01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ1 Operating Instructions Camera-Recorder Model No. P E AJ- Before operating this product, please read the instructions carefully and save this manual for future use.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ2 Read this first! (For AJ-HDX900P) CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ3 Read this first! (For AJ-HDX900E) $ DO NOT REMOVE PANEL COVERS BY UNSCREWING THEM. To reduce the risk of electric shock, do not remove the covers. No user serviceable parts inside. Refer servicing to qualified service personnel. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. WARNING: OTO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ4 Read this first! (For AJ-HDX900E) Attention/Attentie OBatteries are used for the main power source and memory back-up in the product. At the end of their useful life, you should not throw them away. Instead, hand them in as small chemical waste. OVoor de primaire voeding en het reservegeheugen van het apparaat wordt gebruikgemaakt van een batterij.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ5 Contents Chapter 1 General ..................................... 7 1-1 1-2 1-3 1-4 1-5 1-6 Features of the camera unit ......................... 7 Features of the VTR unit .............................. 8 Features of the Input/Output unit ................ 8 Other featuresa ............................................. 9 Dimensions drawing ..................................... 9 System configuration .................................
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ6 Contents (continued) 5-4 Audio input signal preparations ................ 86 5-4-1 5-4-2 5-4-3 When using the front microphone ................... 86 When using a wireless receiver ...................... 86 When using an audio component .................... 87 5-5 Mounting the unit on a tripod .................... 87 5-6 Attaching the shoulder belt ....................... 88 5-7 Adjusting the position of the shoulder pad ................................
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ7 Notes O The unit’s internal clock is not set to the correct date and time when shipped from the factory. Before using the unit, set the date and time. (Refer to page 42) 1 O When the unit is used for the first time, first adjust the white balance.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:33 PM ページ8 Chapter 1 General (continued) 1-2 Features of the VTR unit 1-3 Features of the Input/Output unit O DVCPRO HD-LP format system The VTR unit employs the DVCPRO HD-LP recording format. Using the latest compression technology, it achieves two times the economy of the conventional DVCPRO HD format.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ9 Chapter 1 General (continued) 1-4 Other features 1 O Single action shoulder pad slide function It is now possible to adjust the position where the unit is optimally balanced for operation using a single-touch action. This means that the operator can easily optimize the unit’s balance when the lens, battery, and other peripheral camera devices have been installed on the unit.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ10 Chapter 1 General (continued) 1-6 System configuration Microphone kit: AJ-MC900G UniSlot wireless microphone receiver: Sennheiser EK3041 Remote control unit: AJ-RC10G 2-inch electronic HD viewfinder: AJ-HVF21G (Mic holder provided) Battery PROPAC14, TRIMPAC14, HYTRON50/100/120, DIONIC90/100/160 Microphone holder: AJ-MH800G Lens (Bayonet type): Fujinon, Canon GPS unit: AJ-GPS900G (This unit is not available in European region.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ11 Chapter 2 Parts and their functions 2-1 Power supply and accessory mounting section ? 7 6 2 6 2 5 9 8 : 1 4 3 > 1 POWER switch This switch turns the power ON and OFF. 2 Battery mount This is for attaching the Anton/Bauer battery pack. 3 DC IN (external power input) socket (XLR, 4-pin) This unit is connected to an external DC power supply.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ12 Chapter 2 Parts and their functions (continued) 2-2 Audio function section (input system) =< > ; : 3 7 2 6 1 1 MIC IN (microphone input) jack (XLR, 5-pin) Connect the microphone (optional accessory) here. The power for the microphone is supplied from this jack. Components of 150 Hz are removed from the signals input from this connector.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ13 Chapter 2 Parts and their functions (continued) 2-2 Audio function section (output system) 9 AUDIO OUT connector (XLR, 5-pin) The audio signals recorded on audio channels 1 and 2 or audio channels 3 and 4 are output from this connector. The signals to be output can be selected using the MONITOR SELECT CH1/2OCH3/4 selector switch :.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ14 Chapter 2 Parts and their functions (continued) 2-3 Shooting and recording/playback function section 1 D 498 G 6 /REW EJECT H 5 FF/ STOP PLAY/PAUSE ª 1/; E F : 3 ; @ A 2 <567 ? > = J BC I Shooting and recording (camera unit) 1 CC FILTER/ND FILTER (filter switching) controls These are used to select the filter in accordance with the subject’s brightness and color temperature.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ15 Chapter 2 Parts and their functions (continued) 6 OUTPUT/AUTO KNEE selector switch This switch selects the video signals which are to be output from the camera unit to the VTR unit, viewfinder and/or video monitor. CAM. AUTO KNEE ON: The images shot by the camera are output. The AUTO KNEE circuit operates. CAM. AUTO KNEE OFF: The images shot by the camera are output. The MANUAL KNEE circuit operates. BARS: Color bar signals are output.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ16 Chapter 2 Parts and their functions (continued) = VIDEO OUT OUTPUT SEL (output signal selection) switch This is used to select the signals output from the VIDEO OUT connector. VTR : In the recording or other EE mode, the camera images are output from the connectors; in the playback mode, it is the VTR’s playback signals which are output. CAM : The camera images are output at all times.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ17 Chapter 2 Parts and their functions (continued) J DVCPRO connector This is an output connector for video, voice, and data that comply with the IEEE1394 standard. O It is impossible to input signals from external devices. O Power is not supplied from the unit. O Before proceeding to connect or disconnect the DV cable (IEEE1394), be absolutely sure to turn off the power of the units that are to be connected or disconnected using this cable.