User's Guide

6
USING YOUR CLARISONIC
Read through this entire section before using your
Clarisonic. Prior to the first use, charge the Clarisonic
brush handle for 24 hours by plugging the charging cradle
into an electrical outlet and placing the Clarisonic in the
charging cradle, making sure the handle is in the proper
position with the brush head facing the power cord (see
diagram on page 2). Once your Clarisonic is fully charged,
it’s time to begin your Clarisonic experience. For your
convenience, your Clarisonic handle is waterproof and
may be used in the shower or bathtub. Refer to Important
Safeguards regarding the charging cradle.
The Clarisonic is designed for use with most skin types.
Your skin is constantly changing, and due to its dynamic
nature you may want to use different power levels,
different brush heads, and a shorter or longer duration.
The Clarisonic is packaged with the Sensitive brush head
(white plastic base) installed. The Normal brush head (gray
plastic base) is also included. We recommend that you first
use your Clarisonic with the Sensitive brush head at the low
power setting for a one-minute duration (this is the factory
setting). Then you can customize your Clarisonic for your
skin type: sensitive or normal brush head; normal or
low power setting; one- or two-minute duration (with
the T-TIMER™ feature enabled).
If you use makeup, remove eye makeup by hand first and
wet your skin with warm water prior to use. Liberally apply
cleanser to your skin and wet the brush head with warm
water. Then gently apply the brush to your skin, beginning
on the forehead as described in the Cleansing Timer section
below. Push the power button to turn your Clarisonic on
and gently move the brush using a small circular motion.
Pressing too hard will impede the motion of the brush and
reduce its effectiveness. The outer brushes are designed
to contain any residual mist from the oscillating of the
brush, so be sure to hold the brush head flush to your skin.
Clarisonic also effectively clarifies the neck, back, décolleté
(upper chest), shoulders, arms, and the back of the hands.
It is recommended that you do not share a brush head with
another individual. Do not share brushes if you or any other
Clarisonic user have any skin conditions. To dry the brush
after use, rub it against a towel for 5-10 seconds while the
Clarisonic is powered on (optional).
7
Your Clarisonic is programmed to operate in a variety
of power settings and brushing durations, both with and
without the T-timer feature, as described below.
POWER LEVEL
The Clarisonic Skin Care Brush offers a choice of 2 power
levels: normal and low. The power level is indicated both
audibly and visually. When the Clarisonic is turned on at the
normal power level, there are 3 ascending beeps and the
yellow light is illuminated. At the low power level, there are
3 descending beeps and the yellow light is turned off.
Power level Audible indication Visible indication
Normal 3 ascending beeps yellow light on
Low 3 descending beeps yellow light off
To toggle between the settings, hold the power button down
for 3 seconds continuously when turning on the Clarisonic.
Listen for the change in beeps to confirm the power level.
The Clarisonic will operate at this power setting until you
change it.
CLEANSING TIMER
For even and thorough cleansing of your face, the
Clarisonic features a proprietary one-minute T-timer that
beeps and pauses momentarily to indicate it is time to
move to another part of your face. We recommend that you
spend the first 20 seconds of brush time on your forehead,
20 seconds on your nose/chin region, and 10 seconds
on each cheek. The Clarisonic is factory set with a one-
minute duration. To pause the cleansing cycle for up to 30
seconds, simply press the power button. The yellow light
will flash (indicating pause mode) and the Clarisonic will
automatically remember the remaining time on the T-timer.
To resume, press the power button again. When finished,
rinse your skin with warm water and rinse the brush head
of the Clarisonic with warm water.
To change the cleansing duration, turn your Clarisonic
on and hold the power button for at least 10 seconds. At
around 3 seconds, you will hear three tones (related to the
Power Level) and then you will hear beep tones relating to
the optional cleansing times and interval beeps.
Cleanse your face
using our T-timer
recommended
duration and zones
as shown above.
Gently move the brush
using a small circular
motion.
forehead
20
seconds
nose/
chin
20
seconds
each
cheek
10
seconds
clarisonic.com
1-888-525-2747