VQT1D27-1)E.book 46 ページ ２００７年７月３０日 月曜日 午後１時３１分 Detection area for the white balance Retaining white balances The detection area for the white balance is selectable between 90%, 50% and 25%, using the menu option AWB AREA. This option can be found in the screen, which is accessible from the CAM OPERATION page. The detection area is factory-set to 25%. 90% 50% 25% When you have no time to adjust the white balance Position the WHITE BAL switch at [PRST].
AJ-HPX2000P(VQT1D27-1)E.book 47 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting Color Temperature Manually The white balance can be manually adjusted by setting the color temperature. Manual color temperature settings can be performed for each of the WHITE BAL switch positions: PRST, A and B. The color temperature is set using the menu options COLOR TEMP PRE, COLOR TEMP A, and COLOR TEMP B. These options can be found in the screen, which is accessible from the CAM OPERATION page.
AJ-HPX2000P(VQT1D27-1)E.book 48 ページ ２００７年７月３０日 月曜日 午後１時３１分 Adjusting the Black Balance The black balance must be adjusted when: z You use your unit the first time; z Your unit has not been used for some time; z The ambient temperature has changed substantially; z The gain switchover value has been changed; or z S.GAIN (super gain) has been set with the USER MAIN/ USER1/USER2 button. 1 Set the switches as illustrated below. AUTO W/B BAL switch: Used to perform ABB.
AJ-HPX2000P(VQT1D27-1)E.book 49 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting the Electronic Shutter This section provides a description of the electronic shutter, together with setting and handling directions. Shutter Modes The table below lists the shutter modes in which the unit’s electronic shutter can be used as well as the shutter speeds which can be selected.
AJ-HPX2000P(VQT1D27-1)E.book 50 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting the Shutter Mode and Speed The shutter speed in any shutter mode is set using the SHUTTER switch. In SYNCHRO SCAN mode, shutter speed can be switched easily, using the synchro-scan adjustment switches (+/–) on the side panel. Note that the range of selectable shutter speeds may be pre-defined; whether or not to use the SYNCHRO SCAN mode may be determined through the and screens.
AJ-HPX2000P(VQT1D27-1)E.book 51 ページ ２００７年７月３０日 月曜日 午後１時３１分 Assigning Functions to USER MAIN, USER1 and USER2 Buttons The USER MAIN, USER1, and USER2 buttons can be assigned user-selected functions. To select desired functions, use the menu options USER MAIN SW, USER1 SW and USER2 SW. These options can be found in the screen, which is accessible from the CAM OPERATION page. < USER SW > USER MAIN SW USER1 SW USER2 SW ATW: Y GET: :SLOT SEL :S.GAIN :DS.
AJ-HPX2000P(VQT1D27-1)E.book 52 ページ ２００７年７月３０日 月曜日 午後１時３１分 AUDIO CH1: Function of switching the input signal source for Audio Channel 1 assigned. Pressing the button switches the input signal in the following order: FRONT > W.L. > REAR. Note that the AUDIO IN switch can also be used to change the input signal: later specification takes precedence. AUDIO CH2: Function of switching the input signal source for Audio Channel 2 assigned.
AJ-HPX2000P(VQT1D27-1)E.book 53 ページ ２００７年７月３０日 月曜日 午後１時３１分 Selecting Audio Input Signals and Adjusting Recording Levels AJ-HPX2000 supports independent 4-channel sound recording in any recording format in HD (1080i or 720P) and SD (DVCPRO50, DVCPRO, or DV with 480i or 576i) modes. When the AUDIO SELECT CH1/CH2 switch is positioned at [AUTO], the recording levels for Audio Channels 1 and 2 are automatically adjusted. To manually adjust the recording levels, position the switch at [MAN].
AJ-HPX2000P(VQT1D27-1)E.book 54 ページ ２００７年７月３０日 月曜日 午後１時３１分 Adjusting Recording Levels To adjust the recording levels for Audio Channels 1 and 2, follow the steps below. 1 Position the MONITOR SELECT CH1/2 / CH3/4selector switch at CH1/2 so that the audio level meter on the display window will provide CH1 and CH2 indications. Ensure that the channel indications displayed in the window are 1 and 2.
AJ-HPX2000P(VQT1D27-1)E.book 55 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting Time Data AJ-HPX2000 supports time codes, user bits, date, and time (real time) data, which are recorded as data for the sub-code area, VIDEO AUX area, and clip metadata files. It also includes a CTL counter and camera ID. Description of time data Time code User bits The CTL counter will measure total recording time after resetting in the recording operation.
AJ-HPX2000P(VQT1D27-1)E.book 56 ページ ２００７年７月３０日 月曜日 午後１時３１分 Recording time code and user bits The number of frames for TC varies with the settings for the input signal, system mode, and camera mode as follows. REC SIGNAL SYSTEM MODE 1080-59.
AJ-HPX2000P(VQT1D27-1)E.book 57 ページ ２００７年７月３０日 月曜日 午後１時３１分 *1 *2 *3 Adjustments and Settings for Recording It will not be slaved to a TC or UB value that is input in the SDI IN connector. Can be slaved to values input through the DVCPRO/DV connector but not to the TC for TC IN connector. If the option menu FRAME RATE UB is set to MENU, then recording is performed as per the UB or VITC UB mode. If this is the case, however, edit tools (e.g. PC edit software) cannot record the required information.
AJ-HPX2000P(VQT1D27-1)E.book 58 ページ ２００７年７月３０日 月曜日 午後１時３１分 For 1080i or 480i/576i Retaining the user bits The data set for the user bits are automatically saved and retained even if the camera-recorder is turned off. Frame rate information recorded in user bits Frame rate: 24P Over 60i (2:3) Time code frame digit 00 If video information to be recorded based on the frame rate set through the menu option CAMERA MODE is recorded in the user bits, it can be edited with editing tools (e.g.
AJ-HPX2000P(VQT1D27-1)E.
AJ-HPX2000P(VQT1D27-1)E.book 60 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting the Internal Clock’s Date and Time 1 2 3 4 Position the DISPLAY switch at [UB]. Press the HOLD button to display a date in the display window. Position the TCG switch at [SET]. Use the CURSOR and SET buttons to set the year, month and day (Y/M/D). Note that any later than 2030 cannot be set. ! button: " button: # button: $ button: 5 6 7 8 Shifts the target (blinking) digit to the right. Shifts the target (blinking) digit to the left.
AJ-HPX2000P(VQT1D27-1)E.book 61 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting the Time Code 1 2 3 Position the DISPLAY switch at [TC]. Position the TCG switch at [SET]. Note If the menu option FIRST REC TC is set to PRESET, if the time code has been set or reset, or if the time code has been switched from free run to Rec run, it is possible to regenerate the time code as the last time code of a clip recorded on the P2 card. This action requires you to preset the RET SW menu option on the SW MODE screen to R.
AJ-HPX2000P(VQT1D27-1)E.book 62 ページ ２００７年７月３０日 月曜日 午後１時３１分 Externally Locking the Time Code The unit’s internal time code generator can be locked to an external generator. In addition, the external time code generator can be locked to the unit’s internal generator. Example 2: When connecting a multiple number of units and using one of them as the reference unit Example of connections for external locking As the figure shows, connect both the reference video signal and reference time code.
AJ-HPX2000P(VQT1D27-1)E.book 63 ページ ２００７年７月３０日 月曜日 午後１時３１分 In the unit, there is a video signal delay in the camera, which is required or the process of converting video images taken with the image-shooting element from the progressive signals to the interlace signals. Since time is required for making the 2:3 pull-down from the 24P frame, there is a video signal delay in the camera.
AJ-HPX2000P(VQT1D27-1)E.book 64 ページ ２００７年７月３０日 月曜日 午後１時３１分 Example 5: When an external device is locked to the time code generator of the unit. Example 6: When an external device is locked to the time code generator of camera-recorder, which is connected in a cascade configuration.
AJ-HPX2000P(VQT1D27-1)E.book 65 ページ ２００７年７月３０日 月曜日 午後１時３１分 To externally lock the time code Follow the steps below. 1 2 3 4 Position the TCG switch at [F-RUN]. Position the DISPLAY switch at [TC]. Set the menu option GENLOCK to “EXT”. This option can be found in the screen, which is accessible from the SYSTEM SETTING page.
AJ-HPX2000P(VQT1D27-1)E.book 66 ページ ２００７年７月３０日 月曜日 午後１時３１分 Providing an ID to the Camera The camera ID is specified through the screen. The ID can include up to 10 alphanumeric characters, symbols, and/or spaces. Note When the settings menu is displayed, outputting color bar signals does not indicate the camera ID. 1 Go to the screen from the CAM OPERATION page.
