P-05C INSTRUCTION MANUAL 11.
Thank you for selecting the “docomo PRIME series P-05C”. Read this manual before use to correctly operate your P-05C. About manual of P-05C Basic Package The operating procedures for the P-05C are also published as in P-05C Handset Battery Pack P20 (With Warranty and LUMIX Phone Panel “使いかたガイド (Guide)” on-screen manual installed onto your P50) FOMA terminal, and “Instruction Manual (Detailed Version)” as a PDF.
Contents FOMA Terminal ································2 What You can Do with P-05C···········3 Part Names and Functions ··············4 Precautions······································6 Handling Precautions ···················· 14 Introduction ▶ P.
Introduction FOMA Terminal 2 P-05C supports W-CDMA・GSM/GPRS・Wireless LAN system. Because the FOMA terminal uses radio waves, you cannot use it in places where the radio waves do not reach, where they are weak even outdoors, such as inside tunnels, basements, or buildings, or out-of-service area. You might not be able to operate the FOMA terminal even when you are in a place with a fine view such as in a high-rise building or apartment.
What You can Do with P-05C ECO NAVI ▶P.40 Start by Voice i-concier AUTO-GPS ▶P.66 The AUTO-GPS function offers the useful services which provide you with information such as about weather forecast, tour spots, and shops around you. ▶P.32 You can call up a function just by saying the relevant keyword. This is useful when you do not know which menu contains the function you want to use or when you want to activate a function quickly. ※ This function is available in Japanese mode only. Wi-Fi ▶P.
Part Names and Functions Introduction ❶ ❾ ❷ ❷Earpiece For listening to the other party’s voice ❸ ❸Display/Touch panel � � ❹ ❺ ❻ ❼ � � � ❽ ❹mMenu key For showing the Main Menu ❺lMail key For showing the Mail Menu ❻dStart key For starting to talk ❼rClear key/i-Channel key � 4 ❶Light sensor For sensing brightness (Do not cover it with your hands or do not put a sticker on it. Doing so might disable detecting the brightness.
Side ▼ key For turning down the earpiece volume during a call vShutter key For shooting a subject by the camera xMulti key For showing the Task menu Introduction Flash fmark An IC card is installed. Use it for Osaifu-Keitai or iC communications. Camera For shooting portraits and/or landscapes LUMIX Phone panel Remove this when attaching/removing the battery pack, UIM, and microSD card.
Introduction Precautions ALWAYS FOLLOW THESE DIRECTIONS ■Before using the FOMA terminal, read these safety precautions carefully so that you can use it correctly. After reading the precautions, keep them in a safe place. ■Be sure to observe these safety precautions to prevent you or those around you from inflicting injury and to avoid unnecessary damage to the property.
General precautions for FOMA terminal, batteries, adapters, and UIM Warning Don’t Don’t Do not use, store or leave the FOMA terminal and its accessories in places with a high temperature such as near fire or places exposed to direct sunlight, or in cars under the blazing sun. Fire, burns, or injury may result. Don’t Do not place the FOMA terminal or its accessories inside cooking appliances such as microwave ovens or high-pressure containers. Fire, burns, injury or electric shock may result.
Introduction Do Do Keep out of the reach of babies and infants. Accidental swallowing or injury may result. Take special care when you use the FOMA terminal for a long time with the adapter connected. If you use the i-αppli programs, talk on the videophone, watch 1Seg programs and so on for a prolonged period of time while charging, the temperature of the FOMA terminal, battery pack or adapter may rise.
Do If the display part or camera lens is broken, be careful about broken glasses or the exposed interior of the FOMA terminal. A film is coated on the surface of the display area and the plastic panel is used for the surface of the camera lens, making it hard for the glass to break into pieces. However, if you touch the damaged or exposed parts by mistake, you may injure yourself. Caution Don’t Don’t Don’t Don’t Do not swing around the FOMA terminal by its strap, antenna or other parts.
Introduction Do View the display in a sufficiently light place keeping a certain distance from your eyes. Otherwise, your eyesight may become impaired. Don’t Precautions for batteries ■ Check the description on the label of the battery pack for the type of battery. Description Li-ion 00 Do Type Lithium-ion battery Danger Don’t Don’t Don’t 10 Do not let any metal object such as a wire come in contact with the battery terminals.
Precautions for adapters Warning Don’t Don’t Don’t Don’t Do not use the AC adapter and desktop holder in humid places such as a bathroom. Fire, burns or electric shock may result. The DC adapter is for use only in a negative (-) grounded vehicle. Do not use it in a positive (+) grounded vehicle. Fire, burns or electric shock may result. If a thunderstorm is nearby, do not touch the adapter. Otherwise, you may receive an electric shock.
Introduction If liquids such as water get in the adapter, unplug the power cord immediately from the outlet or Pull the cigarette lighter socket. power plug Fire, burns or electric shock may out result. Before cleaning, pull the power plug out of the outlet or cigarette lighter socket. Pull the Fire, burns or electric shock may power plug result.