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ18 Chapter 2 Parts and their functions (continued) 2-5 Time code related section 4 5 6 9 1 3 2 1 GENLOCK IN connector (BNC) The HD Y reference signal is supplied to this connector when the camera unit is to be gen-locked or the time code is to be externally locked. It is also possible to supply composite video signals instead as the reference signal.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ19 Chapter 2 Parts and their functions (continued) 2-6 Warning/status display section 2-7 Display window and its displays Remaining tape and remaining battery charge and audio channel level displays 1 2 4 Remaining tape display The remaining tape time is displayed using 7 segments. The remaining tape time indicated by each segment is set to 3 minutes or 5 minutes using TAPE REMAIN/∫ on the VTR MENU “BATTERY/TAPE” screen.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ20 Chapter 2 Parts and their functions (continued) Mode displays GPS: GPS : P-REC: iREC: i: Lights when signals cannot be received during GPS operation. Lights when signals are being received during GPS operation. Lights in pre-recording mode and flashes during the time set for pre-recording after the tally lamp for recording has turned off. Lights during recording when the interval recording mode is established; flashes during recording standby.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ21 Chapter 2 Parts and their functions (continued) 2-8 Viewfinder section = > ;7 9 : < 1 8 452 3 6 ON OFF 1 Viewfinder (optional accessory) While recording or playback is underway, pictures can be viewed through the viewfinder in black and white. The warning displays concerning the unit’s operation statuses and settings, messages, zebra patterns and markers (safety zone markers and center marker) can also be seen in the viewfinder.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ22 Chapter 3 Recording and playback 3-1 Cassette tapes Checking for tape slack Loading a cassette tape Gently push in the reel using your finger and turn the reel in the direction of the arrow. If the reel fails to turn, it means there is no tape slack. 1 Set the POWER switch to ON. When condensation has formed inside the unit, the HUMID display lights. Wait until this display is cleared before proceeding with the intended operation.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ23 Chapter 3 Recording and playback (continued) 3-2 Basic procedures Up to performing the switch settings This section describes the basic steps for shooting and recording. Before actually departing to shoot scenes, carry out inspections to ensure that the system is functioning properly. * For details on how to perform these inspections, refer to “6-1 Inspections prior to shooting.” Provide the power supply, and load the cassette.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ24 Chapter 3 Recording and playback (continued) Procedure for shooting From adjusting the white balance and black balance to stopping the recording From adjusting the white balance and black balance to stopping the recording 1 Select the filter to match the lighting conditions. the white balance has been stored in the 2-1 Ifmemory ahead of time: Set the WHITE BAL switch to “A” or “B.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ25 Chapter 3 Recording and playback (continued) 3-3 Scene-to-scene continuity Maintaining continuity from one scene to the next at an accuracy of +1 frame or less can be assured simply by pressing the REC START button or VTR button on the lens while the unit is in the rec-pause mode. If the unit is in a mode other than rec-pause, the point at which the scene-to-scene continuity is to be maintained must be located before recording is started.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ26 Chapter 3 Recording and playback (continued) Transitions with the jump operation Recorded section D Section not recorded (B, C) Pause for replaying Pause for replaying No recorded section is available.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ27 Chapter 3 Recording and playback (continued) 3-5 Recording in intervals (INTERVAL REC function) iREC start This unit enables recording in intervals with a minimum recording time in increments of one frame, by using the builtin memory.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ28 Chapter 3 Recording and playback (continued) Frame-by-frame shooting Checkpoints common to all INTERVAL REC modes Procedure for shooting in the ONE SHOT mode ≥ Sound-related Whether the sound is to be recorded or not during interval recording is set by setting ON or OFF for the AUDIO REC item on the screen.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ29 Chapter 3 Recording and playback (continued) 3-6 To take the previous cut again (RETAKE function) The RETAKE function ensures continuity with the previous cut on the tape when shooting is resumed. It is set by opening the screen from the SYSTEM SETTING page and selecting ON as the setting for the RETAKE MODE item by performing menu operations. The RETAKE MODE item settings are described below.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ30 Chapter 4 Adjustments and settings for recording 4-1 Multi Format 4-1-1 Video system and Recording format The unit employs a progressive scan (full pixel reading) CCD system. It is possible to select 11 kinds of the recording formats by combinations of the SYSTEM MODE item and the CAMERA MODE item on the screen on the SYSTEM SETTING page in the setting menu. In any recording format, the CCD operates in progressive (non-interlace) scan mode.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ31 Chapter 4 Adjustments and settings for recording (continued) 4-1-2 Recording format on tapes and signal format at output connector The format for recording signals from CCD on tape and signal formats to be output from the respective connectors are shown below. Menu setting SYSTEM MODE item 1080-59.94i 1080-50i 720-59.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ32 Chapter 4 Adjustments and settings for recording (continued) In order to achieve images with a consistently high picture quality with this unit, it is necessary to adjust the black balance and white balance as the individual conditions demand. To achieve a higher picture quality, it is recommended that the adjustments be performed in the following sequence: AWB (white balance adjustment) > ABB (black balance adjustment) > AWB (white balance adjustment).