AJ-HPX2000P(VQT1D27-1)E.book 67 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting UMID Information The unit supports UMID metadata. You need to specify as UMID information the country where you live (using up to three characters), organisation or company (up to four characters) and user name (up to four characters). For the country name, you must use abbreviations prescribed in 8 To exit the menu, press the MENU button. the ISO3166 Country Code*1.
AJ-HPX2000P(VQT1D27-1)E.book 68 ページ ２００７年７月３０日 月曜日 午後１時３１分 CTL Count Setting and Display By setting the DISPLAY switch to “CTL”, CTL count is displayed on the time count indication of the LCD display window. The CTL count is displayed in ±12 hours with non-dropframe. The playback order of clips recorded on a P2 card is not linear as for VTRs. It is organized according to thumbnail operations or exchanging P2 cards, and the priority of recorded clips will be altered.
AJ-HPX2000P(VQT1D27-1)E.book 69 ページ ２００７年７月３０日 月曜日 午後１時３１分 Viewfinder Screen Status Displays In addition to video images, the viewfinder displays lamps and text that indicate the settings and operating status of the unit, together with messages, a center marker, a safety zone marker and the camera ID. Lamps in the Viewfinder Screen 3.
AJ-HPX2000P(VQT1D27-1)E.book 70 ページ ２００７年７月３０日 月曜日 午後１時３１分 Selecting Viewfinder Display Information To select the information items you want to have displayed in the viewfinder screen, go to the and screens from the VF page, and turn on or off the appropriate options, or specify desired values. For directions on setting the options, see [Setting Menu Options] (page 153).
AJ-HPX2000P(VQT1D27-1)E.book 71 ページ ２００７年７月３０日 Information Item 月曜日 Indication 1080 720 480 576 2. Camera mode 3. REC mode DVCPRO HD AVC-I 100 (optional) AVC-I 50 (optional) DVCPRO50 DVCPRO DV 11/¢¢.¢ 1/60 (1/100) - 1/2000, HALF ¢¢¢min END WP LOOP INFO P2 ¢ /¢ 6. P2 card remaining [1] ¢¢¢min free space (when MODE CHECK is being performed) 7. Camera-recorder REC indication REC PRO14 - AC ADPT 8. Battery type (when MODE CHECK is being performed) ¢¢.¢V 9.
AJ-HPX2000P(VQT1D27-1)E.book 72 ページ ２００７年７月３０日 Information Item Indication 10. MODE CHECK Indication Area (STATUS: Master gain, USER SW GAIN) (Cause of !LED illumination: displayed full-screen) z Indications selected through the menu option !LED are marked with [ ! ]. z Indications which may activate the !LED are marked with [ ]. (FUNCTION: VIDEO OUT) (FUNCTION: MON OUT) (FUNCTION: P2CARD STATUS) Status Value set for the master gain Example: LOW: 0 Gain value to which S.GAIN and DS.
AJ-HPX2000P(VQT1D27-1)E.book 73 ページ Information Item 11. Camera Warning and Report Area (related to AWB, ABB and switch settings) ２００７年７月３０日 月曜日 Indication AWB A ACTIVE AWB B ACTIVE AWB A OK ¢.¢K AWB B OK ¢.¢K AWB BREAK ¢.¢K AWB NG COLOR TEMP LOW COLOR TEMP HIGH LEVEL OVER LOW LIGHT TIME OVER ATW MODE AWB PRESET ¢.¢K (Switch changeover indication) (Low light warning) (Y GET value) B-SHD ACTIVE B-SHD OK B-SHD BREAK B-SHD NG WHITE: # ¢.
AJ-HPX2000P(VQT1D27-1)E.book 74 ページ ２００７年７月３０日 Information Item Indication 13.
AJ-HPX2000P(VQT1D27-1)E.book 75 ページ ２００７年７月３０日 Information Item 月曜日 午後１時３１分 Indication Status ¢ . ¢K Color temperature assigned to A, B, and PRST of the WHITE BAL switch (this is a value stored at AWB performance or a value set through the menu option). The indication is not provided in ATW mode. 18. Filter position 1-4 – Position of the CC/ND filter. This indicates that the filter has not been set to a proper position. 19.
AJ-HPX2000P(VQT1D27-1)E.book 76 ページ ２００７年７月３０日 月曜日 午後１時３１分 P2 Card Remaining Free Space/capacity Indication Status of unit Under normal conditions Recording status Menu option 5.P2 card remaining free space 6.
AJ-HPX2000P(VQT1D27-1)E.book 77 ページ ２００７年７月３０日 月曜日 午後１時３１分 Indications Available in the Viewfinder Screen Selectable between on and off through menu options Provided when the appropriate Provided during status is MODE CHECK*1 encountered. Selectable Provided during playback ⃝ – ● ⃝ – 2. Camera mode ⃝ – ● ⃝ – 3. REC mode ⃝ – ● ⃝ – 4. Shutter speed/mode ⃝ ⃝ ● ⃝ – 5. P2 card remaining free space ⃝ – ● ⃝ – 6. P2 card remaining free space (MODE CHECK) – – ● ⃝ – 7.
AJ-HPX2000P(VQT1D27-1)E.book 78 ページ ２００７年７月３０日 月曜日 午後１時３１分 Display Modes and Setting Changes/adjustment Result Messages The messages that appear on the viewfinder screen to indicate changes to settings and adjustment results may be limited, or set not to appear, through the menu option DISP MODE. This menu option can be found in the screen, which is accessible from the VF page. For directions on navigating the menu, see [Setting Menu Options] (page 153).
AJ-HPX2000P(VQT1D27-1)E.book 79 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting the Marker Displays The center, safety zone, safety zone area and frame markers may be set to ON or OFF, along with specifications of the marker types. To set and select markers, go to the VF MARKER screen from the VF page and select the appropriate options. For directions on navigating the menu, see [Setting Menu Options] (page 153).
AJ-HPX2000P(VQT1D27-1)E.book 80 ページ ２００７年７月３０日 月曜日 午後１時３１分 Adjusting and setting the LCD monitor 5 Using the LCD Monitor 1 2 Turn on the POWER switch of the unit. Slide the OPEN button in the arrow 1 direction to open the LCD monitor in the arrow 2 direction. Through the menu option LCD MON CHAR, specify whether or not the LCD should display the same characters as the viewfinder. This menu option can be found in the
AJ-HPX2000P(VQT1D27-1)E.book 81 ページ ２００７年７月３０日 月曜日 午後１時３１分 Selection of video output signals The unit employs the VIDEO OUT connector and the MON OUT connector as connectors for outputting video signals. Settings of signals output from VIDEO OUT connector The signal modes for outputting signals from the VIDEO OUT connector are switched with the VIDEO OUT switch.
AJ-HPX2000P(VQT1D27-1)E.book 82 ページ ２００７年７月３０日 月曜日 午後１時３１分 Settings of signals output from MON OUT connector The MON OUT connector outputs down-converted analog signals. Set the video signals output from the MON OUT connector by using the MONITOR OUT item on the menu (
AJ-HPX2000P(VQT1D27-1)E.book 83 ページ ２００７年７月３０日 月曜日 午後１時３１分 Handling data Set data file configuration The unit employs 5 sets for the file data area. For menu items that can be read from or stored in the respective areas, refer to [Menu] (page 151) Notes z For information about how to navigate through the menu for this section, see [Setting Menu Options] (page 153). z Access the respective data settings files after switching the PC MODE to “OFF”.
AJ-HPX2000P(VQT1D27-1)E.book 84 ページ ２００７年７月３０日 月曜日 午後１時３１分 Handling SD memory cards An SD memory card may be inserted or removed, either before or after the power is turned on. To insert an SD memory card Open the lid of the switch cover, and insert an SD memory card (optional accessory) into the SD memory card slot with the notch upward. Close the lid. To remove the SD memory card Open the lid of the switch cover, and ensure that the BUSY lamp is not illuminated.
AJ-HPX2000P(VQT1D27-1)E.book 85 ページ 4 ２００７年７月３０日 月曜日 午後１時３１分 To format the SD memory card, turn the JOG dial button to move the cursor to YES. Then, press the dial button. When the SD memory card has been formatted, the following message appears: To write set data on an SD memory card 1 Navigate the menu to the screen. To select a file number 2 Turn the JOG dial button to move the cursor to the option [W. SELECT]. Then, press the dial button.
AJ-HPX2000P(VQT1D27-1)E.book 86 ページ 6 ２００７年７月３０日 8 午後１時３１分 Turn the JOG dial button until a desired character appears. The characters that appear are switched in the following order: Space: Ð Alphabetical characters: Ð Numerals: Ð Symbols: 7 月曜日 A to Z 0 to 9 ', >, <, /, - Error message Remedy WRITE NG Insert an SD memory card. NO CARD (No SD memory card inserted.) WRITE NG FORMAT ERROR (SD memory card not properly formatted.) The card has not been formatted using the unit. Replace the card.