■List of materials used Connector terminal cover Camera lens area Side ▲ key, Side ▼ key, Multi key Sheet (Battery compartment) Charging terminal Where it is used Material/Finishing PC/UV coating ABS ABS/UV coating PET Magnesium Stainless steel/ nickel plating + tin plating PC, Elastomer/UV coating PMMA/surface hard coating + AR coating + water-repellent coating ABS/UV coating PC Material/Finishing Battery stopper (inside LUMIX Phone panel), Lock claw for LUMIX Phone panel Resin part Battery terminal
Where it is used Material/Finishing Introduction LUMIX Body ABS/aluminum foil + UV coating Phone panel Camera ring area (Inside) Aluminum/alumite treatment 14 Camera ring area (Middle) Acrylic urethane Camera ring area (Outside)※1 PC/UV coating Camera ring area (Outside)※2 PC/tin vapor deposition + UV coating Connector terminal side ABS/UV coating Projection part of PC/aluminum vapor deposition connector terminal side + UV coating Sheet of battery PET compartment surface (large/small) Label PP 1Seg Tip
■Do not rub or scratch the display part with metals. Doing so might cause damage to the part, resulting in trouble or malfunction. ■Carefully read each instruction manual attached to battery pack, adapter, or desktop holder. Introduction ■When using the FOMA terminal, ensure that you shut the cover for the connector terminal. Dust or water might enter into the FOMA terminal, causing malfunction. ■Do not use the FOMA terminal with the LUMIX Phone panel left removed.
Introduction ■Note the following points when you store a battery pack: Storage in a fully charged state (the state immediately after charging is completed) Storage with no battery power left (the state you cannot turn on the power of the handset due to battery drain) These may lower the battery pack’s performance and shorten its operating life.
■Radio frequencies The radio frequencies for the Bluetooth function of the FOMA terminal are as follows: 2.4 FH 1 FH 1 : Indicates radio facilities that use 2400 MHz frequencies. : Indicates modulation is the FH-SS system. : Indicates that an estimated interference distance is 10 meters or less. : Indicates that all radio frequencies 2400 MHz through 2483.5 MHz are used, and that the frequencies for mobile object identifiers shall not be avoided.
Introduction ■Cautions on Using 2.4 GHz Devices The bandwidth of the WLAN devices is assigned to the in-plant radio stations for identification of mobile objects used in production lines of a factory (a license is required), specified low power radio stations (a license is not required), or amateur radio stations (a license is required), in addition to home electric appliances such as a microwave oven, industrial/scientific/ medical devices. 1.
3 Before Using With the arrow mark facing up, fit the tab side of the battery pack to the FOMA terminal securely, and then push the battery pack in direction B while pressing it against direction A. Attaching UIM/Battery Pack 1 Remove the LUMIX Phone panel. Insert the UIM. With the golden IC surface downward, push the UIM slowly to the end while pressing surface. Take care not to damage the IC. When you remove the UIM Pull it out slowly while sliding.
Basic Operation About UIM The UIM is an IC card that holds your information such as phone numbers. You cannot use the FOMA terminal for communications such as voice/videophone calls, i-mode, or sending/receiving mail, unless the UIM is inserted.
Charging Using Desktop Holder Power socket AC Adapter AC Adapter’s plug Call/Charging indicator Back case Engraved surface Connector terminal Desktop Holder 1 With the engraved surface of the connector of the AC Adapter (option) face up, plug the connector straight into the connector terminal of the desktop holder (option). 2 Pull out the AC Adapter’s plug, and plug it into a household power socket of 100 V AC.
Turning Power ON 1 Press and hold h for at least one second. Basic Operation After the Wake-up display is displayed, the Stand-by display appears. To turn off the power 1. Press and hold h for at least two seconds▶Select “YES” Configuring Initial Setting The Initial Setting display appears when you turn on the power for the first time. 1 Set the date and time. You can set the date and time. You can also correct the date and time automatically. 2 Set your Terminal Security Code.
Notifying Your Caller ID on the Other Party’s Phone m▶TEL function▶Dial/Receive setting ▶Caller ID notification 2 Select “Activate/Deactivate”. 3 Select “ON”. m▶本体設定 (Setting) ▶文字表示／入力 (Text display/input) ▶Select language 2 Select “English”. The “バイリンガル (Select language)” setting is saved on the UIM. If you hear the guidance requesting your caller ID, either set the Caller ID notification or add “186” first and then try calling again.
Screen Explanation Viewing Display/Icon Status icon Battery level (estimate) ············ A Bluetooth device is connected. Basic Operation ··········· A microSD card is inserted. Full Low When is shown, charge the battery. Depending on the usage state, the battery level indication might significantly vary. Radio waves reception level (estimate) Strong Weak ············ You are out of the FOMA service area or radio waves do not reach. ·········· Vibrator is set.
Notification icon ······ New i-mode mail or SMS ······ Missed call ······ Record message ······ Videophone record message ····· 使いかたガイド (Guide) ··· Client mode ····· Access point mode ··· Shows the site of the URL ····· Start by voice 1 ····· Quick search ··· Slideshow-Touch ······ Pedometer Proceed to respective functions from icons, etc. You can proceed to respective functions from “Status icon”, “Notification icon”, “Desktop icon”, date and time. 1. Oo▶Use Mo to highlight an icon, etc.
Navigation Displays and Key Operations Operating Speed Selector Basic Operation Key operations you can perform while you are operating a function are shown at the bottom of the display. (Navigation displays) ■Key assignments and basic navigation displays Moves the cursor or highlighted display up. (Hold down to scroll continuously.) Scrolls the page up. Vo Moves the cursor to the right. Scrolls forward page by page. (Hold down to scroll continuously.) Oo Fixes the operation.
Operating by Turning Speed Selector In some displays, you can turn the speed selector to select items the same way as you press Mo, and can move the cursor. Turning direction Operation example Menu Operation Main Menu Press m from the Stand-by display to show Main Menu. In this manual, the descriptions of operating procedures are given mainly starting with the Stand-by display. Menu icons Selecting pictograms, etc.