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ33 Chapter 4 Adjustments and settings for recording (continued) When there is no time to adjust the white balance Set the WHITE BAL switch to PRST. The white balance for the filter is achieved in accordance with the setting position of the FILTER control (outer). When the white balance cannot be adjusted automatically When the white balance adjustment was not completed correctly, one of the following error messages will appear on the viewfinder screen.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ35 Chapter 4 Adjustments and settings for recording (continued) 4-3 Setting the electronic shutter This section describes the unit’s electronic shutter, its settings and operations. To use the half shutter speed (HALF) O For shooting images when adding effects as if taken with film Video system CAMERA MODE Shutter speed 4-3-1 Shutter modes 1080-59.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ36 Chapter 4 Adjustments and settings for recording (continued) 4-3-2 Setting the shutter mode and speed The shutter speeds used in the shutter mode are set by switching the SHUTTER switch. The shutter speeds in the SYNCHRO SCAN mode can easily be changed using the SYNCHRO SCAN (+ and –) buttons on the side panel. Open the screen and screen from the OPERATION page by performing menu operations.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ37 Chapter 4 Adjustments and settings for recording (continued) 4-4 Selecting the audio input signals and adjusting their recording levels When the AUDIO SELECT CH1/CH2 switch is set to AUTO, the recording levels on audio tracks CH1 and CH2 are adjusted automatically. On the other hand, when it is set to MAN, the levels can be adjusted manually. The recording levels on audio tracks CH3 and CH4 can be selected using the menu.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ38 Chapter 4 Adjustments and settings for recording (continued) 4-4-3 CH3 and CH4 recording levels 4-5 Setting the time data Audio signals can be recorded separately for four audio channels. Perform menu operations to open the screen from the VTR MENU page to change the settings for the AUTO LEVEL CH3 and AUTO LEVEL CH4.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ39 Chapter 4 Adjustments and settings for recording (continued) 5 O To record the user bits of LTC, open the screen from the VTR MENU page by performing menu operations and select “USER” in the UB MODE item. (When the recording format is 720-50P or 72059.94P, set the OUTPUT/AUTO KNEE switch to the “BARS” position in order to record the user bits of LTC in a mode for recording built-in color bar signals.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ40 Chapter 4 Adjustments and settings for recording (continued) How to store the camera shooting information into user bits SYSTEM MODE/ CAMERA MODE 1080-59.94i 1080-50i 1080-59.94i 720-50P 720-59.94P User bits 60i 50i 30P 25P 60P 50P 30P 25P 24P User bits of VITC (or LTC) LTC UB Select “FRM RATE” in the UB MODE item. VITC UB Auto 24P 24PA When the recording format is 1080-50i or 1080-59.94i LTC UB Select “FRM RATE” in the UB MODE item.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ41 Chapter 4 Adjustments and settings for recording (continued) When the recording format is 720-50P or 720-59.94P VITC user bits LTC user bits O When the internal colour bar signals are being recorded User bits setting Tape management information LTC user bits verification information User bits setting Frame frequency 4: 50.00 Hz 5: 59.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ42 Chapter 4 Adjustments and settings for recording (continued) 4-5-2 Setting the internal clock’s date and time The unit’s internal clock is not set to the correct date and time when shipped from the factory. Before using the unit, set the date and time. 1 2 3 4 5 Set the DISPLAY switch to UB. Press the HOLD button to cause DATE to be displayed in the display window. Set the TCG switch to SET.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ43 Chapter 4 Adjustments and settings for recording (continued) 4-5-3 Setting the time code 4-5-4 Externally locking the time code 1 Set the DISPLAY switch to TC. 2 Set the TCG switch to SET. The unit’s internal time code generator can be locked to an external generator. In addition, the time code generator of an external VTR can be locked to the unit’s internal generator.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ44 Chapter 4 Adjustments and settings for recording (continued) Example 2: When connecting a multiple number of units and using one of them as the reference unit TC OUT MON OUT (HD-Y) or VIDEO OUT (VBS) Reference unit TC IN In the unit, there is a video signal delay in the camera, which is required or the process of converting video images taken with the image-shooting element from the progressive signals to the interlace signals.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ45 Chapter 4 Adjustments and settings for recording (continued) Example 4: When the unit and an external device are locked to the external time code generator, which is connected externally, and when several units of the camera are connected in a cascade configuration. Example 5: When an external device is locked to the time code generator of the unit.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ46 Chapter 4 Adjustments and settings for recording (continued) Example 6: When an external device is locked to the time code generator of this unit, which is connected in a cascade configuration. Reference video signal Operating procedure for external locking Follow the steps below for external locking. 1 Set the POWER switch to ON. 2 Set the TCG switch to F-RUN. 3 Set the DISPLAY switch to TC.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ47 Chapter 4 Adjustments and settings for recording (continued) When switching the power from the battery to an external power supply while the time code is externally locked In order to ensure the continuity of the time code generator’s power, connect the external power supply to the DC IN socket, and then remove the battery pack. If the battery pack is removed first, no guarantees can be made for the continuity of the external locking of the time code.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ49 Chapter 4 Adjustments and settings for recording (continued) 2 To increment the value Turn the JOG dial button to move the arrow (cursor) to the item which is to be set, and the sub menu screen appears when the JOG dial button is pressed. Turn the JOG dial button in the clockwise direction as viewed from the front of the camera.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ50 Chapter 4 Adjustments and settings for recording (continued) 4-7 Viewfinder screen status displays 4-7-2 Viewfinder screen status display configuration Not only the images but the lamps and characters indicating the unit’s settings and operation statuses as well as the messages, center and safety zone markers, camera ID and other information are displayed inside the viewfinder.