AJ-HPX2000P(VQT1D27-1)E.book 87 ページ ２００７年７月３０日 月曜日 午後１時３１分 To read data on an SD memory card 1 6 Navigate the menu to the screen. Turn the JOG dial button to move the cursor to YES. Then, press the dial button. When the data has been read, the following message appears: To select a file number 2 Turn the JOG dial button to move the cursor to the menu option [R. SELECT]. Then, press the dial button. READ OK < SD CARD READ/WRITE > R.SELECT READ W.
AJ-HPX2000P(VQT1D27-1)E.book 88 ページ ２００７年７月３０日 月曜日 午後１時３１分 How to Use the User Data It is possible to transfer settings and other data to the user area of the internal memory of the unit. This data allows you to quickly reproduce an optimum setup state. 2 Turn the JOG dial button to move the cursor to the option READ USER DATA. < SCENE > # To write data, go to the screen from the FILE page. To read the written user data, go to the screen from the FILE page.
AJ-HPX2000P(VQT1D27-1)E.book 89 ページ ２００７年７月３０日 月曜日 午後１時３１分 How to Use Scene File Data It is possible to write the settings data into the scene file area of the internal memory of the unit, or to read data written in this area. Four types of scene files are available. This data allows you to quickly reproduce an optimum setup state. To change the settings, go to the screen from the FILE page. 7 8 Turn the JOG dial button to move the cursor to YES. Then, press the dial button.
AJ-HPX2000P(VQT1D27-1)E.book 90 ページ ２００７年７月３０日 月曜日 午後１時３１分 To read settings data for scene files 1 2 3 Navigate the menu to the screen. Turn the JOG dial button to move the cursor to the option SCENE SEL. Press the JOG dial button to blink scene file numbers. Then, turn the dial button to select a desired scene file number. To return data for scene files to their defaults 1 2 3 Navigate the menu to the screen. Turn the JOG dial button to move the cursor to the option SCENE SEL.
AJ-HPX2000P(VQT1D27-1)E.book 91 ページ ２００７年７月３０日 月曜日 午後１時３１分 To title settings data for scene files 1 2 10 Press the JOG dial button to display the following message: Navigate the menu to the screen. Turn the JOG dial button to move the cursor to the option [TITLE 1 - 4] for the appropriate scene file.
AJ-HPX2000P(VQT1D27-1)E.book 92 ページ ２００７年７月３０日 月曜日 午後１時３１分 Resetting Menu Option Settings to Defaults The menu settings can be reset to their defaults. To reset the settings to their defaults, select the menu option READ FACTORY DATA in the screen, which is accessible from the FILE page. All settings will be reset to their defaults.
AJ-HPX2000P(VQT1D27-1)E.book 93 ページ ２００７年７月３０日 月曜日 午後１時３１分 To save the lens file into the built-in memory 7 Select the file No. 1 2 3 Using the menu operations, open the screen from the FILE page. Turn the JOG dial button to move the arrow (cursor) to the FILE SELECT item. Adjustments and Settings for Recording Press the JOG dial button and the file number will flash. Turn the JOG dial button to select the file (1 to 8) to be recorded.
AJ-HPX2000P(VQT1D27-1)E.book 94 ページ ２００７年７月３０日 月曜日 午後１時３１分 13 When the JOG dial button is pressed, the following 14 Turn the JOG dial button to move the arrow (cursor) to message appears. YES, and press the JOG dial button. The current white shading correction value, the flare compensation value, and the RB gain offset correction value are stored in the built-in memory of the unit.
AJ-HPX2000P(VQT1D27-1)E.book 95 ページ ２００７年７月３０日 月曜日 午後１時３１分 To write in and read out the lens file to/from the SD memory card The contents of the eight lens files stored in the unit’s internal memory can be saved onto an SD memory card as card files under a single title. A total of eight titles can be saved on an SD memory card. Furthermore, the eight lens files saved under one title on an SD memory card can be loaded into the unit’s internal memory.
AJ-HPX2000P(VQT1D27-1)E.book 96 ページ ２００７年７月３０日 月曜日 午後１時３１分 Loading lens files from the SD memory card 1 2 3 Using menu operations, open the screen from the FILE page. Turn the JOG dial button to move the arrow (cursor) to the CARD FILE SELECT item. Press the JOG dial button and the card file number will flash. Turn the JOG dial button to select the file (1 to 8) to be read.
AJ-HPX2000P(VQT1D27-1)E.book 97 ページ ２００７年７月３０日 月曜日 午後１時３１分 Preparation Power Supply A battery pack or an external DC power supply can be used as AJ-HPX2000’s power supply. Using a Battery Pack Preparation Battery packs from the following manufacturers can be used: • Anton/Bauer • IDX • PACO • Sony The type of the battery can be checked or changed through the viewfinder or menu screen on the monitor.
AJ-HPX2000P(VQT1D27-1)E.book 98 ページ ２００７年７月３０日 月曜日 午後１時３１分 Mounting the Battery and Setting the Battery Type Using an Anton/Bauer Battery Pack 1 Mount the Anton/Bauer battery pack. Power supply output connector for lighting 3 Setting the battery type. Select the battery type listed under BATTERY SELECT. Select BATTERY SELECT from the screen in the MAIN OPERATION page. Please refer to [BATTERY SETTING1] (page 179) for more information.
AJ-HPX2000P(VQT1D27-1)E.book 99 ページ ２００７年７月３０日 月曜日 午後１時３１分 When using a V-mount type battery pack Using an NP-1 type battery pack Mount the V-mount adapter plate. Insert the plate and slide it in the direction of the arrow. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of fire or electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
AJ-HPX2000P(VQT1D27-1)E.book 100 ページ ２００７年７月３０日 月曜日 午後１時３１分 Use of the external DC power supply 1 Connect the external DC power supply to the DC IN socket on the unit. DC IN Socket External DC power supply 2 3 Turn “ON” the power switch of the external DC power supply. (If the power switch is available on the external DC power supply) Turn ON the POWER switch on the unit. Inrush current is generated when the power of the unit is turned on.
AJ-HPX2000P(VQT1D27-1)E.book 101 ページ ２００７年７月３０日 月曜日 午後１時３１分 Mounting the lens and Performing the Flange Back and White Shading Adjustments Mounting the Lens 1 Adjusting the Lens Flange Back Raise the lens clamping lever and remove the mount cap. Lens Clamping Lever Note Please also refer to the lens instruction manual for directions on adjustment and locations of individual lens parts.
AJ-HPX2000P(VQT1D27-1)E.book 102 ページ ２００７年７月３０日 8 9 月曜日 午後１時３１分 Repeat Steps 5 to 7 until the lens is in focus at both the telephoto and wide-angle positions. 7 Firmly tighten the F.f ring clamping screw. Notes z The zebra pattern will not cover the whole screen if there is any unevenness in the lighting. In this case, make adjustments to the position of the lighting, etc. z Make adjustments to the position of the lighting, etc. also when the lens aperture is not between F4 and F10.
AJ-HPX2000P(VQT1D27-1)E.book 103 ページ ２００７年７月３０日 月曜日 午後１時３１分 When making the white shading correction, make the adjustment while observing the R, G, and B waveforms in the horizontal and vertical directions with the waveform monitor. This now completes the white shading adjustments. The adjustment values are now stored in the non-volatile memory so that even when the unit’s power is turned off, there will be no further need to perform the white shading adjustment.
AJ-HPX2000P(VQT1D27-1)E.book 104 ページ ２００７年７月３０日 月曜日 午後１時３１分 Preparing for Audio Input Take the following steps to prepare the camera for connecting audio input devices. When Using the Front Microphone AJ-HPX2000 can be equipped with the AJ-MC900G stereo microphone kit (an extra-cost option). 1 3 Connect the microphone cable to the MIC IN jack on the camera. Open the microphone holder. MIC IN Jack 4 2 Mount the microphone and tighten the clamping screw.
AJ-HPX2000P(VQT1D27-1)E.book 105 ページ ２００７年７月３０日 月曜日 午後１時３１分 When Using Audio Devices 1 2 3 Connect the audio device to the AUDIO IN jack with the XLR cable. Set the AUDIO IN switch to [REAR] for the channel to which the XLR cable is connected. Set the LINE/MIC/+48V selector switch on the rear panel to [LINE]. LINE/MIC/+48V Selector Switch Preparation AUDIO IN Jack AUDIO IN Switch Mounting the Camera on a Tripod When mounting the camera on a tripod, use the tripod adapter supplied with the camera.
AJ-HPX2000P(VQT1D27-1)E.book 106 ページ ２００７年７月３０日 月曜日 午後１時３１分 Attaching the Shoulder Strap To detach the shoulder strap, first open the hooks, then detach the strap. Shoulder Strap Note Make sure that the shoulder strap is securely attached.
