Panasonic Broadcast AJ-HD1400p Menu Information
Setup (initial settings) This unit’s main settings can be performed and checked using the on-screen menus which are displayed on the video monitor connected to the unit. It is also possible to set and confirm using the item number and the setting number or the item name, which are displayed on the display part on the front panel. Furthermore, a user setting memory in which to store three sets of settings is provided, enabling the desired settings to be stored for future use.
Setup (initial settings) (continued) 3 Setting the user defaults Incline the joystick up and down to adjust the cursor in the default settings screen to the “LOAD” position and press the joystick. The mode for this unit changes to the LOAD mode, the LOAD screen is displayed on the video monitor, and the item name is displayed in the counter display.
Setup (initial settings) (continued) 6 Confirmation screen for SAVE is displayed. z When the PLAY button is pressed, the set value is stored and the display returns to the menu screen. z When the STOP button is pressed, the display returns to the menu screen without storing the set value. SET-UP MENU 4 USER1(ALL) OK? YES/NO 7 When the MENU button is pressed, the display of the menu screen disappears.
Setup (initial settings) (continued) Menu protection method Menu protection release method By switching to the menu protect mode, it is possible to disable the setup menu even if the MENU button on the front panel is pressed. 1 1 2 Press the MENU button. A select screen for the major menu items is displayed on the video monitor, and the names are displayed in the counter display. 2 Press the RESET button.
Setup (initial settings) (continued) System frequency switching NO.25 SYSTEM FERQ Recordable format Playback permissible format Synchronized signal 1080/59.94i (HD_LP) 720/59.94p (HD_LP) 720/60.00p (HD_LP) (Only the variable frame rate signal can be recorded.) 1080/59.94i 1080/60i 720/59.94p 720/60.00p 480/59.94i (50M, 25M, DV, DVCAM) HD_REF (59.94Hz, 60Hz) SD_REF (59.
Setup menus Menus which are displayed The menus displayed differ depending on the setting selected for menu item No.25 SYSTEM FREQ. Menu No.25 SYSTEM FREQ NO.
Setup menus (continued) Menu No.25 SYSTEM FREQ NO.
Setup menus (continued) Menu No.25 SYSTEM FREQ NO.
Setup menus (continued) Video output signal adjustments The control matrix for the adjustments is shown in the table below. This function is not available for IEEE1394 digital output. When “CMPNT” has been selected as the menu item No.
Setup menus (continued) SYSTEM No./Item 05 ENCODER SEL 06 V LEVEL CTRL 12 SYS H (HD) 14 SYS SC (SD) 36 Description of setting For setting whether to perform the various adjustments for the video output signals using this VTR or using an external encoder remote controller. 0001 LOCAL : The various adjustments for the video output signals are performed using this VTR.
Setup menus (continued) BASIC SYSTEM (continued) No./Item 25 SYSTEM FREQ 26*1 HD SYS H ADV Description of setting For selecting the system frequency. For details, refer to “Procedure for shifting the system frequency" (page 31). 0000 59/60 : The 59.94 Hz or 60 Hz system frequency is selected. 0001 50i/25P : The 50 Hz or 25 PsF system frequency is selected. At this setting, the 1080/25 PsF format signals can be recorded and played back in the same way as with the 1080/50i format. 0002 23/24 : The 23.
Setup menus (continued) BASIC (continued) No./Item 006 DISPLAY SEL Description of setting For setting what the information to be superimposed. 0000 TIME : Only the data is displayed. (“Data” refers to the CTL, TC or UB value selected by the COUNTER button.) 0001 T&STA : The data and operation status are displayed. 0002 T&S&M : The data, operation status and mode are displayed. 0003 T&RT : The data and REC TIME are displayed. 0004 T&YMD : The data and REC DATE (year/month/day) are displayed.
Setup menus (continued) Formats for playback BASIC (continued) No./Item Description of setting For setting the field frequency. 030*1 0000 59/23 : HD The field frequency is set to 59.94/23.98 Hz. FREQUENCY 0001 60/24 : The field frequency is set to 60/24 Hz. The field frequency which is set here takes effect only when there is no input which supports the OUT REF setting. If there is an input which supports the setting, the field frequency is consistent with the field frequency of input.
Setup menus (continued) OPERATION No./Item Description of setting 100 SEARCH ENA To set the transition method to search mode (stick operation). 0000 STICK : Shift to the search mode when the SEARCH button is pressed or when the stick is operated. 0001 KEY : Do not shift to the search mode unless the SEARCH button is pressed. 101 SHTL MAX For setting the maximum speed in the shuttle mode. 0000 X8.4 : 8.
Setup menus (continued) OPERATION (continued) No./Item Description of setting 115* EJECT SW INH For setting whether to restrict the operation of the EJECT button on the front panel. 0000 REC : Operation is inhibited while the unit is in the recording mode. 0001 OFF : The EJECT button can be operated in all operation modes. 118*1 SP MODE INH For selecting whether to enable or disable recording on a tape which has been recorded using a format other than DVCPRO HD-LP.
Setup menus (continued) OPERATION (continued) No./Item 1 155* AUTO REC Description of setting No./Item For setting whether the recording/stop is executed automatically in conjunction with the Recording Mark of the HD SDI input signals from our camera recorder or not. 0000 OFF : Do not to execute the recording/stop automatically. 0001 TYPE1 : To execute the recording/stop automatically in conjunction with the Recording Mark in the LTC information added to the HD SDI.