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ51 Chapter 4 Adjustments and settings for recording (continued) Display item What is displayed Status when display appears 1080 720 This indicates the mode that the unit operates in. 1080 interlace mode 720 progressive mode 60i 30P 24P 24PA 50i 25P 60P 50P This indicates the video systems for recording signals output from the CCD on tape and outputting signals as HD SDI signals. 1080-59.94i 1080-29.97P or 720-29.97P 1080-23.98P or 720-23.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ52 Chapter 4 Adjustments and settings for recording (continued) Display item What is displayed (AUDIO: microphone power status) FRONT: ON/OFF REAR: ON/OFF This indicates the status of the front microphone’s power. This indicates the menu setting status for the rear microphone’s power. (AUDIO: channel input signals and levels) FRONT/W.L./REAR CH1/2/3/4 This indicates the input signals and levels for the individual channels.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ53 Chapter 4 Adjustments and settings for recording (continued) Display item What is displayed Status when display appears DRS “INH” is indicated when the operation of the USER button has been disabled. This indicates the value selected for S.GAIN. This indicates the value selected for DS.GAIN. This indicates whether LINE MIX GAIN is set to ON or OFF. This indicates whether S.IRIS is set to ON or OFF.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ54 Chapter 4 Adjustments and settings for recording (continued) Display item What is displayed Status when display appears E AUDIO input system and level meter ---- ∫---+ F W R This indicates the audio channels selected and their audio levels. This appears when the AUDIO IN switch is at the FRONT position. This appears when the AUDIO IN switch is at the WIRELESS position. This appears when the AUDIO IN switch is at the REAR position.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ55 Chapter 4 Adjustments and settings for recording (continued) Viewfinder screen display selection Whether a display is to be shown or not can be selected on a menu.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ56 Chapter 4 Adjustments and settings for recording (continued) 4-7-4 Display modes and setting changes/adjustment result messages #< VF DISPLAY > DISP CONDITION DISP MODE VF OUT VF DTL ZEBRA1 DETECT ZEBRA2 DETECT ZEBRA2 LOW LIGHT LVL RC MENU DISP.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ57 Chapter 4 Adjustments and settings for recording (continued) 3 When the JOG dial button is pressed, the arrow (cursor) moves to the ID input area, and the input mode is established. 4 Press the JOG dial button again and turn it until the character to be set is displayed.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ58 Chapter 4 Adjustments and settings for recording (continued) 4-8 Selection of video output signals The unit employs the VIDEO OUT connector and the MON OUT connector as connectors for outputting video signals. 4-8-1 Settings of signals output from VIDEO OUT connector The signal modes for outputting signals from the VIDEO OUT connector are switched with the VIDEO OUT switch.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ59 Chapter 4 Adjustments and settings for recording (continued) Set the marker and user boxes to superimpose on the output signals from the VIDEO OUT connector by using the respective items on the
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ60 Chapter 4 Adjustments and settings for recording (continued) 4-8-2 Settings of signals output from MON OUT connector Set the video signals output from the MON OUT connector by using the MONI OUT item on the menu (
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ61 Chapter 4 Adjustments and settings for recording (continued) 4-9 Menu-driven function setup 4-9-2 Selecting the F.AUDIO LEVEL control function The functions can be set up using the unit’s menus. 4-9-1 Setting the USER SW GAIN switching This unit allows three other modes to be used in addition to the L/M/H standard gain settings: the analog gain-up S.GAIN (super gain) mode to achieve a gain of 30 dB or more, the cumulative gain-up DS.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ62 Chapter 4 Adjustments and settings for recording (continued) 4-9-3 Allocating functions to the USER MAIN, USER1 and USER2 buttons The desired functions can be allocated to the USER MAIN, USER1 and USER2 buttons. To select this function, perform menu operations to open the screen from the OPERATION page, and set the desired function each with the USER MAIN SW item, USER1 SW item and USER2 SW item.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ63 Chapter 4 Adjustments and settings for recording (continued) 4-9-4 Setting the color temperature manually The white balance can be adjusted manually using the color temperature settings. The manual color temperature settings can be set independently for PRST, A, and B with the WHITE BAL switch.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ64 Chapter 4 Adjustments and settings for recording (continued) 4-10 Set data handling Set data file configuration The unit employs 5 sets for the file data area. FACTORY data: The area for storing factory settings Data cannot be revised with menu operations. USER data: The area for storing the data set by menu operations The FACTORY data is stored as the factory setting.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ65 Chapter 4 Adjustments and settings for recording (continued) 4-10-1 Handling the setup card 4-10-2 Setup card operations An SD memory card (optional accessory) can be used as a setup card that stores up to eight files of settings menu specifications. The setup card can be inserted or removed before or after the power is switched on. O The unit supports SD memory cards from 8 MB to 2 GB. O The SD memory card must be formatted using the unit.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ66 Chapter 4 Adjustments and settings for recording (continued) If one of the following messages appears when the JOG dial button is pressed, the card will not be formatted Remedial action Error message CONFIG NG NO CARD (setup card has not been inserted) Insert the card. CONFIG NG ERROR (the card cannot be formatted) The card may be defective. Replace it. CONFIG NG WRITE PROTECT Remove the card to cancel write protect.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ67 Chapter 4 Adjustments and settings for recording (continued) Saving the data settings to the selected file 9 the JOG dial button to move the arrow (cursor) to 13 Turn YES, and press the JOG dial button. When the data saving is completed, the following message appears. When the title has been input, turn the JOG dial button to move the arrow (cursor) to the “:” position. < CARD READ/WRITE > R.SELECT READ W.