AJ-HPX2000P(VQT1D27-1)E.book 107 ページ ２００７年７月３０日 月曜日 午後１時３１分 Connection of the remote control unit (AJ-RC10G) Switch functions in the remote control mode In the remote control mode, the following switches and buttons on the unit are disabled.
AJ-HPX2000P(VQT1D27-1)E.book 108 ページ ２００７年７月３０日 月曜日 午後１時３１分 Connection of the external switch It is possible to draw 1.5 A current from the DC OUT connector of the unit. REC start/stop can be controlled by connecting an external switch to this connector. Since a tally lamp can be used by connecting an LED to this connector, it is useful for shooting video when fixing the camera on a crane. DC OUT connector 4 1 3 2 Connector at the cable side HR10A-7R-4P(73) (Hirose Denki) LED Resistance Max.
AJ-HPX2000P(VQT1D27-1)E.book 109 ページ ２００７年７月３０日 月曜日 午後１時３１分 Manipulating Clips with Thumbnails A clip is a data group that includes the images and voices created from one shooting session, together with additional information such as text memos and meta data. The following manipulations can be performed using the cursor and SET buttons, while checking the images displayed on the LCD monitor: z Playback, delete, copy or restore the clip. z Add or delete a shot mark and a text memo on the clip thumbnail.
AJ-HPX2000P(VQT1D27-1)E.book 110 ページ ２００７年７月３０日 月曜日 午後１時３１分 Thumbnail Screen Press the THUMBNAIL button to display the thumbnail screen on the LCD monitor. Pressing the THUMBNAIL button again returns the display to the regular display. When switching is done from the regular screen display to the thumbnail screen display, all the clips will be displayed on the thumbnail screen. Pressing the MENU button allows you to navigate the thumbnail menu.
AJ-HPX2000P(VQT1D27-1)E.book 111 ページ ２００７年７月３０日 月曜日 午後１時３１分 4. Recording mode 14. The recording mode for the clip on which the pointer is located is indicated. 5. System format The format for the clip on which the pointer is located is indicated. 6. Duration The duration of the clip on which the pointer is located is indicated. Edit Copied Clip Indicator This marker is displayed on a clip when the model supports edit copy, such as the AJ-HPM100.
AJ-HPX2000P(VQT1D27-1)E.book 112 ページ ２００７年７月３０日 月曜日 午後１時３１分 Selecting Thumbnails Multiple thumbnails can be randomly selected in the thumbnail screen. 1 2 Use the cursor buttons to move the pointer (yellow frame) to the desired clip and press the SET button. The frame around the selected thumbnail changes to a blue frame. Press the SET button again to deselect the clip. MENU Button LCD Monitor Additional clips can be selected by repeating Step 1.
AJ-HPX2000P(VQT1D27-1)E.book 113 ページ ２００７年７月３０日 月曜日 午後１時３１分 Switching the Thumbnail Display The display can be switched so that only those clips matching the specified conditions are displayed in the thumbnail screen. 1 2 Press the THUMBNAIL button. The thumbnail screen appears on the LCD monitor. 3 Select THUMBNAIL from the thumbnail menu. Switch the thumbnail display by selecting one of the following items: Press the THUMBNAIL MENU button. The thumbnail menu appears. ALL CLIP: Display all clips.
AJ-HPX2000P(VQT1D27-1)E.book 114 ページ ２００７年７月３０日 月曜日 午後１時３１分 Changing thumbnails It is possible to replace thumbnails with images that include previously attached text memos while images are recorded or played back. 1 2 3 4 5 Add text memos to images that you intend to change. Refer to [Text Memo Function] (page 40) for the method to add text memos. Select THUMBNAIL > TEXT MEMO CLIPS to display thumbnails of the clips with text memos.
AJ-HPX2000P(VQT1D27-1)E.book 115 ページ ２００７年７月３０日 月曜日 午後１時３１分 Shot Mark A shot mark can be added to a clip thumbnail to distinguish this clip from the others. 1 2 3 4 Press the THUMBNAIL button. The thumbnail screen appears on the LCD monitor. Use the cursor buttons to move the pointer over the clip to which you want to attach a shot mark. Press the Shot Mark button. Manipulating Clips with Thumbnails A shot mark will be attached to the clip thumbnail under the pointer.
AJ-HPX2000P(VQT1D27-1)E.book 116 ページ ２００７年７月３０日 月曜日 午後１時３１分 Playing back a clip at the position where a text memo is recorded 1 2 Press the THUMBNAIL button. The thumbnail screen appears on the LCD monitor. 3 Press the THUMBNAIL MENU button and select THUMBNAIL > TEXT MEMO CLIPS from the thumbnail menu. The clip thumbnails with text memos attached are displayed in the upper section of the LCD monitor.
AJ-HPX2000P(VQT1D27-1)E.book 117 ページ ２００７年７月３０日 月曜日 午後１時３１分 Using a text memo to break a clip and copy the necessary portion 1 2 3 Select a desired text memo in a clip by carrying out steps 1-3 for [Playing back a clip at the position where a text memo is recorded] (page 116). 4 Move the pointer to the desired text memo, and then press the SET button. You can select more than one text memo. Press the THUMBNAIL MENU button to select OPERATION > COPY.
AJ-HPX2000P(VQT1D27-1)E.book 118 ページ ２００７年７月３０日 月曜日 午後１時３１分 Reconnection of Incomplete Clips Incomplete clips may be generated when clips recorded on multiple P2 cards (connected clips) are separately copied to different cards. Reconnection function generates one clip (the original, connected clip) from incomplete clips. 1 2 Press the THUMBNAIL button. The thumbnail screen appears on the LCD monitor. Use the cursor and SET button to select incomplete clips to reconnect.
AJ-HPX2000P(VQT1D27-1)E.book 119 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting of Clip Meta Data Information such as the name of person who shot the video, the name of the reporter, the shooting location, or a text memo can be read from the SD memory card, and can be recorded as Clip Meta Data. 1 2 Reading Clip Meta Data (metadata upload) Regarding SD memory cards to be used, see (page 21). Insert the SD memory card that contains the Clip Meta Data (metadata upload file).
AJ-HPX2000P(VQT1D27-1)E.book 120 ページ ２００７年７月３０日 月曜日 午後１時３１分 *1 The USER CLIP NAME recording method is selectable. For details, refer to [Selecting the USER CLIP NAME recording method] (page 121). *2 Be sure to enter TEXT when entering MEMO. It is not possible to record only PERSON or OFFSET. 4 While viewing the settings for the metadata, use the cursor buttons to move the pointer to the desired option. Then, press the SET button.
AJ-HPX2000P(VQT1D27-1)E.book 121 ページ ２００７年７月３０日 月曜日 午後１時３１分 Note Selecting the USER CLIP NAME recording method Select META DATA > USER CLIP NAME from the thumbnail menu to select the recording method. Two options are available: TYPE1 and TYPE2.
AJ-HPX2000P(VQT1D27-1)E.book 122 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting of Proxy (optional) By attaching the video encoder card (AJ-YAX800G, optional) either to the optional slot or Slot 5, it is possible to specify the proxy recording setting. The video encoder card is not recognized when inserted if the power for the unit is turned ON. Insert the video encoder card after turning off the power for the unit. Select OPERATION > DEVICE SETUP > PROXY from the thumbnail menu to specify the setting.
AJ-HPX2000P(VQT1D27-1)E.book 123 ページ ２００７年７月３０日 月曜日 午後１時３１分 Formatting SD memory cards SD memory cards can also be formatted from the thumbnail screen. With an SD memory card inserted into the camera-recorder, perform the following operation: 1 2 4 Press the THUMBNAIL MENU button and select OPERATION > FORMAT from the thumbnail menu. The following screen appears. Select “SD CARD”. Select “EXIT” if formatting is not required. Manipulating Clips with Thumbnails 3 Press the THUMBNAIL button.
AJ-HPX2000P(VQT1D27-1)E.book 124 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting the Thumbnail Display Mode The thumbnail display mode can be customised to suit your preferences. 1 2 Press the THUMBNAIL button. The thumbnail screen appears on the LCD monitor. Press the THUMBNAIL MENU button and select THUMBNAIL → SETUP from thethumbnail menu. The following screen appears.
AJ-HPX2000P(VQT1D27-1)E.book 125 ページ ２００７年７月３０日 月曜日 午後１時３１分 Properties The clip’s properties and the P2 card’s status are displayed. It is possible to edit and rewrite recorded clip metadata while clip properties are displayed. Clip Property From the thumbnail menu, select PROPERTY > CLIP PROPERTY. The following screen appears. 4. Clip Information Displays detailed information about the clip. 1 2 5 4 1. Clip Number 2. Thumbnail 3.