Basic Operation Simple Menu Functions Starting with Simple Operation Simple Menu is a menu focusing on only basic functions for easy operation. By setting “Simple menu” using the Kisekae tool, you can show the Simple Menu by pressing m from the Stand-by display. Some operating procedures or items which appear on the display in Simple Menu differ from the ones described in this manual.
Using Touch Panel You might not be able to operate the Touch Panel depending on the i-αppli program. Basic Touch Panel Operations Operation Main Operation Select/OK Touch Simply tap the touch panel. Touch an item or control key on the touch panel. Move the cursor or highlighted item on Long touch Touch and keep your finger the touch panel Touch an item long on the list, etc. on the touch panel. Continuous operation Touch a control key long for fast forward, etc.
Basic Operation Operation Pull apart/Pinch together Slide two fingers apart or pinch together. 30 Main Operation Magnification/Reduction The image or display will zoom in or out. ■Control key For Speed selector operations, dial key operations, or Submenu operations, you can perform the equivalent operations by touching the control keys (long touch). ■Slide lever By adjusting the position of the slide lever, you can set the volume level, etc.
Displaying Touch Menu You can display the Touch Menu by touching the touch panel from the Stand-by display. Home Menu Customize Menu When “ ” is touched, the Customize Menu is displayed. On the Customize Menu, you can register short-cut icons up to 27 and activate any of the functions by touching the corresponding short-cut icon. When “ ” is touched, the Normal Menu is displayed. You can operate any of the functions by touching the corresponding icon on this menu. The Normal Menu icons cannot be changed.
Basic Operation Using Start by Voice Using Guide You can call up the function by voice. The first time you use this function, select “利用する (Use)” ). on the usage information display, or press c( This function is available in Japanese mode only. You can search and check the operating methods of the functions you want to know and use. You can execute some functions from “使いかたガイド (Guide)”. This function is available in Japanese mode only. 1 Press and hold d for at least one second.
Character Entry You can enter characters on the Registration display for Phonebook entries or the Composition display for mail messages, etc. 1 Select a input mode. Press l( input modes. Convert/fix characters. 1. Press No to specify the area to be converted. 2. Press Bo to move the cursor onto the candidate list. 3. Press Mo to select a conversion candidate. 4. Press Oo to fix the character. Enter characters. By repeatedly pressing a numeric key, you can enter other characters assigned to the key.
Entering “タダの菓子” in the text of an i-mode mail message. Basic Operation 1 2 l▶l( ) ▶Select the text field. Enter hiragana characters in Kanji/Hiragana input mode. 3 Use Co to move the cursor to the right of “の”. 4 Use Bo to move the cursor onto the candidate list ▶Use Mo to highlight “タダ の” and press Oo( ). 5 Use Bo to move the cursor onto the candidate list▶Use o M to highlight “菓子” and press Oo( ). た → Press 4 once and Vo once. だ → Press 4 once and a once. の → Press 5 five times.
Sound/Screen Setting Changing Ring Tone Changing the ring tone for incoming voice calls 1 1 2 Select “Phone”. 3 Use Bo to adjust the volume. Select “Phone”. Press c( ) to check the content actually played back or displayed. To set a ring tone for mail messages, videophone calls, and so on, select the corresponding item. 3 Select “Select ring tone”. 4 Select a type of ring tone. 5 Select a folder▶Select a ring tone. m▶Setting▶Sound/Vib.
Basic Operation Using Manner Mode Setting Keypad Sound OFF With a single key press, you can set a tone from the FOMA terminal such as a ring tone, keypad sound, and alarm sound silent. When you start Manner Mode, not a sound but the vibration notifies you of incoming calls or messages. You can silence a Keypad sound for when you press a key. 1 2 Press and hold s for at least one second. “ ” appears on the Stand-by display. To release Perform the same operation.
Changing Display Brightness You can adjust the brightness of the display. You can also set to automatically adjust the display brightness according to the ambient light. 1 m▶Setting▶Backlight/Illum. ▶Backlight Select “Brightness”▶Select “ON”. 3 Press Bo to adjust the brightness. Lighting off/Power Saver Mode You can set the display brightness to OFF. You can also set the time that elapses before Power Saver Mode activates.
Changing Font Size Using Kisekae Tool Changing the size of all the characters to “X-large”. You can set the ring tone, Stand-by display, menu icons and others at a time. Basic Operation 1 2 Select “Character size”. 3 Select “X-large”. Select “Separate setting” when you want to set the character size of each function separately.
Changing Illumination When Receiving Changing call Illumination for voice calls. 1 m▶Setting▶Backlight/Illum. ▶Illumination setting Select “Illumination in call” ▶Select “Illumination”. 3 Select “Phone”. 4 1 Press and hold 5 for at least one second. “ To set illumination such as for mail messages and videophone calls, select the corresponding menu. ” appears. To release Perform the same operation. Select a color. If you select “Gradation”, color 1 to 12 light up in sequence.
eco Mode Autostart This setting ensures that the mode will be automatically set to the eco Mode when the remaining battery level has dropped below the set level. “Battery level” of “eco mode autostart” is set to “40%” in default. Basic Operation 1 m▶Setting▶Battery ▶eco mode autostart 2 Select “ON”. 3 Set each item▶c( When the “eco mode autostart” is set to “ON”, “ (gray)” will be displayed.