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ68 Chapter 4 Adjustments and settings for recording (continued) Loading the data of the selected file 4 Turn the JOG dial button to move the arrow (cursor) to the READ item. < CARD READ/WRITE > # R.SELECT READ W.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ69 Chapter 4 Adjustments and settings for recording (continued) 4-10-3 How to use the user data Loading the user data The setting data can be written in the user data area of the unit’s internal memory and data written in the memory can be read from this area. Use of this data speeds up the process of reproducing suitable setup statuses. 1 Perform a menu operation to open the screen.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ70 Chapter 4 Adjustments and settings for recording (continued) 4-10-4 How to use the scene file data 6 When the JOG dial button is pressed, the following message appears. The setting data can be written in the scene file area of the unit’s internal memory and the data written can be read from this area. Up to four scene files can be registered. By using this data, the appropriate setup statuses can be established speedily.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ71 Chapter 4 Adjustments and settings for recording (continued) Reading the setting data used for the scene files Returning the setting data used for the scene files to the factory settings 1 Perform a menu operation to open the screen. 1 Perform a menu operation to open the screen. 2 Turn the JOG dial button to move the arrow (cursor) to the SCENE SEL item.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ72 Chapter 4 Adjustments and settings for recording (continued) Appending titles to the setting data used for the scene files 8 When the JOG dial button is pressed, the arrow (cursor) returns to the TITLE1, 2, 3 or 4 item. Turn the JOG dial button to move the arrow (cursor) to the WRITE item. 1 Perform a menu operation to open the screen.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ73 Chapter 4 Adjustments and settings for recording (continued) 4-10-5 Method for returning to user settings 4-10-6 Method for returning to the factory settings It is possible to return the settings of the menu on the unit to the user settings that were registered previously in accordance with “4-10-3 How to use the user data.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ74 Chapter 4 Adjustments and settings for recording (continued) 4-10-7 Lens file The built-in memory of the unit stores eight sets of lens files. On the SD memory card, eight titles for eight sets of lens files in a table (total 64 sets) can be written. The following data are recorded on the lens file.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ75 Chapter 4 Adjustments and settings for recording (continued) 4-10-9 To save the lens file into the built-in memory Select the file No. 6 When the JOG dial button is pressed, the arrow (cursor) moves to the title input area, and the input mode is established. < LENS FILE > 1 Using the menu operations, open the screen from the FILE page.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ76 Chapter 4 Adjustments and settings for recording (continued) 11 When the JOG dial button is pressed, the arrow (cursor) returns to the TITLE: item. < LENS FILE > FILE SELECT READ WRITE RESET ALL :1 n TITLE:222222222222 1: 2: 3: 4: 5: 6: 7: 8: 12 Turn the JOG dial button to move the arrow (cursor) to the WRITE position.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ77 Chapter 4 Adjustments and settings for recording (continued) 4-10-10 To read the lens file from the builtin memory 1 Using menu operations, open the screen from the FILE page. 7 Turn the JOG dial button to move the arrow (cursor) to YES, and press the JOG dial button. The recorded data from the white shading file is read. 8 Press the MENU button twice.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ78 Chapter 4 Adjustments and settings for recording (continued) 4-10-11 To write in and read out the lens file to/from the SD memory card The contents of the eight lens files stored in the unit’s internal memory can be saved onto an SD memory card as card files under a single title. A total of eight titles can be saved on an SD memory card.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ79 Chapter 4 Adjustments and settings for recording (continued) Loading lens files from the SD memory card 1 Using menu operations, open the screen from the FILE page. 2 Turn the JOG dial button to move the arrow (cursor) to the CARD FILE SELECT item 4 3 Press the JOG dial button and the card file number will flash. Turn the JOG dial button to select the file (1 to 8) to be read.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ80 Chapter 5 Preparation 5-1 Supplying the power 5-1-1 Attaching the battery and setting the battery type A battery pack or an external DC power supply can be used as this unit’s power supply. Using the Anton/Bauer battery pack To use the battery pack, there is the following choice of makes of batteries: 1 Attach the battery pack made by Anton/Bauer.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ81 Chapter 5 Preparation (continued) Using the NP-1 type battery pack CAUTION: These servicing instructions are for use by qualified service personel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 1 Remove the battery holder. 2 Attach the NP-1 type battery case to the unit. 1 Tighten the mounting screws.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ82 Chapter 5 Preparation (continued) 5-1-2 Use of the external DC power supply 1 Connect the external DC power supply to the DC IN socket on the unit. DC IN socket External DC power supply 2 Turn “ON” the power switch of the external DC power supply. (If the power switch is available on the external DC power supply) 3 Turn ON the POWER switch on the unit. Rush current may occur at the time for turning on the power of the unit.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ83 Chapter 5 Preparation (continued) 5-2 Attaching the lens and adjusting the flange back Attaching the lens 1 Raise the lever for securing the lens, and detach the mount cap. Lever for securing the lens Adjusting the lens flange If the subject is not focused properly in the telephoto and wide-angle modes during zoom operations, adjust the flange back (distance from the lens mounting surface to the imageforming surface).