AJ-HPX2000P(VQT1D27-1)E.book 126 ページ ２００７年７月３０日 3 月曜日 午後１時３１分 Press the SET button. The input window (soft keyboard) for modifying metadata is displayed. Use the keyboard to modify the metadata. 4 Press OK on the keyboard to write the modified metadata on the clip and return to the metadata window. The input window (soft keyboard) for modifying metadata is displayed. Use the keyboard to modify the metadata.
AJ-HPX2000P(VQT1D27-1)E.book 127 ページ ２００７年７月３０日 月曜日 午後１時３１分 Contents of P2 Card Status Display Settings From the thumbnail menu, select PROPERTY > CARD STATUS. The following screen appears. When “REMAIN” is selected: 1 When “USED” is selected: 2 1 2 3 3 5 5 4 4 The 1. Write-protect Mark mark appears if the P2 card is write-protected. 2. P2 Card Status (remaining free space) The remaining memory capacity of the P2 card is indicated by a bar graph and percentage.
AJ-HPX2000P(VQT1D27-1)E.book 128 ページ ２００７年７月３０日 月曜日 午後１時３１分 SD memory card Status Display The status display enables a confirmation of the SD memory card formatted condition, available memory capacity etc. From the thumbnail menu, select PROPERTY > DEVICES > SD CARD. If the format is compatible with SD standards, the message “SD STANDARD: SUPPORTED” is displayed. If the format is not compatible with SD standards, the message “SD STANDARD: NOT SUPPORTED” is displayed.
AJ-HPX2000P(VQT1D27-1)E.book 129 ページ ２００７年７月３０日 月曜日 午後１時３１分 Connection with external device Connection through the DVCPRO/DV connector Records of signals input to the DVCPRO/DV connector 1 2 Open the <1394 SETTING> on the SYSTEM SETTING page and confirm that the settings in the 1394 IN CH item and the 1394 OUT CH item are set to “AUTO”. In case of input from the IEEE1394 interface, set REC SIGNAL to “1394”. The REC SIGNAL option must be selected from the menu on the SYSTEM SETTING page.
AJ-HPX2000P(VQT1D27-1)E.book 130 ページ ２００７年７月３０日 月曜日 午後１時３１分 External device control through DVCPRO/DV connection The DVCPRPO/DV connector can be connected with an external device for recording backup copies to control the start and stop of recording. 1 2 3 When connecting the 1394 (DV) cable, see [32.DVCPRO/DV connector] (page 21). Set the 1394 CONTROL menu option on the 1394 SETTING screen on the SYSTEM SETTING page to BOTH.
AJ-HPX2000P(VQT1D27-1)E.book 131 ページ ２００７年７月３０日 月曜日 午後１時３１分 Connection with external devices using the USB 2.0 port Connection with a PC in the USB DEVICE mode By connecting AJ-HPX2000 with an external PC using USB 2.0, the P2 card connected to AJ-HPX2000 can be used as a mass storage device. Notes Procedures for establishing a connection with a PC 1 Connect the USB cable to the USB 2.0 port. Notes z The USB 2.0 cable is not included with the camerarecorder.
AJ-HPX2000P(VQT1D27-1)E.book 132 ページ ２００７年７月３０日 月曜日 午後１時３１分 USB HOST mode AJ-HPX2000 can be connected to a hard disc drive that supports USB 2.0 to store data from cards on it, view thumbnails for stored clips, and write data back to P2 cards. Switching to the USB HOST mode 1 2 By navigating the menu, set the PC MODE SELECT menu option on the SYSTEM MODE screen to USB HOST, then the PC MODE option to ON. This will place the camera-recorder in USB HOST mode.
AJ-HPX2000P(VQT1D27-1)E.book 133 ページ ２００７年７月３０日 月曜日 午後１時３１分 Viewing hard disc drive information 1. You can view the information on the hard disc drive connected via USB 2.0 with the following steps. 1 Switch the mode to USB HOST. For more information, see [Switching to the USB HOST mode] (page 132). 2 PARTITION This section indicates the type of the hard disc drive. The available functions depend on the type of hard disc drive.
AJ-HPX2000P(VQT1D27-1)E.book 134 ページ ２００７年７月３０日 月曜日 午後１時３１分 8. MODEL 11. VERIFY This section indicates the model of the P2 card that originally contained data on the partition. This section indicates the verification setting and results at the time the data on the partition was recorded. Note ON:FINISHED : Verification was performed and the results agreed. ON:FAILED : Verification was performed and the results did not agree. OFF : No verification was performed.
AJ-HPX2000P(VQT1D27-1)E.book 135 ページ ２００７年７月３０日 月曜日 午後１時３１分 Writing data on a hard disc drive 1 2 3 4 5 Connect a hard disc drive via USB. A hard disc drive that has not been formatted with the camera-recorder must be formatted as directed in [Formatting a hard disc drive] (page 134). Insert a P2 card. 1 2 3 4 Press the thumbnail button to display the thumbnail screen. Press the MENU button and select HDD > EXPLORE from the thumbnail menu.
AJ-HPX2000P(VQT1D27-1)E.book 136 ページ ２００７年７月３０日 6 月曜日 午後１時３１分 Select YES to start writing data to the cards. To disable verification during writing, select HDD > SETUP from the thumbnail menu and set the option VERIFY to OFF. This speeds up writing without verifying data writing. 7 When the writing is completed, the message “COPY COMPLETED!” is displayed.
AJ-HPX2000P(VQT1D27-1)E.book 137 ページ ２００７年７月３０日 月曜日 午後１時３１分 Connection using the SDI IN connector (when AJ-YA350AG attached) 1 2 3 Confirm that the HD/SD-SDI input board (AJYA350AG: optional accessory) is attached to the unit and that the wires are connected properly. For details, refer to the installation manual for the AJ-YA350AG. Confirm that the connected device has the same signal format as camera-recorder.
AJ-HPX2000P(VQT1D27-1)E.book 138 ページ ２００７年７月３０日 月曜日 午後１時３１分 Maintenance and Inspections Inspections Before Shooting Make sure you check that the system is operating normally before embarking on a shoot. We recommend using a color video monitor to check the image. Preparing for Inspections 1 2 3 Mount a charged battery pack. Turn the power switch ON and check that 5 or more BATT indication marks appear. z If fewer than 5 BATT indication marks appear, replace the battery with a fully-charged battery.
AJ-HPX2000P(VQT1D27-1)E.book 139 ページ ２００７年７月３０日 月曜日 午後１時３１分 Inspecting the Memory Recording Functions Make sure you successively carry out the inspections from [1. Inspecting the P2 Card Recording] to [4. Inspecting the Earphone and Speaker]. 1. Inspecting the P2 Card Recording 1 6 7 8 9 2 Check on the display inside the viewfinder that the remaining P2 card recording capacity is sufficient.
AJ-HPX2000P(VQT1D27-1)E.book 140 ページ ２００７年７月３０日 月曜日 午後１時３１分 6. Inspection of the clock, time code, and user bits 1 2 3 4 5 Set the user’s bit as required. Please refer to [Setting of the user bits] (page 57) for the setting procedures. 6 7 Set the time code. Please refer to [Setting the Time Code] (page 61) for the setting procedures. Set the TCG switch to [R-RUN]. Press the REC START/STOP button. Check that the counter display number changes as recording progresses. Set the TCG switch to [F-RUN].
AJ-HPX2000P(VQT1D27-1)E.book 141 ページ ２００７年７月３０日 月曜日 午後１時３１分 Connector Signals DC IN 1 GND 2 NC 3 NC 4 +12V Matsushita part number K1AA104H0038 Maker part number HA16RX-4P（SW1） (Hirose Denki) 4 1 2 3 Note Matsushita part number K1AY104J0001 Maker part number HR10A-7R-4SC(73) (Hirose Denki) DC OUT 1 GND 2 R TALLY (Open collector) 3 REC START SW 4 +12V OUT (Max. 1.
AJ-HPX2000P(VQT1D27-1)E.
AJ-HPX2000P(VQT1D27-1)E.book 143 ページ ２００７年７月３０日 月曜日 午後１時３１分 LENS 1 RET-SW ON/OFF of the return video RETURN ON: GND RETURN OFF: OPEN 2 REC-START/STOP Control for recording start/stop +5 V 0V Matsushita part number K1AY112JA001 Maker part number HR10A-10R-12SC(71) (Hirose Denki) 9 1 10 8 2 11 12 7 6 3 4 5 START STOP START GND GND 4 IRIS-AUTO ON/OFF of the forced iris servo SERVO ON: +5V±0.5V SERVO OFF: OPEN 5 IRIS-CONT Control output for the lens iris F2.8: –6.2 V, F16: +3.
AJ-HPX2000P(VQT1D27-1)E.
