Digital Camera User Manual
Table Of Contents
- 1 Introduction
- 2 Installation
- 3 General Use
- 4 Control Panel
- 5 System Settings
- 5.1 General Settings
- 5.2 Menu Settings
- 5.3 Presentation Settings
- 5.4 Call Quality
- 5.5 Audio
- 5.6 Video
- 5.7 Security
- 5.8 Network
- 6 Peripheral Equipment
- 6.1 Interfaces
- 6.2 Document Camera
- 6.3 DVD / VCR
- 6.4 Additional Cameras
- 6.5 Additional Microphones
- 6.6 Stereo Speaker Kit
- 6.7 Telephone Add-On
- 6.8 Dual Monitor
- 6.9 XGA Monitors and Projectors
- 6.10 VESA Display Power Management
- 6.11 Digital Monitor Power Management
- 6.12 Extended Display Identification Data (EDID)
- 7 Appendices
- Appendix 1: Technical Specifications
- Appendix 2: Bandwidth Information for TANDBERG Endpoints
- Appendix 3: Environmental Considerations
- Appendix 4: Guidelines for Setting up Rooms for Video Meetings
- Appendix 5: Security
- Appendix 6: Using the File System
- Appendix 7: Web Interface
- Appendix 8: Connecting the System to PRI/T1
- Appendix 9: Connecting the System to the Switched 56 Network
- Appendix 10: Connecting the System to ISDN Using NT1 Network Adapters
- Appendix 11: TANDBERG Cameras
- Appendix 12: Remote Control (TRC3 / TRC4)
- Appendix 13: Cisco CallManager
- Appendix 14: Diagnostics Tools for IP
- Appendix 15: System Upgrade
- Appendix 16: Declaration of Conformity
- Appendix 17: Dimensions
- Appendix 18: Protocols Supported
- Appendix 19: Cable Specifications
- 8 Glossary
- 9 Index
TANDBERG Edge 75/85/95 MXP
18
3.2 Using the Remote Control
The system is controlled with a remote control. Think of the remote control as a mobile phone
with number keys and call keys. Use the arrow keys and press OK to navigate through the
menus. The system’s most commonly used functions are also accessible directly from the remote
control. The Infra Red (IR) sensor for the remote control is located in front of the Camera. There
is also a second IR-sensor located in the front of the Codec itself, which will be automatically
enabled if the Camera is not connected.
The remote control (TRC 3)
1. Mic Off turns your microphone on and
off, see Mic off
.
2. Arrow keys are used for navigation in
the menu and for moving the camera*
when the menu is hidden, see
Navigation
.
3. Volume + and – adjusts the Codec
volume only and not the monitor's
volume, see Volume + and -
.
4. The Layout key toggles between full
screen and different display layouts, see
Layout
.
5. Cancel takes you back one step in the
menu system. Use Cancel to delete
characters in an input field, see
Navigation
. Press and hold the Cancel
key for 1 second to close the menu.
6. Press the Call key to place a call, see
Make a Call
.
7. Camera presets define specific camera
positions. Move the camera to the
desired position and press and hold a
number key for 1 second to save the
current camera position to that number
key. To activate a preset whilst in a call,
simply press and release that number
key, see Camera Presets
.
8. Snapshot takes a snapshot of your video
only while you are in a call, see Take
New Snapshot.
9. The Presentation key switches to a
predefined presentation source. If the
Presentation key is held down for 1
second then the Presentation video
sources menu will appear, see
Presentation Key
.
10. Press OK/Menu to show the menu and
to select menu items, see Navigation
.