Terminal Security Code “0000” at purchase This is a four-to-eight digit number for deleting all files or changing settings. When the display for entering the Terminal Security Code appears, enter your four-to-eight digit code ). and press Oo( To change 1. m▶Setting▶Lock/Security▶Change security code Determining at the time of contract “お客様サポート (User support)” is available in Japanese only.
PIN Unblocking Key (PUK) Basic Operation The PIN unblocking key (PUK) is the eight-digit number for releasing the blocked PIN1 code and PIN2 code. You cannot change this code by yourself. If you enter a wrong PIN unblocking key (PUK) 10 times in succession, the UIM is locked. In that case contact one of docomo Shops. Dial Lock You can set your FOMA terminal not to be used by a third party. You can do no operations other than answering calls and turning on/off the power. 1.
Omakase Lock When you have lost your FOMA terminal or in other cases, you can lock your personal data (such as Phonebook entries) and the IC card function of Osaifu-Keitai by contacting DOCOMO. For details on Omakase Lock, refer to “User’s Guide [Basic Usage]”. Original Lock Keypad Lock You can lock functions which utilize personal information such as Phonebook entries or schedule events. 1. m▶Setting▶Lock/Security▶Lock ▶Enter your Terminal Security Code ▶Select a level for Original Lock.
Setting Incoming Call Restriction Resetting to Default Basic Operation You can set whether to receive (accept) or not to receive Resetting the Function Settings to Default (reject) incoming calls depending on the reason, such as from You can reset the items on “Function List”, which are the parties which has not been registered in Phonebook or indicated by . (See page 99) incoming calls from any parties who do not notify you of their might include the functions The items indicated by phone numbers.
Call Telephone Making a Call/Videophone Call Making a Call by Entering the Phone Number 1 Enter a phone number starting with a city code. 2 Press d to make a call. 3 ) to make a videophone call. Search a Phonebook entry by the name stored in Phonebook 1 Press Xo. 2 Select “Search name”. Enter the reading of the name from the first character. You can use another search method such as “Search phone No.”, and “Search e-mail”.
Making a Call with Redial/Received Calls Making an International Call 1 Press Vo(Redial) or Co(Received calls). 2 Select a call record▶d You can use WORLD CALL to make an international call from Japan. Contact “docomo Information Center” on the back page of this manual for inquiries about details on WORLD CALL. When using international carriers other than DOCOMO, contact them. Press c( ) to make a videophone call.
Receiving a Call/Videophone Call 1 A call comes in. The ring tone sounds and the Call/Charging indicator lights. 2 Press d to answer the call. When a videophone call comes in You can receive the videophone call the same way as with a voice call. The substitute image is sent to the other party. Press h to end the call. By activating Record Message, you can record a caller’s voice/video message when you cannot answer the call.
Using Public Mode (Drive Mode) Using Public Mode (Power Off) Once you activate Public mode (Drive mode), the guidance is played back telling that you cannot answer the call as you are currently driving or in a place where you should refrain from speaking on the phone. Then the call is disconnected.
Using Various Network Services ■Network services available The following are the DOCOMO network services available for the FOMA terminal.
Using Voice Mail Service Using Call Waiting Service 1 1 m▶TEL function▶Voice mail service To activate the service 1. Select “Activate”▶Select “YES”. You can also specify a ring time. Connect To play back the message 1. Select “Play messages”▶Select “Play (voice call)” or “Play (videophone)”▶Select “YES”. 2. Operate following the voice guidance. m▶TEL function▶Other network serv. ▶Call waiting To activate the service 1. Select “Activate”▶Select “YES”. Answer an Incoming Call during a Call Press d.
Emergency Call Emergency Calls Calls to police Calls to fire station and ambulance Calls for accidents at sea Phone number 110 119 118 Connect This FOMA terminal supports “Emergency Location Report”. When you make an emergency call such as at 110/119/118, information about the place where you are dialing from (location information) is automatically notified to emergency-response agencies such as police stations.
Connect Using Overseas 52 International Roaming (WORLD WING) is a service that allows you to use the FOMA terminal with the phone number and mail address you use in Japan, in a service area of the overseas carrier partnered with DOCOMO. It enables you to continue using the voice call, SMS and i-mode mail settings without having to make any changes.
Making a Call to Outside the Country You Stay in 1 Sending i-mode Mail 0(for at least one second) ▶Enter numbers in order of country code →area code (city code) →destination phone number. Once you subscribe to i-mode, you can exchange e-mail messages over the Internet. You can attach within 2 Mbytes of up to 10 files (photos, moving pictures, etc.) with body text added. For details on i-mode mail, refer to “Mobile Phone User’s Guide [i-mode] FOMA version”.
Sending Deco-mail Sending Decome-Anime You can change the color or size of characters or background You can create impressive messages by inserting text or color, or insert images or Deco-mail pictograms. images into a Flash file. 1 2 Connect 3 ) You can also select “Decome-Template” to create Deco-mail. Enter an address and subject. 1 l▶Create new Deco-Anime 2 Enter an address and subject. 3 Select the text field▶d When the text field is selected, the prediction conversion candidates appear.
Displaying Received i-mode Mail Replying to i-mode Mail 1 Select a folder. Press c( displayed. 2 Enter each item. Select an i-mode mail message. 3 Press c( 1 l▶Inbox 2 3 ) while an i-mode mail is ). Forwarding i-mode Mail Connect 1. m( ) while an i-mode mail is displayed ▶Reply/Forward▶Forward 2. Enter each item. 3. Press c( ). When you receive an i-mode mail message, “ ” appears on the upper area of the display.