AJ-HPX2000P(VQT1D27-1)E.book 145 ページ ２００７年７月３０日 月曜日 午後１時３１分 Warning System Warning Description Tables If a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the WARNING lamp, lamps inside the viewfinder and a warning tone. Note The WARNING lamp has the highest priority, followed by the tally lamp, and then the warning tone. When multiple errors occur simultaneously a higher priority indication will be triggered.
AJ-HPX2000P(VQT1D27-1)E.book 146 ページ ２００７年７月３０日 月曜日 午後１時３１分 5. P2 Card Fully Recorded Display window indication WARNING lamp Tally lamp All 7 bar indicators for remaining MEDIA capacity start blinking. This lamp will illuminate continuously until an operation is made after recording. This lamp will flash 4 times every second until an operation is made after recording. 7. Recording Error Display window indication WARNING lamp Viewfinder The END indicator blinks.
AJ-HPX2000P(VQT1D27-1)E.book 147 ページ ２００７年７月３０日 月曜日 午後１時３１分 9. 1394 Error Display window indication WARNING lamp Tally lamp Viewfinder Warning tone Warning description 12. P2 Card Error The 1394 E-¢¢ indicator in the display window blinks. For more information, see [1394 Error Codes] (page 148). Blinks 4 times per second while the WARNING lamp recording is continuing. Blinks 4 times per second while the TALLY LAMP recording is continuing.
AJ-HPX2000P(VQT1D27-1)E.book 148 ページ ２００７年７月３０日 月曜日 午後１時３１分 Error Codes The following error codes are displayed in the display window if an error occurs in the camera: Confirm the type of warning and refer to the details in the [Warning Description Tables] (page 145) for countermeasures. Code No. Description Type of warnings E-11 Video initialisation error E-27 Recording control error 1. System Errors 1. System Errors E-30 P2 card removal error 2.
AJ-HPX2000P(VQT1D27-1)E.book 149 ページ ２００７年７月３０日 月曜日 午後１時３１分 Card Warning Code Code No. Description E-70 The directory organization on the inserted P2 card does not comply with the standards. ([DIR NG CARD (Slot No.)] is indicated on the viewfinder.) Although different kinds of recording operations will function, data may not be recorded properly. Use the unit to format the card immediately. E-71 A P2 card was inserted where the number of rewrites exceeds the limit of the standards.
AJ-HPX2000P(VQT1D27-1)E.book 150 ページ ２００７年７月３０日 Item Soft keyboard Message 午後１時３１分 Description Measure CANNOT CHANGE! [PERSON] will be entered while the text memo is not available. Enter [TEXT] before entering [PERSON]. CANNOT SET! INVALID VALUE! The entered value is incorrect. Change the value. HDD CAPACITY FULL! Not enough space left on the hard disk. There is not enough space on the connected hard disk. Use a new hard disk or formatted hard disk.
AJ-HPX2000P(VQT1D27-1)E.book 151 ページ ２００７年７月３０日 月曜日 午後１時３１分 Menu Menu Configuration MENU USER MENU SYSTEM SETTING MAIN MENU OPTION VF CAMERA ID SHUTTER SPEED SHUTTER SELECT USER SW SW MODE WHITE BALANCE MODE USER SW GAIN LENS/IRIS CAM OPERATION Opening the Menus USER MENU: Displayed when button is pressed. the MENU MAIN MENU: Displayed when the MENU button is pressed for at least 3 seconds. OPTION MENU: Displayed when the MENU button is pressed while pressing the LIGHT button.
AJ-HPX2000P(VQT1D27-1)E.book 152 ページ ２００７年７月３０日 月曜日 午後１時３１分 USER MENU: USER MENU is factory-set. The menu can LIGHT button be configured to suit your preferences by specifying each option according to your purposes and frequency of use, through the screen, which is accessible from the MAIN MENU page. For more information, see [Selecting Options for USER MENU] (page 154). To display USER MENU, press the MENU button. MAIN MENU: Allows you to set all options on the settings menu.
AJ-HPX2000P(VQT1D27-1)E.book 153 ページ ２００７年７月３０日 月曜日 午後１時３１分 Setting Menu Options The menu options are set with the MENU and JOG dial buttons. The menu comprises main menu, sub-menus and options menus. The data specified through menu options are written and saved in the internal memory of the unit. This section describes how to set options in MAIN MENU. The other menus can be configured in the same manner (the method of displaying the menu screen depends on the particular menu).
AJ-HPX2000P(VQT1D27-1)E.book 154 ページ ２００７年７月３０日 月曜日 午後１時３１分 Selecting Options for USER MENU Go to the USER MENU SELECT page from MAIN MENU. Then, open relevant options menu screens to select options to add to USER MENU. Only the selected options are displayed as options in USER MENU. For information about how to navigate this menu, see [Setting Menu Options] (page 153).
AJ-HPX2000P(VQT1D27-1)E.book 155 ページ ２００７年７月３０日 月曜日 午後１時３１分 Menu Description Tables SYSTEM SETTING SYSTEM MODE CAMERA MODE (1080-59.94i /480-59.94i) 60i 30P 24P 24PA (1080-50i /576-50i) 50i 25P (720-59.94P) 60P 30P 24P (720-50P) 50P – C U F R 25P Items/ Adjustable Remarks Data Saved Range Select the aspect ratio for recording. (In 16:9 ASPECT 4:3 SD mode only） 16:9: Record in <16:9> aspect ratio. 4:3: Record in <4:3> aspect ratio.
AJ-HPX2000P(VQT1D27-1)E.book 156 ページ ２００７年７月３０日 月曜日 午後１時３１分 SYSTEM MODE Items/ Adjustable Remarks Data Saved Range Used to enable or disable the mode that PC MODE ON allows the camera-recorder to be OFF connected to a PC or an external hard disk drive via USB 2.0. ON: Sets the camera-recorder to the mode selected through the PC MODE SELECT menu option. OFF: Disables the PC MODE for normal operation. Note Once the power is turned off, the option is always set to OFF when the power is turned on next time.
AJ-HPX2000P(VQT1D27-1)E.book 157 ページ ２００７年７月３０日 月曜日 午後１時３１分 REC FUNCTION Items/ Adjustable Remarks Data Saved Range INTERVAL ON Sets INTERVAL REC function. REC MODE ONE SHOT ON: Uses internal memory to perform interval recording. OFF ONE SHOT: Performs “one-shot” recording for the duration specified under REC TIME, and then stops. OFF: INTERVAL REC is not performed. Note This item cannot be changed when [ON] – C U F – is selected in LOOP REC MODE.
AJ-HPX2000P(VQT1D27-1)E.book 158 ページ ２００７年７月３０日 月曜日 午後１時３１分 OUTPUT SEL DOWNCON SETTING Items/ Adjustable Remarks Data Saved Range OUTPUT ITEM MENU ONLY Set the character contents superimposed onto the output signals TC for the VIDEO OUT connector (Analog STATUS or SDI) and MON OUT connector. MENU ONLY: Displays only when the menu characters are superimposed. No display appears when other characters are superimposed. TC:Display the time code. (Displays the menu when menu characters are superimposed.
AJ-HPX2000P(VQT1D27-1)E.book 159 ページ ２００７年７月３０日 月曜日 午後１時３１分 LCD MONITOR GENLOCK Items/ Adjustable Remarks Data Saved Range Adjust the LCD monitor brightness. BRIGHTNESS –7 : +0 : – C U F – +7 COLOR –7 : LEVEL +0 Adjust the LCD monitor chroma level. : – C U F – +7 CONTRAST –7 Adjust the LCD monitor contrast. : +0 : – C U F – +7 BACKLIGHT NORMAL HIGH – C U F – – C U F – ASPECT CONV. – C U F – SQUEEZE LT.BOX Select whether or not to change the LCD monitor to mirror image.
AJ-HPX2000P(VQT1D27-1)E.book 160 ページ ２００７年７月３０日 月曜日 午後１時３１分 1394 SETTING Items/ Adjustable Remarks Data Saved Range For selecting the channels for audio 1394 AUDIO CH1/CH2 signals output from the DVCPRO/DV OUT CH3/CH4 connector when the camera-recorder is operating in DVCPRO or DV mode (for 480-59.94i or 576-50i only) Note When CH3/CH4 is selected, no sound is heard in the following outputs: z EE output if the 25M REC CH SEL menu option on the MIC AUDIO screen on the MAIN OPERATION page is set to 2CH.
AJ-HPX2000P(VQT1D27-1)E.book 161 ページ ２００７年７月３０日 月曜日 午後１時３１分 PAINT RB GAIN CONTROL Items/ Adjustable Remarks Data Saved Range For setting the Rch gain when the R GAIN AWB –200 : WHITE BAL switch is in the PRST PRE +000 position. : z If the remote control unit is +200 connected, settings made from the menu are disabled. (The set value is displayed.
