Instructions / Assembly
co
Please read these instructions carefully before you start to assemble this
product and carry out the steps in the order set out in these instructions.
When encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
Care and Safety Advice
For safety purposes we strongly recommend the product to be assembled
by at least two people.
Some parts may have sharp edges. Please be careful when handling components.
Always wear gloves, eye protection, and long sleeves when assembling or performing
any maintenance on your product.
Do not attempt to assemble the product in windy or wet conditions.
Dispose of all plastic bags safely - keep them out of reach of small children.
Keep children away from the assembly area.
Do not attempt to assemble the product if you are tired, have taken drugs,
medications or alcohol, or if you are prone to dizzy spells.
When using a stepladder or power tools, make sure you follow the manufacturer's
safety advice.
Do not climb or stand on the roof.
Heavy articles should not be leaned against the poles.
Do not hang or lay on the profiles.
Keep roof and gutter clear of snow, dirt & leaves.
Heavy snow load on roof can damage the product making it unsafe to stand
below or nearby.
Keep these instructions in a safe place for future reference.
If color was scratched during assembly it can be fixed with the following tints:
White - RAL 9016
Cleaning
Instructions
When your product needs cleaning, use a mild detergent solution and rinse with cold
clean water.
Do not use acetone, abrasive cleaners, or others special detergents to clean the panels.
Before Assembly
This product must be assembled on a solid, level base / surface (such as concrete or
asphalt) and anchored to the ground.
Choose your site carefully before beginning assembly.
Sort the parts and check according to the contents parts list.
Please consult your local authorities if any permits are required prior to constructing
the product.
Tools & Equipment
T001 (Supplied)
Notes During Assembly
When encountering these icons, you are requested to either
keep the screws slightly loose or to fully tighten the screws.
orl
Steps
Step 8: Please apply silicone sealants above beam 7288 + 7290, in order to prevent water from
seeping in (drawing b).
Step 12: Please note the profile's direction (8063), the canal should be on the internal side.
Step 13: Make sure that the angle between the back wall profile and the panel supporting
profiles is 90 degrees.
Step 23: Please apply silicone sealants to the inner edges of parts 7043 & 7042 as well as to the
middle of parts 7029 + 7039 in order to prevent water from seeping in.
Step 24 a + b: Please apply silicone sealant on the inner part of 8116 & 8117 (a) and connect to
the profile (b).
Step 24 c: Adjust the gutter head's angle according to your needs and tighten screw 4043 from
the inside.
* It is possible to connect standard drainage pipes (2.07" diameter) to the gutter heads' exit.
Step 28: Important! Please make sure the frame is perfectly centered before fixing.
Step 31: Please do not cut profile 8055 unless needed.
Step 33: Please loosen the screws as shown in diagram c, set the beam exactly on top of the
poles, once done re-tighten the screws.
Step 36: Important! Do not over tighten the screws. Use compatible screws and masonry
anchors for your type of base / foundation.
Step 37: Please do not cut profile 8056 unless needed.
Step 38: Please do not cut profile 8057 unless needed.
Please do not cut the Acrylic sheets 8111 & 8113 unless needed, all precautions must be taken.
Step 42: Install the sealing strip on the outer side, as shown in the diagram.
Step 47: Note the doors' corners should be at a 90° angle. Should you have difficulties in
manipulating the doors, tap on the door's corner with a rubber mallet. (Do not tap directly on
the corner, use a small wooden plank)
Step 51: Please note! The master key attached to the doors, locks from the inside.
Step 52: Optional! Part 8531 sets the grey marked doors, thus creating smaller openings.
*Tighten all screws when completing assembly.
Please note:
Anchoring this product to the ground is essential to its stability and rigidity, and required
in order for your warranty to be valid.
The wall anchoring kit supplied with this product is suitable only for concrete walls.
Other wall types need an accordant wall fixation kit.