Panasonic Broadcast AJ-HD1800p Menu Information
System menus No./Item Description of setting 05 For setting whether to perform the various adjustments for the video output signals using this VTR or using an external encoder remote controller. 0000 REMOTE The various adjustments for the video output signals are performed by an external encoder remote controller. 0001 LOCAL The various adjustments for the video output signals are performed using this VTR.
System menus No./Item 12 SYS H (continued) Description of setting For adjusting the HD SDI output system phase in 13.5nS steps. j: To advance the phase. i: To delay the phase.
System menus No./Item 20 AV PHASE (continued) Description of setting For adjusting the phase of the AUDIO output with the VIDEO output 20.8 microsecond steps The phase of audio output advances with respect to image output. The phase of audio output delays with respect to image output. 0000 : 0100 : 0200 For selecting the system frequency. SYSTEM 0000 59/60 The 59.94 Hz or 60 Hz system frequency is selected. 0001 50i/25P*2 The 50 Hz or 25 PsF system frequency is selected.
Setup menus No./Item 000 P-ROLL TIME 001 LOCAL ENA 002*1 TAPE TIMER 003 REMAIN SEL *1 Description of setting For setting the preroll time. Any time from 0 to 30 seconds can be set in 1-second increments. 0000 0s : : 5s 0005 : : 0030 30s z During automatic editing (PREVIEW or AUTO EDIT), no operations are performed if the preroll time is set to 0 seconds. z If the phases are to be synchronized between two decks for editing as per the setup menu item No.
Setup menus (continued) (continued) No./Item 007 CHARA H-POS 008 CHARA V-POS 009 CHARA TYPE 010*1 MONI CONTROL Description of setting For setting the character position in the horizontal direction for superimposed indications, such as time codes for HD SDI MONITOR/SD SDI MONITOR/VIDEO OUT3 connectors and superimposed indications from the IEEE 1394 digital interface.
Setup menus (continued) (continued) No./Item 022 Description of setting For selecting the format in which the tape is to be played back. PB FORMAT 023 FORMAT SEL 030*1 HD FREQUENCY 0000 MANU The format is determined by the setting selected for setup menu item No.023 (FORMAT SEL). 0001 AUTO1 The unit follows the format recorded on the tape. Whenever the format is changed during playback, the playback format switches to others according to the changed format.
Setup menus (continued) (continued) Formats in which the tape is played back 022: PB FORMAT MANUAL 020: SYS FORMAT 1080i 720p AUTO -------- 023: FORMAT SEL HD_LP HD_SP 50M 25M DV DVCAM HD_LP HD_SP 50M 25M DV DVCAM -------- Playback format DVCPRO HD-LP(1080i) DVCPRO HD(1080i) DVCPRO50(422) DVCPRO(411) DV DVCAM DVCPRO HD-LP(720p) DVCPRO HD(720p) DVCPRO50(422) DVCPRO(411) DV DVCAM DVCPRO HD-LP(1080i)/ DVCPRO HD(1080i)/ DVCPRO HD-LP(720p)/ DVCPRO HD(720p)/ DVCPRO50(422)/ DVCPRO(411)/ DV/DVCAM,
Setup menus (continued) No./Item Description of setting No./Item 100 For selecting the direct search dial operation. 106 SEARCH ENA 0000 DIAL Direct search dial operations are performed. 0001 KEY Unless the search button is pressed, the mode does not change to the search mode. For selecting the maximum speed of shuttle operations. EJECT EE SEL 101 SHTL MAX 0000 x9.8 k9.
Setup menus (continued) (continued) No./Item 111*1 MEMORY STOP 112 FRZ MODE SEL Description of setting For selecting whether to automatically stop the VTR when the counter value is at the “0” position during CTL mode FF and REW operations. 0000 OFF The VTR does not stop. 0001 ON The VTR is automatically stopped. z Either the stop or still picture (SHTL STILL or SLOW STILL) mode, whichever has been set using setup menu item No.307 (AFTER CUEUP), is established when the VTR is stopped.
Setup menus (continued) (continued) No./Item 118* 1 SP MODE INH 119*1 CONFI REC 131 PAGE MODE 132 ROTA MODE 133 KEY BEEP 134 ALARM BEEP Description of setting For selecting whether to allow or inhibit recording on a tape which has been written by a format other than DVCPRO HD-LP. 0000 OFF Recording on the cassette tape is allowed. 0001 ON Recording on the cassette tape is inhibited.
Setup menus (continued) No./Item 200 PARA RUN 202 ID SEL 204 RS2323C SEL 205 Description of setting For selecting whether to operate two or more VTRs in synchronization. 0000 DIS The VTRs are not operated in synchronization. 0001 ENA The VTRs are operated in synchronization. To operate the VTRs in synchronization, set all the VTRs to 1 (ENA). (Refer to page 16.) For setting what ID information is to be returned to the controller.
Setup menus (continued) No./Item 300 IN/OUT DEL 301 NEGA FLASH 302*1 CONFI EDIT 303*1 AUD EDIT IN 304*1 AUD EDIT OUT 305 AUTO ENTRY 306*1 CF ADJ SEL 307 AFTER CUE-UP Description of setting For selecting the operation to be performed when an edit point has been set incorrectly (when the OUT point comes before the IN point). 0000 MANU Editing is not performed unless the illegal edit point is cleared or set properly.
Setup menus (continued) (continued) No./Item 313 CLICK POINT 320*1 EDIT RPLCE1 321*1 EDIT RPLCE2 322*1 EDIT RPLCE3 Description of setting When the search dial from intermediate position turning to the right or the left with SLOW mode, the speed in the click point is set. 0000 ±1 i/j1 time speed 0002 ±1.85 i/j1.85 time speed (i1.85/j1.
Setup menus (continued) No./Item 400 STILL TIMER 401 SRC PROTECT 402 Description of setting For selecting the duration of the time taken after the VTR is left standing in the STOP or search STILL mode (JOG, SLOW or SHTL) before the tape protection mode is established. (Units: s = seconds, min = minutes) 0000 0.
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued)
Setup menus (continued) No./Item DIF SPEED 882*1 DIF IN CH 883*1 DIF OUT CH 886*1 DIF CONFIG 890*1 DIF AUD OUT 891*1 DIF DV AUDIO *1 Description of setting For setting the transfer speed of the IEEE1394 digital interface output. 880*1 0000 S100 100Mbps 0001 S200 200Mbps 0002 S400 400Mbps When S100 has been selected as this item’s setting, DVCPRO HD format signals cannot be input or output. For setting the input channel.
Setup menus (continued)
Setup menus (continued) Follow the steps below to switch the system frequency [59/60 Hz, 50 Hz, 23/24 Hz, 25 Hz (HD) or 25 Hz (SD), 50 Hz(HD), 50 Hz(SD)]. 1 Following the procedure for the (page 62) to change the system menu item No.25 (SYSTEM FREQ) setting. 2 Press F5 (SET) to enter the setting, and after the function menu shown on the time code display area has been cleared, the following message appears.
Setup menus (continued)
Setup menus NO. (continued) Menu item System menu No.25 (SYSTEM FREQ) 59/60 23/24 50i/25P 25 (HD) 25 (SD) 50 (HD) 50 (SD) No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No 015 AUTO STEP 020 SYS FORMAT No 022 PB FORMAT 023 FORMAT SEL 030 HD FREQUENCY 031 OUT REF No No 100 SEARCH ENA 101 SHTL MAX 102 FF.
Setup menus NO.
Setup menus NO. (continued) Menu item System menu No.
Setup menus NO. (continued) Menu item System menu No.