AJ-HPX2000P(VQT1D27-1)E.book 162 ページ ２００７年７月３０日 月曜日 午後１時３１分 MATRIX COLOR CORRECTION Items/ Adjustable Remarks Data Saved Range For selecting the color correction table MATRIX A for the linear matrix. TABLE B S C U F R For performing the linear matrix MATRIX R-G –63 : adjustment. (red/green) +00 : S C U F R +63 MATRIX R-B –63 : +00 : +00 : S C U F R +63 Mg –63 : (SAT) +00 For performing the linear matrix adjustment.
AJ-HPX2000P(VQT1D27-1)E.book 163 ページ ２００７年７月３０日 月曜日 午後１時３１分 LOW SETTING Items/ Adjustable Remarks Data Saved Range For performing the hue correction for R(PHASE) –63 : red. +00 : : S C U F R +63 R-Mg(PHASE) –63 : +00 For performing the hue correction between red and magenta. : +00 For performing the hue correction for magenta. +00 For performing the hue correction between magenta and blue. +00 For performing the hue correction for blue. : +00 20 DTL CORING 00 : 01 S C U F R 15 H.
AJ-HPX2000P(VQT1D27-1)E.book 164 ページ ２００７年７月３０日 月曜日 午後１時３１分 MID SETTING HIGH SETTING Items/ Adjustable Remarks Data Saved Range Select the master gain from –3, 0, 3, 6, MASTER –3dB : 9, 12, 15, 18, 21, 24, 27, or 30dB. GAIN 6dB : S C U F – 30dB H.DTL LEVEL 00 : 08 : For performing the horizontal detail correction level setting. : S C U F – 63 V.DTL LEVEL 00 : 18 For performing the vertical detail correction level setting.
AJ-HPX2000P(VQT1D27-1)E.book 165 ページ ２００７年７月３０日 月曜日 午後１時３１分 ADDITIONAL DTL Items/ Adjustable Remarks Data Saved Range For changing the detail level of the high KNEE APE OFF brightness portion. LVL 1 2 : S C U F R 5 DTL GAIN(+) –31 : +00 Adjust the detail level toward + (upwards). : S C U F R +31 DTL GAIN(–) –31 : +00 Adjust the detail level toward the – (downwards). : S C U F R +31 00 DTL CLIP : S C U F R 63 H.
AJ-HPX2000P(VQT1D27-1)E.book 166 ページ ２００７年７月３０日 月曜日 午後１時３１分 SKIN TONE DTL Items/ Adjustable Remarks Data Saved Range For selecting the skin color table for SKIN TONE OFF enabling the skin tone detail. A DTL The skin color table is provided in the B SKIN TONE TABLE item. AB By enabling the skin tone detail, it is possible to shoot human skin more accurately.
AJ-HPX2000P(VQT1D27-1)E.book 167 ページ ２００７年７月３０日 月曜日 午後１時３１分 KNEE/LEVEL GAMMA Items/ Adjustable Remarks Data Saved Range Set the master pedestal. MASTER PED –200 : +015 Items/ Adjustable Remarks Data Saved Range Set the master gamma in 0.01% steps. MASTER 0.30 : GAMMA 0.45 : S C U F R +200 ON MANUAL OFF KNEE S C U F R KNEE POINT 70.0% : 93.0% : Set the mode when the AUTO KNEE switch is OFF. The KNEE POINT/ SLOPE set value is enabled when this setting is ON.
AJ-HPX2000P(VQT1D27-1)E.book 168 ページ ２００７年７月３０日 月曜日 午後１時３１分 CAMERA SETTING Items/ Adjustable Remarks Data Saved Range For switching ON/OFF of the detail ON DETAIL signals. OFF S C U F R For specifying whether or not to enable 2D LPF ON or disable the 2-dimension LPF, which OFF reduce the cross color (for the SD mode only). Note In PAL mode, the 2-dimension LPF is disable. S C U F R HIGH COLOR ON OFF S C U F R ON GAMMA OFF S C U F R TEST SAW ON OFF S C U F R ON FLARE OFF S C U F R H-F COMPE.
AJ-HPX2000P(VQT1D27-1)E.book 169 ページ ２００７年７月３０日 月曜日 午後１時３１分 VF VF DISPLAY ZEBRA Pattern Display Items/ Adjustable Remarks Data Saved Range NORMAL: Display status constantly. NORMAL DISP HOLD: Display status only when the CONDITION HOLD MODE CHECK switch is pressed. – C U F R DISP MODE 1 2 3 – C U F R 0 VF DTL : 5 – C U F R ZEBRA1 0% : DETECT 70% For selecting the video signals to display in the viewfinder screen.
AJ-HPX2000P(VQT1D27-1)E.book 170 ページ ２００７年７月３０日 月曜日 午後１時３１分 VF MARKER VF USER BOX Items/ Adjustable Remarks Data Saved Range Select the VF MARKER setting table. A TABLE First, select table A or B, then set the B items below for each table. – C U F R Switch the center mark. CENTER OFF OFF: Do not display center mark. 1 MARK 1: + (large) 2 2: Hollow (large) 3 3: + (small) 4 4: Hollow (small) – C U F R Select the frame type for the safety SAFETY OFF zone. MARK 1 OFF: Do not display frame.
AJ-HPX2000P(VQT1D27-1)E.book 171 ページ ２００７年７月３０日 月曜日 午後１時３１分 VF INDICATOR1 Items/ Adjustable Remarks Data Saved Range For selecting ON or OFF for the EXTENDER ON extender display. OFF – C U F R Set the shutter speed indication to ON ON SHUTTER or OFF.
AJ-HPX2000P(VQT1D27-1)E.book 172 ページ ２００７年７月３０日 月曜日 午後１時３１分 !LED Items/ Adjustable Remarks Data Saved Range Select whether or not to enable “REC” REC STATUS ON indication in the viewfinder and on the OFF LCD monitor during recording. ON: REC indication enabled. OFF: REC indication not enabled. Note This option is useful when camerarecorder is used independently.
AJ-HPX2000P(VQT1D27-1)E.book 173 ページ ２００７年７月３０日 月曜日 午後１時３１分 CAM OPERATION CAMERA ID Items/ Adjustable Remarks Data Saved Range ¢¢¢¢¢¢¢ Setting 1 for the CAMERA ID recorded ID1 on color bars. Up to 10 characters are ¢¢¢ allowed for this setting. – C U F – ¢¢¢¢¢¢¢ Setting 2 for the CAMERA ID recorded ¢¢¢ on color bars. Up to 10 characters are allowed for this setting. – C U F – ID2 ¢¢¢¢¢¢¢ Setting 3 for the CAMERA ID recorded on color bars. Up to 10 characters are ¢¢¢ allowed for this setting.
AJ-HPX2000P(VQT1D27-1)E.book 174 ページ ２００７年７月３０日 月曜日 午後１時３１分 SHUTTER SELECT Items/ Adjustable Remarks Data Saved Range For setting the shutter speed for POSITION1 POSITION 1. SEL For 59.94 Hz 1/100 1/120 1/250 1/500 1/1000 1/2000 HALF For 50 Hz For 50 Hz 1/60 1/120 1/250 1/500 1/1000 1/2000 – C U F – HALF POSITION2 SEL For 59.94 Hz 1/100 1/120 1/250 1/500 1/1000 1/2000 HALF 1/60 1/120 1/250 1/500 1/1000 1/2000 – C U F – HALF For setting the shutter speed for POSITION 2.
AJ-HPX2000P(VQT1D27-1)E.book 175 ページ ２００７年７月３０日 月曜日 午後１時３１分 USER SW SW MODE USER2 SW INH S.GAIN DS.GAIN LINE MIX S.IRIS I.OVR S.BLK B.GAMMA D.ZOOM ATW Y GET DRS ASSIST C.TEMP AUDIO CH1 AUDIO CH2 REC SW RET SW PRE REC SLOT SEL – C U F R PC MODE Allocate the USER2 button. For descriptions of the functions, see [Assigning Functions to USER MAIN, USER1 and USER2 Buttons] (page 51). Items/ Adjustable Remarks Data Saved Range RET SW R.
AJ-HPX2000P(VQT1D27-1)E.book 176 ページ ２００７年７月３０日 月曜日 午後１時３１分 Items/ Adjustable Remarks Data Saved Range For selecting the method used to DS.GAIN OFF L/M/H release the digital super gain mode DS.GAIN (cumulative gain). L/M/H: The mode is released by making a change in the L/M/H switch position and the DS.GAIN switch (USER switch). DS.GAIN: The mode is released using only the DS.GAIN switch (USER switch). – C U F – D.