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ84 Chapter 5 Preparation (continued) 5-3 Adjusting the white shading of the lens 7 ≥ The zebra pattern will not cover the whole screen if there is any unevenness in the lighting. In this case, make adjustments to the position of the lighting, etc. ≥ Make adjustments to the position of the lighting, etc. also when the lens aperture is not between F4 and F10. ≥ Be absolutely sure to leave the electronic shutter at OFF.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ85 Chapter 5 Preparation (continued) the lens is provided with an extender, turn on the 11 When extender function, and repeat steps 7 to 9. (Once the extender function is turned on, the set values shown on the menu screen change.) The adjustment values of the two resulting patterns–one when the lens extender is provided and the other when it is not provided–are stored in the unit as the data of one lens file.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ86 Chapter 5 Preparation (continued) 5-4 Audio input signal preparations 5-4-2 When using a wireless receiver Prepare to connect the audio components which will supply the audio signals to the unit. When using a UniSlot wireless receiver 1 Remove the slot cover, insert the wireless receiver, and screw it down. 2 Set the AUDIO IN switches to WIRELESS for the audio channels whose audio signals are to be recorded.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ87 Chapter 5 Preparation (continued) 5-4-3 When using an audio component 5-5 Mounting the unit on a tripod 1 Connect the AUDIO IN connectors on the camera with the audio component using the XLR cable. Use the tripod adapter (SHAN-TM700) to mount the unit on a tripod. 2 Set the AUDIO IN switch or switches for the channel or channels to which the audio component has been connected to “REAR.” 3 1 Mount the tripod adapter on the tripod.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ88 Chapter 5 Preparation (continued) 5-6 Attaching the shoulder belt Shoulder belt 5-8 Attaching the rain cover Example showing use of the SHAN-RC700 rain cover The tab opens when it is pressed. Tighten the cord. To disengage the shoulder belt, press the tabs. Check that the shoulder belt is attached securely. 5-7 Adjusting the position of the shoulder pad The shoulder pad can be moved while the slide lever is held down.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ89 Chapter 5 Preparation (continued) 5-10 Connection of the remote control unit (AJ-RC10G) 5-11 Connection of the external switch It is possible to control some of the functions remotely by connecting the remote control unit AJ-RC10G (optional accessory). When AJ-RC10G is connected to the REMOTE connector on the unit and the power switches of both of the unit and AJRC10G are turned on, the unit automatically enters the remote control mode.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ90 Chapter 6 Maintenance and inspections 6-1 Inspections prior to shooting 6-1-2 Inspecting the camera unit Before setting off for a shooting session, perform the following inspections to verify that the system is functioning correctly. It is recommended that a color video monitor be used to check the images. 1 Set the zoom to the motorized zoom mode, and check its operations in this mode.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ91 Chapter 6 Maintenance and inspections (continued) 6-1-3 Inspecting the VTR unit 2. Automatic audio level adjustment function inspection Perform all the steps outlined in section “1. Tape travel inspection” through section “4. Earphone and speaker inspection” one after the other. 1 Set the AUDIO SELECT CH1 and CH2 switch to AUTO. 2 Set the AUDIO IN CH1 and CH2 switches to FRONT. 1.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ92 Chapter 6 Maintenance and inspections (continued) 5. Inspection using external microphones 1 Connect external microphones to the AUDIO IN CH1 and CH2 jacks. 2 Set the AUDIO IN CH1 and CH2 switches to REAR. 3 Set the LINE/MIC/+48V selector switch on the back panel to MIC or +48V in accordance with the external mic’s power supply type.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ93 Chapter 6 Maintenance and inspections (continued) 6-2 Maintenance 6-2-5 Replacing the backup battery 6-2-1 Condensation The backup battery is already installed when the unit is shipped. When it has discharged, the “BACK UP BATT EMPTY” display appears for 3 seconds on the viewfinder screen when the POWER switch is set to ON.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ94 Chapter 6 Maintenance and inspections (continued) 6-2-6 Connectors and signals 1 2 3 4 DC IN GND NC NC +12V Matsushita part number K1AA104H0038 Maker part number HA16RX-4P (SW1) (Hirose Denki) 1 2 3 AUDIO IN GND AUDIO IN(H) AUDIO IN(C) Matsushita part number K1AB103A0011 Maker part number HA16PRM-3SG (Hirose Denki) 3 2 1 2 Ensure that the polarities are used correctly for a power supply from an external source.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ96 Chapter 6 Maintenance and inspections (continued) Maker part number LENS 1 2 RET-SW REC-START/STOP ON/OFF of the return video RETURN ON: GND RETURN OFF: OPEN Control for recording start/stop +5 V HR10A-10R-12SC(71) (Hirose Denki) 9 1 10 8 2 11 12 7 6 3 4 5 0V START STOP START 3 GND GND 4 IRIS-AUTO ON/OFF of the forced iris servo SERVO ON: +5 V ±0.5 V SERVO OFF: OPEN 5 IRIS-CONT Control output for the lens iris F2.8: –6.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ98 Chapter 6 Maintenance and inspections (continued) 6-3 Warning system 6-3-1 Warning description tables When an error or a problem is detected immediately after the power is turned on or while an operation is underway, the WARNING lamp and lamps inside the viewfinder serve to alert the user. Items are displayed in the following sequence of priority: WARNING lamp > tally lamp > warnings inside the viewfinder.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ99 Chapter 6 Maintenance and inspections (continued) 6. SERVO 9. BATTERY NEAR END Indications on LCD screen “SERVO” display lights (during recording and playback). Indications on LCD screen The bar display that shows the remaining battery charge starts flashing. WARNING lamp Flashes four times a second (during recording and playback). WARNING lamp Flashes once a second. Tally lamp Flashes once a second. Viewfinder BATT LED starts flashing.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ100 Chapter 6 Maintenance and inspections (continued) 6-3-2 Error codes One of the following error codes appears in the display window when an error has occurred in the unit for some reason. When an error code appears, consult your dealer. Code No.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ101 Chapter 7 Menu description tables 7-1 Menu configuration MENU USER MENU MAIN MENU Items selected in SYSTEM SETTING PAINT OPTION MENU OPTION RB GAIN CONTROL RGB BLACK CONTROL MATRIX COLOR CORRECTION LOW SETTING MID SETTING HIGH SETTING ADDITIONAL DTL SKIN TONE DTL KNEE/LEVEL GAMMA CAMERA SETTING VF OPERATION How to open the menus USER MENU: Press MENU button to display.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ102 Chapter 7 Menu description tables (continued) 7-2 SYSTEM SETTING 7-2-1 SYSTEM MODE Variable range Item Item Variable range Remarks REC TIME For 59.94 Hz 00s01f : SYSTEM MODE For AJ-HDX900E For AJ-HDX900P 1080-50i 1080-59.94i 720-50P 720-59.94P C U F CAMERA MODE For AJ-HDX900E For AJ-HDX900P (1080-50i) 50i 25P (1080-59.94i) 60i 30P 24P 24PA (720-50P) 50P 25P (720-59.