Checking New i-mode Mail Sorting i-mode Mail You can check the i-mode Center for a new mail message or Message R/F. You can use “Auto-sort” to sort received/sent i-mode mail messages into a folder such as “Business” or “Friend” which has been created in advance. Sorting mail messages, which come from the address stored in the Phonebook, into a folder 1 Press and hold l for at least one second. Connect When checking is completed, the following display appears.
Early Warning “Area Mail” Receiving Area Mail You can receive information such as about earthquake alerts that are issued from the Japan Meteorological Agency as an Area Mail message. ” lights and the When an Area Mail message arrives, “ buzzer for Area Mail sounds. The received content of some messages is automatically displayed. To erase the displayed content, select “OK”. You can receive Area Mail messages even when you are not contracted to use i-mode.
Displaying Received SMS Message 1 l▶Inbox Phonebook Storing Phonebook Entries 2 Select a folder. Storing New Phone Numbers/Mail Addresses, etc. 3 Select an SMS message. You can store Phonebook entries in the FOMA terminal (Phone) or on the UIM. 1 Connect 2 Press and hold Xo for at least one second. Select “Phone”. The display for entering a name appears. Enter a name and proceed. When storing entries onto the UIM Phonebook Select “UIM”.
Storing Phonebook Entries from Redial/ Received Call 1 Press Vo(Redial) or Co(Received calls). 2 Highlight a call record and press m( )▶Select “Add to phonebook”. 3 Select “Phone”▶Select “New”. Enter each item. 5 Press c( ). 1 2 Xo▶Search and select a Phonebook entry. m( )▶Edit phonebook ▶Select an item to be edited ▶Edit the contents. 3 Press c( 4 Select “YES”. ). Deleting Phonebook Entries Register a birthday to the Phonebook to have it shown on Schedule.
i-mode/Full Browser Search Displaying i-mode Sites i-mode is a service that enables you, by using the display of the terminal supporting i-mode, to use online services such as site access, Internet access, and i-mode mail. i-mode is a pay service that is available on a subscription basis. For details on i-mode, refer to “Mobile Phone User’s Guide [i-mode] FOMA version”. You can display SSL/TLS※-compatible pages via FOMA terminal.
Displaying Websites Designed for PC Switching Browsers 1 1 m▶imode/web▶Full Browser Home By default, a confirmation display appears asking whether you want to use Full Browser. 2 Select “YES”. Search You can browse Internet websites designed for PCs using the You can switch to Full Browser to show the Internet websites Full Browser function. incorrectly displayed by i-mode. Note that you are charged a high communication fee for The billing system differs between i-mode and Full Browser.
Viewing and Operating Sites Saving Site Contents Operations on site viewing display Scroll display/Move highlighted/ Move the pointer: Mo Select an item (link): Oo( Search 1 ) Return to previous page: l( Forward to next page: i( If you save the page once you visited as a screen memo, you can easily refer to it without connecting to i-mode. ) 2 ) “ ” or “ ” appears while accessing by Full Browser.
i-Channel 1 Press r. Search This service distributes information such as news and weather forecast to i-Channel mobile phones. The automatically received latest information flows on the Stand-by display by tickers. You can read it on the i-Channel list by pressing -r. Further, two types of channels, “Basic channel” provided by DOCOMO and “Okonomi (Optional) channel” provided by IPs (Information Providers) are available.
Search Map/GPS 64 GPS is a function that receives signals from the GPS satellites and acquires information on the FOMA terminal’s position. This GPS function cannot be used as a navigation device for airplanes, vehicles or people or as a device for conducting high-accuracy surveying. If it is used for these purposes or even if it is used for other purposes, bear in mind that NTT DOCOMO INC.
Checking Current Location You can start GPS compatible i-αppli, and you can read a map of current or specified location. At purchase, “地図アプリ (Map Application)” is set. You can locate your current location by GPS. You can also display a map using this location information and send this information as an i-mode mail. You are not charged a packet communication fee for checking your current location.
Search Using AUTO-GPS Your current location is automatically positioned, and by sending your location information periodically to your GPS service provider, you are enabled to receive a variety of services according to your location, such as weather forecast, shopping guide, or sightseeing information around. To use a service that supports the AUTO-GPS function, use the AUTO-GPS function compatible i-αppli to establish the AUTO-GPS service information for respective services.
Camera Viewing and Touching Operation of Finder Display You can use the camera to shoot still images or moving pictures. You can use the touch panel to operate the camera when shooting. You can check the settings. By touching, you can make the display brighter than usual. By touching, you can display the still image or the moving picture you have shot in Picture Album. By touching, you can display the submenu. You can change the settings. Shows the remaining time of recordable moving pictures.
Shooting Still Images/Moving Pictures Shooting Still Images 1 Press v. 2 Press v. You can display the still image or the moving picture you have shot in Picture Album. You can detect a person’s face on the still image you have shot and expand it, or add corrective effects to the detected face. You can also play expressive slide shows with the effect function. The still image is automatically saved. 1 Shooting Moving Pictures 1 Press v.
Shooting in Various Ways Shooting Still Images Using Omakase Choice You can shoot 6 or 8 still images one after the other. The FOMA terminal automatically displays the successfully-shot still images judging from the focus and composition. 1 v▶MENU▶Burst Shoot ▶Omakase choice 2 Select a burst shooting interval ▶Press v. To enlarge the best-shot still image. ” is added to three superior images. “ Slide left or right to enlarge the next or the previous image.
