Operator's Manual
Table Of Contents
- What is new in publication version 7.2?
- 1 Introduction
- 1.1 Before you start
- 1.2 Important safety instructions and additional information
- Important information regarding safety
- Disposal of the system
- Product safety
- General care
- Accessory box
- Meter
- Power off meter
- Automatic power-off
- Shut down meter
- Automatic shutdown
- Battery Pack
- Touchscreen
- Electromagnetic compatibility (EMC)
- Electrostatic discharge (ESD)
- Wireless connectivity
- Radiofrequency radiation exposure information
- Local Area Network: protection from unauthorized access
- Wired network connection
- 1.3 System components
- 1.4 Overview of the meter
- 1.5 Overview of the code key reader
- 1.6 Overview of the Accu-Chek Inform II Base Unit
- 1.7 Overview of the Accu-Chek Inform II Base Unit Hub
- 1.8 Overview of the accessory box
- 1.9 Reagents and consumables
- 1.10 Instructions for initial setup
- 2 Powering Up and Entering an Operator ID
- 3 Patient Glucose Testing
- 3.1 Information regarding blood glucose testing
- 3.2 Performing a patient glucose test
- Overview of test procedure
- Entering or selecting the patient ID
- Entering the patient ID manually
- Selecting the patient ID from a list
- Entering a patient ID with barcode scanner
- Confirming or selecting the test strip lot
- Patient identification information
- Inserting test strips
- Obtaining a blood sample
- Applying a blood sample
- Results screen
- Adding comments
- Add barcode content to a result
- Additional Patient Test
- 4 Glucose Control Testing
- 5 Review Results
- 6 Storing Test Strip, Control Solution, and Linearity Solution Information in the Meter
- 7 Linearity Testing
- 8 Proficiency Testing
- 9 Initial Startup
- 9.1 Connecting the base unit
- 9.2 Installing or replacing the battery pack
- 9.3 Docking the meter
- 9.4 Initial setup on the meter
- 9.5 Opening the Setup Menu
- 9.6 Date and time format
- 9.7 Display options and optional tests
- 9.8 Options for test strips
- 9.9 Options for glucose control tests
- 9.10 Value ranges (normal, critical, reportable)
- 9.11 Options for Operator ID Entry
- 9.12 Patient ID options
- 9.13 Creating a setup password
- 9.14 Setting the date and time
- 9.15 Beeper options
- 10 Maintenance and Care
- 11 Troubleshooting
- 12 General Product Information
- A Appendix
- B Appendix
- C Supplement for Other Test Entry
- D Supplement for Observed Test Sequence
- E Supplement for Enhanced Workflows
- F Appendix for Accu-Chek Inform II Base Unit (legacy version)
- G Limited Warranty
- Index
138
08424705001 (04) 2021-06 USA • Accu-Chek Inform II Operator’s Manual Version 7.2
9.8 Options for test strips
This menu allows you to select options for handling lot
numbers and specify whether the operator is allowed to
add or delete reagent lots, edit the expiration date and
limit values on the meter (see “Creating a setup pass-
word” on page 145).
1 Touch the desired option to enable it:
■ Reagent Editing
– Allowed: Enables the operator to edit the reagent
information without needing a password.
– Password Needed: Enables the operator to edit the
reagent information only after entering a password.
– Not Allowed: The operator cannot edit reagent
information.
■ Strip Lot Verification
– Display only: The lot number is shown on screen but
the operator cannot confirm it or select a different
lot number.
– Confirmation: The operator must confirm the lot
number displayed and can enter alternative lot
numbers manually or via barcode scanner.
– List selection: The operator can also select from a
list of stored lot numbers.
– Scan only: Lot numbers can be verified via barcode
scanner only.
2 Touch to change to the second screen of
options,
or
touch to exit this menu without saving any
changes.
When using a data management system for configura-
tion, it is possible to fully disable the Reagent Editing
option.
Reagent Options
Allowed
Password Needed
Display only
Confirmation
List selection
Scan only
Reagent Editing
Strip Lot V
erification
Not Allowed
12:48 pm
03/17/20