Camera A15 and A35 Bullet Camera Quick Start Guide 1
Network Bullet Camera·Quick Operation Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. About This Document This manual applies to the following models. Model A15 A35 This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
Network Bullet Camera·Quick Operation Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Bullet Camera·Quick Operation Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Network Bullet Camera·Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network Bullet Camera·Quick Operation Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
Network Bullet Camera·Quick Operation Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30℃~+60℃,or -40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use.
Network Bullet Camera·Quick Operation Guide Table of Contents 1 Appearance Description ................................................................. 8 2 Installation ...................................................................................... 9 3 Setting the Network Camera over the LAN .................................. 13 4 Accessing via Web Browser ................ Error! Bookmark not defined.
Network Bullet Camera·Quick Operation Guide 1 Appearance Description 1 2 3 4 5 6 Figure 1-1 Bullet Camera Overview Table 1-1 Description No.
Network Bullet Camera·Quick Operation Guide 2 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. Make sure all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Make sure the power supply is matched with your required voltage to avoid damage.
Network Bullet Camera·Quick Operation Guide ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly. Steps: 1. Attach the drill template on the wall.
Network Bullet Camera·Quick Operation Guide Figure 2-2 Secure the Camera to the Ceiling 3. Adjust the Lens. 1). Loosen the adjustable nut on the bracket. 2). Adjust the panning angle [0~360°] of the camera. 3). Adjust the tilting angle [0~90°] of the camera. 4). Rotate 0~360° to adjust azimuth angle of the image. 5). Tighten the adjustable nut to complete the installation.
Network Bullet Camera·Quick Operation Guide Figure 2-3 3-axis Adjustment 12
Network Bullet Camera·Quick Operation Guide 3 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change the IP of network camera. The following figure shows the cable connection of network camera and PC: Figure 3-1 Wiring over LAN Set the IP address of the camera for accessing via LAN.
Network Bullet Camera·Quick Operation Guide Refer to the following introductions to set IP address with the Advidia Camera Finder Utility software (for more detailed instructions please download the Camera Finder manual from the Advidia Website www.advidia.com/support): After launching the Advidia Camera Finder software, it automatically searches the online devices from the subnet where your computer is located. This search may take 30 seconds or more depending on network size.
Network Bullet Camera·Quick Operation Guide Click the refresh icon to refresh the online device list manually. The newly discovered devices will be added to the list. Note: You can click on each column heading to order the information. Modify device information Steps: 1). Select the device(s) to be modified in the device list as shown in Figure 3-3. 2). Click on “File” and select “Login Manager” as shown in Figure 3-4 to enter the username and password information of selected device(s). 3).
Network Bullet Camera·Quick Operation Guide Figure 3-4 Login Manager Figure 3-5 Launch Edit Table 16
Network Bullet Camera·Quick Operation Guide Figure 3-6 Edit Table 5) Enter the desired IP address (or range if changing the IP address of more than one device) of the network camera in the address field of the edit table and click Apply Network Changes. You can also select “Dynamic IP” if you would prefer to have an IP address assigned by your network router. The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”.
Network Bullet Camera·Quick Operation Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version Steps: 1) Open the web browser.
Network Bullet Camera·Quick Operation Guide Figure 4-1 Login Interface 5) Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
Network Bullet Camera·Quick Operation Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in 20
Network Bullet Camera·Quick Operation Guide Figure 4-4 Install Plug-in 6) Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login.