Setup menus (continued) OPERATION (continued) No./Item 1 181* TYPE-A NEAR Description of setting For setting (in increments of 0.1 V) the voltage level at which the counter flashes as warning for TYPE-A battery (selected as the menu item No.180 BATTERY SEL item). Use when adjusting the settings for multiple batteries or new type batteries. 0000 10.6 : : 12.9 0023 : : 0044 15.0 When this item has been set to a voltage level close to 15.
Setup menus (continued) EDIT No./Item 1 302* CONFI EDIT Description of setting For selecting whether to perform simultaneous playback during editing. 0000 OFF : Simultaneous playback is not performed. 0001 ON : Simultaneous playback is performed. For selecting how to connect the digital audio edit IN 303*1 AUD EDIT IN points. 0000 CUT : Cut processing 0001 FADE : V-fade processing 1 304* AUD EDIT OUT For selecting how to connect the digital audio edit OUT points.
Setup menus (continued) TAPE PROTECT No./Item TIME CODE Description of setting 400 For setting the time to be taken before the unit is set STILL TIMER in the tape protection mode when it is left standing in the STOP or STILL status. (Units: S = seconds, min = minutes) 0000 0.
Setup menus (continued) TIME CODE (continued) No./Item 1 506* REGEN MODE 507*1 EXT TC SEL 508*1 BINARY GP Description of setting Description of setting 511* DF MODE For selecting the time code to be used when an external time code is used. 0000 EXT_L : The LTC information of the TIME CODE IN connector is used. 0001 SLTC : The LTC information added to the serial signals which are supplied to the HD SDI IN connector is used.
Setup menus (continued) VIDEO No./Item Description of setting For selecting the type of internal standard signals. 601* 0000 100%CB : VIDEO INT A 100% color bar signal is selected. SG 0001 75%CB : A 75% color bar signal is selected. 0002 SMPTE : An SMPTE color bar signal is selected. 0003 ARIB : An ARIB color bar signal is selected. 0004 BLACK : A black signal is selected. For selecting how to process the serial input.
Setup menus (continued) VIDEO (continued) No./Item 1 651* HUE STYLE (SD)*DW 653 Y LVL (HD)*UP 654 Pb LVL (HD)*UP 655 Pr LVL (HD)*UP 656 BK LVL (HD)* UP 658 Y LVL (SD)*DW 659 Pb LVL (SD)*DW Description of setting For setting the axis of revolution for the chroma phase adjustment of the SD SDI output and analog composite output. 0000 Pb-Pr : The axis rotates in a perfect circle on the SDI (component style) vectorscope.
Setup menus (continued) VIDEO (continued) No./Item Description of setting 665 For adjusting the setup ( or black) level of the HD SDI, SETUP LVL analog component output, SD SDI output and analog (AJ-HD1400P) composite output. (–10 o to +10 o) 50 –10% : : BK LVL 0.0% 150 (AJ-HD1400E) : : 250 +10.0% This setting takes effect when “CMPST” has been selected as the menu item No.650 setting.
Setup menus (continued) VIDEO (continued) No./Item 1 692* UMID POS Description of setting No./Item This sets the line on which the UMID information is to be superimposed. 0000 BLANK 0001 12L : : 17L 0006 : : 0008 19L z The line selected for the menu item No. 501 VITC POS-1 and No. 502 VITC POS-2 settings cannot be selected for this item. z The default settings are not restored even if the RESET button is pressed while holding down the SEARCH button.
Setup menus (continued) AUDIO No./Item Description of setting 1 701* CH1 IN LV For setting the reference level of the analog audio input (CH1). 0000 4dB 0dB 0001 0002 –20dB 0003 –60dB 702*1 CH2 IN LV For setting the reference level of the analog audio input (CH2). 0000 4dB 0dB 0001 0002 –20dB 0003 –60dB 706 CH1 OUT LV For setting the reference level of the analog audio output (CH1). 0000 4dB 0dB 0001 0002 –20dB 707 CH2 OUT LV For setting the reference level of the analog audio output (CH2).
Setup menus (continued) AUDIO (continued) No./Item Description of setting No./Item Description of setting 750 ANA CH1/2 SEL For selecting the channel for the signal output to the analog audio output terminal CH1/CH2. 0000 CH1/2 0001 CH3/4 0002 CH5/6 0003 CH7/8 782 EMBD CH SEL Set the channels to multiplex SD-SDI output. 0000 CH1-4 : 0001 CH5-8 : When tape other than DVCPRO HD (LP) is played, CH1 to CH4 is always multiplexed.
Setup menus (continued) DIF No./Item Description of setting 880* DIF SPEED For setting the transfer speed of the IEEE1394 digital interface output. 0000 S100 : 100 Mbps 0001 S200 : 200 Mbps 0002 S400 : 400 Mbps When S100 has been selected as this item’s setting, DVCPRO HD format signals cannot be input or output. 882*1 DIF IN CH For setting the input channel. 0000 0 : : 0063 63 The input channel is fixed at the channel corresponding to the number specified.
Setup menus (continued) MENU No./Item A02 P.ON LOAD Description of setting The unit starts with the selected user default loaded when the power is turned on. 0000 OFF : The unit starts with the previous set values. 0001 USER1 : The unit starts with the selected user 1 loaded. 0002 USER2 : The unit starts with the selected user 2 loaded. 0003 USER3 : The unit starts with the selected user 3 loaded. Set value for SYSTEM menu is not loaded. A04 The setup menu item is stored to the PF1 button.