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ103 Chapter 7 Menu description tables (continued) 7-2-3 OUTPUT SEL Item OUTPUT ITEM Variable range MENU ONLY TC STATUS C U F MONI OUT HD-SDI HD-Y C U F MONI OUT CHARA ON OFF C U F MONI OUT MODE C U F Remarks For setting the characters superimposed on the output signals from the VIDEO OUT connector. MENU ONLY: The menu screen is superimposed only when the menu is accessed. This normally displays nothing.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ104 Chapter 7 Menu description tables (continued) 7-2-5 MONITOR OUT SETTING Variable range Item MONI OUT CENTR MARK OFF 1 2 3 4 For setting the center marker to be superimposed on the HD SDI output signals of the MON OUT connector. OFF: The center marker is not displayed.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ105 Chapter 7 Menu description tables (continued) 7-2-7 DOWNCON SETTING Variable range Item DOWNCON MODE 7-2-8 GENLOCK Remarks Variable range Item SQUEEZ LT-BOX S-CROP For setting the mode of the down converter output signals. ON OFF For setting the detail function for the down converter output signals ON/OFF. The down converter output signals contain detailed components that are set during HD signal processing.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ106 Chapter 7 Menu description tables (continued) 7-2-9 OPTION MODE Variable range Item REC TALLY RED GREEN CHAR For selecting the method to access records on the unit when the unit is connected to peripheral devices and used remotely. RED: The red tally lamp lights. GREEN: The green tally lamp lights. CHAR: For displaying “REC” in the viewfinder.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ107 Chapter 7 Menu description tables (continued) 7-3 PAINT 7-3-1 RB GAIN CONTROL Variable range Item R GAIN AWB PRE –200 : +000 : +200 S C U F R B GAIN AWB PRE –200 : : +200 S C U F R –200 : +000 : +200 S C U F R B GAIN AWB A –200 : : +200 S C U F R –200 : +000 : +200 S C U F R B GAIN AWB B –200 : : +200 S C U F R S C U F R For setting the Bch gain when the WHITE BAL switch is in the PRST position.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ108 Chapter 7 Menu description tables (continued) 7-3-3 MATRIX Variable range Item ∫ MATRIX TABLE A B 7-3-4 COLOR CORRECTION Remarks For selecting the color correction table for the linear matrix. Variable range Item R (SAT) –63 : +00 Remarks For performing correction of red. the color saturation : S C U F R MATRIX R-G –63 : +00 For performing the linear matrix adjustment.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ109 Chapter 7 Menu description tables (continued) 7-3-5 LOW SETTING Variable range Item R (PHASE) –63 : Remarks For performing the hue correction for red. ∫ MASTER GAIN +00 S C U F R : +00 Mg (PHASE) For performing the hue correction between red and magenta. : Mg-B (PHASE) : DTL CORING : For performing the hue correction between magenta and blue. 00 : 01 00 : : For performing the hue correction for blue.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ110 Chapter 7 Menu description tables (continued) 7-3-6 MID SETTING Variable range Item ∫ MASTER GAIN –3dB : 6dB S C U F R H.DTL LEVEL S C U F R S C U F R S C U F R 00 : S C U F R For performing the correction level setting. horizontal detail 00 : 06 S C U F R For performing the vertical detail correction level setting. : : 00 : S C U F R For performing the noise elimination level setting for detail.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ111 Chapter 7 Menu description tables (continued) 7-3-8 ADDITIONAL DTL Variable range Item KNEE APE LVL OFF 1 2 Remarks For changing the detail level of the high brightness portion. : 5 S C U F R DTL GAIN(+) –31 : +00 For changing the + direction level of the detail. : S C U F R DTL GAIN(–) +31 –31 : +00 For changing the – (below) direction level of the detail.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ112 Chapter 7 Menu description tables (continued) 7-3-9 SKIN TONE DTL Variable range Item ∫ SKIN TONE DTL OFF A B AB S C U F R ∫ SKIN TONE ZEBRA VF ON OFF S C U F R ∫ SKIN TONE ZEBRA VOUT Remarks For selecting the skin color table for enabling the skin tone detail. The skin color table is provided in the SKIN TONE TABLE item. By enabling the skin tone detail, it is possible to shoot human skin more accurately.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ113 Chapter 7 Menu description tables (continued) 7-3-10 KNEE/LEVEL Variable range Item MASTER PED –200 : +015 S C U F R ∫ MANUAL KNEE Remarks For performing the MASTER PEDESTAL setting. Variable range Item MASTER GAMMA : 0.75 ON OFF 70.0% : S For setting the mode which is to be established when the AUTO KNEE switch is at OFF. The KNEE POINT/SLOPE setting value is active when ON is selected.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ114 Chapter 7 Menu description tables (continued) 7-3-12 ∫ CAMERA SETTING Item DETAIL S C U F R HIGH COLOR S C U F R GAMMA S C U F R TEST SAW S C U F R FLARE S C U F R H-F COMPE. S C U F R Variable range Remarks ON OFF For switching ON/OFF of the detail signals. ON OFF For switching ON/OFF of the enlarging the color dynamic range. ON OFF For switching ON/OFF of the gamma correction. ON OFF For switching ON/OFF of the test signals.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ115 Chapter 7 Menu description tables (continued) 7-4 VF 7-4-1 VF DISPLAY Variable range Item DISP CONDITION NORMAL HOLD NORMAL: The statuses are displayed at all times. HOLD: The statuses are displayed only when the MODE CHECK switch is pressed. 1 2 3 For setting the display mode. This sets what is displayed in the viewfinder screen when the state of the unit is changed.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ116 Chapter 7 Menu description tables (continued) 7-4-2 VF MARKER Variable range Item TABLE A B C U F R CENTER MARK OFF 1 2 3 4 C U F R SAFETY MARK OFF 1 2 7-4-3 VF USER BOX Remarks For selecting the VF MARKER setting table. This item is used to set the current values of table A or B which have been selected using the menu items listed below. For selecting the center marker. OFF: The center marker is not displayed.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ117 Chapter 7 Menu description tables (continued) 7-4-4 VF INDICATOR1 Item EXTENDER C U F R SHUTTER C U F R FILTER C U F R WHITE C U F R GAIN Variable range TAPE ON OFF For selecting ON or OFF for the shutter speed display. BATTERY ON OFF For selecting ON or OFF for the filter No. display. AUDIO LVL ON OFF For selecting ON or OFF for the AWB PRE/A/B display. TC ON OFF For selecting ON/OFF of the gain currently selected, S.GAIN, DS.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ118 Chapter 7 Menu description tables (continued) 7-4-6 MODE CHECK IND Item STATUS Variable range 7-4-7 !LED Remarks ON OFF For the setting to display the status screen when the MODE CHECK button is pressed. ON OFF For the setting to indicate causes for turning on the lamp on the viewfinder is displayed when the MODE CHECK button is pressed. The causes for turning on the lamp are displayed with ! .