1Seg Enjoy Using 1Seg 70 ■Using 1Seg 1Seg is a service provided by television entrepreneurs (broadcasting stations). You are not charged a communication fee for receiving video and audio. For about fee charged by NHK, contact NHK. ※You are charged a packet communication fee for browsing “Data broadcasting site” and “i-mode site”. You might be charged an information fee for using some sites (i-mode pay sites).
Setting Channels When you activate 1Seg for the first time or change the area you are in, you need to operate “Channel setting”. Select “Auto channel setting” to enable you to search automatically for broadcast stations you can watch. You need to set this function with the 1Seg antenna extended when you are in a terrestrial digital TV broadcasting service area. 1 Watching 1Seg 1 Press and hold c for at least one second. 1Seg starts and the viewer display appears.
Viewing and Operating Viewer Display Displayed while you are watching a 1Seg program Video being recorded Program Information (outline) Video Switch Visual Image/Caption Caption Airwave Reception Level (estimate) Data Broadcasting Strong Weak “ ” appears out of the broadcasting area.
Setting Timer Watching or Recording 1Seg Set the date and time, a channel, and program name, and enter them to the TV Timer List or Timer Recording List. When the set time arrives, watching or recording starts. 1 m▶CAMERA/TV/MUSIC▶1Seg 2 Select “TV timer list” or “Timer recording list”. 3 Press c( 4 Enter each item. 5 Press c( Playing Recorded Video 1 m▶Data box▶1Seg 2 Select “Video”▶Select a file. ). ).
Music Enjoy Music&Video Channel 74 Music&Video Channel is a service which automatically delivers up to about two-hours sound programs at night just by selecting your favorite music programs etc. in advance. Further, you can enjoy high-quality video program of up to about one-hour. Programs are updated periodically and you can enjoy the delivered programs at any time such as on commuting. ■Before using Music&Video Channel Music&Video Channel is a pay service that is available on a subscription basis.
Downloading Chaku-uta Full® Music Files You can download Chaku-uta Full® music files from sites. 1 Select a Chaku-uta Full® music file from a downloadable site. 2 Select “Save”▶Select “YES”. 3 Select a destination folder. “Chaku-uta Full” is a registered trademark of Sony Music Entertainment Inc. ■Handling music files You can use music files saved on the microSD card for personal use only.
i-αppli/i-Widget Enjoy i-αppli is a software program for terminal supporting i-mode. By downloading various software programs from the i-mode site, you can use your FOMA terminal more conveniently. You can automatically update the stock price information or weather information, and enjoy games without accessing network. i-Widget is a useful function for gaining easy access to frequently used contents and tools (Widget Appli programs) such as the calculator, clock, memo pad and stock market information.
Downloading i-αppli from Sites 1 Select a software program from a downloadable site. 2 Select “OK” when downloading ends. 3 Select “YES”. When the software program is storable in “Customize Menu”, the confirmation display appears asking whether to store it. You can delete the pre-installed i-αppli programs. You can re-download deleted programs from the “P-SQUARE” site.
i-motion/Movie Enjoy i-motion is a file consisting from video, audio, and music which you can download to your FOMA terminal from i-motion sites that support i-motion. You can also set it for a ring tone. Also, by using high speed communication, you can play back smooth and high-quality movie files provided by portal sites, movie specialty sites and other sites on the Internet. When downloading or streaming an i-motion/movie file, you might receive a bulky file.
Osaifu-Keitai Osaifu-Keitai/ToruCa 1 More Convenient Osaifu-Keitai is equipped with the IC card which enables you to make payments, use coupons, enjoy stamp rallies and so on by placing the FOMA terminal over the scanning device in the stores or other locations. Furthermore, by placing the FOMA terminal over a scanning device, you can access sites and web pages, obtain the latest coupons by communication, and check the deposits of electronic money and the status of its use.
More Convenient i-concier 80 i-concier works to serve you with a pleasant life just like a clerk or concierge does. The service holds your data (area information about your neighborhood, Memo, Schedule, ToruCa, Phonebook, etc.) and sends you information, with good timing, about a variety of things according to the contents of your memo and your schedule event, your living area, your current location, or your preference or taste.
Convenient Tools Using Alarm 1 1 m▶Tool▶Alarm 2 Highlight an alarm and press c( 3 Enter each item. 4 Press c( m▶Tool▶Schedule Select a date to show a schedule event of the selected date. Select the schedule event to confirm its details. 2 m( 3 Enter each item. 4 Press c( )▶Select “New”. ). The alarm does not sound in Public mode (Drive mode), Dial Lock, “Alarm” locked in Original Lock or Omakase Lock. ). More Convenient Using Schedule ).
Using Bar Code Reader Scan a Code Access P-SQUARE by using You can use the camera to scan QR codes and others, and QR code on the right store them as files. From the scanned data, you can make calls, compose i-mode mail messages, access Internet websites, and so on. QR code for ■When scanning with Bar Code Reader accessing the site Guide frame Scan the code as large as possible within the guide frame.
Bluetooth Function You can connect your FOMA terminal to a Bluetooth device such as Wireless Earphone Set 02 (option), and can talk on the phone or play music files. Registering a Bluetooth Device to FOMA Terminal Connecting with Bluetooth Devices 1 2 m▶Tool▶Bluetooth▶Device list Select a Bluetooth device ▶Select a service to be connected. You can search and register a Bluetooth device to the FOMA terminal. You need to place the Bluetooth device to be registered standby for registration beforehand.
Wi-Fi This FOMA terminal compatible Wi-Fi. You can access the internet by connecting to your home Access point or a public wireless LAN service using Full Browser. You can enjoy on-line communication by compatible Wi-Fi devices such as portable game machine, personal computer, etc. using Access point mode.
