Digital Camera User Manual
Table Of Contents
- 1 Introduction
- 2 Installation
- 3 General Use
- 4 Control Panel
- 5 System Settings
- 5.1 General Settings
- 5.2 Menu Settings
- 5.3 Presentation Settings
- 5.4 Call Quality
- 5.5 Audio
- 5.6 Video
- 5.7 Security
- 5.8 Network
- 6 Peripheral Equipment
- 6.1 Interfaces
- 6.2 Document Camera
- 6.3 DVD / VCR
- 6.4 Additional Cameras
- 6.5 Additional Microphones
- 6.6 Stereo Speaker Kit
- 6.7 Telephone Add-On
- 6.8 Dual Monitor
- 6.9 XGA Monitors and Projectors
- 6.10 VESA Display Power Management
- 6.11 Digital Monitor Power Management
- 6.12 Extended Display Identification Data (EDID)
- 7 Appendices
- Appendix 1: Technical Specifications
- Appendix 2: Bandwidth Information for TANDBERG Endpoints
- Appendix 3: Environmental Considerations
- Appendix 4: Guidelines for Setting up Rooms for Video Meetings
- Appendix 5: Security
- Appendix 6: Using the File System
- Appendix 7: Web Interface
- Appendix 8: Connecting the System to PRI/T1
- Appendix 9: Connecting the System to the Switched 56 Network
- Appendix 10: Connecting the System to ISDN Using NT1 Network Adapters
- Appendix 11: TANDBERG Cameras
- Appendix 12: Remote Control (TRC3 / TRC4)
- Appendix 13: Cisco CallManager
- Appendix 14: Diagnostics Tools for IP
- Appendix 15: System Upgrade
- Appendix 16: Declaration of Conformity
- Appendix 17: Dimensions
- Appendix 18: Protocols Supported
- Appendix 19: Cable Specifications
- 8 Glossary
- 9 Index
TANDBERG Edge 75/85/95 MXP
viii
Route the power cord so as to avoid it being walked on or pinched by items placed upon or
against it. Pay particular attention to the plugs, receptacles and the point where the cord exits
from the apparatus.
Do not tug the power cord
If the provided plug does not fit into your outlet, consult an electrician.
Never install cables, or any peripherals, without first unplugging the device from it's power
source.
*Always use the power supply (AC-DC adapter) provided with this product.
*Replace only with power supply (AC-DC adapter) specified by TANDBERG.
*Never connect attached power supply (AC-DC adapter) to other products.
Servicing
Do not attempt to service the apparatus yourself as opening or removing covers may expose
you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to
qualified service personnel.
Unplug the apparatus from it's power source and refer servicing to qualified personnel under
the following conditions:
- If the power cord or plug is damaged or frayed.
- If liquid has been spilled into the apparatus.
- If objects have fallen into the apparatus.
- If the apparatus has been exposed to rain or moisture
- If the apparatus has been subjected to excessive shock by being dropped.
- If the cabinet has been damaged.
- If the apparatus seems to be overheated.
- If the apparatus emits smoke or abnormal odor.
- If the apparatus fails to operate in accordance with the operating instructions
Accessories
Use only accessories specified by the manufacturer, or sold with the apparatus.
Communication lines
Never touch uninstalled communication wires or terminals unless the telephone line has been
disconnected at the network interface.
Do not use communication equipment to report a gas leak in the vicinity of the leak.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord (ISDN
cables).
* Applies to the following products: T150 MXP, T550 MXP, T770 MXP, T880 MXP, T990 MXP, T1500 MXP, T1000 MXP,
T2000 MXP, T3000 MXP Profile, Tandberg Codec 3000 MXP, Tandberg Tactical MXP, Edge 75/85/95 MXP.