Operator's Manual
Table Of Contents
- What is new in publication version 7.2?
- 1 Introduction
- 1.1 Before you start
- 1.2 Important safety instructions and additional information
- Important information regarding safety
- Disposal of the system
- Product safety
- General care
- Accessory box
- Meter
- Power off meter
- Automatic power-off
- Shut down meter
- Automatic shutdown
- Battery Pack
- Touchscreen
- Electromagnetic compatibility (EMC)
- Electrostatic discharge (ESD)
- Wireless connectivity
- Radiofrequency radiation exposure information
- Local Area Network: protection from unauthorized access
- Wired network connection
- 1.3 System components
- 1.4 Overview of the meter
- 1.5 Overview of the code key reader
- 1.6 Overview of the Accu-Chek Inform II Base Unit
- 1.7 Overview of the Accu-Chek Inform II Base Unit Hub
- 1.8 Overview of the accessory box
- 1.9 Reagents and consumables
- 1.10 Instructions for initial setup
- 2 Powering Up and Entering an Operator ID
- 3 Patient Glucose Testing
- 3.1 Information regarding blood glucose testing
- 3.2 Performing a patient glucose test
- Overview of test procedure
- Entering or selecting the patient ID
- Entering the patient ID manually
- Selecting the patient ID from a list
- Entering a patient ID with barcode scanner
- Confirming or selecting the test strip lot
- Patient identification information
- Inserting test strips
- Obtaining a blood sample
- Applying a blood sample
- Results screen
- Adding comments
- Add barcode content to a result
- Additional Patient Test
- 4 Glucose Control Testing
- 5 Review Results
- 6 Storing Test Strip, Control Solution, and Linearity Solution Information in the Meter
- 7 Linearity Testing
- 8 Proficiency Testing
- 9 Initial Startup
- 9.1 Connecting the base unit
- 9.2 Installing or replacing the battery pack
- 9.3 Docking the meter
- 9.4 Initial setup on the meter
- 9.5 Opening the Setup Menu
- 9.6 Date and time format
- 9.7 Display options and optional tests
- 9.8 Options for test strips
- 9.9 Options for glucose control tests
- 9.10 Value ranges (normal, critical, reportable)
- 9.11 Options for Operator ID Entry
- 9.12 Patient ID options
- 9.13 Creating a setup password
- 9.14 Setting the date and time
- 9.15 Beeper options
- 10 Maintenance and Care
- 11 Troubleshooting
- 12 General Product Information
- A Appendix
- B Appendix
- C Supplement for Other Test Entry
- D Supplement for Observed Test Sequence
- E Supplement for Enhanced Workflows
- F Appendix for Accu-Chek Inform II Base Unit (legacy version)
- G Limited Warranty
- Index
30
08424705001 (04) 2021-06 USA • Accu-Chek Inform II Operator’s Manual Version 7.2
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Radiofrequency radiation exposure Information: This
device has been tested and meets the FCC/ISED RF expo-
sure guidelines. Nevertheless, the device should be used in
such a manner that the potential for human contact during
normal operation is minimized.
Local Area Network: protection
from unauthorized access
If this product is connected to a local area network, this
network must be protected against unauthorized access.
In particular, it must not be linked directly to any other
network or the Internet. Customers are responsible for
the security of their local area network, especially in pro-
tecting it against malicious software and attacks. This
protection might include measures, such as a firewall, to
separate the device from uncontrolled networks as well
as measures that ensure that the connected network is
free of malicious code.
Wired network connection If connected to a local area network, the Accu-Chek
Inform II Base Unit or Accu-Chek Inform II Base Unit Hub
must be protected against unauthorized access by means
of a strong password management. For additional
information about the Accu-Chek Inform II Base Unit or
Accu-Chek Inform II Base Unit Hub, refer to the
Accu-Chek Inform II Base Unit Hub Operator’s Manual or
the “Technical Note” stored on the Accu-Chek Inform II
Base Unit as a PDF file (see page 191 of this manual).
Or contact Roche Customer Support Center for technical
assistance.
Observe your own facility guidelines on password
management where available, or apply the following
rules:
NOTICE
Changes or modifications made to this equipment not
expressly appro
ved by (Roche Diagnostics GmbH) may
void the FCC authorization to operate this equipment.
CAUTION
The UNII-1 band (5150-5250 MHz) is only allowed for
indoor use in Canada.