Using Pedometer 1 Creating Handwriting Photo/Memo On the touch panel, you can draw pictures or write characters by hand onto the images or you can add decoration. The Handwriting photos/memos you have created are saved as JPEG images. 1 2 m▶Tool▶Pedometer The measurement records of your pace are displayed. From the submenu, you can switch between ON/OFF of Pedometer, or set user information. Normal Menu▶Tool ▶Handwriting photo/memo Set Background ▶Edit Handwriting photo/memo ▶Touch “Finish”.
Data Management More Convenient Using microSD Card 86 If you do not have a microSD card, you need to purchase it. P-05C supports a commercial microSD card of up to 2 Gbytes and microSDHC card of up to 32 Gbytes (As of April 2011). For the latest operation check information such as the memory capacity and manufacturers of microSD cards, access the following sites (in Japanese only). Note that the microSD cards other than published in the sites might not correctly work.
Icons on the Display : A microSD card is inserted. : Data is being read/written. (Do not remove the microSD card nor turn off the FOMA terminal.) : The microSD card is write-protected. : The microSD card cannot be used. (Insert the microSD card again. If “ ” is still displayed, execute “Check microSD” or “microSD format”.) Formatting microSD Card When you use the microSD card for the first time, you need to format (initialize) it. Be sure to use P-05C for formatting.
Copying Data to microSD Card Displaying Data Stored on microSD Card Copying a still image Displaying a still image 1 1 m▶Data box▶My picture▶l( 2 Select a folder▶Select an image. More Convenient 2 88 m▶Data box▶My picture ▶Select a folder. Highlight a still image to be copied and press m( ) ▶Select “Copy to microSD” ▶Select “Copy this”. Check Capacity of microSD Card You can display the total memory and used memory (estimated) on the microSD card. 1.
Backing up Data to microSD Card You can back up Phonebook entries, schedule events, messages, memos, bookmarks, and the settings on and information about your FOMA terminal collectively onto the microSD card. When restoring the backup data onto your FOMA terminal, they are collectively restored. Backing up data from the FOMA terminal onto the microSD card is collectively applied to all data, so emptied files in the FOMA terminal are also backed up on the microSD card.
Sending Data For infrared communications, set the receiving end terminal first, and then start sending data within 30 seconds. Connecting to a PC You can connect the FOMA terminal to a personal computer to exchange WMA files, images or other files stored on microSD card. Submenu of the data to be sent You can also access the Internet to perform data ▶Select “Send Ir data” or “iC communication. ※You need the FOMA USB Cable with Charge Function 02 transmission”. (option) or FOMA USB Cable (option).
Support Troubleshooting First of all, check to see if you need to update the software program and then update it if necessary. See page 95 for how to update software programs. When symptom persists even after you check the countermeasures for the problem you suffer, contact the “Repairs” counter listed on the back page of this manual or a repair counter specified by DOCOMO. The “Repairs” counter is available in Japanese only. Power source The FOMA terminal does not turn on.
The usable time of the battery is short. …Make sure not to leave the FOMA terminal out-of-service-area for a long time. If your FOMA terminal is left out-of-service area, it searches for radio waves to establish communications, consuming more power. …The usable time of the battery pack varies depending on the usage environment or its remaining life. …Battery packs are consumables. The usable time slightly shortens each time you charge the battery.
Warranty and After-sales Service Warranty Make sure that you have received a warranty card provided at purchase. After checking the contents of the warranty card as well as “Shop name and date of purchase”, keep the warranty card in a safe place. If you notice that necessary items of the warranty card are not filled in, immediately contact the shop where you purchased the FOMA terminal from. The term of the warranty is one year from the date of purchase.
Others 94 ◎Other points to note Make sure not to modify the FOMA terminal or its accessories. ・We might reject to repair depending on the degrees of your modification. The following might be regarded as modifications: ・To put stickers, etc. onto the liquid crystal or keys ・To decorate the FOMA terminal using adhesives ・To replace the coverings etc.
Updating Software Others This function is to check whether you need to update software programs in the FOMA terminal by connecting to the network, and if necessary, you can download some parts of software programs using packet communication, and can update the software programs. If you need to update the software programs, the DOCOMO website and “お客様サポート (User support)” in Japanese iMenu lets you know information about updating software programs.
Start Software Update from Icon Start Software Update from Menu 1 1 Select “Update notification icon” on the Stand-by display. Update notification icon Check whether you need to update software programs. Others 2 96 When update is necessary, “Update is needed” is displayed. And you can select either “Now update” or “Reserve”. When you select “Now update”, update immediately starts.
Check Harmful Data You can detect data or application programs, which might cause troubles, from among those downloaded to your FOMA terminal, and then can delete the data or stop starting the application programs. This scan function provides a certain protective measure to filter out data that might cause troubles with your FOMA terminal at the time when you browse websites or receive messages.
Options and Related Devices Combining various options with the FOMA terminal, you can realize more versatile use from personal purpose to business purposes. Some products may not be dealt in depending on the area. For details, consult a handling counter such as a docomo Shop. For details on options, refer to the user’s manuals of respective options and related devices.
Function List Inbox Outbox Draft Mail history box Compose new message Create new Deco-Anime Decome-Template Auto Deco-mail setting Check settings Reset iMenu/Search Bookmark Screen Memo Browsing history i-Channel Deco-mail Decome-Anime Compose new SMS Check mail/message Check new SMS Receive option imode/web setting Enter URL URL enter history i-Channel list Ticker display setting Reset i-Channel imode Browser Set.