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ119 Chapter 7 Menu description tables (continued) 7-5 OPERATION 7-5-1 CAMERA ID Item ID1: 7-5-3 SHUTTER SELECT Variable range ********** Remarks CAMERA ID setting 1 C U F ID2: ********** CAMERA ID setting 2 ********** CAMERA ID setting 3 Item POSITION1 SEL For 59.94 Hz C U F ID3: C U F If READ FACTORY DATA is selected, this setting will be cleared.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ120 Chapter 7 Menu description tables (continued) 7-5-4 USER SW Item POSITION4 SEL For 59.94 Hz For 50 Hz C U F R POSITION5 SEL For 59.94 Hz For 50 Hz C U F R POSITION6 SEL For 59.94 Hz For 50 Hz C U F R Variable range 1/100 1/120 1/250 1/500 1/1000 1/2000 HALF Remarks For setting POSITION 4. the shutter Item speed for 1/60 1/120 1/250 1/500 1/1000 1/2000 HALF 1/100 1/120 1/250 1/500 1/1000 1/2000 HALF C U F R For setting POSITION 5.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ121 Chapter 7 Menu description tables (continued) 7-5-5 SW MODE Item RET SW Variable range R.REVIEW CAM RET C U F R S.BLK LVL C U F R AUTO KNEE SW ON OFF For selecting ON/OFF of the AUTO KNEE function. When it is set to OFF, the AUTO KNEE may not function even if the AUTO KNEE switch is turned ON. ON OFF SMPTE FULL BARS SPLIT ARIB L/M/H S.GAIN C U F DS.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ122 Chapter 7 Menu description tables (continued) 7-5-7 USER SW GAIN Item S.GAIN 30 dB Variable range 2 O C U F R 36 dB 2 O C U F R DS.GAIN 6 dB: 2 O C U F R 10 dB: 2 O C U F R 12 dB: 2 O C U F R 15 dB: C U F R Remarks A.IRIS LEVEL For selecting whether or not to enable a setting of 36 dB for SUPER GAIN. 2 : The 36 dB setting is enabled. O : The 36 dB setting is disabled. A.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ123 Chapter 7 Menu description tables (continued) 7-6 FILE 7-6-1 CARD READ/WRITE Variable range Item R.SELECT 1 : 8 7-6-3 LENS FILE Remarks FILE SELECT : 8 WRITE For reading the data from the SD memory card. READ For reading the data from the lens file. For selecting the number of the file in which the data is to be written. WRITE For writing the data in the lens file. RESET ALL For resetting the data of the lens file.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ124 Chapter 7 Menu description tables (continued) 7-7 MAINTENANCE 7-6-6 INITIALIZE Item Variable range 7-7-1 SYSTEM CHECK Remarks READ FACTORY DATA For returning the state of the unit to factory settings. Data returned to factory settings O User data O Scene file Data not returned to factory settings O Lens file O Black shading O White shading WRITE USER DATA The menu data that is inherent to the user are saved in user data memory on the unit.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ125 Chapter 7 Menu description tables (continued) 7-7-6 LENS FILE ADJ 7-7-4 BLACK SHADING Variable range Item CORRECT C U F R DETECTION (DIG) Remarks ON OFF For selecting ON or OFF for the digital black shading compensation. – For executing the digital black shading compensation.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ126 Chapter 7 Menu description tables (continued) 7-8 VTR MENU 7-8-1 VTR FUNCTION Item HUMID OPE Variable range Remarks Item ON OFF For selecting whether or not to continue operation when HUMID alarm state has occurred. ON: Operation continues until tape slack is detected even when the HUMID alarm state has occurred during operation. OFF: Operation is stopped as soon as the HUMID alarm state occurs.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ127 Chapter 7 Menu description tables (continued) 7-8-3 BATTERY SETTING1 Variable range Item PROPAC14 15.0 15.0 AUTO MANUAL For selecting how the voltage at which the battery charge is considered nearly depleted is to be set. AUTO: The voltage is set automatically. MANUAL: The voltage is set manually. For selecting the voltage at which the battery charge is to be considered nearly depleted in 0.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ128 Chapter 7 Menu description tables (continued) 7-8-4 BATTERY SETTING2 Variable range Item ENDURA10 2 O For enabling or disabling the selection made for the BATTERY SELECT item. 2 : The selection is enabled. O : The selection is disabled. AUTO MANUAL For selecting how the voltage at which the battery charge is considered nearly depleted is to be set. AUTO: The voltage is set automatically. MANUAL: The voltage is set manually. 11.0 : 13.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ129 Chapter 7 Menu description tables (continued) 7-8-5 MIC/AUDIO1 Item FRONT VR CH1 C U F FRONT VR CH2 C U F MIC LOWCUT CH1 C U F MIC LOWCUT CH2 C U F MIC LOWCUT CH3 C U F MIC LOWCUT CH4 C U F LIMITER CH1 C U F LIMITER CH2 C U F AUTO LEVEL CH3 Variable range Remarks OFF FRONT W.L. REAR ALL For setting whether or not to make the audio control operational for the input system selected for CH1. OFF FRONT W.L.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ130 Chapter 7 Menu description tables (continued) 7-8-7 TC/UB Item TC MODE Variable range DF NDF C U F UB MODE USER TIME DATE EXT TCG FRM RATE REGEN C U F VITC UB MODE C U F USER/EXT TIME DATE TCG FRM RATE REGEN Remarks For selecting the mode advancing the time code. DF: Drop frame NDF: Non-drop frame When the system frequency is set to 50 Hz, the mode is the non-drop frame mode. For selecting the users bits to record in the LTC area.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ131 Chapter 7 Menu description tables (continued) 7-9 OPTION MENU 7-9-1 OPTION 7-8-8 UMID SET/INFO Item COUNTRY Variable range NO-INFO For inputting the name of the user’s country. “NO-INFO” is displayed until this is input. NO-INFO For inputting the name of the user’s organization or company. “NO-INFO” is displayed until this is input. NO-INFO For inputting the user’s name. “NO-INFO” is displayed until this is input.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ132 Chapter 8 Specifications [GENERAL] Power supply: DC 12 V (DC 11.0 V - 17.0 V) Power consumption: 36 W indicates safety information. Ambient operating temperature: 0°C to +40°C (32°F to 104°F) Storage temperature: –20°C to +60°C (–4°F to 140°F) Ambient operating humidity: Within 10% to 85% (relative humidity) Continuous operation time: Approx. 120 min.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ133 Chapter 8 Specifications (continued) Audio System Time Code Input Connector Sampling frequency: 48 kHz (synchronized with video) Quantizing: 16 bits Frequency response: 20 Hz to 20 kHz ±1.0 dB (at 1 kHz, reference level) Dynamic range: Better than 85 dB (at 1 kHz, AWTD) Distortion: Less than 0.1% (at 1 kHz, reference level) Wow and flutter: Below measurable limits Head room: For AJ-HDX900P: 20 dB For AJ-HDX900E: 18 dB TC IN (BNC): 0.
01.AJ-HDX900_P_E(VQT0X86-1)_E 06.10.19 3:34 PM ページ134 Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