AJ-HPX2000P(VQT1D27-1)E.book 177 ページ ２００７年７月３０日 月曜日 午後１時３１分 USER SW GAIN Items/ Adjustable Remarks Data Saved Range ¢ Select whether or not to enable 30dB for S.GAIN SUPER GAIN. • 30 dB ¢: Enable. • : Disable. – C U F R 36 dB ¢ • – C U F R 42 dB ¢ • – C U F R 48 dB ¢ • – C U F R 10 dB: ¢ • – C U F R ¢ 12 dB: • – C U F R ¢ 15 dB: • – C U F R ¢ 20 dB: • – C U F R Select whether or not to enable 42dB for SUPER GAIN. ¢: Enable. • : Disable. Select whether or not to enable 48dB for SUPER GAIN.
AJ-HPX2000P(VQT1D27-1)E.book 178 ページ ２００７年７月３０日 月曜日 午後１時３１分 MAIN OPERATION BATTERY/P2CARD Items/ Adjustable Remarks Data Saved Range BATTERY PROPAC14 Select the battery to use. Remaining SELECT TRIMPAC14 capacity detection is also performed HYTRON50 according to the selected battery. HYTRON140 The variable range is changed by the DIONIC90 item settings selected on the [BATTERY DIONIC160 SETTING1] (page 179) and [BATTERY SETTING2] (page 180) menus.
AJ-HPX2000P(VQT1D27-1)E.book 179 ページ ２００７年７月３０日 月曜日 午後１時３１分 BATTERY SETTING1 Items/ Adjustable Remarks Data Saved Range ¢ Enable selection under BATTERY PROPAC14 SELECT. • ¢:Enable selection. •: Disable selection. Select auto or manual to set the NEAR AUTO END voltage. MANUAL AUTO: Set voltage automatically. MANUAL:Set voltage manually. When MANUAL is selected in the above 11.0 : menu, set the NEAR END voltage in 0.1 13.8 V steps.
AJ-HPX2000P(VQT1D27-1)E.book 180 ページ ２００７年７月３０日 月曜日 午後１時３１分 BATTERY SETTING2 Items/ Adjustable Remarks Data Saved Range ¢ Enable selection under BATTERY PAG L95 SELECT. • ¢:Enable selection. •: Disable selection. Select auto or manual to set the NEAR AUTO END voltage. MANUAL AUTO: Set voltage automatically. MANUAL:Set voltage manually. When MANUAL is selected in the menu 11.0 : above, set the NEAR END voltage in 0.1 13.5 V steps.
AJ-HPX2000P(VQT1D27-1)E.book 181 ページ ２００７年７月３０日 月曜日 午後１時３１分 MIC/AUDIO1 MIC LOWCUT OFF FRONT CH2 W.L. REAR – C U F – MIC LOWCUT OFF FRONT CH3 W.L. REAR – C U F – Items/ Adjustable Remarks Data Saved Range Select the microphone low cut filter for MIC LOWCUT OFF Input Channel 4. FRONT CH4 OFF: The microphone low cut filter is W.L. disabled for any input. REAR FRONT: The microphone low cut filter is enabled when the front microphone is selected. W.L.
AJ-HPX2000P(VQT1D27-1)E.book 182 ページ ２００７年７月３０日 月曜日 午後１時３１分 MIC/AUDIO2 TC/UB Items/ Adjustable Remarks Data Saved Range Select the phantom power supply for the FRONT MIC ON front microphone. OFF POWER – C U F – ON Select the phantom power supply for the REAR MIC rear microphone. OFF POWER When OFF is selected, no phantom power is supplied even if the REAR AUDIO CH1 or CH2 switch is set to +48.
AJ-HPX2000P(VQT1D27-1)E.book 183 ページ ２００７年７月３０日 月曜日 午後１時３１分 TCG SET HOLD ON OFF ON/OFF switching for the feature that always starts recording (when the power is turned ON again) the TCG value that was set before the power is turned OFF. PRESET REGEN For the first recording after the power is turned on, a P2 card is inserted and then switching from this P2 card to another recording-target P2 card is performed, select whether or not to regenerate the time code as the value on the new P2 card.
AJ-HPX2000P(VQT1D27-1)E.book 184 ページ ２００７年７月３０日 月曜日 午後１時３１分 FILE SD CARD READ/WRITE Items/ Adjustable Remarks Data Saved Range Select the file number to read out. 1 R.SELECT : – – – F – 8 Read out the data from the SD memory READ card. – – – – – 1 W.SELECT : – – – F – 8 WRITE – – – – – CARD CONFIG Select the file number to write in. Write the camera-recorder’s menu data to the SD memory card. Format the SD memory card.
AJ-HPX2000P(VQT1D27-1)E.book 185 ページ ２００７年７月３０日 月曜日 午後１時３１分 LENS FILE SCENE Items/ Adjustable Remarks Data Saved Range Select the lens file number. 1 FILE NO. : – – – F – 8 Read the lens file data. READ – – – – – Write the lens file data. WRITE – – – – – READ – – – – – WRITE RESET – – – – – TITLE READ Menu CARD FILE 1 : SELECT – – – F – 8 Create the scene file title. – – – – – LENS FILE CARD R/W Items/ Adjustable Data Saved Range Reset the scene file values to the initial values.
AJ-HPX2000P(VQT1D27-1)E.book 186 ページ ２００７年７月３０日 月曜日 午後１時３１分 MAINTENANCE SYSTEM CHECK LENS FILE ADJ Items/ Adjustable Remarks Data Saved Range ON/OFF switching for checking proper COLOR ON operation of the camera-recorder. OFF CHECK The RGB level in the area around the center of the screen is indicated in the viewfinder to show whether each signal is successfully communicated from the optical channel to the digital channel and processed. – – – – – LENS ADJ Items/ Adjustable Data Saved Range F2.
AJ-HPX2000P(VQT1D27-1)E.book 187 ページ ２００７年７月３０日 月曜日 午後１時３１分 DIAGNOSTIC1 DIAGNOSTIC2 Items/ Adjustable Remarks Data Saved Range Displays the version of the main CAMSOFT software for the camera microprocessor. MAIN – – – – – Display the table version. CAM TABLE – – – – – PULSE FPGA Items/ Adjustable Remarks Data Saved Range Display the software version for the SYSCON system control microprocessor. SOFT – – – – – LCD SOFT Displays the version of the program for driving the CCD.
AJ-HPX2000P(VQT1D27-1)E.book 188 ページ ２００７年７月３０日 月曜日 午後１時３１分 OPTION MENU OPTION Items/ Adjustable Remarks Data Saved Range Select whether or not to prohibit opening ENG ON the menu screen. OFF SECURITY ON: Menu screen cannot be opened. Please consult your distributor to release the setting. OFF: Menu screen can be opened. – – – – – FRAME RATE FRM RATE For setting the user bits to record when the video system is set to 24P or 24PA, MENU UB or when the recording format is set to 720P.
AJ-HPX2000P(VQT1D27-1)E.book 189 ページ ２００７年７月３０日 月曜日 午後１時３１分 Updating the firmware incorporated into the camera-recorder For the most up-to-date information on firmware, see the support page for P2 at the following Web site: https://eww.pavc.panasonic.co.jp/pro-av/ To update the firmware, confirm the version on AJ-HPX2000 by selecting MAINTENANCE > DIAGNOSTIC 1 and DIAGNOSTIC 2 screens from the menu, and then access the above Web site to download the firmware if necessary.
AJ-HPX2000P(VQT1D27-1)E.book 190 ページ ２００７年７月３０日 月曜日 午後１時３１分 Specifications General Operating humidity: Power supply: DC 12 V (11.0 V - 17.0 V) Power consumption: 36 W (Main unit only, with LCD monitor OFF) 43 W (With the SDI-IN and AVC-Intra option installed, LCD monitor ON) indicates safety information.
AJ-HPX2000P(VQT1D27-1)E.
AJ-HPX2000P(VQT1D27-1)E.book 192 ページ ２００７年７月３０日 月曜日 午後１時３１分 Input/output Unit GEN LOCK IN: MON OUT: VIDEO OUT : TC IN: TC OUT: DVCPRO/DV : SDI-IN : BNCa1, 1.0 VP-P, 75 h (This is available as VIDEO IN or the return video input connector, which can be switched in the menu.) BNCa1, 1.0 VP-P, 75 h BNCa1, 1.0 VP-P, 75 h (It can be switched among HD-SDI/SDSDI/Composite.) HD-SDI: 0.8 VP-P, 75 h (Compliant with the SMPTE292M/296M/299M standards) SD-SDI: 0.
AJ-HPX2000P(VQT1D27-1)E.book 193 ページ ２００７年７月３０日 月曜日 午後１時３１分 Software information for this product 1.Customer advisory: This product includes software licensed under the GNU General Public License (GPL) and GNU Lesser General Public License (LGPL); customers have the right to download, modify, and redistribute source code for this software. Descriptions of the GPL and LGPL are stored on the installation CD included with this camera-recorder. See the folder named \LDOC.
AJ-HPX2000P(VQT1D27-1)E.book 194 ページ ２００７年７月３０日 月曜日 午後１時３１分 Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