CAMERA/TV/MUSIC iαppli setting Camera Others 1Seg 100 AUTO-GPS preferred set iαppli call settings iαppli volume Preferred tone αBacklight αVibrator Check settings Digicam mode Photo mode Movie mode Picture album Activate 1Seg Program guide TV timer list Timer recording list Recording result TVlink Channel list Channel setting User setting MUSIC Player Music&Video Channel Data box Trace info Auto-start setting Disp.
microSD Guide Voice recorder Device list Bluetooth Wi-Fi Register New Devices Bluetooth ON/Bluetooth OFF Accept registered Accept dialup devices Bluetooth settings Client mode Access point mode mixi setting PicMate setting Tool Dictionary Phrases/Store word Phonebook DIGA link (DLNA) DIGA remote controller Voice announce Common phrases Store word Search phonebook Add to phonebook UIM operation Phonebook set./Check Forwarding image Rec. msg./Voice memo Dialed/Received call Play/Delete msg.
Visual preference Select image Auto redial as voice Videophone setting Call duration/charge Koe-no-Takuhaibin Ntfy switch-mode Reject videophone Hands-free switch V.phone while packet Call duration/charge Notify cost limit Reset total TEL function Missed call notice Other network serv.
Backlight/Illum. Text display/input Time Change security code UIM setting Scanning function Timer lock ON at close IC card lock setting Setting Battery Other setting eco mode setting eco mode autostart Use history Battery level USB mode Bluetooth Headset microphone Femtocell Wi-Fi Touch menu open set.
Overseas NW search 3G/GSM setting Network search setting PLMN setting Display operator name Display area status Re-search icon set. Inquiries (overseas) Sub clock setting Bar incoming when roam Missed call notice Others Overseas setting Mail/Message usage set Network service Overseas use guide i-concier 104 Roaming guidance Int’l dial assistance imode service set. Profile Osaifu-Keitai Map&GPS set./history Map setting GPS button setting Location request set. AUTO-GPS Positioning mode set.
Specific Absorption Rate (SAR) of Mobile Phone SAR Certification Information Ministry of Internal Affairs and Communications Website: http://www.tele.soumu.go.jp/e/sys/ele/index.htm Association of Radio Industries and Businesses Website: http://www.arib-emf.org/index02.html (In Japanese only) NTT DOCOMO, INC. Website: http://www.nttdocomo.co.jp/english/product/sar/ Panasonic Mobile Communications Co., Ltd. Website: http://panasonic.
European RF Exposure Information This mobile phone complies with the EU requirements for exposure to radio waves. Your mobile phone is a radio transceiver, designed and manufactured not to exceed the SAR* limits** for exposure to radio-frequency (RF) energy, which SAR* value, when tested for compliance against the standard was 0.496 W/kg. While there may be differences between the SAR* levels of various phones and at various positions, they all meet*** the EU requirements for RF exposure.
station antenna, the lower the output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the U.S. government-adopted requirement for safe exposure. The tests are performed in various positions and locations (for example, at the ear and worn on the body) as required by FCC for each model. The highest SAR value for this model phone as reported to the FCC when tested for use at the ear is 1.
Intellectual Property Right Copyrights and Portrait Rights Powered by JBlend™ Copyright 2002-2011 Aplix Corporation. All rights reserved. JBlend and JBlend-related trademarks are trademarks or registered trademarks of Aplix Corporation in Japan and other countries. f is a registered trademark of FeliCa Networks, Inc. microSDHC Logo is a trademark of SD-3C, LLC.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, INC. and any use of such marks by NTT DOCOMO, Inc. is This software is based in part on the work of the Independent JPEG under license. Other trademarks and trade names are those of their Group. respective owners. This product contains IrFront of ACCESS CO., LTD. IrFront is a MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS registered trademark or trademark of ACCESS CO., LTD. in the and Thomson.
Others 110 Content providers are using the digital rights management technology for Windows Media contained in this device (“WM-DRM”) to protect the integrity of their content (“Secure Content”) so that their intellectual property, including copyright, in such content is not misappropriated. This device uses WM-DRM Software to play Secure Content (“WM-DRM Software”).
Access the following for checking or changing the contents of your contract, or for applying to respective services, and asking for related documents: From i-mode ｉMenu ▶ お客様サポート (User support) ▶ お申込・お手続き (Applications/Procedures) ▶ 各種お申込・お手続き (Respective applications/procedures) Packet communication charges free From PC My docomo (http://www.mydocomo.com/) ▶ 各種お申込・お手続き “お客様サポート (User support)” and My docomo are available in Japanese only. You will need your “network ID” for the access from i-mode.
Loss or theft of FOMA terminal or payment of cumulative cost overseas (available 24 hours a day) ■ From DOCOMO mobile phones International call access code for the country you stay at -81-3-6832-6600* (toll free) Failures encountered overseas (available 24 hours a day) ■ From DOCOMO mobile phones International call access code for the country you stay at -81-3-6718-1414* (toll free) * You are charged a call fee to Japan when calling
General Inquiries Repairs 0120-005-250 ■ From DOCOMO mobile phones ■ From land-line phones (toll free) * Service available in English, Portuguese, Chinese, Spanish, and Korean. * Unavailable from part of IP phones. (Business hours: 9:00 a.m. to 8:00 p.m.) ■ From DOCOMO mobile phones ■ From land-line phones (In Japanese only) (No prefix) 151 (toll free) * Unavailable from land-line phones, etc.
