Operator's Manual
Table Of Contents
- What is new in publication version 7.2?
- 1 Introduction
- 1.1 Before you start
- 1.2 Important safety instructions and additional information
- Important information regarding safety
- Disposal of the system
- Product safety
- General care
- Accessory box
- Meter
- Power off meter
- Automatic power-off
- Shut down meter
- Automatic shutdown
- Battery Pack
- Touchscreen
- Electromagnetic compatibility (EMC)
- Electrostatic discharge (ESD)
- Wireless connectivity
- Radiofrequency radiation exposure information
- Local Area Network: protection from unauthorized access
- Wired network connection
- 1.3 System components
- 1.4 Overview of the meter
- 1.5 Overview of the code key reader
- 1.6 Overview of the Accu-Chek Inform II Base Unit
- 1.7 Overview of the Accu-Chek Inform II Base Unit Hub
- 1.8 Overview of the accessory box
- 1.9 Reagents and consumables
- 1.10 Instructions for initial setup
- 2 Powering Up and Entering an Operator ID
- 3 Patient Glucose Testing
- 3.1 Information regarding blood glucose testing
- 3.2 Performing a patient glucose test
- Overview of test procedure
- Entering or selecting the patient ID
- Entering the patient ID manually
- Selecting the patient ID from a list
- Entering a patient ID with barcode scanner
- Confirming or selecting the test strip lot
- Patient identification information
- Inserting test strips
- Obtaining a blood sample
- Applying a blood sample
- Results screen
- Adding comments
- Add barcode content to a result
- Additional Patient Test
- 4 Glucose Control Testing
- 5 Review Results
- 6 Storing Test Strip, Control Solution, and Linearity Solution Information in the Meter
- 7 Linearity Testing
- 8 Proficiency Testing
- 9 Initial Startup
- 9.1 Connecting the base unit
- 9.2 Installing or replacing the battery pack
- 9.3 Docking the meter
- 9.4 Initial setup on the meter
- 9.5 Opening the Setup Menu
- 9.6 Date and time format
- 9.7 Display options and optional tests
- 9.8 Options for test strips
- 9.9 Options for glucose control tests
- 9.10 Value ranges (normal, critical, reportable)
- 9.11 Options for Operator ID Entry
- 9.12 Patient ID options
- 9.13 Creating a setup password
- 9.14 Setting the date and time
- 9.15 Beeper options
- 10 Maintenance and Care
- 11 Troubleshooting
- 12 General Product Information
- A Appendix
- B Appendix
- C Supplement for Other Test Entry
- D Supplement for Observed Test Sequence
- E Supplement for Enhanced Workflows
- F Appendix for Accu-Chek Inform II Base Unit (legacy version)
- G Limited Warranty
- Index
254
08424705001 (04) 2021-06 USA • Accu-Chek Inform II Operator’s Manual Version 7.2
F.3 Technical data
Specification Base unit (legacy version) Power supply unit
Height 4.33 in / 110 mm (max.) 1.38 in / 35 mm +
AC plug (1.1-1.6 in / 28-40 mm)
Width 4.65 in / 118 mm (max.) 2.01 in / 51 mm
Length 4.06 in / 103 mm (max.) 3.43 in / 87 mm
Weight Accu-Chek Inform II Base Unit
(legacy version)
615 g with wall mount
N/A
User interface LED (tricolor: red, green, blue) LED: green
Operating temperature 37 to 122 °F
3 to 50 °C
32 to 104 °F
0 to 40 °C
Storage conditions (long-term
storage)
41 to 104 °F / 5 to 40 °C at 10 - 85% RH (non-condensing)
Humidity (operating) 10 - 90 % RH (non-condensing)
Air pressure 0.7 to 1.06 bar
70 to 106 kPa
N/A
Input voltage +7.5 V DC 100 to 240 V AC
Input frequency DC 50 to 60 Hz
Input current 1.7 A (max) 350 to 150 mA
Interfaces Charge contacts
IR port
RJ45 Ethernet
USB type B
DC connector
Replaceable AC input contacts
Data transfer rate IR: 9.6K - 115K bps
Ethernet: 10 Mbps half-duplex
USB: 12 Mbps
N/A